armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Tom Rini [Wed, 9 Dec 2020 16:36:41 +0000 (11:36 -0500)]
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 10:29:17 +0000 (11:29 +0100)]
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Manuel Reis [Wed, 25 Nov 2020 10:16:20 +0000 (10:16 +0000)]
add check for ignored CONFIG_ENV_EXT4_DEVICE_AND_PART definition
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
Pali Rohár [Wed, 25 Nov 2020 18:20:09 +0000 (19:20 +0100)]
arm: mvebu: Espressobin: Add support for emmc into dts file
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a960 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Reviewed-by: Stefan Roese <sr@denx.de>
Marcel Ziswiler [Thu, 22 Oct 2020 08:21:40 +0000 (11:21 +0300)]
imx8: allow overriding memory layout
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Igor Opaniuk [Thu, 22 Oct 2020 08:21:38 +0000 (11:21 +0300)]
board: toradex: add apalis-imx8x 2gb wb it v1.1a module support
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tim Harvey [Fri, 25 Sep 2020 15:08:35 +0000 (08:08 -0700)]
imx8m: fix cache setup for dynamic sdram size
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Max Krummenacher [Wed, 28 Oct 2020 09:58:11 +0000 (11:58 +0200)]
ARM: dts: imx8mm-verdin: follow changed pmic
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Haibo Chen [Tue, 3 Nov 2020 09:18:35 +0000 (17:18 +0800)]
mmc: fsl_esdhc_imx: optimize the timing setting
For imx usdhc/esdhc, once set the DDR_EN, enable the DDR mode, the
card clock will be divied by 2 automatically by the host. So need
to first config the DDR_EN correctly, then update the card clock.
This will make sure the actual card clock is as our expected.
IC also suggest config the DDR_EN firstly, then config the clock
divider.
For HS400/HS400ES mode, need to config the strobe dll, this need
to based on the correct target clock rate, so need to do this after
clock rate is update.
Commit f692b479f02d changed the VPD partition name from "vpd" to
"vpd@0". Fix the VPD reader code to use the new name, so that
the VPD code keeps working.
Fixes: f692b479f02d ("i2c: eeprom: Use reg property instead of offset and size") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Oliver Graute [Fri, 6 Nov 2020 08:09:30 +0000 (09:09 +0100)]
imx: ahab: fix compiler warnings in debug
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Oliver Graute [Fri, 6 Nov 2020 08:09:31 +0000 (09:09 +0100)]
imx: ahab: Fix compiler warnings in printf
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Patrick Delaunay [Thu, 18 Jun 2020 07:41:34 +0000 (09:41 +0200)]
configs: cei-tk1-som: remove CONFIG_ARMV7_PSCI in include file
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 1 Apr 2020 23:28:55 +0000 (00:28 +0100)]
arm: tegra: add options for BOOTENV_EFI_SET_FDTFILE_FALLBACK for tegra186
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Peter Robinson [Wed, 1 Apr 2020 23:28:54 +0000 (00:28 +0100)]
arm: tegra: define fdtfile option for distro boot
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
colibri_t30: fix spi1 and uart2/3 resp. uartb/c pinmuxing
Fix SPI1 and UART2/3 resp. UARTB/C pinmuxing.
Note: The former was illegally muxing multiple SoC balls onto the same
internal SoC signal which caused rather strange behaviour regarding
the RS232 serial transceiver ForceOFF# pins as available on Iris.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
apalis/colibri_t30: add comment about tristate and input vs. output pinmuxing
Add pinmuxing comment stating that TRISTATE means the output driver is
tri-stated and INPUT means the input driver is enabled vs. OUTPUT where
it is disabled.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
AKASHI Takahiro [Thu, 19 Nov 2020 00:37:19 +0000 (09:37 +0900)]
common: update: fix an "unused" warning against update_flash()
Since update_flash() is used only in update_tftp(), it should be
guarded with appropriate config options.
After the commit 3149e524fc1e, common/update.c will be built under
either CONFIG_UDATE_TFTP, CONFIG_DFU_TFTP or CONFIG_UPDATE_FIT.
