- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Simon Glass [Sun, 26 Apr 2020 15:12:58 +0000 (09:12 -0600)]
x86: Move coreboot-table detection into common code
To support detecting booting from coreboot, move the code which locates
the coreboot tables into a common place. Adjust the algorithm slightly to
use a word comparison instead of string, since it is faster.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the comments to 960KB] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:56 +0000 (09:12 -0600)]
pci: Avoid auto-config when chain loading
When U-Boot is not the first-stage bootloader we don't want to
re-configure the PCI devices, since this has already been done. Add a
check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:55 +0000 (09:12 -0600)]
x86: cpu: Skip init code when chain loading
When U-Boot is not the first-stage bootloader the interrupt and cache init
must be skipped, as well as init for various peripherals. Update the code
to add checks for this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:53 +0000 (09:12 -0600)]
x86: fsp: Allow skipping init code when chain loading
It is useful to be able to boot the same x86 image on a device with or
without a first-stage bootloader. For example, with chromebook_coral, it
is helpful for testing to be able to boot the same U-Boot (complete with
FSP) on bare metal and from coreboot. It allows checking of things like
CPU speed, comparing registers, ACPI tables and the like.
When U-Boot is not the first-stage bootloader much of this code is not
needed and can break booting. Add checks for this to the FSP code.
Rather than checking for the amount of available SDRAM, just use 1GB in
this situation, which should be safe. Using 2GB may run into a memory
hole on some SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:19:51 +0000 (09:19 -0600)]
acpi: Put table-setup code in its own function
We always write three basic tables to ACPI at the start. Move this into
its own function, along with acpi_fill_header(), so we can write a test
for this code.
Simon Glass [Sun, 26 Apr 2020 15:19:50 +0000 (09:19 -0600)]
acpi: Move acpi_add_table() to generic code
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Sun, 26 Apr 2020 15:19:47 +0000 (09:19 -0600)]
acpi: Convert part of acpi_table to use acpi_ctx
The current code uses an address but a pointer would result in fewer
casts. Also it repeats the alignment code in a lot of places so this would
be better done in a helper function.
Update write_acpi_tables() to make use of the new acpi_ctx structure,
adding a few helpers to clean things up.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Sun, 26 Apr 2020 15:19:45 +0000 (09:19 -0600)]
acpi: Add a binding for ACPI settings in the device tree
Devices need to report various identifiers in the ACPI tables. Rather than
hard-coding these in drivers it is typically better to put them in the
device tree.
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1046ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1046A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Introduce the QorIQ DPAA 1 Frame Manager nodes in the LS1043ARDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
LS1043A SoC. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Add the QorIQ DPAA Frame Manager v3 device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.
Biwen Li [Fri, 17 Apr 2020 09:37:01 +0000 (17:37 +0800)]
configs: ls1012afrwy: drop env qspi_bootcmd
Drop useless environment variable installer and qspi_bootcmd
for ls1012afrwy.
Only 2 MB nor flash in ls1012afrwy. So cannot get kernel(30 MB) from
the nor flash, then drop it.
Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Thu, 19 Mar 2020 08:48:25 +0000 (16:48 +0800)]
armv8: ls1028aqds: add lpuart dts support
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:46 +0000 (16:47 +0200)]
arm: dts: ls1088ardb: add DPMAC and PHY nodes
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (8 x
VSC8514, AQR105). Also, add phy-handles for the dpmacs to their
associated PHY.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:45 +0000 (16:47 +0200)]
arm: dts: ls2088ardb: add DPMAC and PHY nodes
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the external MDIO nodes and describe the PHYs (4 x AQR405
and 4 x CS4340). Also, add phy-handles for the dpmacs to their
associated PHY.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:44 +0000 (16:47 +0200)]
arm: dts: lx2160ardb: add DPMAC and PHY nodes
In order to maintain compatibility with the Linux DTS, the entire fsl-mc
node is added but instead of being probed by a dedicated bus driver it
will be a simple-mfd.
Also, annotate the EMDIO1 node and describe the 2 AR8035 RGMII PHYs and
the 2 AQR107 PHYs. Also, add phy-handles for the dpmacs to their
associated PHY.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:40 +0000 (16:47 +0200)]
board: ls2088ardb: transition to DM_ETH
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:39 +0000 (16:47 +0200)]
board: ls1088ardb: transition to DM_ETH
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:38 +0000 (16:47 +0200)]
drivers: net: fsl-mc: add support for CONFIG_DM_ETH
Make any adjustments necessary in order to support DPAA2 devices probed
using CONFIG_DM_ETH. While at it, fixup some styling issues aroung the
switch-case statement.
Ioana Ciornei [Wed, 18 Mar 2020 14:47:37 +0000 (16:47 +0200)]
drivers: net: ldpaa: add DTS based probing support
When CONFIG_DM_ETH is enabled DPAA2 network interfaces will now probe
based on DTS nodes with the "fsl,qoriq-mc-dpmac" compatible.
In this case, transform the ldpaa_eth driver into a UCLASS_ETH driver
and reuse the _open()/_tx()/_stop() functions already inplemented.
For the moment, the ldpaa_eth driver will support both configurations:
with or without CONFIG_DM_ETH enabled. Any 'struct eth_device' occurrence
now has a matching 'struct udevice' made mutually exclusive based on the
state of CONFIG_DM_ETH.
