Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
Tom Rini [Fri, 3 Jan 2020 17:00:04 +0000 (12:00 -0500)]
Revert "mmc: davinci: drop struct davinci_mmc_plat"
Adam Ford reports that this change breaks booting on da850-evm and
Bartosz Golaszewski agrees that with the impending release we should
revert the change for now. With that noted:
Lokesh Vutla [Tue, 31 Dec 2019 10:19:55 +0000 (15:49 +0530)]
arm: mach-k3: Enable WA for R5F deadlock
On K3 devices there are 2 conditions where R5F can deadlock:
1.When software is performing series of store operations to
cacheable write back/write allocate memory region and later
on software execute barrier operation (DSB or DMB). R5F may
hang at the barrier instruction.
2.When software is performing a mix of load and store operations
within a tight loop and store operations are all writing to
cacheable write back/write allocates memory regions, R5F may
hang at one of the load instruction.
To avoid the above two conditions disable linefill optimization
inside Cortex R5F which will make R5F to only issue up to 2 cache
line fills at any point of time.
Lokesh Vutla [Tue, 31 Dec 2019 10:18:48 +0000 (15:48 +0530)]
arm: dts: k3-j721e: ddr: Update to 0.2 version of DDR config tool
Update the ddr settings to use the DDR reg config tool rev 0.2.0.
This reduces the aging count(in DDRSS_CTL_274_DATA reg) to 15 in-order
to avoid DSS underflow errors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Kevin Scholz <k-scholz@ti.com>
include/u-boot/crc.h: pull 'uint' definition on musl targets
The build failure was originally reported on arm64-musl
target at https://bugs.gentoo.org/703132. Here is the amd64-musl
variant:
```
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-only_defconfig -j$(nproc)
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-all -j$(nproc)
...
include/u-boot/crc.h:37:44: error: unknown type name 'uint'; did you mean 'int'?
37 | void crc16_ccitt_wd_buf(const uint8_t *in, uint len,
| ^~~~
| int
```
Note: 'uint' is not defined there.
On glibc 'uint' comes from <sys/types.h> and happens to work on most .c files.
The change imports 'uint' declaration from '<compiler.h>'.
Bug: https://bugs.gentoo.org/703132 Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
The build failure was originally reported on arm64-musl
target at https://bugs.gentoo.org/703132. Here is the amd64-musl
variant:
```
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-only_defconfig -j$(nproc)
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-all -j$(nproc)
...
In file included from tools/env/../../env/flags.c:7,
from tools/env/env_flags.c:1:
include/env.h:159:1: error: unknown type name 'ulong'; did you mean 'long'?
159 | ulong env_get_ulong(const char *name, int base, ulong default_val);
| ^~~~~
| long
```
Note: 'ulong' is not defined there.
On glibc 'ulong' comes from <sys/types.h>:
```c
/* Old compatibility names for C types. */
typedef unsigned long int ulong;
```
On musl it comes from <sys/types.h> as well but from under different guards:
```c
typedef unsigned long u_long, ulong;
```
The change inlines 'ulong' define similar to 'uint' define.
Bug: https://bugs.gentoo.org/703132 Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Tom Rini [Thu, 2 Jan 2020 15:28:26 +0000 (10:28 -0500)]
Merge tag 'u-boot-rockchip-20191231' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
Stephen Warren [Wed, 18 Dec 2019 18:37:21 +0000 (11:37 -0700)]
test_env: don't strip() printenv results
get_env() was originally written to strip() the output of printenv to
isolate the test from any whitespace changes in printenv's output.
However, this throws away any whitespace in the variable value, which can
cause issues when test code expects to see that whitespace. In fact,
printenv never adds any whitespace at all, so there's no need to strip.
The strip causes a practical problem for test_env_echo_exists() if
state_test_env.get_existent_var() happens to choose a U-Boot variable that
contains trailing whitespace. This is true for variable boot_targets.
With Python 2, get_existent_var() never returned boot_targets so this
issue never caused a practical problem.
