Jagan Teki [Thu, 28 Mar 2019 08:16:11 +0000 (13:46 +0530)]
clk: sunxi: a10: Add CLK_AHB_GMAC
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fabio Estevam [Wed, 27 Mar 2019 23:03:39 +0000 (20:03 -0300)]
pico-imx7d: README: Recommend the usage of a USB hub
Since commit 9e3c0174da842 ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Jagan Teki [Thu, 21 Mar 2019 08:35:53 +0000 (14:05 +0530)]
configs: icorem6: Use imx6 cratch register for bootcount
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.
Fixes: 4eb9aa39350e ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
Adam Ford [Sun, 3 Mar 2019 22:22:45 +0000 (16:22 -0600)]
ARM: imx6q_logic: Enable UUID support
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Fabio Estevam [Thu, 21 Mar 2019 13:59:06 +0000 (10:59 -0300)]
pico-imx6ul: Fix eMMC boot after DM_MMC conversion
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Tom Rini [Sun, 31 Mar 2019 11:25:00 +0000 (07:25 -0400)]
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
Marek Vasut [Sat, 30 Mar 2019 06:43:55 +0000 (07:43 +0100)]
ARM: rmobile: rcar-gen2: Activate bootm_size
Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.
Marek Vasut [Sat, 30 Mar 2019 05:10:49 +0000 (06:10 +0100)]
ARM: rmobile: alt: Remove R8A7794_ETHERNET_B
The R8A7794_ETHERNET_B config option is unused and based on the
description, this is a setting which should be fully done on a
DT level instead. Remove this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Matthias Brugger [Thu, 28 Mar 2019 13:47:39 +0000 (14:47 +0100)]
RPi: Add mbrugger as board maintainer
I took over maintainership from Alex Graf with commit 3157bbfa18 ("rpi: Make Matthias maintainer")
But I forgot to update the board maintainer file.
This patch adds myself to the game.
Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Alexander Graf <agraf@csgraf.de>
Andrew F. Davis [Tue, 26 Mar 2019 15:12:01 +0000 (10:12 -0500)]
configs: ti: Move FIT image load address to avoid overwrite
The FIT image is loaded to 0x8700_0000 followed by extracting from that
several large images also into the 0x8x00_0000 range. Large images
can end up overwriting the FIT image as it is being extracted from.
Move the FIT load address clear out to 0x9000_0000, this will require
a board to have at least 256MB of DRAM, if less then more careful
planning will be required for that platform.
BOUGH CHEN [Tue, 26 Mar 2019 06:24:17 +0000 (06:24 +0000)]
mmc: correct the HS400 initialization process
After the commit b9a2a0e2e9c0 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tom Rini [Fri, 29 Mar 2019 13:21:30 +0000 (09:21 -0400)]
Merge tag 'efi-2019-04-rc5-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI system for v2019.04-rc5-2
This patch series contains a bug fix for a double free in a UEFI unit
test. The other patches are documentation only (except for the definition
of two additional constants).
David Wu [Tue, 12 Feb 2019 11:51:51 +0000 (19:51 +0800)]
pinctrl: rockchip: Add 32bit writing function for rk3288 gpio0 pinctrl
There are no higher 16 writing corresponding bits for pmu_gpio0's
iomux/drive/pull at rk3288, need to read the value from register
firstly. Add the flag to distinguish it from normal registers.
Philipp Tomsich [Fri, 29 Mar 2019 08:21:13 +0000 (09:21 +0100)]
Revert "rockchip: Drop call to rockchip_dnl_mode_check() for now"
Due to a final resolution not coming up in time for 2019.04 and
following the consensus on the discussion, we'll keep this around
for 2019.04 after all.
Tom Rini [Fri, 29 Mar 2019 01:44:49 +0000 (21:44 -0400)]
Merge tag 'arc-last-minute-for-2019.04' of git://git.denx.de/u-boot-arc
This is last minute change which fixes problems in runtime on
AXS10x board caused by some changes in NAND framework and
tiny documentation improvement.
Anyways NAND flash storage was never really used on the board for various
reasons and now we decided to drop it for good.
Note this change only touches 1 ARC board so that should be safe for others.