Since CONFIG_UPDATE_FIT, hence fit_update(), doesn't rely on
update_flash(), the compiler may cause an "unused" warning if
CONFIG_UPDATE_FIT=y and CONFIG_UPDATE_TFTP=n and CONFIG_DFU_TFTP=n.
This is, for example, the case for sandbox defconfig where
EFI_CAPSULE_FIRMWARE_FIT is enabled for test purpose.
Fixes: 3149e524fc1e ("common: update: add a generic interface for FIT
image") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Simon Glass [Mon, 30 Nov 2020 00:07:05 +0000 (17:07 -0700)]
global_data: Fix comment for dm_driver_rt
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: a294ead8d25 ("dm: Use an allocated array for run-time device info") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Mon, 30 Nov 2020 00:07:04 +0000 (17:07 -0700)]
log: Fix comment for LOGC_BOOT
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: b73d61a5565 ("x86: zimage: Add a little more logging") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andy Shevchenko [Thu, 19 Nov 2020 19:26:20 +0000 (21:26 +0200)]
linux/compat.h: Remove debug() from spin_lock_irqsave()
It seems nobody tested the debug() option in spin_lock_irqsave().
Currently, when #define DEBUG, it spoils the compiler with
In file included from drivers/usb/dwc3/gadget.c:18:
drivers/usb/dwc3/gadget.c: In function ‘dwc3_gadget_set_selfpowered’:
include/log.h:235:4: warning: ‘flags’ is used uninitialized in this function [-Wuninitialized]
235 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
drivers/usb/dwc3/gadget.c:1347:17: note: ‘flags’ was declared here
1347 | unsigned long flags;
| ^~~~~
and so on...
Drop useless debug() call to make compiler happy.
Fixes: 0c06db598367 ("lib, linux: move linux specific defines to linux/compat.h") Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Mon, 23 Nov 2020 08:08:19 +0000 (09:08 +0100)]
binman: Remove additional backslash
The origin patch didn't have this change and it was caused by manual
resolution where additional backslash was added.
Fixes: 6723b4c6ca7b ("binman: Call helper function binman_set_rom_offset() to fill offset") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sun, 15 Nov 2020 20:22:53 +0000 (21:22 +0100)]
dm: core: Fix incorrect flag check
The test should be checking whether $flags are non-zero and $drv_flags
contain specific flags, however these two sets of flags are separate,
and the two tests should be logically ANDed, not bitwise ANDed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
sandbox: cros_ec: Basic support for EC_CMD_GET_NEXT_EVENT
Since commit 690079767803 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") the cros-ec-keyb driver has started using this
command, but the sandbox EC emulator does not recognize it and
continuously prints:
** Unknown EC command 0x67
This patch makes the sandbox driver send basic responses to the command,
but the response only supports keyboard scans for now.
The EC side of this command stores and returns events from a queue, and
returns -EC_RES_UNAVAILABLE when there are no new events. This should be
possible to implement by hooking into the SDL event queue (perhaps via
sandbox_sdl_poll_events). Implementing that is a bit harder to do since
the existing sandbox code is discarding pending keyboard events, then
reading the current keyboard state.
Since the EC emulator never explicitly fails to work on this command,
the fallback to the older command will not trigger and will not be
tested anymore.
Fixes: 690079767803 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT") Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
At present if CROSS_COMPILE contains a tilde, such as
~/.buildman-toolchains/gcc-7.3.0-nolibc/i386-linux/bin/i386-linux-gcc
then binman gives a confusing error:
Add a tool to update or insert an Octeon specific header into the U-Boot
image. This is needed e.g. for booting via SPI NOR, eMMC and NAND.
While working on this, move enum cvmx_board_types_enum and
cvmx_board_type_to_string() to cvmx-bootloader.h and remove the
unreferenced (unsupported) board definition.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 28 Oct 2020 14:10:02 +0000 (15:10 +0100)]
mips: octeon: bootoctlinux: Use gd->ram_size instead of ram_get_info()
Using ram_get_info() is complicated and does not work after relocation.
Now that gd->ram_size holds the full RAM size, let's use it instead and
remove the ram_get_size logic completely.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
projects / u-boot.git / log
