Adam Ford [Sun, 9 Sep 2018 12:25:30 +0000 (07:25 -0500)]
ARM: am3517_evm: Enable Pinctrl
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Adam Ford [Sat, 8 Sep 2018 13:16:23 +0000 (08:16 -0500)]
mmc: omap_mmc: Remove invert references
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO] Signed-off-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:52 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:51 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:50 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:49 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:48 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:42 +0000 (10:35 +0300)]
board: atmel: add support for pda detection
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:41 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add onewire and eeprom drivers
SAMA5D4 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:40 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:39 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:38 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add onewire and eeprom drivers
SAMA5D3 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:37 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Maxime Ripard [Tue, 18 Sep 2018 07:35:25 +0000 (10:35 +0300)]
w1: Add 1-Wire gpio driver
Add a bus driver for bitbanging a 1-Wire bus over a GPIO.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: fixed some issues] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Maxime Ripard [Tue, 18 Sep 2018 07:35:24 +0000 (10:35 +0300)]
w1: Add 1-Wire uclass
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
doc: Add new doc for file system firmware loader driver model
Provide information about
- overview of file system firmware loader driver model
- describe storage device and partition in device tree source
- describe fie system firmware loader API
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
block: Add a function to find block device descriptor
Add a function to find the block device descriptor of the parent
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[trini: Move function declaration to avoid warning] Signed-off-by: Tom Rini <trini@konsulko.com>
cmd: ubifs: Factor out some checking codes into cmd_ubifs_mount()
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
cmd: ubifs: Move ubifs_initialized checking into cmd_ubifs_umount()
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 26 Sep 2018 19:14:02 +0000 (15:14 -0400)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h] Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Wed, 26 Sep 2018 12:07:41 +0000 (14:07 +0200)]
sandbox: Fix set_working_fdt_addr users
When running sandbox with the new pointer sanitization we just recently
introduced, we're running into a case with FIT images where we end up
interpreting pointers as addresses.
What happened is that most callers of set_working_fdt_addr() simply
convert pointers into addresses without taking into account that they
might be 2 separate address spaces. Fix the callers up to map their
pointers into addresses.
This patch modifies PL bitstream loading sequence as per
latest Xilfpga which supports all variants of bitstream images
generated from vivado and from bootgen. With this new change in
Xilfpga, uboot doesn't need to validate and swap bitstream as it will
be taken care inside Xilfpga. ZynqMP PL driver now checks for supporting
PMUFW version before skipping the validation and swap sequence as there
can be old PMUFW which doesn't supports this feature. In this case, driver
uses old way of PL bitstream loading sequence.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Return pmufw version for zynqmp_pmufw_version()
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bin Meng [Mon, 17 Sep 2018 05:35:28 +0000 (22:35 -0700)]
Makefile: Use -fno-strict-aliasing globally
The -fstrict-aliasing option is implicitly enabled at levels -O2,
-O3, -Os by GCC. This option allows the compiler to assume the
strictest aliasing rules applicable to the language being compiled.
For example, the practice of reading from a different union member
than the one most recently written to (called "type-punning") is
common. In this case, "type-punning" only works if the memory is
accessed through the union type, but might not work by taking the
address, casting the resulting pointer and dereferencing the result,
which is an undefined behavior per the "strict aliasing rules".
GCC's -Wstrict-aliasing (included in -Wall) option does not catch
all cases, but does attempt to catch the more common pitfalls. So
there are cases that GCC does not report but the codes are violating
the "strict aliasing rules".
Given lots of codes that may be written to rely on "type-punning",
and Linux kernel disables it by -fno-strict-aliasing globally, since
U-Boot currently does this on nds32/riscv/x86 builds only, extend
this for all architecture builds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tuomas Tynkkynen [Wed, 12 Sep 2018 22:28:54 +0000 (01:28 +0300)]
ata: ahci: Loop over the actual number of ports, not the maximum
The loop in ahci_start_ports() is looping over the maximum number of
SCSI devices in the system, which can be larger than the amount of ports
a particular AHCI controller has. The extra looping isn't directly
harmful because the link_port_map bitmap won't have the bit set for a
nonexistent port, but it is wasteful. Replace the loop limit with the
port count of the AHCI controller instead.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Sat, 8 Sep 2018 09:39:04 +0000 (21:39 +1200)]
Add include/asm-generic/atomic.h
The arm, xtensa and mips version of atomic.h were already very similar
(the mips one was a copy of xtensa). Combine these implementations
together to produce a generic atomic.h that can be included by these
architectures (and any others that need it in future).
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Adam Ford [Wed, 5 Sep 2018 09:11:08 +0000 (04:11 -0500)]
mmc: omap_hsmmc: Fix pbias for omap3_logic to enable CD pin
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Tom Rini [Fri, 31 Aug 2018 15:59:11 +0000 (11:59 -0400)]
dm: Update README.txt to clarify device tree usage
In the section about Device Trees add a paragraph at the end that
clarifies how we decide of a tree is valid or not. We say that all
bindings must either be in the specification (link provided) or in our
device-tree-bindings directory. We say that most of these come from the
Linux Kernel and as such some design decisions are made for us already,
but that in most cases we wish to retain compatibility.
Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sekhar Nori [Thu, 23 Aug 2018 11:41:31 +0000 (17:11 +0530)]
configs: am335x_evm: enable OF_BOARD_SETUP
Enable CONFIG_OF_BOARD_SETUP as it is needed for Beaglebone
black to overwrite the Ethernet phy address present in DT
in case the phy latches on to a different address.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Sekhar Nori [Thu, 23 Aug 2018 11:41:30 +0000 (17:11 +0530)]
board: ti: am335x: add support to fixup phy address
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Sekhar Nori [Thu, 23 Aug 2018 11:41:29 +0000 (17:11 +0530)]
drivers: net: cpsw: add support to update phy address
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:
configs: sama5d27_som1_ek: Add defconfig for ENV/boot from uSD
This adds a defconfig for sama5d27_som1_ek board to get environment from
uSD. The defconfig is made from sama5d27_som1_ek_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
uSD. The environment is expected to be found in uSD's FAT partition.
configs: sama5d2_xplained: Add defconfig for ENV/boot from eMMC
This adds a defconfig for sama5d2_xplained board to get environment from
eMMC. The defconfig is made from sama5d2_xplained_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
eMMC. The environment is expected to be found in eMMC's FAT
partition.
Marek Vasut [Tue, 14 Aug 2018 09:27:02 +0000 (11:27 +0200)]
spl: Weed out CONFIG_SYS_TEXT_BASE usage
The SPL loaders assume that the CONFIG_SYS_TEXT_BASE memory location
is available and can be corrupted by loading ie. uImage or fitImage
headers there. Sometimes it could be beneficial to load the headers
elsewhere, ie. if CONFIG_SYS_TEXT_BASE is not yet writable while we
still want to parse the image headers in some local onchip memory to
ie. extract firmware from that image.
Add the possibility to override the location where the headers get
loaded by introducing new function, spl_get_load_buffer() which takes
two arguments -- offset from the CONFIG_SYS_TEXT_BASE and size of the
data that are to be loaded there -- and returns a valid buffer address
or hangs the system. The default behavior is the same as before, add
the offset to CONFIG_SYS_TEXT_BASE and return that address. User can
override the weak spl_get_load_buffer() function though.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Create the handle of loaded images and the EFI_LOADED_IMAGE_PROTOCOL
inside efi_setup_loaded_image(). Do not use local variables.
Currently we expect the loaded image handle to point to the loaded image
protocol. Additionally we have appended private fields to the protocol.
With the patch the handle points to a loaded image object and the private
fields are added here. This matches how we handle the net and the gop
object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Sun, 23 Sep 2018 14:23:56 +0000 (16:23 +0200)]
efi_loader: Fix loaded_image handle passing from EL3
When running in EL3 mode on AArch64, we have to first drop to EL2
to execute a UEFI payload. When dropping down, the arguments to
the entry point have to stay identical to the ones for normal entry
though.
In commit ea54ad59286 ("efi_loader: pass handle of loaded image")
we incorrectly changed that logic and had the el3 entry path diverge.
Fix it up by syncing it back to what it's supposed to be.
Fixes: ea54ad59286 ("efi_loader: pass handle of loaded image") Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Since GRUB patch d0c070179d4d ("arm/efi: Switch to arm64 linux loader",
2018-07-09) we do not need a workaround for GRUB on 32bit ARM anymore.
So let's eliminate function efi_exit_caches().
This will require Linux distributions to update grub-efi-arm to the GRUB
git HEAD (a tag containing the aforementioned GRUB patch is not available
yet).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
CSI H can be used to position the cursor. The calling application may
specify a location that is beyond the limits of the screen. This may
lead to an illegal memory access.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we assign a lot of protocols to loaded images though
these protocols are not related to them. Instead they should be
installed on a separate handle. Via the device path it is the
parent to the devices like the network adapter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Not all terminals understand CSI [18t for querying the console size.
We should adhere to escape sequences documented in the console_codes
manpage and the ECMA-48 standard.
So here we follow a different approach. We position the cursor to the
bottom right and query its position. Before leaving the function we
restore the original cursor position.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Sun, 16 Sep 2018 15:05:29 +0000 (17:05 +0200)]
efi_loader: Merge memory map entries
We currently do not combine memory entries that are adjacent and have
the same attributes. The problem with that is that our memory map can
easily grow multiple hundreds of entries in a simple UEFI Shell
environment.
So let's make sure we always combine all entries to make the memory
map as small as possible. That way every other piece of code that
loops through it should also gain some nice speed ups.
projects / u-boot.git / log
