Holger Brunck [Fri, 9 Oct 2020 15:21:33 +0000 (17:21 +0200)]
km/common: change ubicopy variable
Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.
Holger Brunck [Fri, 9 Oct 2020 15:21:32 +0000 (17:21 +0200)]
km: adapt defines and variables for new memory layout
Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> CC: Heiko Schocher <hs@denx.de> CC: Tom Rini <trini@konsulko.com> Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com> Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Remove old values from kmp204x.h] Signed-off-by: Tom Rini <trini@konsulko.com>
When building on a 32bit host the following warning occurs:
tools/image-host.c: In function ‘fit_image_read_data’:
tools/image-host.c:296:56: warning: format ‘%ld’ expects argument of
type ‘long int’, but argument 3 has type ‘__off64_t’
{aka ‘long long int’} [-Wformat=]
printf("File %s don't have the expected size (size=%ld, expected=%d)\n",
~~^
%lld
filename, sbuf.st_size, expected_size);
~~~~~~~~~~~~
tools/image-host.c:311:62: warning: format ‘%ld’ expects argument of
type ‘long int’, but argument 4 has type ‘__off64_t’
{aka ‘long long int’} [-Wformat=]
printf("Can't read all file %s (read %zd bytes, expexted %ld)\n",
~~^
%lld
filename, n, sbuf.st_size);
~~~~~~~~~~~~
Fix the format strings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Holger Brunck [Thu, 8 Oct 2020 10:27:22 +0000 (12:27 +0200)]
km: fix license string and compatible strings
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com> CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> CC: Heiko Schocher <hs@denx.de> CC: Marek Vasut <marex@denx.de> CC: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Naoki Hayama [Thu, 8 Oct 2020 04:16:18 +0000 (13:16 +0900)]
README: Update links to mailing list archives
This patch includes these updates
- Change http://lists.denx.de/pipermail/u-boot
to https://lists.denx.de/pipermail/u-boot
- http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
is broken, so remove it
- Another archive https://marc.info/?l=u-boot
is available, so add it
Additional information:
dir.gmane.org has moved to news.gmane.io, but it only allows
access to the archive via NNTP.
- Server: news.gmane.io
- Group : gmane.comp.boot-loaders.u-boot
I don't include this information in this patch because
it's not very useful without web interfaces.
Sean Anderson [Wed, 7 Oct 2020 18:37:44 +0000 (14:37 -0400)]
timer: Return count from timer_ops.get_count
No timer drivers return an error from get_count. Instead of possibly
returning an error, just return the count directly.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Wed, 7 Oct 2020 18:37:43 +0000 (14:37 -0400)]
doc: Document timer API
This adds kerneldocs for <timer.h>.
I don't know who should maintain doc/api/timer.rst, since the timer
subsystem seems to be maintained by SoC maintainers. MAINTAINERS is left
un-updated for the moment.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This code is intended do prevent one from setting a shell variable abc
by doing
abc=123
if an environment variable named abc already exists. However, the
check is broken, since the env_get is done before the split on =, so
we look up whether an environment variable "abc=123" exists, which is
obviously never the case.
One could move the code to below the split on =, but instead, just
remove it, saving a little .text: The check has never worked as
intended (it goes all the way back to the initial git commit), and it
would anyway not guard against one first setting the shell variable,
then doing 'env set abc xyz'.
Naoki Hayama [Wed, 7 Oct 2020 02:22:24 +0000 (11:22 +0900)]
cosmetic: image: Fix comments and the order of definitions
Fix some comments about functions.
Move genimg_get_comp_name() above genimg_get_short_name() because
genimg_get_comp_name() is related to get_table_entry_name().
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp> Reviewed-by: Simon Glass <sjg@chromium.org>
Naoki Hayama [Wed, 7 Oct 2020 02:21:55 +0000 (11:21 +0900)]
mkimage: Skip adding non-existent IDs to a list
In show_valid_options(), this patch introduces checking whether
a category has an entry ID. If not, adding it to a list for output
is skipped before calling qsort().
This patch will affect all kinds of image header categories
(-A, -C, -O and -T flags).
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp> Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig: Use hex values for CONFIG_{SPL,TPL}_SIZE_LIMIT
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 28 Sep 2020 00:46:17 +0000 (18:46 -0600)]
syscon: Drop the logging in syscon_get_by_driver_data()
This function can be called when it is not known whether it will find
anything. This results in confusing log messages if the device is not
found. It is better for the caller to log the failure, if necessary.
Tom Rini [Thu, 22 Oct 2020 12:25:41 +0000 (08:25 -0400)]
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
Marek Vasut [Mon, 19 Oct 2020 21:40:26 +0000 (23:40 +0200)]
Revert "Fix data abort caused by mis-aligning FIT data"
This reverts commit eb39d8ba5f0d1468b01b89a2a464d18612d3ea76.
The commit breaks booting of fitImage by SPL, the system simply hangs.
This is because on arm32, the fitImage and all of its content can be
aligned to 4 bytes and U-Boot expects just that.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Reuben Dowle <reuben.dowle@4rf.com> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Vasut <marex@denx.de>
Patrick Delaunay [Thu, 15 Oct 2020 12:28:17 +0000 (14:28 +0200)]
stm32mp: stm32prog: accept device without partition
When partitions are not available on a device the command stm32prog raises
an error but a device can have no partition to check in init_device()
and the command need to continue to the next part_id.
This patch correct an issue for ram0 target, when block_dev and mtd
are NULL.
