Tom Rini [Thu, 6 Jun 2013 12:57:45 +0000 (08:57 -0400)]
am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>
The location of valid scratch space is dependent on SoC, so move that
there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On
am33xx/ti814x we want to use what the ROM defines as "public stack"
which is the area after our defined download image space. Correct the
comment about and location of CONFIG_SPL_TEXT_BASE.
Tom Rini [Fri, 31 May 2013 16:31:59 +0000 (12:31 -0400)]
am33xx/omap: Move save_omap_boot_params to omap-common/boot-common.c
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 31 May 2013 14:48:03 +0000 (10:48 -0400)]
am33xx: Correct NON_SECURE_SRAM_START/END
Prior to Sricharan's cleanup of the boot parameter saving code, we
did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a
problem that the address was pointing to the middle of our running SPL.
Correct to point to the base location of the download image area.
Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being
used. As part of correcting these tests, make use of the fact that
we've always been placing our stack outside of the download image area
(which is fine, once the downloaded image is run, ROM is gone) so
correct the max size test to be the ROM defined top of the download area
to where we link/load at.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Fix typo noted by Peter Korsgaard
Stephen Warren [Tue, 14 May 2013 08:02:56 +0000 (08:02 +0000)]
fdt: allow bootdelay to be specified via device tree
This can be useful to force bootcmd to execute as soon as U-Boot has
started.
My use-case is: An SoC-specific tool pushes U-Boot into RAM, along with
an image to be written to device boot flash, with the DT config property
"bootcmd" set to contain a command to write that image to flash. In this
scenario, we don't want to allow any stale bootdelay value taken from
the current flash content to affect how long it takes before the
flashing process starts.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Stephen Warren [Thu, 23 May 2013 12:09:57 +0000 (12:09 +0000)]
input: simplify key_matrix_decode_fdt()
We know the exact property names that the code wants to process. Look
these up directly with fdt_get_property(), rather than iterating over
all properties within the node, and checking each property's name, in
a convoluted fashion, against the expected name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 22 May 2013 08:48:18 +0000 (08:48 +0000)]
input: fix unaligned access in key_matrix_decode_fdt()
Initialized character arrays on the stack can cause gcc to emit code that
performs unaligned accessess. Make the data static to avoid this.
Note that the unaligned accesses are made when copying data to prefix[] on
the stack from .rodata. By making the data static, the copy is completely
avoided. All explicitly written code treats the data as u8[], so will never
cause any unaligned accesses.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 21 May 2013 21:08:09 +0000 (21:08 +0000)]
common: board_f: Do not call board_postclk_init twice
The generic-board board_init_f function called board_postclk_init twice.
The first one came from arch/arm/lib/board.c, while the second one
from arch/powerpc/lib/board.c.
This commit deletes the first occurrence.
In addition, the second get_clocks call is moved after
board_postclk_init in order to keep the function call order
both for ARM and PowerPC.
ARM board calles get_clocks function after board_postclk_init.
Marek Vasut [Sun, 19 May 2013 12:53:34 +0000 (12:53 +0000)]
disk: Fix possible out-of-bounds access in part_efi.c
Make sure to never access beyond bounds of either EFI partition name
or DOS partition name. This situation is happening:
part.h: disk_partition_t->name is 32-byte long
part_efi.h: gpt_entry->partition_name is 36-bytes long
The loop in part_efi.c copies over 36 bytes and thus accesses beyond
the disk_partition_t->name .
Fix this by picking the shortest of source and destination arrays and
make sure the destination array is cleared so the trailing bytes are
zeroed-out and don't cause issues with string manipulation.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 16 May 2013 13:53:23 +0000 (13:53 +0000)]
image: Use fit_image_load() to load FDT
Use the new common code to load a flat device tree. Also fix up a few casts
so that this code works with sandbox. Other than that the functionality
should not change.
Simon Glass [Thu, 16 May 2013 13:53:21 +0000 (13:53 +0000)]
image: Introduce fit_image_load() to load images from FITs
At present code to load an image from a FIT is duplicated in the three
places where it is needed (kernel, fdt, ramdisk).
The differences between these different code copies is fairly minor.
Create a new function in the fit code which can handle any of the
requirements of those cases.
Simon Glass [Thu, 16 May 2013 13:53:20 +0000 (13:53 +0000)]
mkimage: Add map_sysmem() and IH_ARCH_DEFAULT to simplfy building
These are not actually used in mkimage itself, but the image code (which
is common with mkimage) does use them. To avoid #ifdefs in the image code
just for mkimage, define dummy version of these here. The compiler will
eliminate the dead code anyway.
A better way to handle this might be to split out more things from common.h
so that mkimage can include them. At present any file that mkimage uses
has to be very careful what headers it includes.
