Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:09 +0000 (17:01 +0800)]
mtd: spi-nor: Use spi-mem dirmap API
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Signed-off-by: Sean Anderson <seanga2@gmail.com> Acked-by: Pratyush Yadav <p.yadav@ti.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:08 +0000 (17:01 +0800)]
spi-mem: Add dirmap API from Linux
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Signed-off-by: Sean Anderson <seanga2@gmail.com> Acked-by: Pratyush Yadav <p.yadav@ti.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:07 +0000 (17:01 +0800)]
arm: dts: aspeed: Update SPI flash node settings
For both AST2500 and AST2600, there are three
SPI controllers, FMC(Firmware Memory Controller),
SPI1 and SPI2. The clock source is HCLK. Following
is the basic information for ASPEED SPI controller.
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:06 +0000 (17:01 +0800)]
spi: aspeed: Support AST2400 platform
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:04 +0000 (17:01 +0800)]
spi: aspeed: Add ASPEED SPI controller driver
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:03 +0000 (17:01 +0800)]
pinctrl: aspeed: FWSPICS1 and SPI1CS1 pin support
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Reviewed-by: Cédric Le Goater <clg@kaod.org>
Chin-Ting Kuo [Fri, 19 Aug 2022 09:01:02 +0000 (17:01 +0800)]
clk: aspeed: Get HCLK frequency support
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tom Rini [Tue, 13 Sep 2022 13:34:12 +0000 (09:34 -0400)]
Merge tag 'xilinx-for-v2023.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1
cmd:
- bdinfo - guard LMB code to run only when LMB is enabled
timer:
- convert arm twd timer to DM
power-domain:
- Skip loading config object for Versal
xilinx:
- Fix logic when dfu_alt_info is generated
- Define only mmc devnum not partition
- Add xlnx prefix to GEM compatible string
- Add missing tca6416 to zynqmp SC - vck190
- Add env redund offset
- Enable CMD_GREPENV/SETEXPR by default
- Move board_get_usable_ram_top() to common location
- Add support for SOC detection
net/gem:
- Check rate before setting it up
microblaze:
- drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
- Show cache size in bdinfo
spi:
- cadence_qspi: driver updates
- zynqmp_gqspi: driver updates
- zynqmp_gqspi: Add tap delays for Versal
zynq:
- Enable mkeficapsule compilation
- Use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME for dfu_alt_info
- Align bss and end of u-boot image to 64bits
- Align qspi node name with Linux kernel
- DT: List OCM memory
zynqmp:
- Fix AES cache handling with a user provided key
- SOM: Add mtd partition for secure OS storage area
- Add ref_clk property for REFCLKPER calculation
- Fix mdio bus description for vck190-sc
Tom Rini [Tue, 13 Sep 2022 12:59:11 +0000 (08:59 -0400)]
Merge branch '2022-09-12-update-pytests-for-more-parellel-support' into next
To quote the author:
This series makes a further attempt to get closer to having all tests
run in parallel. It introduces a new 'make pcheck' option which runs
tests in parallel, skipping those that are not compatible.
A number of fixes are included for existing tests. The vboot test is
updated to only run a single scenario in 'quick' mode.
This makes use of pytest's parallel-testing features. The resulting
times (including incremental building with LTO) on a 16-core machine are
as follows:
make pcheck - 1 minute 6 seconds
make qcheck - 3 minutes
make check - 5 minutes 15 seconds
Note that this is not a fair comparison, since 'make pcheck' omits a
number of tests, even more than 'make qcheck'.
Michal Simek [Tue, 6 Sep 2022 10:40:41 +0000 (12:40 +0200)]
xilinx: common: Add support for SOC detection
Code supports board detection based on information available in EEPROM in
legacy or FRU format. But this is not enough for emulation and simulation
systems which are lacking these identification EEPROMs. But SOC itself has
normally registers for SOC identification. Based on them it is possible to
compose detected name. That's why prepare infrastructure in common location
for SOC platform detection which is called before board platform detection.
SOC platform detection shouldn't detect real silicon and should fallback to
current existing mechanism to identify boards based on EEPROMs.
spi: zynqmp_gqspi: Fix issue of reading more than 32bits length
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Michal Simek [Thu, 25 Aug 2022 12:59:02 +0000 (06:59 -0600)]
arm64: versal: Define zynqmp_mmio_write() for versal
GQSPI driver is using it but this function is never called for Versal
because it is removed by linker. But function should be declared to avoid
this build warning:
drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay':
drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function
'zynqmp_mmio_write' [-Wimplicit-function-declaration]
378 | zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST,
spi: cadence-qspi: Use priv instead of plat across the driver
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
spi: cadence-qspi: Correct flash reset function name
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Ovidiu Panait [Mon, 29 Aug 2022 17:02:04 +0000 (20:02 +0300)]
cmd: bdinfo: introduce bdinfo_print_size() helper
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Ovidiu Panait [Mon, 29 Aug 2022 17:02:03 +0000 (20:02 +0300)]
cpu: microblaze: add error handling in microblaze_cpu_get_desc()
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Michal Simek [Tue, 6 Sep 2022 10:41:34 +0000 (12:41 +0200)]
xilinx: versal: Disable LMB for mini configurations
There shouldn't be a reason to have LMB on for these configurations.
