Andre Przywara [Tue, 27 Jul 2021 14:47:50 +0000 (15:47 +0100)]
video: Hitachi panel: Drop bogus dependency on CONFIG_VIDEO
The Hitachi tx18d42vm LCD panel driver is really just initialising the
device, using bitbanged SPI, during operation there is nothing to do.
This makes the driver self contained, so drop the bogus dependency on
the legacy CONFIG_VIDEO.
This avoids the warning when building Chuwi_V7_CW0825_defconfig, since
we switched to DM_VIDEO recently.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Stephan Gerhold [Fri, 2 Jul 2021 17:21:56 +0000 (19:21 +0200)]
video: Add simple driver for ST-Ericsson MCDE with pre-configured display
The U-Boot port for ST-Ericsson Ux500 is currently only used on the
"stemmy" board, where U-Boot runs after firmware that already sets up
a boot splash screen. This means that the display is already on
and we can just continue using it for U-Boot.
Add a simple driver that simplifies this by reading the display
configuration (e.g. screen size, bpp) from the hardware registers.
It also checks the configured "source synchronization" - for some
displays (usually DSI command mode displays) we need to explicitly
trigger a software sync. This is done through the video_sync()
callback that triggers the sync and wait for completion.
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
Samuel Holland [Mon, 19 Apr 2021 03:21:41 +0000 (22:21 -0500)]
sunxi: A23/A33/H3: Move sun8i secure monitor to SRAM A2
So far for the H3, A23, and A33 SoCs, we use DRAM to hold the secure
monitor code (providing PSCI runtime services). And while those SoCs do
not have the secure SRAM B like older SoCs, there is enough (secure)
SRAM A2 to put the monitor code and data in there instead.
Follow the design of 64-bit SoCs and use the first part for the monitor,
and the last 16 KiB for the SCP firmware. With this change, the monitor
no longer needs to reserve a region in DRAM.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: amend commit message, fix R40 and V3s build] Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 19 Apr 2021 03:16:21 +0000 (22:16 -0500)]
sunxi: Select environment MMC based on boot device
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
serial: a37xx: Do not call get_ref_clk() in _debug_uart_init()
Static inline function _debug_uart_init() should avoid calling external
(non-inline) functions. Therefore do not call get_ref_clk() in
_debug_uart_init() and reimplement its functionality without external
function calls.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Mon, 26 Jul 2021 06:01:19 +0000 (23:01 -0700)]
arm: kirkwood: Dreamplug: Use Ethernet PHY name and address from device tree
In DM Ethernet, the old "egiga0" and 'egiga1" names are no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address for each port from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
tools: kwbimage: Remove v1 kwbimage SPL padding to CONFIG_SYS_U_BOOT_OFFS bytes
This padding depends on board config file and therefore it makes the
mkimage binary tool board specific, which is not correct. One cannot use
mkimage tool built as a result for board A to generate images for board
B, even if both A and B are on the same platform.
This CONFIG_SYS_U_BOOT_OFFS padding was needed when kwbimage v1 contained
SPL code which loaded U-Boot proper based on CONFIG_SYS_U_BOOT_OFFS,
instead of reading correct offset from kwbimage header.
Now that SPL code parses kwbimage header and deterinate correct offset,
there is no need for this CONFIG_SYS_U_BOOT_OFFS padding anymore.
By removing it we also reduce the size of SPL code and therefore also
decrease the final size of v1 kwbimage. This means there is more space
for U-Boot proper binary.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: Remove legacy U-Boot header from kwbimage v1 files
The SPL code now already parses kwbimage v1 headers where all necessary
information about how to load and execute U-Boot proper is present. The
legacy 64-byte U-Boot header is not used anymore.