For example with the simple flashlayout file:
Opt Part Name Type Device Offset Binary
- 0x01 fsbl Binary none 0x0 tf-a-serialboot.stm32
- 0x03 ssbl Binary none 0x0 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSytem ram0 0xC4000000 stm32mp157f-ev1.dtb
Fixes: ffc405e63b94 ("stm32mp: stm32prog: add upport of partial update") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
MAINTAINERS: Add stm32 and stm regexp for ARM STM STM32MP platform
Add files and directories regex "stm32" and "stm" in "ARM STM STM32MP"
platform to avoid missing files or drivers supported by the
STMicroelectronics series STM32MP15x.
This patch adds the rules already used in Linux kernel for
ARM/STM32 ARCHITECTURE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60ba1 ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Marek Vasut [Thu, 8 Oct 2020 13:14:58 +0000 (15:14 +0200)]
ARM: dts: stm32: Do not set eth1addr if KS8851 has EEPROM
In case the KS8851 has external EEPROM attached to it, do not set
eth1addr at all. The network stack will read the MAC out of the
KS8851 and set eth1addr accordingly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
stm32mp: limit size of cacheable DDR in pre-reloc stage
In pre-reloc stage, U-Boot marks cacheable the DDR limited by
the new config CONFIG_DDR_CACHEABLE_SIZE.
This patch allows to avoid any speculative access to DDR protected by
firewall and used by OP-TEE; the "no-map" reserved memory
node in DT are assumed after this limit:
STM32_DDR_BASE + DDR_CACHEABLE_SIZE.
Without security, in basic boot, the value is equal to STM32_DDR_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
mmc: stm32_sdmmc2: Use mmc_of_parse() to read host capabilities
mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.
mmc: mmc_of_parse: Enable 52 MHz support with "cap-mmc-highspeed"
"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.
Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Tested-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Ralph Siemsen [Tue, 29 Sep 2020 18:52:05 +0000 (14:52 -0400)]
arm: socfpga: fix Gen5 enable of EMAC via FPGA
An earlier conversion from struct to defines introduced two errors, both
related to setup of EMAC routed via the FPGA. One of the offsets was
incorrect, and the EMAC0/EMAC1 were swapped.
The effect of this was rather odd: both ports could operate at gigabit,
but one of them would fail to transmit when operating at 100Mbit.
Fixes: db5741f7a85ec3ee79b64496172afaa7dc2cb225 ("arm: socfpga: Convert system manager from struct to defines") Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Chunfeng Yun [Wed, 14 Oct 2020 07:08:32 +0000 (15:08 +0800)]
configs: mt8512: enable fastboot and USB host related configs
Enable mtu3, xhci, tphy drivers.
Device mode: enable fastboot;
Host mode: enable USB, FAT commands, and fixed regulator,
mass storage drivers;
Due to device mode is enabled by default, comment out
the host mode config here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Chunfeng Yun [Wed, 14 Oct 2020 07:08:26 +0000 (15:08 +0800)]
dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
Add dt-binding for MediaTek USB3 DRD Driver which it's ported
from the Linux kernel DTS binding:
Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
Commit ID: 34d0545978b6 ("dt-bindings: usb: mtu3: fix typo of DMA clock name")
Due to Dual-Role switch is not supported in Uboot, some properties
are removed or changed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Chance.Yang [Tue, 6 Oct 2020 02:55:49 +0000 (10:55 +0800)]
usb: dwc2: Fix control OUT transfer issue
In buffer DMA mode, gadget should re-configure EP 0 to received SETUP
packets when doeptsiz.xfersize is equal to a setup packet size(8 bytes)
and EP 0 is in WAIT_FOR_SETUP state.
Since EP 0 is not enabled in WAIT_FOR_SETUP state, SETUP packets is NOT
received from RxFifo and wriiten to the external memory.
Patrick Wildt [Wed, 7 Oct 2020 09:04:33 +0000 (11:04 +0200)]
efi_loader: fix use after free in receive path
With DM enabled the ethernet code will receive a packet, call
the push method that's set by the EFI network implementation
and then free the packet. Unfortunately the push methods only
sets a flag that the packet needs to be handled, but the code
that provides the packet to an EFI application runs after the
packet has already been freed.
To rectify this issue, adjust the push method to accept the packet
and store it in a temporary buffer. The EFI application then gets
the data copied from that buffer. This way the packet is cached
until is is needed.
The DM Ethernet stack tries to receive 32 packets at once, thus
we better allocate as many buffers as the stack.
Signed-off-by: Patrick Wildt <patrick@blueri.se> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 19 Oct 2020 13:29:05 +0000 (09:29 -0400)]
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Patrick Delaunay [Mon, 28 Sep 2020 09:30:14 +0000 (11:30 +0200)]
configs: migrate CONFIG_VIDEO_BMP_GZIP to defconfigs
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Neil Armstrong [Fri, 2 Oct 2020 09:16:09 +0000 (11:16 +0200)]
video: dw-mipi-dsi: permit configuring the escape clock rate
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 2 Oct 2020 09:16:08 +0000 (11:16 +0200)]
video: dw-mipi-dsi: driver-specific configuration of phy timings
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sean Anderson [Tue, 13 Oct 2020 19:20:52 +0000 (15:20 -0400)]
test: Fix sandbox tests failing to build
syslog_test.h is in test/log/, not include/
Fixes: 52d3df7fef ("log: Allow LOG_DEBUG to always enable log output") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log
