The kmnusa board uses a mv88e6352 switch that is connected to the main
eth interface of the kirkwood. Therefore the switch must be configured
so that the kirkwood's egiga eth inferface can be used.
Simon Baatz [Fri, 20 Jul 2012 09:59:14 +0000 (09:59 +0000)]
kirkwood: ib62x0: Invert SATA activity LEDs
The hardware design of the IB-NAS62x0 causes the SATA activity
LEDs to be on when idle by default. Reverse the polarity of the
activity LEDs in early init.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Cc: Luka Perkov <uboot@lukaperkov.net> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Luka Perkov <uboot@lukaperkov.net>
Size of the SDRAM chips might differ between any two (otherwise
identical) instances of the same board.
So add a function kw_sdram_size_adjust() which reads out the current
ram size for a given bank, and adjusts the Kirkwood's SDRAM window size
register accordingly.
Some boards might be equipped with different SDRAM configurations.
When that is the case, CPU CS Window Size Register (CS[0]n Size)
should be set to the biggest value through board.cfg file; then its
value can be fixed at runtime according to the detected SDRAM size.
Signed-off-by: Luka Perkov <uboot@lukaperkov.net> Tested-by: Wojciech Dubowik <wojciech.dubowik@neratec.com> Tested-by: Tim Fletcher <tim@night-shade.org.uk>
Simon Guinot [Thu, 6 Sep 2012 10:51:42 +0000 (10:51 +0000)]
ARM: add support for Network Space v2 Lite and Mini
This patch adds support for the LaCie boards Network Space v2 (Lite and
Mini). This two boards are derived from the Network Space v2 and a lot
of hardware caracteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports (Lite only): host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Rmobile common timer driver diverts the same driver as SH architecture.
When it builds at the same place with source, it is no problem, but when
it builds out of source, it cannot build.
This patch revises this problem.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
arm: rmobile: kzm9g: Add CONFIG_GLOBAL_TIMER to board config file
kzm9g board use global timer. But by commit 813ffda31, timer function of
rmobile was changed that global timer might be used, when CONFIG_GLOBAL_TIMER
was defined.
This add CONFIG_GLOBAL_TIMER to board config file.
arm: rmobile: kzm9g: separate cpu_rev to integer and fraction
According to SoC document, revision info is separated to integer part and
fracton part.
So I separete rmobile_get_cpu_rev() to rmobile_get_cpu_rev_integer() and
rmobile_get_cpu_rev_fraction().
The value of CONFIG_BAUDRATE is treated as string and put as initial value of
environment variable. If it begin with '(', it is wrongly parsed to 0 in number.
So I removed '(' and ')'.
Latest rmobile code was tested by using old gcc (gcc-4.4).
When we use gcc-4.6 (or later), the build is made, but does not work.
This solves a problem not to work by add -march=armv5 to compiple option
when we built in gcc-4.6 (or later).
I tested by linaro's compiler version 2012.04-20120426.
arm: rmobile: kzm9g: Modify bus controller setting for CS4
Problem:
Linux kernel hangs up when it write a file to NFS mounted directory.
Solution:
Modify bus controller setting for CS4, which connected smsc9221 ethernet
controller.
Detail:
Modify CS4BCR bit[29:28] (IWW[1:0]) from 00 to 01.
Modify CS4BCR bit[20:19] (IWRRD[1:0]) from 00 to 01.
Modify CS4BCR bit[17:16] (IWRRS[1:0]) from 00 to 01.
Modify CS4WCR bit[27:26] (WSW[1:0]) from 10 to 11
Modify CS4WCR bit[25:24] (WHW[1:0]) from 01 to 10
Modify CS4WCR bit[18:16] (WW[2:0]) from 101 to 111
Modify CS4WCR bit[13:11] (SW[2:0]) from 010 to 011
Modify CS4WCR bit[10:7] (WR[3:0]) from 1000 to 1011
am335x-evm config: decrease bootdelay to 1s and mount rootfs RO
A fast boot is important to the beaglebone, so save 2 seconds here by
decreasing bootdelay. This is still plenty time to break into the prompt,
I do that at least once a day.