Simon Glass [Thu, 16 May 2013 13:53:19 +0000 (13:53 +0000)]
bootstage: Introduce sub-IDs for use with image loading
Loading a ramdisk, kernel or FDT goes through similar stages. Create
a block of IDs for each task, and define a consistent numbering within
the block. This will allow use of common code for image loading.
Simon Glass [Wed, 15 May 2013 06:23:55 +0000 (06:23 +0000)]
main: Separate out the two abortboot() functions
There are two implementations of abortboot(). Turn these into two separate
functions, and create a single abortboot() which calls either one or the
other.
Also it seems that nothing uses abortboot() outside main, so make it static.
At this point there is no further use of CONFIG_MENU in main.c.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Wai-Hong Tam [Fri, 12 Apr 2013 11:04:37 +0000 (11:04 +0000)]
tpm: Reorganize the I2C TPM driver
This patch does a similar code reogranzation from
http://patchwork.ozlabs.org/patch/132179/
which is based on an old version of code (fdt support and bus selection
still not in). It merges this tidy-up on top of the recent code. It does
not make any logical change.
tpm.c implements the interface defined in tpm.h based on underlying
LPC or I2C TPM driver. tpm.c and the underlying driver communicate
throught tpm_private.h.
Note: Merging the LPC driver with tpm.c is left to future patches.
Change-Id: Ie1384f5f9e3935d3bc9a44adf8de80c5a70a5f2b Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Vincent Palatin [Fri, 12 Apr 2013 11:04:36 +0000 (11:04 +0000)]
tpm: Add support for new Infineon I2C TPM (SLB 9645 TT 1.2 I2C)
Add support for Infineon's new SLB 9645 TT 1.2 I2C TPMs,
which supports clockstretching, combined reads and a bus speed of
up to 400khz. The device also has a new device id.
This is based on the kernel patch provided by Infineon :
https://gerrit.chromium.org/gerrit/42332
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Luigi Semenzato <semenzato@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Vincent Palatin <vpalatin@chromium.org> Tested-by: Tom Wai-Hong Tam <waihong@chromium.org> Tested-by: Vincent Palatin <vpalatin@chromium.org>
The new name is more aligned with Linux kernel's naming of TPM driver.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Wai-Hong Tam <waihong@chromium.org>
Sergey Lapin [Mon, 14 Jan 2013 03:46:50 +0000 (03:46 +0000)]
mtd: resync with Linux-3.7.1
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
Albert ARIBAUD [Sun, 19 May 2013 01:48:15 +0000 (01:48 +0000)]
arm: factorize relocate_code routine
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Fri, 17 May 2013 14:10:14 +0000 (14:10 +0000)]
ARM: tegra: support SKU 1 of Tegra114
Make U-Boot aware of the Tegra114 SKU 1, and treat it identically
to any other Tegra114.
This value is used on (at least some) Dalmore boards with a production
rather than engineering chip. Such boards are in the hands of some
partners who want to use upstream U-Boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 14 May 2013 08:00:53 +0000 (08:00 +0000)]
tegra: always build u-boot-nodtb-tegra.bin
Even when eventually building u-boot-dtb-tegra.bin, separately building
u-boot-nodtb-tegra.bin can be useful, since building it encapsulates the
SPL padding step. If you want to tweak u-boot.dtb and regenerate
u-boot-dtb-tegra.bin, it is then a simple cat operation.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Allen Martin [Fri, 10 May 2013 16:56:55 +0000 (16:56 +0000)]
Tegra: clk: always use find_best_divider() for periph clocks
When adjusting peripheral clocks always use find_best_divider()
instead of clk_get_divider() even when a secondary divider is not
available. In the case where is requested clock is too slow to be
derived from the parent clock this allows a best effort to get close
to the requested clock.
This comes up for commands like "sf" where the user can pass a clock
speed on the command line or "sspi" where the clock is hardcoded to
1MHz, but the Tegra114 SPI controller can't go that low.
Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Ruchika Gupta [Mon, 25 Mar 2013 07:40:25 +0000 (07:40 +0000)]
SECURE BOOT - Removed deletion of TLB entries code
Boot ROM code creates TLB entries for 3.5G space before entering
the u-boot. Earlier we were deleting these entries after early
initialization of CPU. In recent past, code has been added
to invalidate all these entries before relocation of u-boot code.
So this code to delete TLB entries after CPU initialization
is no longer required.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Acked-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Mon, 25 Mar 2013 07:40:21 +0000 (07:40 +0000)]
powerpc/p5040: fix mdio mux for 10G port
Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in
eth port enum structure, it will assign mdio mux depend on this assumption.
This is not true with Fman V3, which added more 1G ports after port DTSEC5
in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux.