LMB was already disabled for ZynqMP by commit 0063487a5b60 ("configs:
zynqmp: Disable LMB for mini u-boot").
Michal Simek [Thu, 25 Aug 2022 12:23:10 +0000 (14:23 +0200)]
arm64: xilinx: Move board_get_usable_ram_top() to common location
The commit ce39ee28ec31 ("zynqmp: Do not place u-boot to reserved memory
location") adds functionality for ZynqMP to read reserved memory node and
do not place U-Boot to reserved location. This functionality is generic
across all Xilinx SOCs that's why move it to common location to be used by
all Xilinx SOCs.
On zynq platform this is also fixing issue where U-Boot was placed to
locating which was reserved already which ends up with error message
"ERROR: reserving fdt memory region failed (addr=30000000 size=10000000
flags=4)" which is shown when bdinfo is called.
Tested on vck190, zcu102, zc706 and kc705 to cover all platforms.
Michal Simek [Wed, 31 Aug 2022 09:28:59 +0000 (11:28 +0200)]
ARM: zynq: Align bss and end of u-boot image to 64bits
The main reason is that DT memory reserved code is expecting DT to be 64bit
aligned. For more information take a look at commit 5bd5ee02b23b ("xilinx:
zynqmp: Check that DT is 64bit aligned").
T Karthik Reddy [Wed, 24 Aug 2022 11:23:26 +0000 (13:23 +0200)]
xilinx: Add env redund offset
ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env
variables is overwriting data at 0 offset, which is wrong. So add default
redund env offset for Zynq, ZynqMP, Versal and microblaze platforms.
Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE).
In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead
of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000.
Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of
ENV_IS_IN_SPI_FLASH config.
Below table specifies platform specific env and env redund offsets.
Piyush Mehta [Tue, 23 Aug 2022 13:03:31 +0000 (15:03 +0200)]
arm64: zynqmp: add ref_clk property for REFCLKPER calculation
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ
calculation. This property configure correct value for SOF/ITP counter
and period of ref_clk.
This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores.
Harini Katakam [Tue, 23 Aug 2022 12:59:20 +0000 (14:59 +0200)]
arm: dts: Add xlnx prefix to GEM compatible string
cdns,zynq/zynqmp were recentle deprecated in Linux in favour of xlnx
prefix. Add this new compatible string and retain the existing string for
compatibility with uboot drivers.
arm64: zynqmp: Add mtd partition for secure OS storage area
Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Michal Simek [Tue, 9 Aug 2022 14:32:54 +0000 (16:32 +0200)]
xilinx: Define only mmc devnum not partition
The commit 53b406369e9d ("DFU: Check the number of arguments and argument
string strictly") added strict control over string that 0:1 partition
definition is not valid anymore that's why use only device number without
partition ID. Device is specified by 2nd parameter and partition by 3rd.
Simon Glass [Sat, 6 Aug 2022 23:51:59 +0000 (17:51 -0600)]
Makefile: Add a pcheck option to run tests in parallel
Running tests in parallel is much faster, e.g. 15 seconds to run the tests
on sandbox (only), instead of 100 seconds (on a 16-core machine). Add a
'make pcheck' option to access this feature.
Note that the tools/ tests still run each tool's tests once after the
other, although within that, they do run in parallel. So for example,
the buildman tests run in parallel, then the binman tests run in
parallel. There would be a signiificant advantage to running them all
in parallel together, but that would require a large amount of
refactoring, e.g. with more use of pytest fixtures.
Update the documentation to represent the current state.
Simon Glass [Sat, 6 Aug 2022 23:51:57 +0000 (17:51 -0600)]
test/py: Support --build when running tests in parallel
At present when -n is used, all workers try to build U-Boot at once.
Add a lock to ensure that only one of them builds, with the others using
the build that is produced.
Simon Glass [Sat, 6 Aug 2022 23:51:54 +0000 (17:51 -0600)]
test: Make test_gpio_read() independent
This assumes that the GPIO starts as 0 but it does not if
test_gpio_input() ran first and test_gpio_exit_statuses() was skipped.
This can happen when running tests in parallel.
This test relies on the silent_linux env variable being set. Add this
to the code so it can run without relying on other bootm tests having been
run first.
Michal Simek [Tue, 6 Sep 2022 10:41:10 +0000 (12:41 +0200)]
xilinx: zynq: Disable LMB for mini configurations
There shouldn't be a reason to have LMB on for these configurations.
LMB was already disabled for ZynqMP by commit 0063487a5b60 ("configs:
zynqmp: Disable LMB for mini u-boot").
Michal Simek [Wed, 7 Sep 2022 07:52:09 +0000 (09:52 +0200)]
cmd: bdinfo: Enable dumping lmb data when LMB is enabled
The commit 9996cea75f5a ("lmb/bdinfo: dump lmb info via bdinfo") added
support for dumping LMB information as the part of bdinfo. But code itself
should be called only when LMB is enabled.
fpga: zynq: Remove post config info message for SPL
The drivers informs the user that a post config was not run after FPGA
configuration. This message is unnecessary in SPL because the
ps7_post_config function is called via spl_board_prepare_for_boot
function before jump_to_image_no_args function from board_init_r
function.
