Fabien Parent [Thu, 17 Jan 2019 17:06:00 +0000 (18:06 +0100)]
mmc: mtk-sd: fix possible incomplete read ops
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Igor Opaniuk [Thu, 17 Jan 2019 14:37:40 +0000 (16:37 +0200)]
arm64: dt: poplar: add optee node
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Theil [Mon, 7 Jan 2019 09:25:52 +0000 (10:25 +0100)]
cmd: ximg: Invert check for fit image compression
The imgextract command runs a number of checks of
the specified fit. Where it checks for a load address
for compressed images the logic in the expression
is inverted as fit_image_check_comp returns 1 on
success and not 0.
Sean Nyekjær [Fri, 4 Jan 2019 11:37:24 +0000 (11:37 +0000)]
arm: stm32mp1: deploy spl in root folder
Deploy u-boot-spl.stm32 binary in u-boot root folder like
the rest of the boards.
This makes it more streamlined when building in Yocto, Buildroot etc..
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Chris Packham [Mon, 26 Nov 2018 08:00:29 +0000 (21:00 +1300)]
net: remove CONFIG_MCAST_TFTP
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Chris Packham [Mon, 26 Nov 2018 08:00:28 +0000 (21:00 +1300)]
net: move ether_crc to tsec driver
ether_crc was added to the core net code in commit 53a5c424bf86
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Carlo Caione [Wed, 16 Jan 2019 11:34:50 +0000 (11:34 +0000)]
net: phy: realtek: Add functions to read PHY's extended registers
According to the datasheet to access the extended registers we have to:
1. Write Register 31 Data = 0x0XYZ (Page 0xXYZ)
2. Read/Write the target Register Data
3. Write Register 31 Data = 0x0000 or 0xa42 (switch back to IEEE
Standard Registers)
Hook the missing functions so that we can use the `mdio rx/wx` command to
easily access the extended registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For KSZ9021, all skew register fields are 4-bit wide.
For KSZ9031, the clock skew register fields are 5-bit wide.
The common code in ksz90x1_of_config_group calculating the combined
register value checks if the requested value is above the maximum
and uses this maximum if so. The calculation of this maximum uses
the register width, but the check itself does not. It uses a hardcoded
value of 0xf, which is too low in case of the 5-bit clock (0x1f).
This detail was probably lost during driver unification.
Effect (only for KSZ9031 clock skews): For values greater 900 (== 0ps),
this silently results in 1860 (== +960ps) instead of the requested one.
Fix the check by using the bit width instead of hardcoded value(s).
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thomas RIENOESSL [Wed, 21 Nov 2018 14:56:07 +0000 (15:56 +0100)]
net: explicitly assign errno to return code in case of network failure
When dealing with two ethernet ports and having "netretry" set
to "once", it could occur that the connection (e.g. an ARP
request) failed, hence the status of the netloop was
"NETLOOP_FAIL". Due to the setting of "netretry", the network
logic would then switch to the other network interface,
assigning "ret" with the return value of "net_start_again()".
If this call succeeded we would return 0 (i.e. success) to
the caller when in reality the network action failed.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Baruch Siach [Wed, 21 Nov 2018 11:05:34 +0000 (13:05 +0200)]
net: mvpp2: mdio device per port
Current code forces all ports on a given Ethernet device to use the same
mdio device. In practice different ports might be wired to separate mdio
devices. Move the mdio device from the container struct mvpp2 to the per
port struct mvpp2_port.
Cc: Ken Ma <make@marvell.com> Cc: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Baruch Siach [Wed, 21 Nov 2018 11:05:33 +0000 (13:05 +0200)]
net: mvpp2: fix lookup of mdio registers base address
Current mdio base lookup code relies on a 'reg' property at the upper CP
node. There is no 'reg' property there in current DT files of Armada
CP110. Use ofnode_get_addr() instead since it provides proper DT address
translation.
Cc: Ken Ma <make@marvell.com> Cc: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Short frames are padded to the minimum allowed size of 60 bytes.
However, the designware driver sends old data in these padding bytes.
It is common practice to zero out these padding bytes ro prevent
leaking memory contents to other hosts.
Fix the padding code to zero out the padded bytes at the end.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The designware driver has a bug in setting the tx length into the dma
descriptor: it always or's the length into the descriptor without
zeroing out the length mask before.
This results in occasional packets being transmitted with a length
greater than they should be (trailer). Due to the nature of Ethernet
allowing such a trailer, most packets seem to be parsed fine by remote
hosts, which is probably why this hasn't been noticed.
Fix this by correctly clearing the size mask before setting the new
length.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Pankaj Bansal [Fri, 16 Nov 2018 06:26:18 +0000 (06:26 +0000)]
net: phy: Add clause 45 identifier to phy_device
The phy devices can be accessed via clause 22 or via clause 45.
