Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The UART0 on H6 is available at PH bank (and PF bank, but the PF one is
muxed with SD card).
Add pinmux configuration.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As the Allwinner H6 chip has a new memory map, its GIC MMIO address is
thus different.
Change the address on H6.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
H6 has different SRAM A2 address, so the ATF load address is also
different.
Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 has a different RVBAR address with A64/H5.
Add conditional RVBAR configuration into the code which does RMR switch.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC come with a totally new memory map.
Add basical definition of the new memory map into a header file, and let
the cpu.h header include it in the situation of H6.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
sunxi: change SUNXI_HIGH_SRAM option to SUNXI_SRAM_ADDRESS
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Simon Baatz [Mon, 23 Jul 2018 22:22:19 +0000 (00:22 +0200)]
sunxi: enable SATA on Banana Pi M2 Berry
Banana Pi M2 Ultra and M2 Berry are very similar boards. SATA can be
enabled exactly the same as for M2 Ultra introduced in
commit daa8b75a5527 ("sunxi: enable SATA on Banana Pi M2 Ultra").
Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini [Mon, 30 Jul 2018 20:06:04 +0000 (16:06 -0400)]
fs-test.sh: Update expected result output
Given 0dc1bfb7302d ("fs: fat: cannot write to subdirectories") we have
changed how the FAT code works from creating the illegal file "./file"
and instead rejecting the path. The correct behavior would be to write
"file" to "." but not writing an illegal file is a step in the right
direction. For now, update the expected output to account for the
failure.
Tom Rini [Mon, 30 Jul 2018 20:02:29 +0000 (16:02 -0400)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
Peng Fan [Tue, 24 Jul 2018 06:27:18 +0000 (14:27 +0800)]
tools: genboardscfg: move buildman path to first
To system which has kconfiglib installed, genboardscfg will
use system kconfiglib, we need it use U-Boot owned version,
so move the buildman path to first.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 23 Jul 2018 13:55:14 +0000 (15:55 +0200)]
dm: Change CMD_DM enabling
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.
This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.
The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com> Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Michal Simek [Mon, 23 Jul 2018 06:38:56 +0000 (08:38 +0200)]
Kconfig: Remove trailing whitespaces in prompt
Remove additional trailing whitespaces in prompt reported by kconfiglib:
warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Felix Brack <fb@ltec.ch>
The reverted commit didn't support the scenario where there are less
DRAM banks in U-Boot than in Linux.
Also, it didn't introduce any new functionality, only limitaion.
User could just increase MEMORY_BANKS_MAX if it's too small. Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Sat, 21 Jul 2018 17:53:59 +0000 (12:53 -0500)]
configs: omap3_logic: Remove USB Storage and enable CONFIG_BLK
With the pending requirement for CONFIG_BLK, this patch removes
the USB_STORAGE option which assumes that DM_USB is enabled, but isn't
yet available for the omap2340 musb glue among other issues. Once
the USB issues are resolved, a future patch can enable them again.
sandbox: compile both TPM stack versions and drivers
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org>
test/py: tpm2: switch from 'tpm' to 'tpm2' command
While using the 'tpm' command should work on most cases, this test suite
only works with TPMv2 and since the work to make both versions build at
the same time, we might end up having both 'tpm' (TPMv1) and 'tpm2'
(TPMv2) commands available at the same time. Ensure this test suite
always use the right one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org>
tpm: allow TPM v1 and v2 to be compiled at the same time
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning] Signed-off-by: Tom Rini <trini@konsulko.com>
The TPM_DRIVER_SELECTED symbol was used in one of the initial series
about TPMv2 but its use has been dropped, making these selects
useless, remove them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 27 Jul 2018 11:56:59 +0000 (07:56 -0400)]
openrd: Once again shrink binary size
With some recent changes to relevant drivers here the openrd board
(openrd_client in this case) does not fit within its size constraint.
We can however drop the slightly extended baudrate table and then the
duplication of mtdparts/mtdids in the default environment. These
defaults are set in the environment by the 'mtdparts' command and
otherwise referenced throughout the code.
Prior to this patch is fdtdec_setup_memory_banksize() incorrectly
ignoring the "status" field. This patch fixes that by testing the status
with fdtdec_get_is_enabled() before using a memory node.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Sampson [Wed, 27 Jun 2018 13:38:58 +0000 (14:38 +0100)]
patman: Split alias entries on arbitrary whitespace
Previously the first three words in a git-mailrc alias entry could only
be separated by spaces. git-send-email and Mutt both allow arbitrary
whitespace here.
