Pali Rohár [Thu, 11 Nov 2021 15:35:42 +0000 (16:35 +0100)]
pci: pci_mvebu: Move setup for BAR[0] where other BARs are setup
Function mvebu_pcie_setup_wins() sets up all other BARs, so move setup of
BAR[0] to this function to have common code at one place.
In the past, commit 193a1e9f196b ("pci: pci_mvebu: set BAR0 after memory
space is set") moved setup of BAR[0] to another location, due to ath10k
not working in kernel, but the reason why was unknown, but it seems to
work now, and we think the issue then was cause by the PCIe Root Port
presenting itself as a Memory Controller and therefore U-Boot's code
have overwritten the BAR. Since the driver now ignores any write
operations to PCIe Root Port BARs, this should not be an issue anymore.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
fw_setenv: Unbreak fw_setenv caused by buggy MEMISLOCKED use
Commit "fw_setenv: lock the flash only if it was locked before"
checks for Locked status with uninitialized erase data.
Address by moving the test for MEMISLOCKED.
Fixes: 8a726b852502 ("fw_setenv: lock the flash only if it was locked before") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Stefan Roese [Thu, 18 Nov 2021 08:18:41 +0000 (09:18 +0100)]
i2c: mvtwsi: Swab the register address if its size is > 1
Testing on Armada XP with an EEPROM using register address with size
of 2 has shown, that the register address bytes are sent to the I2C
EEPROM in the incorrect order. This patch swabs the address bytes so
that the correct address is transferred to the I2C device.
BTW: This worked without any issues before migrating Armada XP to
DM I2C.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Holland <samuel@sholland.org> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Pali Rohár <pali@kernel.org> Cc: Marek Behún <marek.behun@nic.cz> Tested-by: Marek Behún <marek.behun@nic.cz>
This is a backport from Marvell U-Boot:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell
commit 381d029e7a ("fix: serdes: a38x, a39x: Improve USB3 electrical
configuration")
- De-Emphasize force, in functional mode the transmitter should always
have 3.5db de-emphasize, so we are forcing it.
- After forcing De-Emphasize, choose 3.5db (After forcing, default is
6dB so need to change it to 3.5dB).
- Align90 set to 0x58 - this is the sample point in the receiver, after
the clock is recovered this sampler samples at the chosen value, usually
it is supposed to be 0x60(which is the center of the eye), but sometimes
after adding jitter and ISI the center of the eye can move slightly and
the sample point is not necessarily the exact center, and after
optimization (searching the middle of the eye manually) it was seen that
the center of the eye is actually 0x58 and not 0x60.
- FFE Res and FFE Cap set to 0xE & 0xF respectively: improves this
settings is adequate according to how the USB3 spec defines the
interconnect, thus improves USB3 jitter tolerance settings.
- Change the resolution of the DFE to 0x3 which is 6mV(highest
resolution) , this avoids the DFE to saturate and cease to work.
- HPF set to 0x3 which is 5Khz high pass filter, the function of the HPF
is to filter the low frequency patterns(below 5Khz) to make sure that
the signal is not a noise, the setting before was 0x1(205Khz), and the
change came since the USB3 CP0 pattern, that is used in the USB3 jitter
tolerance testing, is similar to PRBS15, which has 2^15=32768bits which
is 32768*200ps (200ps is one Unit interval in USB3(5Gbps)) = 6.5us,
which is in frequency terms: 152Khz. since the PRBS15 is a random
pattern and can theoretically have once in a while a pattern that will
be at frequency of 152Khz, hence the previous setting (205khz HPF) can
possibly filter this pattern which can cause to an error in the
receiver, thus this change to avoid such scenarios.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com> Signed-off-by: René Straub <rene.straub@netmodule.com> Reviewed-by: Stefan Roese <sr@denx.de>
arm: mvebu: a38x: serdes: fix serdes config for USB3
The electrical serdes configuration for USB3 expects an array as data
argument. For USB3 the second value is used (see data_arr_idx = USB3 =
1). However, because only one value is inside the array mv_seq_exec is
accessing an invalid element and the serdes is configured wrongly.
