Peng Fan [Wed, 10 Jul 2019 06:43:07 +0000 (14:43 +0800)]
mmc: support hs400 enhanced strobe mode
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Ye Li [Thu, 11 Jul 2019 03:29:02 +0000 (03:29 +0000)]
mmc: fsl_esdhc_imx: fix config check issue when building in SPL
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
mmc: do not change mode when accessing a boot partition
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
mmc: During a switch, poll on dat0 if available and check the final status
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
mmc: When switching partition, use the timeout specified in the ext_csd
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
mmc: add mmc_poll_for_busy() and change the purpose of mmc_send_status()
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.
Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.
mmc: omap_hsmmc: reset FSM for DAT and CMD lines if needed before a new command
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
T Karthik Reddy [Tue, 25 Jun 2019 11:39:03 +0000 (13:39 +0200)]
mmc: sdhci: Read cd-gpio from devicetree
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 12 Jun 2019 20:26:26 +0000 (15:26 -0500)]
ARM: dts: logicpd som-lvs and torpedos: Shrink SPL DTB
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Heiko Schocher [Wed, 12 Jun 2019 04:11:46 +0000 (06:11 +0200)]
gpio: add gpio-hog support
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102) Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Adam Ford [Mon, 10 Jun 2019 18:25:08 +0000 (13:25 -0500)]
ARM: davinci: da850: Manual pinmux only when PINCTRL not available
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL). If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away. This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Adam Ford [Mon, 10 Jun 2019 18:15:55 +0000 (13:15 -0500)]
pinctrl: pinctrl-single: Add 'pinctrl-single, bits' support
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals. This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.
Tom Rini [Sat, 8 Jun 2019 16:46:18 +0000 (12:46 -0400)]
configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.
To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.
Keerthy [Thu, 6 Jun 2019 10:36:56 +0000 (16:06 +0530)]
power: regulator: Kconfig: Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565
Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.
Keerthy [Thu, 6 Jun 2019 10:36:55 +0000 (16:06 +0530)]
power: pmic: Kconfig: Add SPL_PMIC configs for palmas/lp873x/lp87565
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.
Derald D. Woods [Tue, 28 May 2019 02:22:00 +0000 (21:22 -0500)]
usb: musb-new: omap2430: Fix compilation warning with USB_MUSB_GADGET
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
[...]
CC drivers/usb/gadget/f_mass_storage.o
CC drivers/usb/musb-new/omap2430.o
CC drivers/usb/gadget/f_fastboot.o
CC env/common.o
CC env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
ret = musb_register(&platdata->plat,
^
LD drivers/usb/host/built-in.o
CC drivers/usb/gadget/f_sdp.o
CC fs/ext4/ext4fs.o
[...]
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Derald D. Woods [Tue, 28 May 2019 02:20:50 +0000 (21:20 -0500)]
ARM: omap3: evm: Enable DM_USB in defconfig
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Ezequiel Garcia [Sat, 25 May 2019 22:25:22 +0000 (19:25 -0300)]
mmc: Register only the first MMC device on MMC_TINY
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.