Marek Vasut [Sun, 5 Apr 2020 16:08:58 +0000 (18:08 +0200)]
ARM: dts: rmobile: Scrub unused DT nodes
Remove DT nodes which are not used by U-Boot, like audio and video in/out
nodes. This saves about 35 kiB on the resulting U-Boot binary without any
impact on functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Fri, 24 Apr 2020 16:30:45 +0000 (12:30 -0400)]
sunxi: Fix PHY regression on A20-OLinuXino-Lime2 and A20-Olimex-SOM-EVB
When moving the PHYLIB PHY drivers around in Kconfig we did not at the
same time perform a careful migration of the related drivers and
sub-options. This lead to the case where previously Kconfig-enabled
driver choices were now disabled on some platforms. Correct this by
enabling both the PHY driver and sub-option on the above referenced
platforms.
Fixes: af2cbfd6b982 ("drivers: net: Provide Kconfig menu for PHYLIB") Fixes: 8728c97eff5b ("configs: Re-sync") Reported-by: Dario <dario86@tutamail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
kbuild: SPL/TPL: generate separate asm-offsets.h for SPL and TPL
Currently generic-asm-offsets.h and asm-offsets.h are generated based
on U-Boot proper config options. The same asm-offsets headers are used
for building U-Boot SPL/TPL, which causes potential offset mismatch if
U-Boot proper has different config options from U-Boot SPL/TPL.
This commit adds:
spl/include/generated/(generic-)asm-offsets.h
tpl/include/generated/(generic-)asm-offsets.h
spl/include/generated/(generic-)asm-offsets.h is generated if
CONFIG_SPL=y, and included when building SPL.
tpl/include/generated/(generic-)asm-offsets.h is generated if
CONFIG_TPL=y, and included when building TPL.
They are created before Kbuild descends into SPL/TPL object directories
and builds $(obj)/dts/dt-platdata.o because $(obj)/dts/dt-platdata.c
includes a bunch of headers.
Prepend -I$(obj)/include to $(UBOOTINCLUDE) so (generic-)asm-offsets.h
is searched in {spl,tpl}/include/generated/.
Requested-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 5 Apr 2020 16:17:42 +0000 (18:17 +0200)]
ARM: rmobile: Unify Gen3 Salvator-X(S) and ULCB defconfigs
The r8a779{5,6,65}_salvator-x and r8a779{5,6,65}_ulcb_defconfig were
building the same target, except for the default DT. The default DT is
however only a detail, as the actual DT to be used to configure U-Boot
is detected automatically based on the CPU ID, hence the default DT is
not meaningful. Unify each three defconfigs per board to reduce the
duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Tue, 28 Apr 2020 14:09:16 +0000 (10:09 -0400)]
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
As the lower 16bit of the redistributor pending table is reserved
for describing the memory attributes, we must give a 64KB aligned
address to the GIC LPI initialization function.
Program the GIC redistributor tables only when succeeded to reserve memory
for them, otherwise kernel will lose the chance to program them using
allocated memory.
armv8: ls1046ardb: update the DIMM WRLVL_START value
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ.
Update DDR struct to set new WRLVL_START values so that the new DIMM
MTA18ADF2G72AZ get optimized and the old DIMM still works.
Alison Wang [Thu, 23 Apr 2020 14:37:34 +0000 (22:37 +0800)]
configs: ls1021a: Append CMA configuration to bootargs
The default reserved memory for CMA is high memory. If LPAE is enabled,
highmem pages are non-remapped and can not be used with
dma_alloc_coherent. Reserving low memory for CMA is needed for LS1021A.
This patch appends the related CMA configuration to bootargs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Patrick Delaunay [Mon, 27 Apr 2020 13:30:00 +0000 (15:30 +0200)]
usb: host: dwc2: force reset assert
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Mon, 27 Apr 2020 13:29:57 +0000 (15:29 +0200)]
dm: clk: add stub when CONFIG_CLK is deactivated
Add stub for functions clk_...() when CONFIG_CLK is deactivated.
This patch avoids compilation issues for driver using these API
without protection (#if CONFIG_IS_ENABLED(CLK))
For example, before this patch we have undefined reference to
`clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);
clk_release_bulk(&priv->clks);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Neil Armstrong [Tue, 21 Apr 2020 08:17:42 +0000 (10:17 +0200)]
usb: dwc3-meson-g12a: add power-on/off of the PHYs
Power on/off the PHYs to enable power to the USB ports, fixing USB support
on Khadas VIM3/VIM3L boards.
The G12A USB complex has at least 2 USB2 PHYs, but one is muxed between the
DWC2 and DWC3 controller and the other one directly connected to the DWC3
controller. The USB3+PCIe combo PHY is muxed between the DWC3 controller
and a DW-PCIE controller.
All PHYs are optional, but it's type (usb2/usb3) and position are important
to determine it's capabilities, thus they are stored in a fixed size
array and the phy-name determines it's position, it's position determining
it's type and functionnalities.
This is why we need to loop over the array to power on all the DT provided
PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Marek Vasut <marex@denx.de>
Tom Rini [Mon, 27 Apr 2020 21:50:35 +0000 (17:50 -0400)]
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Tom Rini [Mon, 27 Apr 2020 21:50:11 +0000 (17:50 -0400)]
Merge tag 'arc-more-fixes-for-2020.07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-arc
Here we introduce new development platfrom for ARC: HSDK 4xD.
That's pretty much the same base-board as in HSDK but with
very recent quad-core ARC HS47D in the ASIC.
Thus we try to re-use existing code as much as possible while
inevitably add some pieces needed for the new ASIC.
Also we drop selection of bounce buffers on AXS10x
as there's no use of them any longer.
projects / u-boot.git / log
