Simon Glass [Sat, 7 Jan 2023 21:07:08 +0000 (14:07 -0700)]
binman: Allow writing section contents to a file
At present only the image (which is a section) has a filename. Move this
implementation to the entry_Section class so that any section can have a
filename. With this, the section data is written to a file.
This allows parts of an image to be written, along with the entire image.
Make a note that this can be used to include the contents of a section in
one image in another (later) image.
Simon Glass [Wed, 21 Dec 2022 14:27:39 +0000 (07:27 -0700)]
dm: pinctrl: Revert "pinctrl: probe pinctrl drivers during post-bind"
This breaks chromebook_coral and it is also not how things should work. If
a board needs to bind GPIOs as part of a pinctrl driver this can be done
during the bind step, if needed.
We cannot probe pinctrl devices when binding as a rule, since it cannot be
supported on some platforms.
The bind and probe steps are separate in U-Boot and they should remain
separate.
Simon Glass [Sat, 7 Jan 2023 21:57:30 +0000 (14:57 -0700)]
rockchip: Enable bootstage on rockpro64
This board is useful for benchmarking overall U-Boot performance. Enable
the bootstage feature so we get a report.
Since this returns to the boot rom before finishing executing
board_init_r() in SPL, add a few bootstage calls so that we can collect
timing from TPL.
For the stash region, use a portion of SRAM, 64KB below the stack top.
This allows the TPL image to be up to nearly 120KB (it is typically about
64KB). SPL normally runs from SDRAM at 0, so can use the same stash
region.
Simon Glass [Wed, 21 Dec 2022 23:08:23 +0000 (16:08 -0700)]
mkimage: Add a few more messages for FIT failures
Add messages to make it clearer which part of the FIT creation is failing.
This can happen when an invalid 'algo' property is provided in the .its
file.
Simon Glass [Wed, 21 Dec 2022 23:08:21 +0000 (16:08 -0700)]
fdt: Check for overlapping data and FDT
If the FDT overlaps with the data region of the image, or with the stack,
it can become corrupted before relocation. Add a check for this, behind a
debug flag, as it can be very confusing and time-consuming to debug.
Tom Rini [Tue, 17 Jan 2023 13:55:40 +0000 (08:55 -0500)]
Merge branch '2022-01-16-bootstd-updates'
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
Tony Dinh [Fri, 30 Dec 2022 05:45:57 +0000 (21:45 -0800)]
arm: kirkwood: Convert to DM Serial for various Kirkwood boards
For Kirkwood boards, it is necessary to have early malloc in DRAM area
when Driver Model for Serial is enabled. Please see Michael's patch here:
https://lore.kernel.org/u-boot/20220817193809.1059688-20-michael@walle.cc/
This patch enables the early malloc in DRAM for all Kirkwood boards.
Note that this will work for boards that have either non-DM serial
and DM_SERIAL. Also, add the CONFIG_KIRKWOOD_COMMON option to enable
DM_SERIAL as a common option for boards that have been tested.
Stefan Roese [Mon, 16 Jan 2023 08:01:48 +0000 (09:01 +0100)]
timer: orion-timer: Fix problem in early_init_done()
It was noticed that Clearfog is currently broken with this newly
introduced early_init_done() function. Apparently the timer is enabled
here when U-Boot is run but not configured - at least not correctly.
Resulting in a hangup in the timer reading functions.
To fix this, also read the value of the reload register and check it's
value with the one written to by U-Boot. Only if this matches, the
init has already been done.
Fixes: 5387b093cb79 ("timer: orion-timer: Fix problem with early static variable") Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Pali Rohár <pali@kernel.org> Cc: Martin Rowe <martin.p.rowe@gmail.com> Cc: Tony Dinh <mibodhi@gmail.com> Cc: Pali Rohár <pali@kernel.org> Cc: Michael Walle <michael@walle.cc>
Tom Rini [Tue, 17 Jan 2023 01:58:37 +0000 (20:58 -0500)]
Merge tag 'u-boot-rockchip-20230117' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rv1126 soc and rv1126 neu2 io board;
- Add support for rk3399 pine64 pinephone pro board;
- dts sync from linux for rk3399 and px30;
- Add support for PX30 Ringneck SoM board;
Simon Glass [Fri, 6 Jan 2023 14:52:36 +0000 (08:52 -0600)]
expo: Add basic implementation
An expo is a way of presenting and collecting information from the
user. It consists of a collection of 'scenes' of which only one is
presented at a time. An expo is typically used to show a boot menu
and allow settings to be changed.
