Philippe Reynes [Mon, 14 Oct 2019 17:41:06 +0000 (19:41 +0200)]
ubi: env: fix redundand management
We check (with a #if defined()) the config ENV_UBI_VOLUME_REDUND
to know if there is a redundant env. But this config is a string
and is always defined with env is in ubi, so we always consider
that a redundand env is used.
To fix this issue, I've added a hidden flag ENV_UBI_IS_VOLUME_REDUND
that is true when ENV_UBI_VOLUME_REDUND is not "". Then, I check
this flag in the code, instead of the string ENV_UBI_VOLUME_REDUND.
hs: fixed typo s/condider/consider
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Tue, 17 Sep 2019 07:17:53 +0000 (09:17 +0200)]
ubi: Add "skipcheck" command to set/clear this bit in the UBI volume hdr
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Quentin Schulz <quentin.schulz@bootlin.com> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Dannenberg <dannenberg@ti.com>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Quentin Schulz <quentin.schulz@bootlin.com> Cc: Boris Brezillon <boris.brezillon@bootlin.com>
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
Tom Rini [Mon, 14 Oct 2019 11:28:32 +0000 (07:28 -0400)]
Merge tag 'mmc-10-10-2019' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Use imx_ddr_size() to retrieve the total DDR size instead
of passing a hardcoded memory size.
imx_ddr_size() calculates the memory size based on the actual
MMDC registers values and is useful to detect misconfigurations,
so switch to this more robust approach.
Yannick Fertré [Mon, 7 Oct 2019 13:29:09 +0000 (15:29 +0200)]
video: add support of panel RM68200
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Yannick Fertré [Mon, 7 Oct 2019 13:29:05 +0000 (15:29 +0200)]
dm: Add a dsi host uclass
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Igor Opaniuk [Mon, 22 Jul 2019 09:05:06 +0000 (12:05 +0300)]
colibri_imx7: provide proper node name to pmic_get
Implementation of pmic_get() uses uclass_find_device_by_name(), which
behaviour was changed in 4213609cc7
("drivers: core: use strcmp when find device by name"). Now we have to
supply full node name with unit address.
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
DRAM: 512 MiB
initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19)
ERROR Please RESET the board
Fixes: 4213609cc7("drivers: core: use strcmp when find device by name") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sjoerd Simons [Tue, 18 Jun 2019 20:13:20 +0000 (22:13 +0200)]
spl, Makefile: Take external offset into account for fit images
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Ye Li [Fri, 12 Jul 2019 09:33:52 +0000 (09:33 +0000)]
imx8: Jump from alias to OCRAM address at SPL init
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Lukasz Majewski [Thu, 10 Oct 2019 14:11:24 +0000 (16:11 +0200)]
imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD boot
The TPC70 can boot from SD card (debug/development) and eMMC (production).
The board_boot_order() function provides a run time check for the device
from which one wants to boot (it is selected by GPIO pins setup).
Moreover, a fallback to SD card is provided if the detection is not
possible or working properly.
Adam Ford [Wed, 9 Oct 2019 17:53:57 +0000 (12:53 -0500)]
ARM: imx6q_logic: Remove legacy pinmuxing code from board file.
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Adam Ford [Wed, 9 Oct 2019 17:53:56 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable Pin muxing in SPL
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 9 Oct 2019 17:53:55 +0000 (12:53 -0500)]
ARM: imx6q_logic: Enable 256KB OCRAM
Since this board config only supports, the i.MX6D/i.MX6Q configurations,
256K of on-chip RAM is available which increases the space available
to SPL to help further reduce board code and further enable device tree
functions.
This patch enables 256K of RAM.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sjoerd Simons [Thu, 20 Jun 2019 20:34:35 +0000 (22:34 +0200)]
mx6: mx6sabre common: Use more conventional spelling of fdtfile
Both the distro boot configuration as well as the general pxe support
standardized on fdtfile as the variable to hold the dtb filename.
Adjust to follow that such that e.g. "pxe boot" will just work.
Tom Rini [Fri, 11 Oct 2019 20:28:47 +0000 (16:28 -0400)]
sandbox: Remove sandbox_noblk build
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Mans Rullgard [Tue, 3 Sep 2019 14:16:50 +0000 (16:16 +0200)]
spl: mmc: Add option to set eMMC HW boot partition
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message] Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Lokesh Vutla [Tue, 1 Oct 2019 05:11:01 +0000 (10:41 +0530)]
arm: dra7xx: Hang on any failure during IOdelay recalibration
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Lokesh Vutla [Tue, 1 Oct 2019 05:11:00 +0000 (10:41 +0530)]
arm: dra7xx: Fix error path in iodelay recalibration
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
arm: dts: k3-j721e-common-proc-board: Mark main_uart0 as shared device
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Tero Kristo [Fri, 27 Sep 2019 16:14:29 +0000 (19:14 +0300)]
board: ti: am335x-ice: Configure the CDCE913 clock synthesizer
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Tero Kristo [Fri, 27 Sep 2019 16:14:28 +0000 (19:14 +0300)]
board: ti: am43xx-idk: Configure the CDCE913 clock synthesizer
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Tero Kristo [Fri, 27 Sep 2019 16:14:27 +0000 (19:14 +0300)]
board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Tero Kristo [Fri, 27 Sep 2019 16:14:26 +0000 (19:14 +0300)]
clk: cdce9xx: add support for cdce9xx clock synthesizer
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
mmc: am654_sdhci: Drop a redundant power_domain_on in probe
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Andrew F. Davis [Tue, 17 Sep 2019 19:40:25 +0000 (15:40 -0400)]
configs: ti: Use addr_fit for run_fit environment variable
When running 'run_fit' the FIT file should have been loaded at
'addr_fit', although at this point they should be the same
use this variable instead of 'loadaddr'.
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
cmd: ti: ddr3: Move the print statement after test
If the ECC is enabled over the entire memory region, we need to ensure
the printf/put calls do not modify the stack after ECC is disabled.
Moved the printf/put statements after ECC is enabled.
arm: omap: emif-common: Fix memory priming for ECC
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr cmd driver is assuming the register
contains the start address and size of the DDR address space. Because
of this some valid ecc addresses are errored out as invalid address.
Fix this calculation.
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.
projects / u-boot.git / log
