net: zynq_gem: Add check for 64-bit dma support by hardware
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <monstr@monstr.eu>
T Karthik Reddy [Mon, 3 Dec 2018 14:05:09 +0000 (19:35 +0530)]
arm64: zynqmp: Add new header file for zcu104 RevC
Created a new header file for zcu104 RevC board and added below
configurations to use MAC address from EEPROM.
CONFIG_ZYNQ_GEM_EEPROM_ADDR
CONFIG_ZYNQ_EEPROM_BUS
Added CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0x20 to
xilinx_zynqmp_zcu104_revC_defconfig
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 5 Oct 2018 06:55:16 +0000 (08:55 +0200)]
arm64: zynqmp: Start usb ethernet gadget automatically
If only usb ethernet gadget is enabled it can start automatically.
If more gagdets are enabled usb ethernet gadget can be bind by
"bind /amba/usb1@ff9e0000/dwc3@fe300000 usb_ether" (on zcu100)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 29 Nov 2018 09:37:49 +0000 (10:37 +0100)]
arm64: zynqmp: Add mini mtest configuration
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Michal Simek [Thu, 29 Nov 2018 14:03:40 +0000 (15:03 +0100)]
arm64: zynqmp: Enable SPL for mini qspi configuration
Wire up mini_qspi SPL with zcu102 for testing purpose.
Normally mini u-boot runs with FSBL/SPL for certain board.
Enabling SPL and configuration from zcu102 helps with testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 18 Jul 2018 10:10:02 +0000 (12:10 +0200)]
arm64: zynqmp: Setup clock-output-names for si570 chips
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 10 Jul 2018 08:18:29 +0000 (10:18 +0200)]
arm64: zynqmp: Disable ltc2952 poweroff chip
This chip is on the board but handling should be done via firmware not
via Linux driver. Changing status property to keep it in the tree to
describe it instead of removing this node completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 23 Nov 2018 08:01:44 +0000 (09:01 +0100)]
arm64: zynqmp: Enable SPL_SEPARATE_BSS by default
BSS section was all the time separated for SPL but this symbol wasn't
enabled. It is necessary to have it enabled for OF_SEPARATE
configuration where DTB is appended to u-boot with DTB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 21 Nov 2018 08:55:41 +0000 (09:55 +0100)]
arm64: zynqmp: Disable bootelf and fdt commands for mini configurations
There is no reason to enable these commands for mini configurations.
It saves some space:
aarch64: (for 2/2 boards) all -19076.0 bss -1048.0 data -1720.0
rodata -3840.0 text -12468.0
xilinx_zynqmp_mini_emmc1: all -19076 bss -1048 data -1720
rodata -3840 text -12468
xilinx_zynqmp_mini_emmc0: all -19076 bss -1048 data -1720
rodata -3840 text -12468
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 19 Nov 2018 14:46:04 +0000 (15:46 +0100)]
ARM: zynq: Guard zynq_help_text with CONFIG_SYS_LONGHELP
If SYS_LONGHELP is disabled the following warning is generated:
board/xilinx/zynq/cmds.c:496:13: warning: ‘zynq_help_text’ defined but
not used [-Wunused-variable]
Normal way for fixing this is to guard the whole variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Martin Lund [Tue, 30 Oct 2018 13:16:19 +0000 (14:16 +0100)]
mtd: nand: Arasan: Add subpage configuration support
Add support for disabling subpage write support via
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE.
Currently the Linux Arasan driver does not support subpage writes and in
case of running UBI and accessing the same UBI volume from both U-Boot
and Linux it is required to have the same subpage write configuration
else the location of the UBI headers (EC + VID) will be misaligned
(subpage vs page) and incompatible. Hence the need for disabling
subpage write support in the U-Boot Arasan NAND driver.
Signed-off-by: Martin Lund <malu@gomspace.com> Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The VCU disable bit(8) in IP disable register of efuse
is valid only if PL powered up and hence PL powerup status
has to be considered while determining the CG part also.
