Tom Rini [Tue, 20 Sep 2016 01:55:34 +0000 (21:55 -0400)]
PowerPC: Update MIP405/MIP405T to use Kconfig better
Convert CONFIG_MIP405T from SYS_EXTRA_OPTIONS to a real config
There are two boards, MIP405 and MIP405T that have a few differences.
Start by checking for CONFIG_TARGET_MIP405. Then introduce
CONFIG_TARGET_MIP405T and use that not CONFIG_MIP405T. Next, convert
also convert the usage of CONFIG_ISO_STRING to be based on Kconfig.
I took a closer look at this after the commit was applied, and found
CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is
actually too big for some boards. Perhaps 0x800 is enough, but the
situation varies board by board.
Let's postpone our decision until we come up with a better idea.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 26 Jul 2016 00:59:16 +0000 (18:59 -0600)]
dtoc: Support finding the offset of a property
Add a way to find the byte offset of a property within the device tree. This
is only supported with the normal libfdt implementation since fdtget does
not provide this information.
Simon Glass [Tue, 26 Jul 2016 00:59:14 +0000 (18:59 -0600)]
dtoc: Support deleting device tree properties
Add support for deleting a device tree property. With the fallback
implementation this uses fdtput. With libfdt it uses the API call and
updates the offsets afterwards.
Simon Glass [Tue, 26 Jul 2016 00:59:13 +0000 (18:59 -0600)]
dtoc: Move to using bytearray
Since we want to be able to change the in-memory device tree using libfdt,
use a bytearray instead of a string. This makes interfacing from Python
easier.
Simon Glass [Tue, 26 Jul 2016 00:59:12 +0000 (18:59 -0600)]
dtoc: Prepare for supporting changing of device trees
For binman we need to support deleting properties in the device tree. This
will change the offsets of nodes after the deletion. In preparation, add
code to keep track of when the offsets are invalid, and regenerate them.
Simon Glass [Tue, 26 Jul 2016 00:59:10 +0000 (18:59 -0600)]
dtoc: Allow the device tree to be compiled from source
If a source device tree is provide to the Fdt() constructors, compile it
automatically. This will be used in tests, where we want to build a
particular test .dts file and check that it works correctly in binman.
Simon Glass [Tue, 26 Jul 2016 00:59:09 +0000 (18:59 -0600)]
patman: Add a library to handle logging and progress
When tools want to display information of varying levels of importance, it
helps to provide the user with control over the verbosity of these messages.
Progress messages work best if they are displayed and then removed from the
display when no-longer relevant.
Add a new tout library (terminal out) to handle these tasks.
Simon Glass [Tue, 26 Jul 2016 00:59:08 +0000 (18:59 -0600)]
patman: Add a tools library for using temporary files
For tools which want to use input files and temporary output, it is useful
to have the handling of these dealt with in one place. Add a new library
which allows input files to be read, and output files to be written, all
based on a common directory structure.
Simon Glass [Tue, 26 Jul 2016 00:59:05 +0000 (18:59 -0600)]
dtoc: Move BytesToValue() and GetEmpty() into PropBase
These functions are currently in a separate fdt_util file. Since they are
only used from PropBase and subclasses, it makes sense for them to be in the
PropBase class.
Move these functions into fdt.py along with the list of types.
Simon Glass [Tue, 26 Jul 2016 00:59:04 +0000 (18:59 -0600)]
dtoc: Create a base class for Fdt
At present we have two separate implementations of the Fdt library, one which
uses fdtget/fdtput and one which uses libfdt (via swig).
Before adding more functionality it makes sense to create a base class for
these. This will allow common functions to be shared, and make the Fdt API
a little clearer.
Create a new fdt.py file with the base class, and adjust fdt_normal.py and
fdt_fallback.py to use it.
Simon Glass [Tue, 26 Jul 2016 00:59:02 +0000 (18:59 -0600)]
dtoc: Move the fdt library selection into fdt_select
Rather than have dtc worry about which fdt library to use, move this into
a helper file. Add a function which creates a new Fdt object and scans it,
regardless of the implementation.
Simon Glass [Tue, 26 Jul 2016 00:59:00 +0000 (18:59 -0600)]
patman: Adjust command.Output() to raise an error by default
It is more useful to have this method raise an error when something goes
wrong. Make this the default and adjust the few callers that don't want to
use it this way.