As usual - build tested in TravisCI, see
https://travis-ci.org/abrodkin/u-boot/builds/512041342
Jernej Skrabec [Sun, 24 Mar 2019 18:26:40 +0000 (19:26 +0100)]
sunxi: video: HDMI: Fix clock setup
Currently, HDMI driver doesn't consider minimum and maximum allowed rate
of pll3 (video PLL). It works most of the time, but not always.
Consider monitor with resolution 1920x1200, which has pixel clock rate
of 154 MHz. Current code would determine that pll3 rate has to be set to
154 MHz. However, minimum supported rate is 192 MHz. In this case video
output just won't work.
The reason why the driver is written in the way it is, is that at the
time HDMI PHY and clock configuration wasn't fully understood. But now
we have needed knowledge, so the issue can be fixed.
With this fix, clock configuration routine uses full range (1-16) for
clock divider instead of limited one (1, 2, 4, 11). It also considers
minimum and maximum allowed rate for pll3.
Eugeniy Paltsev [Wed, 27 Mar 2019 13:53:43 +0000 (16:53 +0300)]
ARC: AXS10x: drop NAND support
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Patrick Delaunay [Wed, 27 Feb 2019 14:20:38 +0000 (15:20 +0100)]
Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Define the function board_spi_cs_gpio only when needed,
only called in drivers/spi/mxc_spi.c.
That avoid compilation issue for tqma6s_wru4_mmc_defconfig
when CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS are not
defined (CMD_SF not defined) after migration in KConfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 27 Feb 2019 14:20:34 +0000 (15:20 +0100)]
exynos: replace CONFIG_ENV_SPI_BASE by CONFIG_SYS_SPI_BASE
Replace CONFIG_ENV_SPI_BASE by the better CONFIG_SYS_SPI_BASE
(it is not the location for environment but the location for U-Boot)
and, as it is the only platform with use this define, remove
it from whitelist.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tom Rini [Mon, 25 Mar 2019 21:26:38 +0000 (17:26 -0400)]
Merge branch '2019-03-25-master-imports'
- 3 bugfixes:
- mmc: Align MMC_TRACE with tiny printf
- scripts/Makefile.extrawarn: Silence more DTC warnings
- rsa: check that pointer checksum isn't NULL before using it
Marek Vasut [Mon, 18 Mar 2019 22:43:10 +0000 (23:43 +0100)]
mmc: tmio: Clamp SD_SECCNT to 16bit values on 16bit IP
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Marek Vasut [Mon, 18 Mar 2019 04:11:42 +0000 (05:11 +0100)]
clk: renesas: Fix SDH clock divider decoding on Gen2
The gen2_clk_get_sdh_div() function is supposed to look up the
$val value read out of the SDCKCR register in the supplied table
and return the matching divider value. The current implementation
was matching the value from SDCKCR on the divider value in the
table, which is wrong. Fix this and rework the function a bit
to make it more readable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Mon, 18 Mar 2019 02:20:31 +0000 (03:20 +0100)]
ARM: dts: rmobile: Increase off-on delay on the SD Vcc regulator
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc
pin that the usual toggling of regulator to power the card off and on
is insufficient. When the card is calibrated into UHS SDR104 mode, it
will remain in that mode across the power cycle and subsequent attempt
to communicate with the card will fail.
The test with this card is to insert it into an SDHI slot and perform
"mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail.
Fix this problem by increasing the off-on delay from 0 to 20 mS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 23 Mar 2019 17:54:45 +0000 (18:54 +0100)]
mmc: Align MMC_TRACE with tiny printf
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 22 Mar 2019 13:47:39 +0000 (09:47 -0400)]
scripts/Makefile.extrawarn: Silence more DTC warnings
While our "extrawarns" logic has gotten out of sync with upstream
Kbuild, for now lets start by bringing in the latest set of DTC_FLAGS
from the Linux Kernel 5.0 to match their behavior in silencing warnings
from dtc.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 22 Mar 2019 23:09:58 +0000 (19:09 -0400)]
Merge branch '2019-03-22-master-imports'
- Don't attempt to write to ext4 volumes with the metadata_csum feature
we don't support
- Correct how we build dtb files.
- Fix regression on SPL_FIT with FIT_IMAGE_TINY
- Minor TI platform fixes
Andrew F. Davis [Mon, 11 Feb 2019 14:00:08 +0000 (08:00 -0600)]
board: ti: Move fastboot functions out of TI_SECURE_DEVICE ifdef
When these were moved from mach-omap2 to board files they got placed
inside TI_SECURE_DEVICE ifdef block, they are not secure only, move
them up and out.