This patch considers the PL powerup status and ignores the VCU
disable bit if PL not powered up.
This fixes the issue of "unknown" id for CG parts if PL not powered up
and VCU bit(8) is not set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Simon Glass [Tue, 6 Nov 2018 22:21:41 +0000 (15:21 -0700)]
sf: Add a method to obtain the block-protect setting
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Simon Glass [Tue, 6 Nov 2018 22:21:40 +0000 (15:21 -0700)]
test: sf: Add a simple SPI flash test
The current test is a functional test, covering all the way from the
command line to the sandbox SPI driver. This is useful, but it is easier
to diagnose failures with a smaller test.
Add a simple test which reads and writes data and checks that it is stored
and retrieved correctly.
Simon Glass [Tue, 6 Nov 2018 22:21:39 +0000 (15:21 -0700)]
misc: Update read() and write() methods to return bytes xfered
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Simon Glass [Tue, 6 Nov 2018 22:21:36 +0000 (15:21 -0700)]
video: Update video_set_default_colors() to support invert
It is useful to be able to invert the colours in some cases so that the
text matches the background colour. Add a parameter to the function to
support this.
It is strange that function takes a private data structure from another
driver as an argument. It seems better to pass the device and have the
function internally work out how to find its required information.
Simon Glass [Tue, 6 Nov 2018 22:21:31 +0000 (15:21 -0700)]
binman: Add a way to enable debugging from the build
When the build fails due to something wrong in binman it is sometimes
useful to get a full backtrace showing the location of the failure. Add
a BINMAN_DEBUG environment variable to support this along with some
documentation.
Simon Glass [Tue, 6 Nov 2018 22:21:30 +0000 (15:21 -0700)]
spl: lz4: Allow use of lz4 compression in SPL
In some cases U-Boot is compressed and it is useful to be able to
decompress it in SPL. Add a Kconfig and Makefile change to allow this.
Note that this does not actually implement decompression.
Simon Glass [Tue, 6 Nov 2018 22:21:27 +0000 (15:21 -0700)]
sandbox: Update some drivers to work in SPL/TPL
At present sandbox drivers are mostly not used before relocation. Some of
these are needed by Chromium OS verified boot, since it uses sandbox TPL,
so update them accordingly.
Simon Glass [Tue, 6 Nov 2018 22:21:25 +0000 (15:21 -0700)]
sandbox: Add a function to read a host file
Add a way to read a file from the host filesystem. This can be useful for
reading test data, for example. Also fix up the writing function which was
not the right version, and drop the debugging lines.
Simon Glass [Tue, 6 Nov 2018 22:21:18 +0000 (15:21 -0700)]
cros_ec: Use uint instead of u8 for parameters
There is no advantage to using a u8 for function parameters. It forces
the compiler to mask values and can increase code size. Also the command
enum has been extended to 16 bits. Update the functions to use uint
instead.
Simon Glass [Tue, 6 Nov 2018 23:02:13 +0000 (16:02 -0700)]
buildman: Show boards with warning with w+
At present we should boards with warnings in the same way as those with
errors. This is not ideal. Add a new 'warn' state and show these listed
in yellow to match the actual warning lines printing with -e.
Simon Glass [Tue, 6 Nov 2018 23:02:12 +0000 (16:02 -0700)]
buildman: Rename the good, better, worse variables
At present we don't distinguish between errors and warnings when printing
the architecture summary. Rename the variables to better describe their
purpose.
'Worse' at present means we got an error, so use that as the name.
Simon Glass [Tue, 6 Nov 2018 23:02:10 +0000 (16:02 -0700)]
buildman: Only print toolchain probing with -v
At present --list-tool-chains prints a lot of information about the
toolchain-probing process. This is generally not very interesting.
Update buildman to print this only if --list-tool-chains is given
with -v.