Remove this 64-byte header by putting u-boot.bin binary (instead of
u-boot.img) into kwbimage v1 and let SPL code or BootROM to load U-Boot
directly at its execution address.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
SPL: Add support for parsing board / BootROM specific image types
Platform specific BootROM may use its own image type for loading SPL or
U-Boot proper. In some cases it makes sense to not use BootROM supplied
code for booting U-Boot proper but rather to use U-Boot SPL for this,
e.g. when U-Boot SPL can load U-Boot proper faster than BootROM. In this
case it is required for platform board code to parse and load U-Boot in
BootROM specific image type.
This change adds support for parsing platform / board / BootROM specific
image types via weak function spl_parse_board_header() which is called
before marking boot image as a raw.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
SPL: Add support for specifying offset between header and image
Some image types (e.g. kwbimage v1) store the offset to SPL binary and
offset to U-Boot proper binary in their headers. To avoid reading SPL
binary when loading U-Boot proper, add support for specifying offset in
struct spl_image_info, which defines the offset from the beginning of
the header and the beginning of the executable data.
Initial support is added only for SPI, MMC and SATA code. We can extend
it later if needed.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: Use U-Boot's SPL BootROM framework for booting from NAND/UART
Current code uses hack in board_init_f() which calls return_to_bootrom()
to skip U-Boot SPL code and return back to BootROM to load U-Boot via
UART or from NAND.
This change migrates that hack from the board_init_f() function and
changes it to return BOOT_DEVICE_BOOTROM instead of returning to BootROM
directly, so that U-Boot's SPL framework is used for returning to
BootROM.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
arm: mvebu: Implement return_to_bootrom() via U-Boot's SPL framework
U-Boot's SPL framework already has an API for loading U-Boot via
BootROM.
Implement the function board_return_to_bootrom() for mvebu SPL code.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
arm: mvebu: Mark return_to_bootrom() as a noreturn function
This function does not return, so add the appropriate compiler flag.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Register r0 should be set to return value 0x0 - NO_ERR.
Set r0 with return value after all registers are restored from the
stack, so that the return value is always correct.
Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 944c7a317675 ("arm: mvebu: Add option to use UART xmodem protocol via kwboot") Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Too small invalid headers may cause kwboot to crash.
Check for header size of v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Add missing curly brackets for this else statement.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwboot: Print trailing newline after terminal is terminated
Print trailing newline as the last printed byte can be something
different.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Call tcsetattr() only if the file descriptor is valid. It may be
invalidated by previous lines (if it is not a tty descriptor).
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwboot: Fix wrong parameter passed to read()
The 'buf' variable is a pointer and '_buf' is the array itself.
Therefore we should pass sizeof(_buf) instead of sizeof(buf) to read().
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: dumpimage: Show error message when trying to extract data from kwbimage
There is no code for extracting data from kwbimage, so show an error
message when user tries this via e.g. dumpimage call:
./tools/dumpimage -T kwbimage -o /tmp/out u-boot-spl.kwb
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
tools: kwbimage: Do not hide usage of secure header under CONFIG_ARMADA_38X
The mkimage host tool can be used to generate kwbimage v1 image with
secure header on host system for A38x plaform also when U-Boot is being
compiled for different platform. So there is no reason to not allow
compiling of mkimage/kwbimage with secure header support for e.g. x86-64
host.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Add support for a new DATA_DELAY command
This command is supported only by v1 images and specifies a milliseconds
delay after executing some set of DATA commands. The special string value
SDRAM_SETUP instructs BootROM to setup SDRAM controller instead of
executing delay. SDRAM_SETUP may be specified only once and after the
last DATA command.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Add support for DATA command also for v1 images
The DATA command is already supported by mkimage for v0 images, but not
for v1 images.
BootROM code which executes v1 images also supports DATA command via an
optional extended v1 header OPT_HDR_V1_REGISTER_TYPE.
Implement support for DATA command for v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Chris Packham <judge.packham@gmail.com>
The PAYLOAD keyword does nothing. No code is using it and both mkimage
and kwbimage completely ignore it. It looks like a relict from the past.