This information can be deduced when we read phy id. if the phy id
is read without giving any MDIO Manageable Device Address (MMD), then
it conforms to clause 22. otherwise it conforms to clause 45.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mike Looijmans [Fri, 18 Jan 2019 08:02:48 +0000 (09:02 +0100)]
board: topic-miamiplus: Run IO PLL at 1000 MHz
The miamiplus can use GEM0 through MIO pins, which requires a 125 MHz TX
clock to be generated. With the IO PLL at 1200 MHz this isn't possible, so
change it to run at 1000 and adjust the divisors accordingly. Also set the
GEM0 clock source to MIO instead of EMIO.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Looijmans [Fri, 18 Jan 2019 08:02:47 +0000 (09:02 +0100)]
topic-miamiplus: Run CPU at 800MHz for speedgrade-2
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 18 Jan 2019 09:43:39 +0000 (10:43 +0100)]
i2c: cdns: Convert to livetree function
Update cadence i2c driver to support livetree
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695afa794ac018a09e79a48120d322b60d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables CONFIG_REMAKE_ELF for Zynq platform
so that it generates u-boot.elf from binary which works
for all Zynq boards with OF_SEPARATE option enabled.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 16 Jan 2019 11:14:00 +0000 (12:14 +0100)]
arm64: zynqmp: Align u-boot-spl.bin for boot.bin creation
Bootrom is not capable to work with non align bootloader partition
that's why it is necessary to align it before boot.bin creation.
The patch is creating new spl/u-boot-spl-align.bin which is used only
for boot.bin.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bootrom is not capable to work with non aligned bootloader sizes.
SPL with OF_SEPARATE generates non-align images quite often that's
why this change is required before OF_SEPARATE enableding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 15 Jan 2019 09:45:41 +0000 (10:45 +0100)]
arm64: zynqmp: Enable ISSI flash for some platforms
Enable ISSI flash for platforms. Xilinx reference boards are also used
internally with different flash part to increase coverage that's why
enable also ISSI parts for all these boards even if that board is
released only with one part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Fix mmc node names to be in sync with kernel
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stefan Theil [Mon, 17 Dec 2018 08:12:30 +0000 (09:12 +0100)]
zynq-gem: Use appropriate cache flush/invalidate for RX and TX
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Dec 2018 08:41:12 +0000 (09:41 +0100)]
arm64: zynqmp: Do not protect zynqmp_pmufw_version()
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 5 Dec 2018 11:40:55 +0000 (12:40 +0100)]
mmc: zynq: Remove unused pwrseq variable
This variable was incorrectly added by:
"mmc: zynq_sdhci: Add support for SD3.0"
(sha1: d1f4e39d58db32a4fd1a1b4085e0ede498bd773f)
which had nothing to do with MMC power sequence provider.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michael Tretter [Mon, 3 Dec 2018 15:37:53 +0000 (16:37 +0100)]
tools: zynqmpimage: round up partition size
The FSBL copies "Total Partition Word Length" * 4 bytes from the boot.bin,
which implies that the partition size is 4 byte aligned. When writing the
partition, mkimage calculates "Total Partition Word Length" by dividing
the size by 4. This implicitly cuts unaligned bytes at the end of the
added binary.
Instead of rounding down, the size must be round up to 4 bytes and the
binary padded accordingly.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 23 Jan 2019 22:24:31 +0000 (17:24 -0500)]
Merge tag 'mips-pull-2019-01-23' of git://git.denx.de/u-boot-mips
- MIPS: mscc: ocelot: add ethernet switch and network support
- MIPS: mscc: add support for ServalT SoC family
- MIPS: mscc: add support for Serval SoC family
-msingle-pic-base is a new gcc(from 4.6) option for ppc and
it reduces the size of my u-boot with about 4-5 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
e5500 core:
size u-boot.bef
text data bss dec hex filename
473043 23772 307104 803919 c444f u-boot.bef
size u-boot.aft
text data bss dec hex filename
453195 23772 307104 784071 bf6c7 u-boot.aft
e500 core:
size u-boot.bef
text data bss dec hex filename
292998 17868 24968 335834 51fda u-boot.bef
size u-boot.aft
text data bss dec hex filename
288002 17868 24968 330838 50c56 u-boot.aft
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Reviewed-by: York Sun <york.sun@nxp.com>
ftsdc010_mci's compatible has been modified as
"andestech,atfsdc010" for RISC-V synchronization.
But ae3xx.dts and ag101p.dts which are used for
nds32 adp-ae3xx and adp-ag101p platforms did not
be modified correctly at that time. It will cause
mmc detection failure. Fix it here.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
Tom Rini [Mon, 21 Jan 2019 16:59:21 +0000 (11:59 -0500)]
Merge git://git.denx.de/u-boot-marvell
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
[Mailing List Thread]
https://lists.denx.de/pipermail/u-boot/2018-December/350666.html
Fixes: 5541543f ("configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment")
[trini: Make the migration be size neutral and possibly not fix the
above in all cases] Reported-by: Daniel Evans <photonthunder@gmail.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Chris Packham [Thu, 10 Jan 2019 08:01:00 +0000 (21:01 +1300)]
ARM: mvebu: add support for Allied Telesis x530
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Wed, 2 Jan 2019 16:26:42 +0000 (18:26 +0200)]
board: mvebu: drop unused ETH_PHY macro definitions
These macros are not used anywhere in the boards code.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
An NVME drive may be installed on the MACCHIATObin board using the PCIe
slot or on the Clearfog Pro using mini a PCI-e slot. With the configuration
change it becomes usable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log