This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Ezequiel Garcia [Sat, 25 May 2019 22:25:21 +0000 (19:25 -0300)]
spl: Move SPL_MMC_TINY option to appear under SPL menu
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Leo Ruan [Fri, 24 May 2019 15:20:19 +0000 (17:20 +0200)]
cmd: nvedit: Add sub-command 'env info'
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using
This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com> Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default] Signed-off-by: Tom Rini <trini@konsulko.com>
Peng Fan [Wed, 22 May 2019 07:08:14 +0000 (07:08 +0000)]
drivers: core: use strcmp when find device by name
`if (!strncmp(dev->name, name, strlen(name)))` might find out
the wrong device, it might find out `dram_pll_ref_sel`, when name is
`dram_pll`. So use strcmp to avoid such issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Behún [Tue, 21 May 2019 10:04:31 +0000 (12:04 +0200)]
pci: ensure enumeration of all devices in pci_init
Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Anton Schubert <anton.schubert@gmx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: VlaoMao <vlaomao@gmail.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 11 Jul 2019 22:10:11 +0000 (18:10 -0400)]
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
Marek Vasut [Sat, 25 May 2019 20:52:20 +0000 (22:52 +0200)]
gpio: pca953x: Add TI TCA9539 compatible string
Add TI TCA9539 compatible string for yet another I2C GPIO expander.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Mario Six <mario.six@gdsys.cc> Cc: Peng Fan <van.freenix@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Sat, 25 May 2019 20:40:35 +0000 (22:40 +0200)]
arm: mach-omap2: am33xx: Init pinmux before clock
The board_early_init_f() inits clock before initing pinmux. However,
the clock configuration code might need to adjust PMIC settings of a
PMIC on I2C bus (e.g. board/ti/am335x/board.c does that). If the I2C
bus pin muxing is not configured before attempting to communicate
with the PMIC, the communication will silently fail and the prcm_init()
may configure fast enough CPU clock that the default voltage provided
by the PMIC would be insufficient and the platform would become
unstable.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Tom Rini <trini@konsulko.com>
Eugeniu Rosca [Thu, 23 May 2019 15:32:22 +0000 (17:32 +0200)]
cmd: Add 'bcb' command to read/modify/write BCB fields
'Bootloader Control Block' (BCB) is a well established term/acronym in
the Android namespace which refers to a location in a dedicated raw
(i.e. FS-unaware) flash (e.g. eMMC) partition, usually called "misc",
which is used as media for exchanging messages between Android userspace
(particularly recovery [1]) and an Android-capable bootloader.
On higher level, this allows implementing a subset of Android Bootloader
Requirements [2], amongst which is the Android-specific bootloader
flow [3]. Regardless how the latter is implemented in U-Boot ([3] being
the most memorable example), reading/writing/dumping the BCB fields in
the development process from inside the U-Boot is a convenient feature.
Hence, make it available to the users.
Some usage examples of the new command recorded on R-Car H3ULCB-KF
('>>>' is an overlay on top of the original console output):
Usage:
bcb load <dev> <part> - load BCB from mmc <dev>:<part>
bcb set <field> <val> - set BCB <field> to <val>
bcb clear [<field>] - clear BCB <field> or all fields
bcb test <field> <op> <val> - test BCB <field> against <val>
bcb dump <field> - dump BCB <field>
bcb store - store BCB back to mmc
Legend:
<dev> - MMC device index containing the BCB partition
<part> - MMC partition index or name containing the BCB
<field> - one of {command,status,recovery,stage,reserved}
<op> - the binary operator used in 'bcb test':
'=' returns true if <val> matches the string stored in <field>
'~' returns true if <val> matches a subset of <field>'s string
<val> - string/text provided as input to bcb {set,test}
NOTE: any ':' character in <val> will be replaced by line feed
during 'bcb set' and used as separator by upper layers
=> bcb dump command
Error: Please, load BCB first!