So we use dynamic index for 10G ports instead of hardcoded enum value
when doing mdio mux for 10G ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Poonam Aggrwal [Mon, 25 Mar 2013 07:40:20 +0000 (07:40 +0000)]
powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.h
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.
Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Xie Xiaobo [Mon, 25 Mar 2013 07:40:19 +0000 (07:40 +0000)]
sf: spansion: Add support for S25FL128S
SPANSION recommend S25FL128S supersedes S25FL129P, and the two flash
memory have the same device ID and Memory architecture. So they can
use the same config parameters.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Mon, 25 Mar 2013 07:40:18 +0000 (07:40 +0000)]
powerpc/p2041: fix serdes reference clock frequency display for PC board
PC board has different serdes clock setting with PB board, it uses same
serdes frequency setting on bank2 as on bank1. PC board can be distingushed
from PB board by checking CPLD version, if running on PC board, then fix
the serdes reference clock frequency of bank2.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaveta Leekha [Mon, 25 Mar 2013 07:40:17 +0000 (07:40 +0000)]
powerpc/b4860: fix for Serdes connectivity to SFP's
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shengzhou Liu [Mon, 25 Mar 2013 07:40:15 +0000 (07:40 +0000)]
powerpc/t4240qds: fix PHY reset timeout issue
QSGMII card has different PHY address against previous SGMII card.
We check the type of card in slots and set correct PHY address to
avoid complainning "PHY reset timed out" during u-boot booting up.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Suresh Gupta [Mon, 25 Mar 2013 07:40:13 +0000 (07:40 +0000)]
Enable XAUI interface for B4860QDS
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Ed Swarthout [Mon, 25 Mar 2013 07:40:10 +0000 (07:40 +0000)]
powerpc/t4qds: use clock measurement for sysclk and ddr clock
Use QIXIS measurement registers to obtain sysclk and ddr clock. This
allows using non-standard clock speeds, set by directly writing to
clock chip or store the values in qixis clock data eeprom.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Ed Swarthout [Mon, 25 Mar 2013 07:40:09 +0000 (07:40 +0000)]
powerpc/qixis: add clock measurement registers
QIXIS includes frequency measurement functions for each major processor
clock input. After reset (and after clocks are stable), QIXIS measures
the clocks against a reference frequency and stores the results in
CLK_FREQ registers. A base register supplies a multiplier which allows
directly obtaining the measured value, without requiring knowledge of
the target system or QIXIS core frequency.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 25 Mar 2013 07:40:08 +0000 (07:40 +0000)]
powerpc/mpc8xxx: Allow DDR overclock
Allow DDR clock runs faster than SPD specifes. This may cause memory
failure, but the user should know what is going to happen when using
higher than expected DDR clock.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 25 Mar 2013 07:40:07 +0000 (07:40 +0000)]
powerpc/chassis2: Change core numbering scheme
To align with chassis generation 2 spec, all cores are numbered in sequence.
The cores may reside across multiple clusters. Each cluster has zero to four
cores. The first available core is numbered as core 0. The second available
core is numbered as core 1 and so on.
Core clocks are generated by each clusters. To identify the cluster of each
core, topology registers are examined.
Cluster clock registers are reorganized to be easily indexed.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 25 Mar 2013 07:40:06 +0000 (07:40 +0000)]
powerpc/mpc8xxx: Add T1040 and variant SoCs
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis
Generation 2. The major difference between T1040 and its variants is the
number of cores and the number of L2 switch ports.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 25 Mar 2013 07:40:01 +0000 (07:40 +0000)]
powerpc/t4240qds: Add VDD override
Allow VDD voltage overriding with a command. This is an add-on feasture of
VID. To override VDD, use command vdd_override with the value of voltage
in mV, for example
vdd_override <voltage in mV, eg. 1050>
The above example will set the VDD to 1.050 volt. Any wrong value out of
range of 0.8188 to 1.2125 volt or invalid string is ignored.
In addition to the command, if overriding VDD is needed earlier in booting
process, save an variable and reboot:
setenv t4240qds_vdd_mv <voltage in mV>
saveenv
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Shaohui Xie [Mon, 25 Mar 2013 07:39:59 +0000 (07:39 +0000)]
net/phy: fix select line for TN80xx
TN80xx has same PHY ID as TN2020, but it needs different setting to register
30.93 which used to select line, so we read register 30.32 which has
bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2,
for TN80xx we will get 5 or 4.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Mon, 25 Mar 2013 07:39:24 +0000 (07:39 +0000)]
powerpc/t4240qds: Add board detail for bdinfo command
Print more detail information including core voltage, RCW source, switch
settings, etc. with bdinfo command.