The payload image itself can be specified only via -d parameter to
mkimage.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Add support for more BINARY headers
The kwbimage v1 format supports multiple BINARY executable headers.
Add support for it into mkimage/kwbimage tool.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Fix calculating size of binary header
Binary header consist of:
* 1 byte for header type
* 3 bytes for header size
* 1 byte for number of arguments
* 3 reserved bytes
* N*4 bytes for arguments
* M bytes (aligned to 4 bytes) for executable data
* 1 byte for information about next header
* 3 reserved bytes
The first four bytes are specified as
sizeof(struct opt_hdr_v1)
and the remaining bytes as
ALIGN(s.st_size, 4) + (binarye->binary.nargs + 2) * sizeof(uint32_t)
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
tools: kwbimage: Use -a parameter (load address) for v1 images
The data part of v1 kwbimage currently contains U-Boot binary prepended
by 64 bytes long Legacy U-Boot image header. This means that the load
address is currently substracted by 64 bytes to ensure that U-Boot's
entry point is at specified execution address.
As mkimage has already separate arguments for load (-a) and execution
(-e) address, there is no need to derive fixed load address from
execution address.
Therefore remove this load address hack from the kwbimage tool and
support generating v1 kwbimage with arbitrary addresses for load and
execution.
Finally, calculate correct load address by caller for mkimage tool in
Makefile. File u-boot-spl.kwb is always a v1 kwbimage and it is the only
v1 kwbimage which U-Boot's build system generates.
Remove also useless overwriting of destaddr for /binary.0 to the value
which is already set on previous lines.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Marek Behún [Fri, 23 Jul 2021 09:14:05 +0000 (11:14 +0200)]
tools: kwbimage: Cosmetic fix - remove redundant space character
Remove this space, since the constants are indented by tabs.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Print size of binary header in kwbimage_print_header()
The binary header in kwbimage contains executable SPL code.
Print information about this binary header and not only information
about it's data part.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Validate data checksum of v1 images
The data part of v1 images contains 32-bit checksum after the data.
Validate whether this checksum is correct.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Validate extended headers of v1 images
Add basic checks for extended headers of v1 images.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Fix check for v0 extended header checksum
Extended header checksum for v0 image is present only in the case when
extended header is present. Skip checksum validation if extended header
is not present.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Don't crash when binary file name does not contain '/'
In the case when the file name is specified relative to the current
working directory, it does not contain '/' character and strrchr()
returns NULL.
The following strcmp() function then crashes on NULL pointer
dereference.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Fix generation of SATA, SDIO and PCIe images
SATA and SDIO images must be aligned to sector size (which in most cases
is 512 bytes) and Source Address in main header is stored in number of
sectors from the beginning of the drive. SATA image must be stored at
sector 1 and SDIO image at sector 0. Source Address for PCIe image is
not used and must be set to 0xFFFFFFFF.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Marek Behún [Fri, 23 Jul 2021 09:13:58 +0000 (11:13 +0200)]
tools: kwbimage: Add constant for SDIO bootfrom
Add constant for SDIO value of the bootfrom header field.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Align SPI and NAND images to 256 bytes
Writing into SPI NOR and NAND memory can be done only in 256 bytes long
blocks. Align final image size so that when it is burned into SPI NOR or
NAND memory via U-Boot's commands (sf or mtd), we can use the $filesize
variable directly as the length argument.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Simplify aligning and calculating checksum
The return value of kwbimage_generate() is used for aligning the data
part of kwbimage. Use it for calculating proper 4 byte alignment as is
required by BootROM and also use it for allocating additional 4 bytes
for the 32-bit data checksum.
This simplifies the alignment code to be only at one place (in function
kwbimage_generate) and also simplifies setting checksum as it can be
directly updated in memory.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
tools: kwbimage: Fix compilation without CONFIG_SYS_U_BOOT_OFFS
The CONFIG_SYS_U_BOOT_OFFS option may be defined as empty string.
