Becky Bruce [Mon, 4 Aug 2008 19:02:26 +0000 (14:02 -0500)]
POWERPC 86xx: Move BAT setup code to C
This is needed because we will be possibly be locating
devices at physical addresses above 32bits, and the asm
preprocessing does not appear to deal with ULL constants
properly. We now call write_bat in lib_ppc/bat_rw.c.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
Bitmaps with odd-numbered width won't be rendered
correctly and even U-Boot crashes are observed on
some platforms while repeated rendering of such
bitmaps with "bmp display". Also if a bitmap is
rendered to an odd-numbered x starting position,
the same problem occurs. This patch is an attempt
to fix it.
If logo_plot() should ever be called with x starting
position other than zero and for pixel depths greater
than 8bpp, logo colors distortion will be observed.
This patch fixes the issue.
While locally preparing some U-Boot patches for ARM based OMAP3 boards, some
using OneNAND and some using NAND, we found some differences in OneNAND and
NAND command address handling.
As this might confuse users (it already confused us), we like to align OneNAND
and NAND address handling.
The issue is that cmd_onenand.c subtracts the onenand base address from the
addresses you type into the u-boot command line so, unlike nand, you can't
use addresses relative to the start of the onenand part e.g. this won't work:
The commit was based on a misunderstanding of the (documented)
meaning of the 'autostart' environment variable. It might cause
boards to hang if 'autostart' was used, with the potential to brick
them. Go back to the documented behaviour.
Wolfgang Denk [Fri, 8 Aug 2008 14:41:56 +0000 (16:41 +0200)]
TQM8xxL: fix support for second flash bank
When switching the TQM8xxL modules to use the CFI flash driver,
support for the second flash bank was broken because the CFI driver
did not support dynamically sized banks. This gets fixed now.
Wolfgang Denk [Fri, 8 Aug 2008 14:39:54 +0000 (16:39 +0200)]
CFI: allow for dynamically determined flash sizes and addresses
The CFI driver allowed only for static initializers in the
CFG_FLASH_BANKS_LIST definition, i. e. it did not allow to map
several flash banks contiguously if the bank sizes were not known in
advance, which kind of violates U-Boot's design philosophy.
Steven A. Falco [Wed, 6 Aug 2008 19:42:52 +0000 (15:42 -0400)]
ppc4xx: Sequoia has two UARTs in "4-pin" mode. Configure the GPIOs as per schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com> Signed-off-by: Stefan Roese <sr@denx.de>
John Rigby [Tue, 5 Aug 2008 23:38:57 +0000 (17:38 -0600)]
mpc5121: squash some fdt fixup errors
On ADS5121 when booting linux the following errors are seen:
Unable to update property /soc5121@80000000:bus-frequency, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:local-mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /soc5121@80000000/ethernet@2800:address, err=FDT_ERR_NOTFOUND
This is caused by ft_cpu_setup trying to deal with
both old and new soc node naming. This patch
fixes this by being smarter about what to
fixup.
Also do soc node fixups by compatible instead of by path.
A new board config called OF_SOC_COMPAT defined
to be "fsl,mpc5121-immr" replaces the old
OF_SOC node path that was defined to be "soc@80000000".
Old device trees still work, but the compatiblity
is conditional on CONFIG_OF_SUPPORT_OLD_DEVICE_TREES
which is on by default in include/configs/ads5121.h.
Mark Jackson [Fri, 1 Aug 2008 08:48:29 +0000 (09:48 +0100)]
Fix bitmap display for atmel lcd controller
The current lcd_display_bitmap() function does not work properly
for the Atmel LCD controller.
2 fixes need to be done:-
(a) when setting the colour map, use the lcd_setcolreg() function
as provided by the Atmel driver
(b) the data is never actually written to the lcd framebuffer !!
Wolfgang Denk [Wed, 16 Jul 2008 14:38:59 +0000 (16:38 +0200)]
Fix printf() format problems with configurable prompts
U-Boot allows for configurable prompt strings using the
CONFIG_AUTOBOOT_PROMPT resp. CONFIG_MENUPROMPT definitions. So far,
the assumption was that any such user defined problts would contain
exactly one "%d" format specifier. But some boards did not.
To allow for flexible boot prompts without adding too complex code we
now allow to specify the whole list of printf() arguments in the user
definition. This is powerful, but requires a responsible user who
really understands what he is doing, as he needs to know for exanple
which variables are available in the respective context.
Kumar Gala [Wed, 30 Jul 2008 19:13:30 +0000 (14:13 -0500)]
mpc85xx: Update linker scripts for Freescale boards
* Move to using absolute addressing always. Makes the scripts a bit more
portable and common
* Moved .bss after the end of the image. These allows us to have more
room in the resulting binary image for code and data.