This wrong initialization is leading to an unreliable detection
mechanism for some USB3 devices. We were able to reproduce the issue
regularly with an LTE modem from Sierra Wireless (SM7455) where it was
not detected as USB3 device in 1/3 of all tests.
This commit fixes the issue by setting data_arr_idx to 0. This is the
same value as the original U-Boot from Marvell is using. There it is
called FIRST_CELL which is a define for 0.
See: https://github.com/MarvellEmbeddedProcessors/u-boot-marvell
commit 56f963ce4c ("fix: serdes: a38x, a39x: Fix USB3 serdes DB
initialization")
Signed-off-by: Stefan Eichenberger <eichest@gmail.com> Signed-off-by: René Straub <rene.straub@netmodule.com> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 26 Nov 2021 13:57:13 +0000 (14:57 +0100)]
phy: marvell: a3700: Convert to official DT bindings in COMPHY driver
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Konstantin Porotchkin <kostap@marvell.com> Cc: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Marcin Wojtas <mw@semihalf.com> Cc: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 26 Nov 2021 13:57:10 +0000 (14:57 +0100)]
fdt_support: Add some useful functions
Add functions
fdt_node_offset_by_pathf(),
fdt_create_phandle_by_pathf(),
fdt_set_status_by_pathf()
to get node offset, get/create node phandle and set status for node
given by path/alias formatted with sprintf.
Add functions
fdt_create_phandle_by_compatible(),
fdt_set_status_by_compatible()
to get/create node phandle and set status for first node given by
compatible.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 26 Nov 2021 13:57:07 +0000 (14:57 +0100)]
fdt_support: Remove fdt_alloc_phandle() in favor of fdt_generate_phandle()
Commit f0921f5098d ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: "hui.song" <hui.song_1@nxp.com> Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Behún [Fri, 26 Nov 2021 13:57:06 +0000 (14:57 +0100)]
treewide: Use fdt_create_phandle() where appropriate
Replace fdt_alloc_phandle() with subsequent fdt_set_phandle() by
fdt_create_phandle().
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Pali Rohár [Fri, 26 Nov 2021 13:57:05 +0000 (14:57 +0100)]
include/linux/byteorder: Fix compilation of __constant_cpu_to_be32()
The macro __constant_cpu_to_be32() uses ___constant_swab32(), which for
some reason is not defined and causes the following error during
compilation:
include/linux/byteorder/little_endian.h:28:52: warning:
implicit declaration of function ‘___constant_swab32’;
did you mean ‘__builtin_bswap32’? [-Wimplicit-function-declaration]
#define __constant_cpu_to_be32(x) ((__force __be32)___constant_swab32((x)))
Declare all ___constant_swabXX() macros.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
AKASHI Takahiro [Fri, 10 Dec 2021 06:49:36 +0000 (15:49 +0900)]
dm: fix an 'undefined' error in some macros
Due to a non-existing parameter name in macro's, use of those macro's will
cause a compiler error of "undefined reference".
Unfortunately, dm test doesn't fail because a wrong name ("&dev", hence it
is accidentally a valid name in the context of a caller site) is passed on.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Fixes: f262d4ca4b2b ("dm: core: Add a way to read platdata for all
child devices") Fixes: 903e83ee8464 ("dm: core: Add a way to iterate through children,
probing each") Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Fri, 10 Dec 2021 06:49:28 +0000 (15:49 +0900)]
part: call part_init() in blk_get_device_by_str() only for MMC
In blk_get_device_by_str(), the comment says: "Updates the partition table
for the specified hw partition."
Since hw partition is supported only on MMC, it makes no sense to do so
for other devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
The Calxeda servers are using U-Boot as the primary bootloader, which
was shipped as part of a firmware upgrade package.