Fixes: 413b90777f8d ("ti: fastboot: Move weak overrides to board files") Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Stefan Roese [Mon, 11 Feb 2019 07:43:25 +0000 (08:43 +0100)]
pci: Add comment to mention difference in DEVFN usage in U-Boot vs Linux
This patch adds a comment to the header with the PCI_foo macros related
to DEVFN to explain the difference in U-Boot vs Linux.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
I am not sure if I correctly understood the log of commit 27cb7300ffda
("Ensure device tree DTS is compiled"), but the code-diff looks like
it was trying to solve the missed re-compilation when .dts was modified.
Recently, commit 2737dfe096b6 ("kbuild: make arch-dtbs target PHONY")
fixed the issue in a more correct and more complete way.
Anyway, since the former commit, we see a clumsy log like this:
make[2]: 'arch/sandbox/dts/sandbox.dtb' is up to date
Another problem is, it created multiple paths to descend into
arch/*/dts/, causing a race in parallel building.
Alexander Graf [Wed, 20 Feb 2019 16:14:49 +0000 (17:14 +0100)]
armv8: Disable exception vectors in SPL by default
Commit 1416e2d2253 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Marek Vasut [Wed, 6 Mar 2019 21:04:00 +0000 (22:04 +0100)]
Makefile: Do not pass -E to mkimage when SPL has full fitImage support
When the SPL has full fitImage support, do not generate fitImage with
external data. The full fitImage code assumes the entire fitImage is
loaded in RAM, and the SPL uses fdt_totalsize() to determine the size
of the whole fitImage, which can not work with external data.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com>
i2c: i2c_cdns: Fix below warnings with checker tool
This patch fixes below warnings found with checker tool.
The variable len in i2c_msg struct is of unsigned type
and it is received as recv_count which is unsigned type
but it is checked with < 0 which is always false, hence
removed it.
The local variable curr_recv_count is declared as signed
type and compared aginst unsigned recv_count which is
incorrect. This is fixed by declaring it as unsigned type.
drivers/i2c/i2c-cdns.c: In function ‘cdns_i2c_read_data’:
drivers/i2c/i2c-cdns.c:317:18: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
if ((recv_count < 0))
^
drivers/i2c/i2c-cdns.c:340:24: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
updatetx = recv_count > curr_recv_count;
^
drivers/i2c/i2c-cdns.c:361:39: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
while (readl(®s->transfer_size) !=
efi_loader: correct parameter size in efi_allocate_pool
efi_allocate_pages() expects a (uint64_t *) pointer to pass the address of
the assigned memory. If we pass the address of a pointer here, an illegal
memory access occurs on 32bit systems.
Fixes: 282a06cbcae8 ("efi_loader: Expose U-Boot addresses in memory map
for sandbox") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 19 Mar 2019 23:58:48 +0000 (19:58 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
Chris Packham [Mon, 18 Mar 2019 07:51:58 +0000 (20:51 +1300)]
ARM: kirkwood: disable dcache for Kirkwood boards
Prior to commit 93b283d49f93 ("ARM: CPU: arm926ejs: Consolidate cache
routines to common file") the kirkwood boards didn't have and dcache
support. The network and usb drivers rely on this. Set
CONFIG_SYS_DCACHE_OFF in the Kirkwood specific config.h.
Reported-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Sat, 16 Mar 2019 07:46:20 +0000 (20:46 +1300)]
ARM: mvebu: use correct name for pcie controller
When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 21:11:14 +0000 (10:11 +1300)]
mv_ddr: ddr3: only use active chip-selects when tuning ODT
Inactive chip-selects will give invalid values for read_sample so don't
consider them when trying to determine the overall min/max read sample.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/18] Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 21:11:13 +0000 (10:11 +1300)]
mv_ddr: ddr3: fix tRAS timimg parameter
Based on the JEDEC standard JESD79-3F. The tRAS timings should include
the highest speed bins at a given frequency. This is similar to commit 683c67b ("mv_ddr: ddr3: fix tfaw timimg parameter") where the wrong
comparison was used in the initial implementation.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/15] Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 07:53:23 +0000 (20:53 +1300)]
ARM: kirkwood: add spi0 alias for dreamplug
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Chris Packham <judge.packham@gmail.com> Tested-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log
