Tom Rini [Sat, 26 Oct 2019 00:07:24 +0000 (20:07 -0400)]
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
Suman Anna [Thu, 17 Oct 2019 03:33:08 +0000 (09:03 +0530)]
arm: dts: k3-am65: Add R5F ranges in interconnect nodes
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 13:56:38 +0000 (19:26 +0530)]
armv7R: K3: j721e: Add support for triggering ddr init from SPL
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Kevin Scholz [Mon, 7 Oct 2019 13:56:36 +0000 (19:26 +0530)]
ram: k3-j721e: Add support for J721E DDR controller
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:27 +0000 (14:04 +0530)]
ram: k3-am654: Do not rely on default values for certain DDR register
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:25 +0000 (14:04 +0530)]
armv7r: dts: am654-base-board: Rename 1600MHz to 1600MTs in dtsi filename
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 08:22:17 +0000 (13:52 +0530)]
arm: K3: Clean and invalidate Linux Image before jumping to Linux
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
zynqmp:
- Clean firmware handing via drivers/firmware/
- DT/defconfig name alignments
- DT cleanups with using firmware based clock driver
- Some defconfig updates
- Add IIO ina226 DT description
- Tune zynqmp_psu_init_minimalize.sh script
- Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216
versal:
- Clean firmware handing via drivers/firmware/
- Add gpio support
- Enable DT overlay/USB/CLK/FPGA
- DT updates
- Tune mini configuration
dts: mtmips: add default pinctrl to eth nodes for all boards
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mt7628-eth: free rx descriptor on receiving failure
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
net: mt7628-eth: make phy link up detection optional via DT
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
net: mt7628-eth: remove hardcoded gpio settings and regmap-based phy reset
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628 part
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
spi: mt7621-spi: restore default register value after each xfer
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
spi: mt7621-spi: remove data cache and rewrite its xfer function
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clk: add clock driver for MediaTek MT76x8 platform
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
dts: mtmips: enable high-speed UART support for mt7628
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com> Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Ramon Fried [Mon, 10 Jun 2019 18:05:26 +0000 (21:05 +0300)]
MIPS: add compile time definition of L2 cache size
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
Ye Li [Thu, 24 Oct 2019 13:29:32 +0000 (10:29 -0300)]
ehci-mx6: Update EHCI driver to support OTG0 on i.MX7ULP
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
Igor Opaniuk [Thu, 10 Oct 2019 13:09:35 +0000 (16:09 +0300)]
usb: ehci-mx6: Fix bus enumeration for iMX7 SoCs
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Michal Simek [Mon, 21 Oct 2019 10:54:20 +0000 (12:54 +0200)]
common: command: Fix manual relocation for repeatable command
All platforms which are using MANUAL_RELOC are jumping back to origin
location when repeatable command is called. The reason is that cmd_rep link
is not updated properly. Issue can be reproduced by rewriting origin
U-Boot location through (for example) file download by tftp command.
Fixes: 80a48dd47e3b ("common: command: Rework the 'cmd is repeatable' logic") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 17 Oct 2019 11:16:56 +0000 (13:16 +0200)]
microblaze: Unify Linux bootm process
Record two bootstages and add "Starting kernel" message to have standard
handoff message between U-Boot and OS.
Also use debug() instead of #ifdef DEBUG to clean the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 15 Oct 2019 11:06:32 +0000 (13:06 +0200)]
ARM: zynq: Remove unused board_early_init_f()
board_early_init_f added by commit e6cc3b25d721
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e9812a ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 18 Jul 2018 07:25:43 +0000 (09:25 +0200)]
arm64: zynqmp: List lpd watchdog in dtsi
There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch increases SYS_MALLOC_F_LEN as the versal clock
driver needs to be probed before relocation itself inorder
to get required clocks before relocation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
projects / u-boot.git / log