With Python 3, get_existent_var does sometimes return boot_targets, no
doubt due to Python 3's different dict hash key order implementation,
about 0.5-2% of the time, so this test appears intermittent. With the
strip removed, this intermittency is solved, since the test passes for all
possible U-Boot variables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pankaj Bansal [Sat, 30 Nov 2019 13:14:10 +0000 (13:14 +0000)]
pci: layerscape: Manage PCIe EP compatible string via Kconfig
The ep node device tree name is governed by these bindings:
https://github.com/torvalds/linux/blob/master/Documentation/
devicetree/bindings/pci/layerscape-pci.txt#L24
As per above the ep compatible node contains platform name.
Therefore, define the ep node compatible as CONFIG to find the
pcie ep node in device tree during device tree fixup.
Pankaj Bansal [Sat, 30 Nov 2019 13:14:00 +0000 (13:14 +0000)]
pci: layerscape: move PCIE related CONFIG to PCI Kconfig
move the PCIE related config from arch Kconfig to PCI Kconfig.
As the PCI_LAYERSCAPE driver is being used in platform other than
fsl-layerscape platforms like ls102xa.
Patrik Dahlström [Sat, 21 Dec 2019 16:18:22 +0000 (17:18 +0100)]
omap3_beagle: Change NAND ECC scheme back to OMAP_ECC_HAM1_CODE_HW
The omap3_beagle NAND ECC scheme was changed in 4b37928d357 for unknown
reasons, leading to uncorrectible ecc errors. This commit changes it
back to what it was before.
Adam Ford [Sun, 3 Nov 2019 13:58:40 +0000 (07:58 -0600)]
ARM: imx6q_logic: Cleanup boot sequence check
The board_boot_order() function currenly assumes that the boot source
is MMC/eMMC, but this isn't true for the NAND devices.
This patch cleans up board_boot_order() to check for NAND, SD, ESD,
MMC or EMMC. Anything beyond these are not supported, so it will
default back to the serial downloader if any of those devices are not
available.
Fixes: 9fb50c68daa6 ("ARM: imx6q_logic: Fix MMC2 booting") Signed-off-by: Adam Ford <aford173@gmail.com>
Jagan Teki [Sat, 21 Dec 2019 07:54:30 +0000 (13:24 +0530)]
spi: rk: Limit transfers to (64K - 1) bytes
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Note, that the size is further divided into 'minus 1' while writing
into CTRLR1.
This change fixed two different read issues,
1. sf read failure when with > 0x10000
2. Boot from SPI flash failed during spi_flash_read call in
common/spl/spl_spi.c
Observed and Tested in
- Rockpro64 with Gigadevice flash
- ROC-RK3399-PC with Winbond flash
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Static checker warns 'ret' variable may be used uninitialized in
spi_nor_erase() and spi_nor_write() in case of zero length requests.
Fix these warnings by checking for zero length requests and returning
early.
Reported-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
When compile the curren mainline linux kernel(Linux 5.5-rc3)
with defconfig, the final Image is 29M, it's much
larger than Linux 5.4.
On the current u-boot side on rk3308, the gap between
kernel and fdt is 25M, the fdt will overwrite kernel
Image, so move ftd to a higher memory to give 34M
gab for them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thomas Hebb [Sat, 21 Dec 2019 02:05:22 +0000 (18:05 -0800)]
rockchip: add description for TPL_ROCKCHIP_COMMON_BOARD
SPL_ROCKCHIP_COMMON_BOARD, an almost identical option, has a title but
this one doesn't for some reason. Add a description to make the menu
easier to read.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 13 Dec 2019 09:41:17 +0000 (17:41 +0800)]
rockchip: px30-firefly add standalone dts
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Jack Mitchell [Tue, 10 Dec 2019 13:07:21 +0000 (13:07 +0000)]
rockchip: make_fit_atf: explicitly use python3
On a distribution with no python2 installed and no
python->python3 symlink the script will fail to execute.
Specify python3 explicitly as it's already a requirement
to build u-boot.