Even though the machines are considered legacy at this point, the port
still works, so deserves some documentation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 8 Dec 2021 16:55:35 +0000 (09:55 -0700)]
fdtgrep: Handle an empty output tree
In strange cases it is possible for fdtgrep to find nothing to output.
Typically this means that the resulting SPL device tree is not going to
allow anything to boot, but at present the tree is actually invalid,
since it only has an END tag in the struct region.
The FDT spec requires at least a root node. So add a special case to
include at least this, if the FDT_REG_SUPERNODES flag is set.
This ensures that grepping an empty tree still produces a valid tree.
Also add comments to the enum since it is not completely obvious from
the names now.
The typical symptom of this problem is a message from binman:
Ivan Mikhaylov [Thu, 9 Dec 2021 16:10:53 +0000 (16:10 +0000)]
iot2050: binman: add missing-msg for blobs
Add the 'missing-msg' for blobs for more detailed output on missing system
firmware and SEBoot blobs.
Signed-off-by: Ivan Mikhaylov <ivan.mikhaylov@siemens.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Fix minor typos: Signed-off-by: Simon Glass <sjg@chromium.org>
Andy Shevchenko [Mon, 6 Dec 2021 11:44:13 +0000 (14:44 +0300)]
binman: Use less hard coded magic when inserting new PATH
Instead of joining hard coded '..' to the run-time path of the executable,
take just a dirname out of it. Besides that, use $(srctree) where it makes
sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Mon, 6 Dec 2021 11:44:12 +0000 (14:44 +0300)]
binman: Do not pollute source tree when build with `make O=...`
Importing libraries in Python caches the bytecode by default.
Since we run scripts in source tree it ignores the current directory
settings, which is $(srctree), and creates cache just in the middle
of the source tree. Move cache to the current directory.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simon Glass [Wed, 24 Nov 2021 04:08:59 +0000 (21:08 -0700)]
binman: Add support for ATF FIP
This format is used in firmware binaries so we may as well supported it.
With this patch binman supports creating, listing and updating FIPs, as
well as extracting files from one, provided that an FDTMAP is also present
somewhere in the image.
Tom Rini [Fri, 17 Dec 2021 12:25:34 +0000 (07:25 -0500)]
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Sun, 7 Nov 2021 15:08:55 +0000 (23:08 +0800)]
arm: socfpga: arria10: Reset MPFE NoC after program periph / combined RBF
This patch triggers warm reset to recover the MPFE NoC from corruption
due to high frequency transient clock output from HPS EMIF IOPLL at
VCO startup after peripheral RBF is programmed.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Sun, 7 Nov 2021 15:08:54 +0000 (23:08 +0800)]
arm: socfpga: arria10: Setting image magic value to romcode initswstate reg
The romcode_initswstate register need to be set with FSBL_IMAGE_IS_VALID
value if the current FSBL image is found valid, otherwise BootROM will
look for next subsequent valid FSBL image when warm reset is triggered.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com> Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Hari Prasath [Mon, 13 Dec 2021 05:00:03 +0000 (10:30 +0530)]
ARM: mach-at91: Add compile time option to choose proper timer
New SoC's of AT91 family with ARM-9 core includes a regular timer and a 64-bit
timer.This patch adds a compile time option to the Makefile such that the old
timer driver is chosen and compiled as default if none of timer configuration
options are explicitly defined in the board configs.
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com> Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Giulio Benetti [Sun, 14 Feb 2021 02:17:18 +0000 (03:17 +0100)]
clk: fix clk_get_rate() documentation
Improve clk_get_rate() @return documentation that otherwise is a bit
ambiguous. At the moment I expect to return 0 as error since the return
type is 'ulong', instead the function really returns negative value in
case the corresponding function pointer is null and returns 0 if the clock
is invalid.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
Pali Rohár [Thu, 11 Nov 2021 15:35:48 +0000 (16:35 +0100)]
arm: a37xx: pci: Do not allow setting ROM BAR on PCI Bridge
PCI Bridge which represents aardvark PCIe Root Port has Expansion ROM Base
Address register at offset 0x30 but its meaning is different than PCI's
Expansion ROM BAR register. Only address format of register is same.