* Removed .text object files that aren't really needed
* Make sure _end is 4-byte aligned as the .bss init code expects this.
(Its possible that the end of .bss isn't 4-byte aligned)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 30 Jul 2008 13:01:15 +0000 (08:01 -0500)]
Fix compile warnings in dlmalloc
The origional code was using on odd reference to get to the first
real element in av_[]. The first two elements of the array are
not used for actual bins, but for house keeping. If we are more
explicit about how use the first few elements we can get rid of the
warnings:
dlmalloc.c: In function 'malloc_extend_top':
dlmalloc.c:1971: warning: dereferencing type-punned pointer will break strict-aliasing rules
dlmalloc.c:1999: warning: dereferencing type-punned pointer will break strict-aliasing rules
dlmalloc.c:2029: warning: dereferencing type-punned pointer will break strict-aliasing rules
...
The logic of how this code came to be is:
bin_at(0) = (char*)&(av_[2]) - 2*SIZE_SZ
SIZE_SZ is the size of pointer, and av_ is arry of pointers so:
bin_at(0) = &(av_[0])
Going from there to bin_at(0)->fd or bin_at(0)->size should be straight forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Stefan Roese [Wed, 30 Jul 2008 07:59:51 +0000 (09:59 +0200)]
cmd_bootm.c: Fix problem with '#if (CONFIG_CMD_USB)'
A recent patch used '#if (CONFIG_CMD_USB)' instead of
'#if defined(CONFIG_CMD_USB)'. This patch fixes this problem and makes
common/bootm.c compile again.
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Markus Klotzbuecher <mk@denx.de>
Kumar Gala [Tue, 29 Jul 2008 17:23:49 +0000 (12:23 -0500)]
fsl_i2c: Use timebase timer functions instead of get_timer()
The current implementation of get_timer() is only really useful after we
have relocated u-boot to memory. The i2c code is used before that as part
of the SPD DDR setup.
We actually have a bug when using the get_timer() code before relocation
because the .bss hasn't been setup and thus we could be reading/writing
a random location (probably in flash).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Frank Svendsbøe [Tue, 29 Jul 2008 12:49:31 +0000 (14:49 +0200)]
Adder8xx: Fix CFG_MONITOR_LEN
Due to increased space usage, U-Boot can no longer be stored in three sectors.
The current U-Boot use just over three flash sectors (197k), and U-Boot will
become corrupt after saving environment variables. This patch adds another 64k
to CFG_MONITOR_LEN.
Signed-off-by: Frank E. Svendsbøe <frank.svendsboe@gmail.com>
Because the cmd_tbl_s structure depends on the configuration file, it
must be assured that config.h is included before the structure is
evaluated by the compiler. If this is not certain, it could happen
that the compiler generates structures of different size, depending
on the fact if the source file includes <config.h> before or after
<command.h>.
The effect is that u-boot crashes when tries to relocate the command
table (for ppc) or try to access to the command table for other
architectures.
The problem can happen on board-depending commands. All general
commands under /common are unaffected, because they include already
config.h before command.h.
cmd_ide.c:827: Warnung: weak declaration of `ide_outb' after first use results in unspecified behavior
cmd_ide.c:839: Warnung: weak declaration of `ide_inb' after first use results in unspecified behavior
Adrian Filipi [Tue, 22 Jul 2008 18:28:11 +0000 (14:28 -0400)]
Removed support for the adsvix board.
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
ARM: set GD_FLG_RELOC for boards skipping relocation to RAM
If CONFIG_SKIP_RELOCATE_UBOOT is set the flag GD_FLG_RELOC is usually
never set, because relocation to RAM is actually never done by U-boot
itself. However, several pieces of code check if this flag is set at
some time.
So, to make sure this flag is set on boards skipping relocation, this
is added to the initialisation of U-boot at a moment where it is safe
to do so.
Timur Tabi [Mon, 21 Jul 2008 19:26:23 +0000 (14:26 -0500)]
fsl-i2c: fix writes to data segment before relocation
Prevent i2c_init() in fsl_i2c.c from writing to the data segment before
relocation. Commit d8c82db4 added the ability for i2c_init() to program the
I2C bus speed and save the value in i2c_bus_speed[], which is a global
variable. It is an error to write to the data segment before relocation,
which is what i2c_init() does when it stores the bus speed in i2c_bus_speed[].
projects / u-boot.git / log
![16 years agoRevert "[new uImage] Add autostart flag to bootm_headers structure"](/img/sics.gif?p=u-boot.git;a=commit;h=0bf202ec586d4466c900e987720fa635c594d689){kind=link}