When the device tree is missing a correct spi slave description below
the bus (compatible "spi-flash" or spi-max-frequency are missing),
the 'set_speed' callback can be called with 'speed' == 0 Hz.
At least with cadence qspi, this leads to a division by zero.
Prevent this by initializing speed to 100 kHz in this case (same
fallback value as is done in 'dm_spi_claim_bus') and issue a warning
to console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Sun, 28 Oct 2018 12:41:14 +0000 (14:41 +0200)]
fdt: restore board_fdt_blob_setup() declaration
Commit 90c08fa038451d (fdt: Add device tree memory bindings) removed the
prototype declaration of board_fdt_blob_setup(), most likely by mistake.
This didn't break the build because the only file calling this function
(lib/fdtdec.c) provides a local weak definition. Restore the
declaration.
Cc: Michael Pratt <mpratt@chromium.org> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 18 Oct 2018 18:37:05 +0000 (20:37 +0200)]
fdt: Fix uncompress_blob() for U-Boot proper
When U-Boot proper is compiled with CONFIG_MULTI_DTB_FIT and tries
to call uncompress_blob(), it fails with -ENOTSUPP. This is because
the full implementation of this function which includes compression
is available only in SPL. In U-Boot proper or if the compression is
not enabled, the blob is not compressed and thus can be passed to
locate_dtb_in_fit() in fdtdec_setup() without any changes. Pass the
blob without any changes if compression is not enabled instead of
failing.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Liviu Dudau [Mon, 15 Oct 2018 09:03:06 +0000 (10:03 +0100)]
dm: core: Widen the dump tree to show more of the driver's name.
With drivers that have prefix names that are quite long (like
'versatile_') it is useful to have a wider column for the driver's
name when dumping the device driver tree.
Also update the tests to take into account the wider output format.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
If we want to control which network interface is actually used, we have to
issue 'setenv ethrotate no'. If ethrotate is not set any interface may be
used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Hou Zhiqiang [Mon, 8 Oct 2018 08:35:47 +0000 (16:35 +0800)]
dm/pci: Change the first CFG read to Vendor ID in enumeration
As the PCIe specification recommend reading the Vendor ID register
to determine if a Function is present, read the Vendor ID of a
non-existent Function must not result in system error, so we'd better
make the first CFG read to Vendor ID instead of Header Type register
in the PCIe enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fabrice Gasnier [Mon, 12 Nov 2018 13:04:01 +0000 (14:04 +0100)]
cmd: adc: add an option to scan some or all available channels
Add new option to 'adc' command to do a single scan of:
- some channel(s), using mask argument
- all channels available on an ADC device (when optional mask is omitted).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Fabrice Gasnier [Mon, 12 Nov 2018 13:03:58 +0000 (14:03 +0100)]
dm: adc: add uclass's mask and conversion helpers
Add two functions to ADC uclass's:
- adc_raw_to_uV() to ease ADC raw value conversion to microvolts
- adc_channel_mask() to get channels on consumer side
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Sun, 11 Nov 2018 10:31:04 +0000 (12:31 +0200)]
arm64: mvebu: a8k: autodetect RAM size
Some Armada 8K boards like Macchiatobin and Clearfog GT-8K use RAM from
external DIMM. Hard coding the RAM size in the device-tree is not
convenient. Fortunately, the ATF that initializes the RAM knows the size
of RAM, and U-Boot can query the ATF using a SMC call.
The ATF maps the lower 3G of RAM starting at address 0. Higher RAM is
mapped at 4G. This leaves a 1G hole between 3G and 4G for IO
peripherals. Use a second bi_dram[] entry to describe the higher RAM
area. As a result, CONFIG_NR_DRAM_BANKS must be set to 2 to use more
than 3GB RAM.
This code in this commit is mostly taken from downstream Marvell U-Boot
code by Grzegorz Jaszczyk.