In reality, this device does not have any configurable PCI BARs. So ensure
that write operation into BARs (including Expansion ROM BAR) is noop and
registers always contain zero address which indicates that bars are
unsupported.
Fixes: cb056005dc67 ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 11 Nov 2021 15:35:45 +0000 (16:35 +0100)]
pci: pci_mvebu: Do not allow setting ROM BAR on PCI Bridge
The PCI Bridge which represents mvebu PCIe Root Port has Expansion ROM
Base Address register at offset 0x30 but its meaning is different that
of PCI's Expansion ROM BAR register, although the address format of
the register is the same.
In reality, this device does not have any configurable PCI BARs. So
ensure that write operation into BARs (including Expansion ROM BAR) is a
noop and registers always contain zero address which indicates that BARs
are unsupported.
Fixes: a7b61ab58d5d ("pci: pci_mvebu: Properly configure and use PCI Bridge (PCIe Root Port)") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Vasut [Sat, 13 Nov 2021 02:27:37 +0000 (03:27 +0100)]
ARM: dts: stm32: Add custom PHY reset bindings on AV96
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Sat, 13 Nov 2021 02:26:39 +0000 (03:26 +0100)]
ARM: stm32: Fix SoM and board coding strap GPIO handling on DHSOM
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Sat, 13 Nov 2021 02:26:05 +0000 (03:26 +0100)]
ARM: stm32: Increase PHY auto-negotiation timeout to 20s on DHSOM
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Sat, 13 Nov 2021 02:25:13 +0000 (03:25 +0100)]
ARM: stm32: Add update_sf script to install U-Boot into SF on DHSOM
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Sat, 13 Nov 2021 02:24:44 +0000 (03:24 +0100)]
ARM: stm32: Increase USB power-good delay on DHSOM
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Hari Prasath [Wed, 8 Dec 2021 05:14:01 +0000 (10:44 +0530)]
ARM: mach-at91: update alternate function of signal PD20
The alternate function of PD20 is 4 as per the datasheet of
sama7g5 and not 5 as defined earlier.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5") Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com> Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Adam Ford [Mon, 6 Dec 2021 16:29:30 +0000 (10:29 -0600)]
configs: beacon-rzg2m: Config to address new aliases
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Adam Ford [Mon, 6 Dec 2021 16:29:29 +0000 (10:29 -0600)]
ARM: rmobile: Fix rzg2_beacon_defconfig to address new aliases
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This broke the reading/writing of the environmental variables,
so update the defconfig accordingly.
Adam Ford [Mon, 6 Dec 2021 16:29:28 +0000 (10:29 -0600)]
arm: dts: Create common rz-g2-beacon-u-boot file
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Adam Ford [Mon, 6 Dec 2021 16:29:26 +0000 (10:29 -0600)]
net: ravb: Support multiple clocks
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Tom Rini [Fri, 10 Dec 2021 12:58:43 +0000 (07:58 -0500)]
Merge tag 'efi-2022-01-rc4-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2022-01-rc4-2
UEFI:
* correctly handle missing TPM device
* prepare for block devices for U-Boot as EFI app
# gpg: Signature made Fri 10 Dec 2021 04:29:20 AM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Simon Glass [Sat, 4 Dec 2021 15:56:32 +0000 (08:56 -0700)]
efi: Add a media/block driver for EFI block devices
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Sat, 4 Dec 2021 15:56:30 +0000 (08:56 -0700)]
efi: Rename UCLASS_EFI and IF_TYPE_EFI
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Masahisa Kojima [Tue, 7 Dec 2021 05:15:33 +0000 (14:15 +0900)]
efi_loader: correctly handle no tpm device error
When the TCG2 protocol is installed in efi_tcg2_register(),
TPM2 device must be present.
tcg2_measure_pe_image() expects that TCP2 protocol is installed
and TPM device is available. If TCG2 Protocol is installed but
TPM device is not found, tcg2_measure_pe_image() returns
EFI_SECURITY_VIOLATION and efi_load_image() ends with failure.