Signed-off-by: Adam Sampson <ats@offog.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Sampson [Wed, 27 Jun 2018 13:38:57 +0000 (14:38 +0100)]
git-mailrc: Replace tabs with spaces in alias entries
patman's _ReadAliasFile only splits on spaces, not tabs, so the entries
for dinh and maxime weren't being recognised as valid. I'll fix patman
in a separate patch, but this makes all the entries consistent.
Signed-off-by: Adam Sampson <ats@offog.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Fri, 22 Jun 2018 19:03:19 +0000 (13:03 -0600)]
ARM: tegra: avoid using secure carveout RAM
If a secure carveout exists, U-Boot cannot use that memory. Fix
carveout_size() to reflect this, and hence transitively fix
usable_ram_size_below_4g() and board_get_usable_ram_top(). This change
ensures that when U-Boot copies the secure monitor code to install it, the
copy target is not in-use for U-Boot code/data.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 22 Jun 2018 19:03:18 +0000 (13:03 -0600)]
ARM: PSCI: Enable the PSCI node
When fixing up the DT to report PSCI support, explicitly enable the node.
DTs may ship with the node disabled in case a PSCI implementation is not
present, and expect any PSCI implementation to enable the node if they are
actually present.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 22 Jun 2018 19:03:17 +0000 (13:03 -0600)]
ARM: PSCI: Support PSCI v0.2
Enhance the PSCI DT editing code to allow setting a PSCI v0.2 compatible
value in the DT. The CONFIG_ option is added to the whitelist to match the
existing PSCI_1_0 option. While not adding new options to Kconfig isn't
ideal, I figure it's better to keep related options together.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Bibek Basu [Fri, 22 Jun 2018 19:02:28 +0000 (13:02 -0600)]
ARM: tegra: implement RAM repair
RAM repair has a few pre-requisites:
1) PMIC power supply (rail) enabled.
2) PMC CRAIL power partition powered.
3) Fuse clock active (it's the default).
4) PLLP reshift branch enabled (it's the default, when PLLP is active).
RAM repair also only need run whenever specific partitions are powered
(main SoC and CCPLEX respectively); RAM repair does not need to be
triggered when any other partition changes state.
start_cpu() needs to be re-ordered slightly to match these requirements.
Note that C0NC and CE0 aren't required for RAM repair to
operate, but they also do no harm, so the entire of powerup_cpus() is
moved rather than splitting it up. The call to remove_cpu_resets() is
moved last to ensure that all other actions complete before releasing
reset; since the PMC power partitions are now enabled early, releasing
reset is what causes the CPUs to start executing code, and RAM repair must
complete before the CPU boots.
Note that this commit is the result of squashing a numbmer of commits
in NVIDIA's downstream L4T branch, hence the multiple signoffs below.
Signed-off-by: Bibek Basu <bbasu@nvidia.com> Signed-off-by: Sandipan Patra <spatra@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 22 Jun 2018 19:02:27 +0000 (13:02 -0600)]
Revert "tegra: Introduce SRAM repair on tegra124"
This reverts commit 701b7b1d2cf657d435d2bd6caf43d0247d37220d. It will
be immediately replaced by a different implementation that is more
complete and runs are more targetted times.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sat, 21 Jul 2018 01:49:27 +0000 (19:49 -0600)]
tegra: Indicate that binman makes all three output files
Use GNU make pattern rules to indicate that a single run of binman
produces all three Tegra output files. The avoids make running binman
three times (perhaps in parallel) and those instances inteferring with
each other.
See http://patchwork.ozlabs.org/patch/944611/ for the bug report.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):
- network drivers
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
<-- phydev is connected to dev which is UCLASS_ETH device
if (priv->phy_of_handle > 0)
dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
<-- phydev->dev->node is overwritten by phy-handle DT node
As result, UCLASS_ETH device can't be used any more for DT accessing.
This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 25 Jul 2018 17:59:22 +0000 (12:59 -0500)]
net: phy: Clean up includes of common.h
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.
Also, common.h includes config.h as the first thing it does, so don't
include it directly.
Series-to: u-boot
Series-cc: Grygorii Strashko <grygorii.strashko@ti.com>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.