Cc: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Sun, 11 Nov 2018 10:31:02 +0000 (12:31 +0200)]
MIPS: drop asm/const.h
Commit 86f21c96f467368 (mips: Use common _AC macro now.) removed the _AC
definition from const.h. All other macros defined in const.h are not
used anywhere, and there is now no user of this header. Remove this
header.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Sun, 11 Nov 2018 10:31:01 +0000 (12:31 +0200)]
Use _AC and UL macros from linux/const.h
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Rick Chen <rick@andestech.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Sun, 11 Nov 2018 10:31:00 +0000 (12:31 +0200)]
linux/const.h: import from kernel
Combine the uapi/linux/const.h header into the kernel linux/const.h. The
next commit will use the _AC macro this header instead of the common.h
definition.
Based on Linux kernel version 4.19.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Sun, 18 Nov 2018 20:47:16 +0000 (15:47 -0500)]
Merge tag 'mips-pull-2018-11-18' of git://git.denx.de/u-boot-mips
- tree-wide: introduce LDFLAGS_STANDALONE
- MIPS: fix long-standing issue with linking of standalone programs
- MIPS: MT76xx: add GPIO and WDT drivers
- MIPS: MT76xx: various fixes and updates to gardena-smart-gateway board
- MIPS: MT76xx: various fixes and updates to linkit-smart-7688 board
Use the global MIPS specific u-boot.lds for linking standalone programs
instead of the outdated ones in examples/standalone/. Also pass --gc-sections
in LDFLAGS_STANDALONE to optimize the size of standalone programs.
Finally remove the deprecated config.mk files in arch/mips/cpu/mips[32,64]/.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Kbuild: standalone: do not ignore platform-specific OBJCOPYFLAGS
Currently the OBJCOPYFLAGS are cleared when assigning "-O srec"
or "-O binary" for standalone programs. All flags set by arch-specific
Makefiles are lost. This is bad if an arch demands arch-specific
flags for the objcopy step.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce a new Makefile variable for passing LDFLAGS to standalone
programs. Currently the variable CONFIG_STANDALONE_LOAD_ADDR is
misued on some archs to pass a specific linker script.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
Stefan Roese [Tue, 9 Oct 2018 06:59:16 +0000 (08:59 +0200)]
mips: mt76xx: linkit-smart-7688: Misc updates to dts/config/defconfig
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI support
- Enable GPIO support
- Change max image size from 0x40000 to 0x80000
A note about the baudrate change:
The original Mediatek U-Boot version used 57600 baud. Lets move to a
more common and faster speed of 115200 baud. And remove the "console="
property from the DT as its not needed.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Tue, 9 Oct 2018 06:59:14 +0000 (08:59 +0200)]
mips: mt76xx: gardena-smart-gateway: Misc updates to dts/config/defconfig
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI NOR and NAND support
- Change MTD_UBI_BEB_LIMIT to 22
- Enable MTD Support
- Enable GPIO support
- Enable watchdog support
- Enable bootcounter support
- Enable version variable
- Change max image size from 0x80000 to 0xa0000
- Change SYS_MALLOC_LEN to 16MiB (because of UBI/UBIFS)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Tue, 9 Oct 2018 06:59:10 +0000 (08:59 +0200)]
mips: mt76xx: Enable watchdog support
This patch enables and starts the watchdog on the MT7620 platform.
Currently the WD timeout is configured to 60 seconds.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed build error due to missing function prototype arch_misc_init] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes an issue which has been noticed on the Gardena board, with
the watchdog enabled, where the watdchdog reset (after a system hang)
did result in reporting of 2.9 GiB and a hang after this. With this
patch applied the memory controller is correctly reset and initialized
again even after a watchdog reset.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Mon, 8 Oct 2018 10:38:01 +0000 (12:38 +0200)]
gpio: Add MT7621 GPIO support
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned'] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
projects / u-boot.git / log