Stefan Brüns [Thu, 11 Aug 2016 20:52:04 +0000 (22:52 +0200)]
sandbox: Add "host size" hostfs command for fs test
This complements the size/fatsize/ext4size commands added in
commit cf6598193aed5de8855eaf70c1994f2bc437255a
load, save and ls are already implemented for hostfs, now tests can
cover the same operations on hostfs and emulated block devices.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Simon Glass <sjg@chromium.org>
Stefan Brüns [Thu, 11 Aug 2016 20:52:03 +0000 (22:52 +0200)]
sandbox: document support of block device emulation
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Acked-by: Simon Glass <sjg@chromium.org>
Changed 'Sandbox' to 'sandbox' in subject: Signed-off-by: Simon Glass <sjg@chromium.org>
ARM: uniphier: collect clock/PLL init code into a single directory
Now PLLs for DRAM controller are initialized in SPL, and the others
in U-Boot proper. Setting up all of them in a single directory will
be helpful when we want to share code between SPL and U-Boot proper.
ARM: uniphier: move PLL init code to U-Boot proper where possible
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper. Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers. Use them by
calling pinctrl_generic_set_state() directly.
Hans de Goede [Sat, 17 Sep 2016 14:02:38 +0000 (16:02 +0200)]
sunxi: musb: Re-init musb controller on repeated probe calls
With sunxi-musb musb_lowlevel_init() can fail when a charger; or no cable
is plugged into the otg port.
To avoid leaking the struct musb allocated by musb_init_controller()
on repeated musb_usb_probe() calls, we were caching its result.
But musb_init_controller() does more, such as calling sunxi_musb_init()
which enables the clocks.
Not calling sunxi_musb_init() causes the musb controller to stop working
after a "usb reset" since that calls musb_usb_remove() which disables the
clocks.
This commit fixes this by removing the caching of the struct returned
from musb_init_controller(), it replaces this by free-ing the allocated
memory in musb_usb_remove() and calling musb_usb_remove() on
musb_usb_probe() errors to ensure proper cleanup.
While at it also make musb_usb_probe() and musb_usb_remove() static.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: musb: Power off OTG port VBUS when disabled
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e6604 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Mon, 12 Sep 2016 07:52:52 +0000 (09:52 +0200)]
sunxi: axp2xx: disable ldoio0/1 at boot
When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable them at axp_init time (iow as early as possible)
to remove this difference between a cold boot and a reboot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Simon Glass [Tue, 13 Sep 2016 05:18:30 +0000 (23:18 -0600)]
spear: Use upper case for CONFIG options
There are a few options which use lower case. We should use upper case for
all CONFIG options.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add usbtty/nand hunk to include/configs/spear3xx_evb.h] Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Tue, 13 Sep 2016 13:05:23 +0000 (07:05 -0600)]
Kconfig: spl: Add SPL support options to Kconfig
There are a lot of SPL options in U-Boot to enable various features and
drivers. Currently these do not use Kconfig. Add them to Kconfig along
with suitable help, and drop them from the README.
Simon Glass [Tue, 13 Sep 2016 05:18:25 +0000 (23:18 -0600)]
Use separate options for TPL support
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.
With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.
Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.
Simon Glass [Tue, 13 Sep 2016 05:18:23 +0000 (23:18 -0600)]
arm: fsl: Adjust ordering of #ifndef CONFIG_SPL_BUILD
The secure boot header files incorrectly define SPL options only if
CONFIG_SPL_BUILD is defined. This means that the options are only enabled
in an SPL build, and not with a normal 'make xxx_defconfig'. This means
that moveconfig.py cannot work, since it sees the options as disabled even
when they may be manually enabled in an SPL build.
Simon Glass [Tue, 13 Sep 2016 05:18:21 +0000 (23:18 -0600)]
moveconfig: Add an option to commit changes
The moveconfig tool is quite clever and generally produces results that
are suitable for sending as a patch without further work. The main required
step is to add the changes to a commit.
Add an option to do this automatically. This allows moveconfig to be used
from a script to convert multiple CONFIG options, once per commit.
Simon Glass [Tue, 13 Sep 2016 05:18:20 +0000 (23:18 -0600)]
moveconfig: Add an option to skip prompts
At present it is not easy to use moveconfig from a script since it asks
for user input a few times. Add a -y option to skip this and assume that
'y' was entered.
projects / u-boot.git / log