Mount the rootfs RO by default, this is needed to make fsck succeed
without resorting to an initramfs.
Joel A Fernandes [Tue, 18 Sep 2012 04:30:51 +0000 (04:30 +0000)]
am33xx: Fix fetching of mmc1 bootmode from bootrom for AM33XX
U-boot should not ignore getting the bootmode passed on from the bootrom.
With this, U-boot SPL knows it was loaded from MMC1 and use this info to
read full U-boot from MMC1 as well.
Cc: pprakash@ti.com Cc: trini@ti.com Signed-off-by: Joel A Fernandes <joelagnel@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@ti.com>
Vendor Class Identifier option is common to BOOTP and DHCP and
can be useful without PXE. So send VCI in both BOOTP and DHCP
requests if CONFIG_BOOTP_VCI_STRING is defined.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> Signed-off-by: Tom Rini <trini@ti.com>
Commit cfda5aeab89d73779e26f0d34cf10f64caa67431
(cmd_fat: use common get_device_and_partition function)
introduced a warning:
cmd_fat.c: In function 'do_fat_fswrite':
cmd_fat.c:178:8: warning: unused variable 'ep' [-Wunused-variable]
Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Lei Wen [Fri, 28 Sep 2012 04:26:45 +0000 (04:26 +0000)]
lib: zlib: remove the limitation for cannot using 0 as start
We often need the requirement that compressing those memory range start
from 0, but the default deflate code in zlib prevent us to do this.
Considering the special case of uboot, that it could access all memory
range, it is reasonable to be able to also take the address space from 0
into compression.
Pavel Herrmann [Thu, 27 Sep 2012 23:18:03 +0000 (23:18 +0000)]
remove unnecessary code in ata_piix
We set sata_curr_device to 0 right after returning from init_sata(), so there's
no point in setting it to the last scanned driver at this point.
Note: there are more duplicities with cmd_sata, but those might be required,
as the code seems to reset the entire controller on every scan, ignoring the
requested port number.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Stephen Warren [Fri, 28 Sep 2012 05:34:09 +0000 (05:34 +0000)]
disk: allow - or empty string to fall back to $bootdevice
Commit 10a37fd "disk: get_device_and_partition() "auto" partition"
prevented the use of "-" on the command-line to request fallback to the
$bootdevice environment variable instead. This patch allows that, or an
empty string "" to be used.
Tom Rini [Mon, 27 Aug 2012 21:58:28 +0000 (14:58 -0700)]
SPL: Rework how we inform about un-headered images
First, remove the puts from the case where we don't have an mkimage
header as this is somewhat common and intentional for no-arg target
images. Second, rework the final switch statement in board_init_r to,
in the case of !CONFIG_SPL_OS_BOOT be only about doing debug prints
about if we know what the magic is or not (the CONFIG_SPL_OS_BOOT case
is unchanged). Then we call jump_to_image_no_args(). This gives us the
same behavior as before but with slightly smaller code.
Stefan Roese [Tue, 28 Aug 2012 08:50:59 +0000 (10:50 +0200)]
SPL: Enable use of custom defined U-Boot entry point
By setting CONFIG_SYS_UBOOT_START boards can now use a different entry
point for their U-Boot image. So the U-Boot entry point is not fixed
to CONFIG_SYS_TEXT_BASE any more.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Mon, 27 Aug 2012 10:50:58 +0000 (12:50 +0200)]
SPL: Add option to skip copying of the mkimage header
On some system (e.g. powerpc), the load-address and entry-point is
located at address 0. So the current approach to load the image
(payload) including the header to the address "load-address - 64"
can't work here.
This patch adds an flag to skip this copying including header to
the SPL framework. By setting SPL_COPY_PAYLOAD_ONLY, only the
playload will be copied. This will be used by the SPL NOR flash
driver on powerpc.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Mon, 27 Aug 2012 10:50:59 +0000 (12:50 +0200)]
SPL: Add NOR flash booting support
SPL NOR flash booting support is quite simple. Only copying of the
images is needed.
