Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Fri, 30 Jul 2021 03:02:43 +0000 (20:02 -0700)]
arm: kirkwood: GoFlex Home: Use Ethernet PHY name and address from device tree
In DM Ethernet, the old "egiga0" name is no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
- new SOC: add support for imx8ulp
- Toradex fixes for colibri (vf / imx6 / imx7 / imx8x)
- convert to DM for mx28evk
- Fixes for Gateworks ventana boards
Peng Fan [Sat, 7 Aug 2021 08:01:13 +0000 (16:01 +0800)]
arm: imx: add i.MX8ULP EVK support
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Ye Li [Sat, 7 Aug 2021 08:01:07 +0000 (16:01 +0800)]
imx8ulp: Use DGO_GP5 to get boot config
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Peng Fan [Sat, 7 Aug 2021 08:00:58 +0000 (16:00 +0800)]
arm: imx8ulp: release trdc and assign lpav from RTD to APD
Rlease LPAV from RTD to APD
Release gpu2D/3D to APD
Set TRDC MBC2 MEM1 for iomuxc0 access
Since upower depends AP/M33 SW to configure IOMUX for its PMIC i2c
and MODE pins. we have to open iomuxc0 access for A35 core (domain 7)
in single boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
Ye Li [Sat, 7 Aug 2021 08:00:55 +0000 (16:00 +0800)]
arm: imx8ulp: release and configure XRDC at early phase
Since S400 will set the memory of SPL image to R/X. We can't write
to any data in SPL image.
1. Set the parameters save/restore only for u-boot, not for SPL. to
avoid write data.
2. Not use MU DM driver but directly call MU API to send release XRDC
to S400 at early phase.
3. Configure the SPL image memory of SRAM2 to writable (R/W/X)
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Sat, 7 Aug 2021 08:00:48 +0000 (16:00 +0800)]
arm: imx8ulp: Enable full L2 cache in SPL
SRAM2 is half L2 cache and default to SRAM after system boot.
To enable the full l2 cache (512KB), it needs to reset A35 to make
the change happen.
So re-implement the jump entry function in SPL:
1. configure the core0 reset vector to entry (ATF)
2. enable the L2 full cache
3. reset A35
So when core0 up, it runs into ATF. And we have 512KB L2 cache working.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Sat, 7 Aug 2021 08:00:35 +0000 (16:00 +0800)]
arm: imx: basic i.MX8ULP support
Add basic i.MX8ULP support
For the MMU part, Using a simple way the calculate the MMU size to avoid
default heavy calcaulation. And align address and size in the table
settings to 2MB or 4GB as much as possible. So we can reduce the 4K page
allocations in MMU table which will spends much time in create the
page table
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Select CONFIG_IMX_HAB so that the "hab_status" command
becomes available, which is useful for checking if the
chip has been correctly setup to run in secure boot mode.
Tim Harvey [Tue, 27 Jul 2021 22:19:41 +0000 (15:19 -0700)]
board: gateworks: venice: add imx8mm-gw7902 support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Tim Harvey [Tue, 27 Jul 2021 22:19:39 +0000 (15:19 -0700)]
board: gateworks: venice: add board model/serial# to env
Add board model/serial# strings to env. Move the creation of the strings
to gsc_read() and the display of the info into gsc_info() so they are
available to U-Boot proper.
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.
Tim Harvey [Tue, 27 Jul 2021 22:19:34 +0000 (15:19 -0700)]
arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
The intention of commit d714a75fd4dc ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.
Fix it by using the correct CONFIG_IMX_HAB symbol.
Tim Harvey [Sat, 24 Jul 2021 17:40:46 +0000 (10:40 -0700)]
imx: ventana: add support for GW54xx-G revision
The GW54xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Tim Harvey [Sat, 24 Jul 2021 17:40:45 +0000 (10:40 -0700)]
imx: ventana: add support for GW53xx-G revision
The GW53xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Tim Harvey [Sat, 24 Jul 2021 17:40:44 +0000 (10:40 -0700)]
imx: ventana: add GW5913 support
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- Digital I/O connector (I2C/GPIO/UART)
- u-blox Zoe-M8Q GPS
- 1x RJ45 GbE
- 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:43 +0000 (10:40 -0700)]
imx: ventana: add GW5912 support
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- CAN/RS485 connector
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- 1x FEC GbE RJ45 with 802.3at Active PoE
- 1x PCI GbE RJ45 with Passive PoE
- 5x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
- Aux power input with wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:42 +0000 (10:40 -0700)]
imx: ventana: add GW5910 support
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
- On-board brcmfmac WiFi and BT module
- RGMII RJ45 GbE
- 1x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Tim Harvey [Sat, 24 Jul 2021 17:40:36 +0000 (10:40 -0700)]
imx: ventana: fix UMS support
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.
U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.
Fixes 72c46327f03f: ("imx: ventana: enable dm support for USB")
This patch fixes the following compiler warning:
=============
board/toradex/colibri_vf/colibri_vf.c: In function 'ft_board_setup':
board/toradex/colibri_vf/colibri_vf.c:436:6: warning: unused variable 'ret' [-Wunused-variable]
=============
Stefan Agner [Fri, 23 Jul 2021 06:39:46 +0000 (09:39 +0300)]
board: toradex: make USB PID from config block optional
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Stefan Agner [Fri, 23 Jul 2021 06:39:45 +0000 (09:39 +0300)]
board: colibri_imx7: use SDP if USB serial downloader has been used
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Do not pass the console baudrate to the 'console' variable
to avoid the baudrate being passed twice when extlinux.conf
contains the standard: console=${console},${baudrate} format.
Simon Glass [Mon, 2 Aug 2021 13:37:54 +0000 (07:37 -0600)]
dtoc: Correct the intarray-widening test case
This case was intended to check that widening an int array with an int
does nothing. Fix it.
Reported-by: Walter Lozano <walter.lozano@collabora.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
Simon Glass [Sun, 1 Aug 2021 18:05:23 +0000 (12:05 -0600)]
dm: core: Don't allow uclass use before ready
At present it is possible to call uclass_get() before driver model is
inited. In fact this happens on x86 boards which use Intel FSPv1, since
mrccache_get_region() tries to get the SPI flash device very early
during init.
This has always been undefined behaviour. Previously it generally worked,
i.e. returned an error code without crashing, because gd->uclass_root_s
is zeroed and the uclass can be added despite driver model not being
ready, due to the way lists are implemented. With the change to use a
gd->uclass_root pointer, this no-longer works. For example, it causes a
hang on minnowmax.
Fix this by adding a check that driver model is ready when uclass_get() is
called. This function is called in the process of locating any device, so
it is a good place to add the check.
This fixes booting on minnowmax.
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 8a715530bb1 ("dm: core: Allow the uclass list to move")
While the goal is valid and there is surely unused memory in that area,
we also have a lot of crucial things still located at the top-of-memory
while running lmb_alloc_base. Such things are the page table (tlb_addr),
relocated U-Boot and the active stack. Possibly more. So this patch was
premature, we will need relocations of those things first if we want to
use the range.
Fixes booting on the IOT2050, but likely also on other boards. It got
stuck on relocating the FDT - over the relocated U-Boot code.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Marek Vasut [Sun, 13 Jun 2021 20:41:09 +0000 (22:41 +0200)]
ARM: renesas: Set CONFIG_SYS_TEXT_BASE=0x0 on R-Car Gen3
Since R-Car Gen3 already enables position independent build, also set
CONFIG_SYS_TEXT_BASE=0x0 to finalize the switch. This is possible since 534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_SYS_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
projects / u-boot.git / log