[1] https://patchwork.ozlabs.org/cover/940104/
END Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Tue, 17 Jul 2018 20:02:30 +0000 (15:02 -0500)]
phy: Break include cycle
Because some phy wants to export some functions [1], export.h was
including the whole phy subsystem which pulls in lots of stuff that
causes some ordering and redefinition issues. Split out the only part
that is actually needed in export.h and include it there and in phy.h.
[1] commit 95279315076c ("board/ls2085rdb: Export functions for
standalone AQ FW load apps")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 16 Jul 2018 20:33:51 +0000 (15:33 -0500)]
arm: Prevent redefinition error in fsl-layerscape
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Murali Karicheri [Thu, 28 Jun 2018 19:26:34 +0000 (14:26 -0500)]
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).
It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.
Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Chris Packham [Mon, 9 Jul 2018 09:34:00 +0000 (21:34 +1200)]
net: mvgbe: convert to DM
Add driver model support to the mvgbe driver. As a temporary measure
both DM and non-DM uses are supported. Once all the users have been
converted the non-DM support can be dropped.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Tested-by: Michael Walle <michael@walle.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andrew Thomas [Thu, 21 Jun 2018 23:21:01 +0000 (16:21 -0700)]
initialize net_mode.if_type
if_type is not correctly initialized
Failure to initialize if_type means that grub2/efinet sends
a bogus arp request. It therefore gets no response. On Raspberry Pi 3B+
this leads to a pause at:
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 4 Jul 2018 00:36:42 +0000 (19:36 -0500)]
net: Read bootfile from env on netboot_common()
Instead of depending on a env callback for bootfile, read it explicitly.
We do this because the bootfile can be specified on the command line and
if it is, we will overwrite the internal variable. If a netboot_common()
is called again with no bootfile parameter, we want to use the one in
the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 4 Jul 2018 00:36:39 +0000 (19:36 -0500)]
net: When checking prerequisites, consider boot_file_name
For net_boot_common, we allow the serverip to be specified as part of
the boot file name. For net commands that require serverip, include that
source as a valid specification of serverip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Alexander Graf <agraf@suse.de>
Joe Hershberger [Wed, 4 Jul 2018 00:22:55 +0000 (19:22 -0500)]
net: Check subnet against the actual ip address in use for nfs
The check for sending to the gateway was not using the correct variable
for comparison, so it was reporting that packets are sent to the gateway
when they were not.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 2 Jul 2018 19:47:54 +0000 (14:47 -0500)]
sandbox: eth-raw: Add a SIMPLE_BUS to enumerate host interfaces
Ask the OS for each of its interfaces and for each one, bind a U-Boot
device and then probe it. This will allocate the priv data structure
that is then populated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Mon, 2 Jul 2018 19:47:46 +0000 (14:47 -0500)]
net: Only call halt on a driver that has been init'ed
With driver model, we were not checking if the state of the device was
marked as active before calling the halt function. Check that the device
is probed and also marked as active. This avoids the case where we were
calling halt on the first device in net_init() and the driver would
operate on bogus data structures causing problems. In this case, the
priv was all 0, so halt() would close STDIN.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Joe Hershberger [Tue, 3 Jul 2018 01:06:49 +0000 (20:06 -0500)]
sandbox: Don't disable ctrlc() on sandbox if in raw mode
In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.
In [1], Simon disabled this. His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.
Jeremy Gebben [Fri, 20 Jul 2018 22:00:36 +0000 (16:00 -0600)]
drivers/ddr/fsl: fix '__hwconfig without a buffer' messages
Pass an empty buffer instead of NULL if the hwconfig environment
variable isn't set.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Cc: Stefano Babic <sbabic@denx.de> Cc: York Sun <york.sun@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Fri, 8 Jun 2018 23:37:27 +0000 (16:37 -0700)]
armv8: ls1046ardb: Enable IFC for SPL build
Commit a52ff334c5b1 ("armv8: ls1046ardb: SPL size reduction") reduced
image size for SPL. IFC was disabled. If PPA is loaded in SPL, MMU is
enabled as a result. Removing IFC skips IFC region in the MMU table,
causing later failure in RAM version U-boot when accessing CPLD
through IFC. Only disable IFC if PPA is not enabled for SPL.
Make the code structure more general so that more socs can be
added easily and also remove speed limitation restriction.
Add the ls1012a sata support as well.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Michal Simek <michal.simek@xilinx.com>
(with and without CONFIG_OF_LIVE on zynqmp zcu102) Reviewed-by: York Sun <york.sun@nxp.com>
One ls1012a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
projects / u-boot.git / log