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Tom Rini [Sat, 3 Sep 2022 01:51:21 +0000 (21:51 -0400)]
Merge branch '2022-09-02-assorted-improvements' into next
- DM RTC improvements that should help in CI, allow disabling LTO from
the make line, add extension (cape, etc) support to distro bootcmd,
add a pause command and re-enable ARM v4T support.
Simon Glass [Mon, 1 Aug 2022 13:58:48 +0000 (07:58 -0600)]
dm: rtc: Try to handle the localtime() race
At present the sandbox timer uses localtime() which can jump around twice
a year when daylight-saving time changes.
It would be tricky to make use of gmtime() since we still need to present
the time in local time, as seems to be required by U-Boot's RTC interface.
The problem can only happen once, so use a loop to detect it and try
again. This should be sufficient to detect either a change in the 'second'
value, or a daylight-saving change. We can assume that the latter also
incorporates a 'second' change, so there is no need to loop more than
twice.
Simon Glass [Mon, 1 Aug 2022 13:58:46 +0000 (07:58 -0600)]
dm: rtc: Avoid a race in the rtc_reset test
Since resetting the RTC on sandbox causes it to read the base time from
the system, we cannot rely on this being unchanged since it was last read.
Allow for a one-second delay.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Fixes: https://source.denx.de/u-boot/u-boot/-/issues/4 Reported-by: Bin Meng <bmeng.cn@gmail.com> Reported-by: Tom Rini <trini@konsulko.com> Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 3 Aug 2022 18:13:08 +0000 (12:13 -0600)]
Makefile: Allow LTO to be disabled for a build
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Sergei Antonov [Sun, 21 Aug 2022 13:34:20 +0000 (16:34 +0300)]
arm: ARMv4 assembly compatibility
There is currently a problem that U-Boot can not work on ARMv4
because assembly imlementations of memcpy() and some other functions
use "bx lr" instruction that is not available on ARMv4 ("mov pc, lr"
should be used instead).
A working preprocessor-based solution to this problem is found in
arch/arm/lib/relocate.S. Move it to the "ret" macro in
arch/arm/include/asm/assembler.h and change all "bx lr" code
to "ret lr" in functions that may run on ARMv4. Linux source code
deals with this problem in the same manner.
v1 -> v2:
Comment update. Pointed out by Andre Przywara.
Signed-off-by: Sergei Antonov <saproj@gmail.com> CC: Samuel Holland <samuel@sholland.org> CC: Ye Li <ye.li@nxp.com> CC: Simon Glass <sjg@chromium.org> CC: Andre Przywara <andre.przywara@arm.com> CC: Marek Vasut <marex@denx.de> CC: Sean Anderson <sean.anderson@seco.com> CC: Tom Rini <trini@konsulko.com>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com> Cc: Simon Glass <sjg@chromium.org>
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the
SPL to build cache-pl310.c.
Before this commit, the SPL could enable the PL310 L2 cache [1], but the
cache maintenance functions from cache-pl310.c were only useable for
non-SPL builds.
After enabling the cache one must be able to flush it, too. Thus this
commit allows cache-pl310.c to be included in the SPL build.
[1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable()
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Tom Rini [Wed, 10 Aug 2022 14:29:28 +0000 (10:29 -0400)]
Remove CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS et al
This removes the following symbols:
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS
CONFIG_SYS_I2C_LDI_ADDR
CONFIG_SYS_I2C_DVI_ADDR
CONFIG_SYS_I2C_DVI_BUS_NUM
Andrew Davis [Tue, 26 Jul 2022 01:25:06 +0000 (20:25 -0500)]
firmware: ti_sci: Move ACK checking to ti_sci_do_xfer() function
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Andrew Davis [Tue, 26 Jul 2022 01:25:05 +0000 (20:25 -0500)]
firmware: ti_sci: Remove inline keyword from functions
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Andrew Davis [Tue, 26 Jul 2022 01:25:03 +0000 (20:25 -0500)]
firmware: ti_sci: Reduce output on ti_sci_do_xfer error
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
arm: dts: qcom: Sync pinctrl DT nodes with Linux bindings
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Sumit Garg [Thu, 4 Aug 2022 14:27:20 +0000 (19:57 +0530)]
board: qcs404-evb: Enable USB3 specific PMIC GPIO
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Sumit Garg [Thu, 4 Aug 2022 14:27:18 +0000 (19:57 +0530)]
gpio: qcom_pmic: Add support for GPIO LV/MV subtype
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Sumit Garg [Thu, 4 Aug 2022 14:27:17 +0000 (19:57 +0530)]
pmic: Convert pm8916 driver to a generic Qcom PMIC driver
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Sumit Garg [Thu, 4 Aug 2022 14:27:16 +0000 (19:57 +0530)]
dts: qcs404-evb: Add USB controller and PHY nodes
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
projects / u-boot.git / log