In this case it causes compilation error:
tools/kwbimage.c: In function ‘image_headersz_v1’:
tools/kwbimage.c:1002:39: error: expected expression before ‘)’ token
if (headersz > CONFIG_SYS_U_BOOT_OFFS) {
^
tools/kwbimage.c:1006:41: error: expected expression before ‘)’ token
(int)headersz, CONFIG_SYS_U_BOOT_OFFS);
^
tools/kwbimage.c:1011:35: error: expected expression before ‘;’ token
headersz = CONFIG_SYS_U_BOOT_OFFS;
^
make[1]: *** [scripts/Makefile.host:112: tools/kwbimage.o] Error 1
make: *** [Makefile:1822: tools] Error 2
Check whether the value of CONFIG_SYS_U_BOOT_OFFS is really set.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com>
Suman Anna [Mon, 26 Jul 2021 23:22:48 +0000 (18:22 -0500)]
board: ti: k2g: Program PadConfig_202 before locking RSTMUX8
The PADCONFIG_202 register (0x02621328) is affected by the locking
of the RSTMUX8 register (0x02620328), and so cannot be configured
in kernel. This has been confirmed as a hardware bug and affects
all K2G SoCs.
Setup the pinmux for this pin before locking the RSTMUX8 register
to allow the ICSS1 PRU1 Ethernet PHY port to work properly. The
workaround was added only for the K2G-ICE board to configure the
pins needed for the PRUSS Ethernet usecase.
mkimage: use environment variable MKIMAGE_SIGN_PIN to set pin for OpenSSL Engine
This patch adds the possibility to pass the PIN the OpenSSL Engine
used during signing via the environment variable MKIMAGE_SIGN_PIN.
This follows the approach used during kernel module
signing ("KBUILD_SIGN_PIN") or UBIFS image
signing ("MKIMAGE_SIGN_PIN").
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Patrick Delaunay [Wed, 21 Jul 2021 07:56:07 +0000 (09:56 +0200)]
build: remove the variable NM in gen_ll_addressable_symbols.sh
With LTO activated, the buildman tools failed with an error on my
configuration (Ubuntu 20.04, stm32mp15_trusted_defconfig) with the error:
../arm-linux-gnueabi/bin/nm:
scripts/gen_ll_addressable_symbols.sh: file format not recognized
It seems the shell variable initialization NM=$(NM) is not correctly
interpreted when shell is started in the Makefile, but I have not this
issue when I compile the same target without buildman.
I don't found the root reason of the problem but I solve it by
providing $(NM) as script parameter instead using a shell variable.
At early U-Boot stage, before relocation, MMU is not yet configured
and disabled. DDR may not be configured with the correct memory
attributes (can be configured in MT_DEVICE instead of MT_MEMORY).
In this case, usage of memcpy_{from, to}io() may leads to synchronous
abort in AARCH64 in case the normal memory address is not 64Bits aligned.
To avoid such situation, forbid usage of normal memory cast to (u64 *) in
case MMU is not enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: mark.kettenis@xs4all.nl Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Simon Glass [Sun, 11 Jul 2021 03:14:35 +0000 (21:14 -0600)]
i2c: Create a new Kconfig for I2C
At present we have CONFIG_SPL_I2C but not CONFIG_I2C. The reason
CONFIG_I2C is not strictly necessary is that:
a) We have CONFIG_SYS_I2C_LEGACY and CONFIG_DM_I2C for the two possible
i2c stacks
b) In U-Boot proper, we always build drivers/i2c/ regardless of the
options
Still, it is better to have CONFIG_I2C - it makes U-Boot proper similar to
SPL/TPL, so we can (in a future commit) simplify the Makefile rules.
Enable it by default, since as above, we have separate options
(SYS_I2C_LEGACY and DM_I2C) to control whether it is 'really' enabled.
