When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
allow opting out of WATCHDOG_RESET() from timer interrupt
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
timer: mpc83xx_timer: fix build with CONFIG_{HW_, }WATCHDOG
The code, which is likely copied from arch/powerpc/lib/interrupts.c,
lacks a fallback definition of CONFIG_SYS_WATCHDOG_FREQ and refers to
a non-existing timestamp variable - obviously priv->timestamp is
meant.
Some boards don't work with the rate-limiting done in the generic
watchdog_reset() provided by wdt-uclass.
For example, on powerpc, get_timer() ceases working during bootm since
interrupts are disabled before the kernel image gets decompressed, and
when the decompression takes longer than the watchdog device
allows (or enough of the budget that the kernel doesn't get far enough
to assume responsibility for petting the watchdog), the result is a
non-booting board.
As a somewhat hacky workaround (because DT is supposed to describe
hardware), allow specifying hw_margin_ms=0 in device tree to
effectively disable the ratelimiting and actually ping the watchdog
every time watchdog_reset() is called. For that to work, the "has
enough time passed" check just needs to be tweaked a little to allow
the now==next_reset case as well.
Andre Przywara [Sat, 17 Apr 2021 21:55:19 +0000 (22:55 +0100)]
sunxi: DT: A64: Update devicetree files from Linux 5.12
Import updated devicetree files from the Linux v5.12 release.
Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.
This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 15 Apr 2021 23:53:17 +0000 (00:53 +0100)]
net: sun8i-emac: Fix pinmux setup for Allwinner H5
Commit eb5a2b671075 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2 Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sat, 3 Apr 2021 23:10:15 +0000 (01:10 +0200)]
ARM: rmobile: Enable CONFIG_SYS_FLASH_PROTECTION
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 25 Apr 2020 12:57:45 +0000 (14:57 +0200)]
clk: renesas: Only ever access documented bits in clock driver teardown
The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.
Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 24 Apr 2021 23:39:14 +0000 (19:39 -0400)]
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
Tom Rini [Sat, 24 Apr 2021 17:30:57 +0000 (13:30 -0400)]
Merge tag 'video-2021-07-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-video
- search for additional detailed timings in the EDID extension block
- rework sunxi DE2 driver and accompanying DW-HDMI platform driver
to drop redundant device specific code, and later use the DT as a
source of information
video: sunxi: de2: switch to public uclass functions
Currently DE2 driver uses functions which are defined in internal
headers. They are not meant to be used outside of uclass framework.
Switch DE2 driver to public ones. This has additional benefit that
device_probe doesn't need to be called manually.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is no real need to read source_id at probe time. It also doesn't
make sense to store it in driver private data since it's already stored
in class platform data. While this looks like cleanup (and it is), it's
also important for DE2 driver rework because this info will be filled
later (after probe is already executed).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are two ways how hot plug detection can be done.
One is standard way for DW HDMI controller - checking bit 2 in 0x3004
register. Another way is applicable only to Allwinner custom PHY - by
checking bit 19 in register 0x10038. Both methods are equally good as
far as we know.
Use standard method in order to reduce amount of custom code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
common: edid: Search for valid timing in extension block
One of my monitors have only 4k@60 timing in base EDID block which is
out of range for devices with HDMI 1.4. It turns out that it has
additional detailed timings in CTA-861 Extension Block and two of them
are appropriate for HDMI 1.4.
Add additional search for valid detailed timing in extension block.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
common: edid: extract code for detailed timing search
Code which searches for valid detailed timing entry will be used in more
places. Extract it.
No functional change is made. However, descriptors are casted to
edid_detailed_timing instead of edid_monitor_descriptor. Descriptor can
be of either type, but since we're interested only in DTD, it is more
fitting to cast to edid_detailed_timing.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
commit cbea241e935e("efidebug: add multiple device path instances on Boot####")
slightly tweaked the efidebug syntax adding -b, -i and -s for the boot
image, initrd and optional data.
The pytests using this command were adapted as well. However I completely
missed the last "" argument, which at the time indicated the optional data
and needed conversion as well. This patch is adding the missing -s flag
and the tests are back to normal.
Fixes: cbea241e935e("efidebug: add multiple device path instances on Boot####") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: capsule: return a correct error code at find_boot_device()
In case of failure at efi_get_variable_int("BootOrder"), we should
skip examining boot option variables and return an appropriate error
code which is the one the function returned.
Bumping the digest list count, for all supported algorithms, can be
calculated outside of the individual switch statements. So let's do that
for every loop iteration instead and simplify the code a bit.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Marek Vasut [Sun, 11 Apr 2021 16:30:36 +0000 (18:30 +0200)]
doc: imx: psb: Fix missing setexpr arguments
Due to copy-paste error, two of the setexpr arguments were missing.
Add the missing arguments.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Aaron Williams [Wed, 7 Apr 2021 07:12:39 +0000 (09:12 +0200)]
mips: octeon: dts/dtsi: Change UART DT node to use clocks property
We already have a clock driver for MIPS Octeon. This patch changes the
Octeon DT nodes to supply the clock property via the clock driver
instead of using an hard-coded value, which is not correct in all cases.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:36 +0000 (09:12 +0200)]
scsi: Add ata_swap_buf_le16() to support big-endian platforms
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:35 +0000 (09:12 +0200)]
ata: ahci: Fix usage on big-endian platforms
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:34 +0000 (09:12 +0200)]
sata: ahci_mvebu.c: Enable AHCI/SATA driver for MIPS Octeon
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:33 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Enable AHCI/SATA support
For easy AHCI/ SATA integration, this patch adds board_ahci_enable()
for the MVEBU AHCI driver, which will be used by this platform. This
platform specific "enable" function will setup the proper endian
swapping in the AHCI controller so that it can be used by the common
AHCI code.