>>> Users must specify mmc device and partition before any other call
=> bcb load 1 misc
=> bcb load 1 1
>>> The two calls are equivalent (assuming "misc" has index 1)
=> bcb dump command 00000000: 62 6f 6f 74 6f 6e 63 65 2d 73 68 65 6c 6c 00 72 bootonce-shell.r 00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The output is in binary/string format for convenience
>>> The output size matches the size of inspected BCB field
>>> (32 bytes in case of 'command')
=> bcb test command = bootonce-shell && echo true
true
=> bcb test command = bootonce-shell- && echo true
=> bcb test command = bootonce-shel && echo true
>>> The '=' operator returns 'true' on perfect match
=> bcb test command ~ bootonce-shel && echo true
true
=> bcb test command ~ bootonce-shell && echo true
true
>>> The '~' operator returns 'true' on substring match
=> bcb set command recovery
=> bcb dump command 00000000: 72 65 63 6f 76 65 72 79 00 73 68 65 6c 6c 00 72 recovery.shell.r 00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The new value is NULL-terminated and stored in the BCB field
=> bcb set recovery "msg1:msg2:msg3"
=> bcb dump recovery 00000040: 6d 73 67 31 0a 6d 73 67 32 0a 6d 73 67 33 00 00 msg1.msg2.msg3.. 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
>>> --- snip ---
>>> Every ':' is replaced by line-feed '\n' (0xA). The latter is used
>>> as separator between individual commands by Android userspace
=> bcb store
>>> Flush/store the BCB structure to MMC
[1] https://android.googlesource.com/platform/bootable/recovery
[2] https://source.android.com/devices/bootloader
[3] https://patchwork.ozlabs.org/patch/746835/
("[U-Boot,5/6] Initial support for the Android Bootloader flow")
Eugeniu Rosca [Thu, 23 May 2019 15:32:21 +0000 (17:32 +0200)]
include: android_bootloader_message.h: Minimize the diff to AOSP
Perform the following updates:
- Relocate the commit id from the file to the description of U-Boot
commit. The AOSP commit is c784ce50e8c10eaf70e1f97e24e8324aef45faf5.
This is done to avoid stale references in the file itself. The
reasoning is in https://patchwork.ozlabs.org/patch/1098056/#2170209.
- Minimize the diff to AOSP, to decrease the effort of the next AOSP
backports. The background can be found in:
https://patchwork.ozlabs.org/patch/1080394/#2168454.
- Guard the static_assert() calls by #ifndef __UBOOT__ ... #endif,
to avoid compilation failures of files including the header.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 23 May 2019 11:14:08 +0000 (07:14 -0400)]
SPL: Default to disabling legacy image support when using FIT
When we have a FIT image being used by SPL by default that means the
most common case is that we'll never run into a legacy image. Disable
legacy image support by default in that case to reclaim space.
Tom Rini [Thu, 23 May 2019 11:14:07 +0000 (07:14 -0400)]
configs: Rename CONFIG_IMAGE_FORMAT_LEGACY to CONFIG_LEGACY_IMAGE_FORMAT
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Roman Kapl [Thu, 16 May 2019 16:32:48 +0000 (18:32 +0200)]
tpm: wait for valid status
The TPM specification says that the EXPECT_DATA bit is not valid until
the VALID bit is set. Wait for that bit to be set. Fixes problems with
Ifineon SPI TPM.
Miquel Raynal [Tue, 7 May 2019 12:18:54 +0000 (14:18 +0200)]
arm: spear: Return to BootROM if failing to boot from the main device
Overload the weak function board_boot_order() so that besides choosing
the main boot device, we can fallback on USB boot by returning in the
BootROM, eg. if the NOR flash is empty while it was the primary boot
medium.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Miquel Raynal [Tue, 7 May 2019 12:18:52 +0000 (14:18 +0200)]
arm: spear: Support returning to BootROM
Implement the weak board_return_to_bootrom() function so that when
enabling the spl_bootrom.c driver, one can make use of usbboot on
spear platforms. All necessary information to return to the BootROM
are stored in the BootROM's stack. The SPL stack pointer is reset so
we save the BootROM's stack pointer into the SPL .data section.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Miquel Raynal [Tue, 7 May 2019 12:18:51 +0000 (14:18 +0200)]
arm: spear: Simplify start.S organization
There is no reason to do the few spear-related initialization, in a
different procedure than 'reset'. Spare one branching and get a linear
code flow by removing this indirection.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Miquel Raynal [Tue, 7 May 2019 12:18:50 +0000 (14:18 +0200)]
arm: spear: Reference the link register with LR instead of R14
The link register is stored in R14. ARM assembly code allows to use
the 'lr' name to reference it instead of 'r14' which is not very
meaningful. Do the substitution to ease the reading.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Miquel Raynal [Tue, 7 May 2019 12:18:49 +0000 (14:18 +0200)]
arm: spear: Use PUSH/POP mnemonics when relevant
Quoting ARM "RealView Compilation Tools Assembler Guide v4.0":
PUSH and POP are synonyms for STMDB and LDM (or LDMIA), with
the base register sp (r13), and the adjusted address written
back to the base register.