Signed-off-by: Jack Mitchell <ml@embed.me.uk> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Roger Quadros [Wed, 6 Nov 2019 14:21:17 +0000 (16:21 +0200)]
phy: ti-pipe3: improve DPLL stability for SATA & USB
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
Roger Quadros [Wed, 6 Nov 2019 14:21:15 +0000 (16:21 +0200)]
phy: ti-pipe3: Use TRM recommended settings for SATA DPLL
The AM572x Technical Reference Manual, SPRUHZ6H,
Revised November 2016 [1], shows recommended settings for the
SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings.
Use those settings in the driver. The TRM does not show
a value for 20MHz SYS_CLK so we use something close to the
26MHz setting.
Kever Yang [Thu, 5 Dec 2019 10:11:55 +0000 (18:11 +0800)]
rockchip: rk3288-evb: update config to support OPTEE
Upstream kernel and rockchip kernel has default enable PSCI which needs
OPTEE in trust word, enable OPTEE support for evb by default and SPL_FIT
option to pack OPTEE with U-Boot proper.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
And if enable the DEBUG for everyting in SPL, the log will hang at dwmmc
sending CMD16 for 'uboot' loadables binary because this step need a
large stack cost(about 0x2d00).
Kever Yang [Thu, 5 Dec 2019 10:11:52 +0000 (18:11 +0800)]
rockchip: fit_spl_optee: get text and optee base from build
Instead of hardcode the base address, we can get them from the build
output, eg. get the SYS_TEXT_BASE from .config and get optee base from
DRAM_BASE.
We can use this script for SoCs with DRAM base not from 0x60000000(rk3229
and many other 32bit Rockchip SoCs), eg. rk3288 DRAM base is 0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Wasim Khan [Fri, 15 Nov 2019 09:23:37 +0000 (09:23 +0000)]
pci: layerscape_gen4: Suffix API names with _ls_gen4
Update API names for layerscape gen4 fixup.
Suffix layerscape_gen4 fixup API names with _ls_gen4.
This is required to organize device tree fixup in common, layerscape
and layerscape_gen4 specific code.
Wasim Khan [Fri, 15 Nov 2019 09:23:32 +0000 (09:23 +0000)]
drivers/pci : enable pcie_layerscape code for lx2160a rev2
lx2160a rev1 uses pcie_layerscape_gen4 driver and lx2160a rev2 uses
pcie_layerscape driver.
Enable pcie_layerscape code for CONFIG_PCIE_LAYERSCAPE_GEN4.
Based on SoC and revision pcie controller probe will be invoked.
Current implementation to get board version through GPIO is
broken due to endianness issue hence it is not working for rev B
board.
Fix it to make it work for Rev A as well as Rev B boards
Alison Wang [Wed, 4 Dec 2019 06:21:55 +0000 (06:21 +0000)]
configs: Enable SPL_FSL_PBL for some LayerScape platforms
In commit <db4080d56dec>, SPL_FSL_PBL is removed from the configs of
some LayerScape platforms. Actually, SPL_FSL_PBL is needed for SD/NAND
boot on LS1021A/LS1043A/LS1046A to create boot binary having SPL binary
in PBI format concatenated with u-boot binary. SPL_FRAMEWORK is used on
these platforms too.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Alex Marginean [Wed, 27 Nov 2019 15:19:32 +0000 (17:19 +0200)]
ls1028a: Configure stream IDs for integrated PCI and fix up Linux DT
Hardware comes out of reset with implicit values, but these are outside
the accepted range for Layerscape gen 3 chassis spec used on LS1028A.
Allocate different IDs and fix up Linux DT to use them.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Ran Wang [Tue, 26 Nov 2019 03:40:40 +0000 (11:40 +0800)]
armv8: Add workaround for USB erratum A-050106
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
drivers/fsl-mc: Support DPSPARSER object and apply spb command
Add support for DPSPARSER object (create/destroy, open/close, apply spb)
which is required to configure Soft Parser by using MC.
Also add uboot command to apply Soft Parser Blob with command:
fsl_mc apply spb <spb_load_addr>
Tom Rini [Tue, 24 Dec 2019 13:18:19 +0000 (08:18 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
projects / u-boot.git / log