Additionally the endian swizzle entry for AHCI in
octeon_should_swizzle_table[] is removed, as this enabled the original
lowlevel code function, e.g. octeon_configure_qlm(), for the QLM setup
to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:32 +0000 (09:12 +0200)]
mips: octeon: cpu.c: Add arch_misc_init() for pci-console & pci-bootcmd
This patch adds the necessary platform infrastructure code, so that the
MIPS Octeon drivers "serial_octeon_pcie_console" & "serial_bootcmd" can
be used. This is e.g. the bootmem initialization in a compatible way to
the Marvell 2013 U-Boot, so that the exisiting PC remote tools like
"oct-remote-console" & "oct-remote-load" can be used. This is be done in
the newly introduced arch_misc_init(), which calls the necessary init
functions when enabled.
These patches are in preparation for the MIPS Octeon NIC23 board
support, which is a desktop PCIe target board enabling these features.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:31 +0000 (09:12 +0200)]
serial: serial_octeon_bootcmd.c: Add PCI remote console support
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:30 +0000 (09:12 +0200)]
serial: serial_octeon_pcie_console.c: Add PCI remote console support
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Stefan Roese [Wed, 7 Apr 2021 07:12:29 +0000 (09:12 +0200)]
mips: octeon: cvmx-coremask.h: Fix cvmx_coremask_dprint() with DEBUG defined
As DEBUG is no Kconfig symbol, we can't use the IS_ENABLED() macros.
This patch switches to the unfortunately necessary #ifdef usage again
to make it work correctly.
Stefan Roese [Fri, 11 Dec 2020 16:06:12 +0000 (17:06 +0100)]
mips: octeon: octeon_ebb7304_defconfig: Enable Octeon PCIe and E1000
This patch changes the MIPS Octeon defconfig to enable some features
for PCIe enablement. This includes CONFIG_BOARD_LATE_INIT to call the
board specific serdes init code.
With these features enabled, the serdes and PCIe driver including the
Intel E1000 driver can be tested on the Octeon EBB7304.
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Aaron Williams [Fri, 11 Dec 2020 16:06:10 +0000 (17:06 +0100)]
mips: octeon: octeon_ebb7304: Add board specific QLM init code
This patch adds the board specific QLM/DLM init code to the Octeon 3 EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 11 Dec 2020 16:06:07 +0000 (17:06 +0100)]
mips: octeon: Makefile: Enable building of the newly added C files
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Aaron Williams [Fri, 11 Dec 2020 16:06:02 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper.c
Import cvmx-helper.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:06:01 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper-util.c
Import cvmx-helper-util.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:06:00 +0000 (17:06 +0100)]
mips: octeon: Add cvmx-helper-jtag.c
Import cvmx-helper-jtag.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:59 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-helper-fdt.c
Import cvmx-helper-fdt.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:58 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-helper-cfg.c
Import cvmx-helper-cfg.c from 2013 U-Boot. It will be used by the later
added drivers to support PCIe and networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 11 Dec 2020 16:05:56 +0000 (17:05 +0100)]
mips: octeon: Misc changes required because of the newly added headers
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Aaron Williams [Fri, 23 Apr 2021 17:56:32 +0000 (19:56 +0200)]
mips: octeon: Add misc remaining header files
Import misc remaining header files from 2013 U-Boot. These will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Aaron Williams [Fri, 11 Dec 2020 16:05:54 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sso-defs.h header file
Import cvmx-sso-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:53 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sriox-defs.h header file
Import cvmx-sriox-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-sriomaintx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:51 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-smix-defs.h header file
Import cvmx-smix-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:50 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sli-defs.h header file
Import cvmx-sli-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:49 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-sata-defs.h header file
Import cvmx-sata-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:48 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-rst-defs.h header file
Import cvmx-rst-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:47 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pow-defs.h header file
Import cvmx-pow-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:46 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pko-defs.h header file
Import cvmx-pko-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:45 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pki-defs.h header file
Import cvmx-pki-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:44 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pip-defs.h header file
Import cvmx-pip-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:43 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pepx-defs.h header file
Import cvmx-pepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:42 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pemx-defs.h header file
Import cvmx-pemx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:41 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pcsx-defs.h header file
Import cvmx-pcsx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:40 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pciercx-defs.h header file
Import cvmx-pciercx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:39 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-pcieepx-defs.h header file
Import cvmx-pcieepx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:38 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-npi-defs.h header file
Import cvmx-npi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:37 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-mio-defs.h header file
Import cvmx-mio-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:36 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-l2c-defs.h header file
Import cvmx-l2c-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:35 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-ipd-defs.h header file
Import cvmx-ipd-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:34 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-gserx-defs.h header file
Import cvmx-gserx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:33 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-gmxx-defs.h header file
Import cvmx-gmxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:32 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-fpa-defs.h header file
Import cvmx-fpa-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:31 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dtx-defs.h header file
Import cvmx-dtx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:30 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dpi-defs.h header file
Import cvmx-dpi-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:29 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-dbg-defs.h header file
Import cvmx-dbg-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:28 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-ciu-defs.h header file
Import cvmx-ciu-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:27 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-bgxx-defs.h header file
Import cvmx-bgxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:26 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-asxx-defs.h header file
Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:25 +0000 (17:05 +0100)]
mips: octeon: Add cvmx-agl-defs.h header file
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Aaron Williams [Fri, 11 Dec 2020 16:05:24 +0000 (17:05 +0100)]
mips: octeon: Add misc cvmx-helper header files
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log