The same error handling is applied to
efi_tcg2_measure_efi_app_invocation().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Tue, 7 Dec 2021 05:15:32 +0000 (14:15 +0900)]
efi_loader: check tcg2 protocol installation outside the TCG protocol
There are functions that calls tcg2_agile_log_append() outside
of the TCG protocol invocation (e.g tcg2_measure_pe_image).
These functions must to check that TCG2 protocol is installed.
If not, measurement shall be skipped.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit modify efi_tcg2_register() to return the
appropriate error.
With this fix, sandbox will not boot because efi_tcg2_register()
fails due to some missing feature in GetCapabilities.
So disable sandbox if EFI_TCG2_PROTOCOL is enabled.
UEFI secure boot variable measurement is not directly related
to TCG2 protocol installation, tcg2_measure_secure_boot_variable()
is moved to the separate function.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Fixes: d80162cfc559 ("doc: Document how to apply fdt overlays") Signed-off-by: Alexander Dahl <ada@thorsis.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Thu, 9 Dec 2021 13:43:30 +0000 (08:43 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
This fixes two regressions: eMMC operation on boards with WiFi (so using
three MMC devices), and a repeated wrong error message in USB gadget
mode (fastboot, ums).
Andre Przywara [Tue, 2 Nov 2021 19:45:47 +0000 (19:45 +0000)]
sunxi: Remove misleading USB-OTG charger message
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).
This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19b9)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================
Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 30 Nov 2021 23:18:54 +0000 (23:18 +0000)]
sunxi: dts: Fix typoed eMMC check
Commit 03510bf62149 ("sunxi: only include alias for eMMC when mmc2
used") protected the eMMC alias in U-Boot's DT stub the with the
associated Kconfig symbol, but was actually using the wrong name.
Fix the name of the symbol to match what's defined in Kconfig and what
the defconfig files actually use.
Fixes: 03510bf62149 ("sunxi: only include alias for eMMC when mmc2 used") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: 5kft@5kft.org Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tudor Ambarus [Wed, 3 Nov 2021 17:07:40 +0000 (19:07 +0200)]
ARM: dts: at91: sama7g5: Add QSPI0 and OSPI1 nodes
sama7g5 embedds an OSPI and a QSPI controller:
1/ OSPI0 Supporting Up to 200 MHz DDR. Octal, TwinQuad, Hyperflash
and OctaFlash Protocols Supported.
2/ QSPI1 Supporting Up to 90 MHz DDR/133 MHz SDR.
Tudor Ambarus [Wed, 3 Nov 2021 16:47:10 +0000 (18:47 +0200)]
spi: atmel-quadspi: Add support for SAMA7G5 QSPI
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
90 MHz DDR/133 MHz SDR
The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Mon, 6 Dec 2021 03:42:07 +0000 (22:42 -0500)]
Merge tag 'dm-pull-5dec21a' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
binman refactoring to improve section handling
bloblist - allow it to be allocated
sandbox config-header cleanup
# gpg: Signature made Sun 05 Dec 2021 10:14:24 PM EST
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
Simon Glass [Wed, 24 Nov 2021 16:26:46 +0000 (09:26 -0700)]
sandbox: Drop CONFIG_SYS_TIMER_RATE
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Simon Glass [Wed, 24 Nov 2021 16:26:39 +0000 (09:26 -0700)]
trace: sandbox: Use only the Kconfig options
At present there are Kconfig options for tracing, but sandbox uses
plain #defines to set them. Correct this and make the tracing command
default to enabled so that this is not needed.
projects / u-boot.git / log