On MPC5xxx we need to make sure to only use the standard memcpy()
implementation and not the MPC5xxx specific one. As the MPC5xxx
version has some complexity which is not needed for this SPL
booting.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 20 Aug 2012 16:31:52 +0000 (09:31 -0700)]
da850: Add README.da850
This file documents when to build for da850evm and when to build for
da850_am18xxevm. It also documents how to write the u-boot.ais file to
persistent storage (such as SPI), in some cases as well as how to write
a recovery image.
Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Sughosh Ganu [Mon, 27 Aug 2012 19:23:37 +0000 (00:53 +0530)]
hawkboard: Update config file to work with common spl framework
The common spl framework expects the u-boot payload size through
CONFIG_SYS_MONITOR_LEN. Define the macro with the u-boot's size. With
this change, CONFIG_SYS_NAND_U_BOOT_SIZE is no longer required. Delete
the same.
Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tom Rini [Tue, 14 Aug 2012 19:27:13 +0000 (12:27 -0700)]
ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORK
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Some DHCP servers (notably dnsmasq) always transmit DHCP Option 28,
Broadcast Address as specified in RFC 2132. Without this patch u-boot
displays the warning:
*** Unhandled DHCP Option in OFFER/ACK: 28
The patch suppresses the warning and ignores DHCP Option 28. There is
no environment variable to set the broadcast address into and if for
some reason u-boot needs the broadcast it can be calculated from
ipaddr and netmask.
Now DT support is becoming common for all new SoC's. Hence it is better
to have option for getting specific FDT from the remote server.
This patch adds support for new label i.e. 'fdt'. This will allow to
retrieve 'fdt blob' from the remote server. This patch take care for
the following scenarios.
The usage of fdt is optional.
The 'fdt blob' can be retrieved from tftp or can be available locally
or can be absent.
If 'fdt_addr_r' environment variable is set and 'fdt' label is defined
retrieve 'fdt blob' from tftp. 'fdt_addr_r' is then passed along bootm
command.
If 'fdt_addr' is set and 'fdt blob' is not retrieved from the tftp pass
'fdt_addr' to bootm command. In this case 'fdt blob' will be available
at 'fdt_addr'.
If 'fdt_addr' is not set and 'fdt blob' is not retrieve from tftp pass
NULL to boot command. In this case 'fdt blob' is not required and absent.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
Marek Vasut [Wed, 29 Aug 2012 03:49:50 +0000 (03:49 +0000)]
FEC: Rework the TX wait mechanism
The mechanism waiting for transmission to finish in fec_send() now
relies on the E-bit being cleared in the TX buffer descriptor. In
case of data cache being on, this means invalidation of data cache
above this TX buffer descriptor on each test for the E-bit being
cleared.
Apparently, there is another way to check if the transmission did
complete. This is by checking the TDAR bit in the X_DES_ACTIVE
register. Reading a register does not need any data cache invalidation,
which is beneficial.
Rework the sequence that wait for completion of the transmission so that
the TDAR bit is tested first and afterwards check the E-bit being clear.
This cuts down the number of cache invalidation calls to one.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 29 Aug 2012 03:49:49 +0000 (03:49 +0000)]
FEC: Remove endless loop in the FEC driver
The FEC hardware sometimes errors out on data transfer and hangs in
the tightloop adjusted by this patch. So add timeout into the tightloop
to make such a hang recoverable.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Sun, 26 Aug 2012 10:19:21 +0000 (10:19 +0000)]
FEC: Properly align address over the buffers for cache ops
Align the address that's to be invalidated/flushed properly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Benoit Thebaudeau <benoit.thebaudeau@advans> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Sun, 26 Aug 2012 10:19:20 +0000 (10:19 +0000)]
FEC: Do not pass unaligned buffer to network stack
Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Benoit Thebaudeau <benoit.thebaudeau@advans> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the 88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
projects / u-boot.git / log