Signed-off-by: York Sun <yorksun@freescale.com> CC: Wolfgang Denk <wd@denx.de> CC: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Masahiro Yamada [Mon, 20 May 2013 21:08:08 +0000 (21:08 +0000)]
cmd_mem: fix cp command
The "cp" command has not worked since
commit 0628ab8ec59834f98ede267edd21ddb8ba0bb57b,
because of the following lines, which set the destination
and the source to the same address.
Stephen Warren [Thu, 23 May 2013 10:22:10 +0000 (10:22 +0000)]
ext4: assign get_fs()->dev_desc before using it
Commit 50ce4c0 "fs/ext4: Support device block sizes != 512 bytes"
modified ext4fs_set_blk_dev() to calculate total_sect based on
get_fs()->dev_desc->log2blksz rather than SECTOR_SIZE. However, this
value wasn't yet assigned. Move the assignment earlier so the code
doesn't crash or hang.
Cc: Egbert Eich <eich@suse.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
While other architectures have enabled these gcc / ld options for some
time on U-Boot itself, ARM has only been doing this on SPL. Enable this
on full U-Boot as well now.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@ti.com>
Andre Przywara [Tue, 9 Apr 2013 02:20:32 +0000 (02:20 +0000)]
ARM: vexpress: add support for Versatile Express Cortex-A15-TC2
This adds support for the Cortex-A15-TC2 core tile for the Versatile
Express board by ARM. This is mostly a copy of the A5 support file,
but will be extended later with A15 specific options.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Ryan Harkin [Tue, 9 Apr 2013 02:20:31 +0000 (02:20 +0000)]
ARM: vexpress: create A5 specific board config
This patch creates a new config for the A5 dual core tile that includes the
generic config for the Versatile Express platform.
The generic config has been modified to provide support for the Extended
Memory Map, as used on the A5 core tile. A5 does not support the legacy
memory map.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Masahiro Yamada [Fri, 17 May 2013 05:50:37 +0000 (14:50 +0900)]
cfi_flash: return NULL for invalid base address input
When base address given was out of valid flash address ranges,
flash_get_info() function returned the pointer to the last
element of flash_info[i] array.
This patch changes this function to return NULL pointer
in such a case, which is more correct behaviour.
The function flash_protect_default() calls flash_protect()
immediately after flash_get_info() invocation.
With this correction, flash_protect() function would be
able to return soon, for NULL flash_info.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Stefan Roese <sr@denx.de>
Andrew Gabbasov [Tue, 14 May 2013 17:27:52 +0000 (12:27 -0500)]
cfi_flash: Fix unaligned accesses to cfi_qry structure
Packed structure cfi_qry contains unaligned 16- and 32-bits members,
accessing which causes problems when cfi_flash driver is compiled with
-munaligned-access option: flash initialization hangs, probably
due to data error.
Since the structure is supposed to replicate the actual data layout
in CFI Flash chips, the alignment issue can't be fixed in the structure.
So, unaligned fields need using of explicit unaligned access macros.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Stefan Roese <sr@denx.de>
htbegin [Fri, 1 Mar 2013 23:00:34 +0000 (23:00 +0000)]
mtd: nand: use ssize_t instead of size_t to prevent infinite loop
When a all 0xFF buffer is passed to drop_ffs, the no-0xFF check loop
will loop forever.
After the fix, If ssize_t i = -1 and size_t l = i + 1, the value of l
will still be 0 as expected.
Signed-off-by: Tao Hou <hotforest@gmail.com> Cc: Ben Gardiner <bengardiner@nanometrics.ca> Cc: Scott Wood <scottwood@freescale.com>
Harvey Chapman [Tue, 26 Feb 2013 17:57:14 +0000 (17:57 +0000)]
nand: adjust erase/read/write partition/chip size for bad blocks
Adjust the sizes calculated for whole partition/chip operations by
removing the size of bad blocks so we don't try to erase/read/write
past a partition/chip boundary.
Scott Wood [Tue, 26 Feb 2013 13:00:50 +0000 (13:00 +0000)]
nand/fsl_elbc: detect page size at runtime
This avoids needing a separate U-Boot config when some revisions
of a board have small-page NAND and other revisions have large-page
NAND (except for NAND SPL targets).
CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and
it gets in the way of this change.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Bo Shen [Sun, 12 May 2013 23:28:38 +0000 (23:28 +0000)]
ARM: at91: fix and update README.at91 document
This patch implement following things
- The link no longer accessable
- Remove the error configuration command
- Update soldered data flash memory map
- Update at91sam9m10g45ek memory size to 128MiB
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Sun, 12 May 2013 22:40:54 +0000 (22:40 +0000)]
ARM: atmel: add sama5d3xek support
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
projects / u-boot.git / log
![11 years agopowerpc/t4qds: Add SW7[4] in the DIP switch display](/img/sics.gif?p=u-boot.git;a=commit;h=e1379b0730fcef15e6e77305a56f35912697409c){kind=link}