PUSH and POP are the preferred mnemonic in these cases.
Let's follow this recommandation to ease the reading and substitute
LDMIA/STMDB operations with PUSH/POP mnemonics.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Miquel Raynal [Tue, 7 May 2019 12:18:44 +0000 (14:18 +0200)]
arm: spear: Drop useless board_init_r call
It is clearly stated that board_init_f should *not* call
board_init_r. Indeed, board_init_f should return. The code will
continue through arch/arm/lib/crt0.S which will do more setup before
calling board_init_r.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Stefan Roese <sr@denx.de>
Ramon Fried [Sat, 27 Apr 2019 08:15:21 +0000 (11:15 +0300)]
drivers: pci_ep: Introduce UCLASS_PCI_EP uclass
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
arm: mvebu: set 38x and 39x AVS on lower frequency
Reduce Auto Voltage Scaling VDD limit when core frequency is lower than
1600MHz. This reduces core voltage level from 1.25V to 1.15V, which
saves power.
The code is taken from Marvell's U-Boot 2013.01 revision 18.06.
Reviewed-by: Chris Packham <judge.packham@gmail.com> Tested-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Pascal Linder [Tue, 18 Jun 2019 06:44:02 +0000 (08:44 +0200)]
km/spi: remove deprecated SPI flash driver code for KM Kirkwood boards
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Pascal Linder [Tue, 18 Jun 2019 06:42:59 +0000 (08:42 +0200)]
km/spi: activate driver model for SPI flash on KM Kirkwood boards
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.
Pascal Linder [Tue, 18 Jun 2019 06:41:02 +0000 (08:41 +0200)]
km/spi: overwrite kirkwood_spi weak functions for KM Kirkwood boards
As the SPI NOR and NAND devices share the same hardware pins, the MPP
configuration has to be changed when claiming/releasing the bus. The
current configuration is saved when claiming and restored when releasing.
Furthermore, a general-purpose output is used to switch the chip-select
signal. This is now also implemented for the DM part of the kirkwood_spi
driver.
Pascal Linder [Tue, 18 Jun 2019 06:41:01 +0000 (08:41 +0200)]
km/spi: add weak functions to kirkwood_spi driver (DM part)
The weak functions, known from the legacy code, are added to the DM part
as well. For this purpose, the release operation first needs to be
implemented. KM Kirkwood boards will overwrite those weak functions to
change the MPP configuration when claiming/releasing the bus, because the
hardware pins are shared between the SPI NOR and NAND devices.
Pascal Linder [Tue, 18 Jun 2019 11:27:47 +0000 (13:27 +0200)]
km: modify Kconfig file organization for KM boards
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Cc: Mario Six <mario.six@gdsys.cc> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Stefan Roese <sr@denx.de>
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 24 May 2019 12:57:50 +0000 (14:57 +0200)]
arm: mvebu: turris_omnia: change environment address in SPI flash
The U-Boot partition is 1 MiB and environment is 64 KiB. It does not
make sense to have environment at 0xc0000 when it could be at 0xf0000
and we can have more space for U-Boot binary.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 24 May 2019 12:57:49 +0000 (14:57 +0200)]
arm: mvebu: turris_omnia: fix adapters MAC addresses
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.
Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Thu, 16 May 2019 10:04:02 +0000 (13:04 +0300)]
arm: mvebu: clearfog: set U-Boot offset for SATA boot
See the offset of U-Boot in raw SATA disk to the same value as the MMC
offset. That is 0x140 sectors from the beginning of the SPL, which is
0x141 sectors from the beginning of the device (after the MBR sector).
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log