Once we have migrated I2C to driver model, we can drop SYS_I2C_LEGACY and
make DM_I2C become I2C. For now, this lets us simplify the Makefile rules.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Sun, 11 Jul 2021 03:14:33 +0000 (21:14 -0600)]
i2c: Fix the migration warning
While there is a CONFIG_I2C it does not really mean anything and is
defined by only a few dozen boards. This should key off
CONFIG_SYS_I2C_LEGACY instead.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Sun, 11 Jul 2021 03:14:32 +0000 (21:14 -0600)]
i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACY
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
Simon Glass [Fri, 2 Jul 2021 18:36:16 +0000 (12:36 -0600)]
Allow efi_loader header to be included always
It is bad practice to put function declarations behind an #ifdef since
it makes it impossible to use IS_ENABLED() in the C code. The main reason
for doing this is when an empty static inline function is desired when
the feature is disabled.
To this end, this header provides two different versions of various
functions and macros. Collect them together in one place for clarity.
Allow all the rest of the header to be included, regardless of the
setting of EFI_LOADER.
With the inclusion of blk.h the 'struct blk_desc' declaration is
unnecessary. Drop it while we are here.
Simon Glass [Fri, 2 Jul 2021 18:36:14 +0000 (12:36 -0600)]
disk: Tidy up #ifdefs in part_efi
This file does not correctly handle the various cases, sometimes
producing warnings about partition_basic_data_guid being defined but not
used. Fix it.
There was some discussion about adjusting Kconfig or making
HAVE_BLOCK_DEVICE a prerequisite for PARTITIONS, but apparently this is
not feasible. Such changes can be undertaken separate from the goal of
this series.
Simon Glass [Fri, 2 Jul 2021 18:36:13 +0000 (12:36 -0600)]
Makefile: Drop include/asm directory as well as symlink
At present when using 'make mrproper' on an out-of-tree build, a warning
is shown about include/asm being a directory. With old versions of U-Boot
it is a file, but more recently it has become a directory.
Remove this directory first, since that covers both cases.
Roland Gaudig [Fri, 23 Jul 2021 12:29:21 +0000 (12:29 +0000)]
cmd: setexpr: add format string handling
Add format string handling operator to the setexpr command.
It allows to use C or Bash like format string expressions to be
evaluated with the result being stored inside the environment variable
name.
setexpr <name> fmt <format> [value]...
The following example
setexpr foo fmt "%d, 0x%x" 0x100 ff
will result in $foo being set to "256, 0xff".
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Roland Gaudig [Fri, 23 Jul 2021 12:29:20 +0000 (12:29 +0000)]
cmd: printf: add helper functions from busybox
Import the following helper functions from Busybox-1.33.1 which are
required by printf.c:
process_escape_sequence from libbb/process_escape_sequence.c,
skip_whitespace from libbb/skip_whitespace.c,
overlapping_strcpy from libbb/safe_strncpy.c
src-url: https://git.busybox.net/busybox/
commit bcc5b0e6caca6c7602a6a41f "Bump version to 1.33.1"
version: 1.33.1
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
Tom Rini [Tue, 27 Jul 2021 15:42:31 +0000 (11:42 -0400)]
Merge tag 'u-boot-amlogic-20210727' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add SMBIOS info for Khadas VIM boards
- Fix meson-axg-mipi PHY build
- Fix VIM3 board phy-names property setup
- Return correct value for non emmc boot sources on VIM3
- add kernel compression vars
Tom Rini [Tue, 27 Jul 2021 13:11:25 +0000 (09:11 -0400)]
Merge tag 'u-boot-stm32-20210727' of https://source.denx.de/u-boot/custodians/u-boot-stm
- FIP Enable OP-TEE and TZC support in SPL for STM32MP15 SoC
- Add stm32mp15 missing SPI clock support
- Manage pull-up on gpio button STM32MP15 boards
- Correct STM32MP15 boot when TAMPER registers are invalid
- Fix EMMC pinmux on STM32MP15 Avenger96 board
projects / u-boot.git / log