One created, the same expo can be automatically presented in graphical
form using a vidconsole, or in text form on a serial console.
Add an initial implementation of the expo itself. Supports for scenes
and objects is provided later.
Simon Glass [Fri, 6 Jan 2023 14:52:28 +0000 (08:52 -0600)]
image: Move common image code to image_board and command
We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Simon Glass [Fri, 6 Jan 2023 14:52:27 +0000 (08:52 -0600)]
image: Add a function to find a script in an image
Split this functionality out of the 'source' command so it can be used
from another place. For now leave it where it is, but a future patch will
move it out of cmd/
Simon Glass [Fri, 6 Jan 2023 14:52:20 +0000 (08:52 -0600)]
cli: Move readline character-processing to a state machine
The current cread_line() function is very long. It handles the escape
processing inline. The menu command does similar processing but at the
character level, so there is some duplication.
Split the character processing into a new function cli_ch_process() which
processes individual characters and returns the resulting input character,
taking account of escape sequences. It requires the caller to set up and
maintain its state.
Update cread_line() to use this new function.
The only intended functional change is that an invalid escape sequence
does not add invalid/control characters into the input buffer, but instead
discards these.
Simon Glass [Fri, 6 Jan 2023 14:52:19 +0000 (08:52 -0600)]
sandbox: Enable mmc command and legacy images
The mmc command is useful for testing mmc disk images in sandbox, so
enable it. We also need to enable legacy images so that we can run tests
which use them.
Disable it for a few avb tests since MMC is not implemented there yet.
Quentin Schulz [Mon, 9 Jan 2023 10:36:43 +0000 (11:36 +0100)]
rockchip: px30: insert u-boot, spl-boot-device into U-Boot device tree
It is possible to boot U-Boot proper from a different storage medium
than the one used by the BOOTROM to load the SPL. This information is
stored in the u-boot,spl-boot-device Device Tree property and is
accessible from U-Boot proper so that it has knowledge at runtime where
it was loaded from.
Quentin Schulz [Mon, 9 Jan 2023 10:36:42 +0000 (11:36 +0100)]
rockchip: px30: list possible SPL boot devices
BOOTROM sets a bit in a CPU register so that the software can know from
where the first stage bootloader was booted. One use case for this is to
specify the default loading medium for U-Boot proper to match the one
used by the BOOTROM to load the SPL (same-as-spl in
u-boot,spl-boot-order).
Let's create the mapping between BOOTROM value and Device Tree node
names for MMC devices.
Quentin Schulz [Mon, 9 Jan 2023 10:36:40 +0000 (11:36 +0100)]
rockchip: px30: fix possibly unused grf and cru variables
The grf and cru are only used when no UART base is provided by the user
(defaults to UART2) or for UART1, UART3 and UART5 to be used for the
debug UART. Therefore, let's surround those variable definitions with
the proper checks.
This wasn't an issue before support for UART0 was added, because all
cases were using cru and grf. UART0 only uses pmucru so there's a need
to not define those variables anymore.
Fixes: d0af506625ff ("rockchip: px30: support debug uart on UART0") Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peter Robinson [Sat, 31 Dec 2022 09:24:00 +0000 (09:24 +0000)]
rockchip: Add initial support for the PINE64 Pinephone Pro
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 14 Dec 2022 17:51:05 +0000 (23:21 +0530)]
arm: rockchip: Add RV1126 arch core support
Rockchip RV1126 is a high-performance vision processor SoC
for IPC/CVR, especially for AI related application.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai> Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I22fde40ec375e3c6aba39808abf252edc45d4b04
Jagan Teki [Wed, 14 Dec 2022 17:51:04 +0000 (23:21 +0530)]
ARM: dts: rockchip: Add Rockchip RV1126 SoC
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
John Keeping [Fri, 18 Nov 2022 16:13:18 +0000 (16:13 +0000)]
rockchip: mkimage: make RC4 key const
This is read-only data, so mark it as such.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
John Keeping [Fri, 18 Nov 2022 16:13:17 +0000 (16:13 +0000)]
rc4: mark key as const
Key data is never written so the parameter can be const, which allows
putting fixed keys in .rodata.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Tue, 15 Nov 2022 14:46:23 +0000 (15:46 +0100)]
rockchip: puma-rk3399: sync DTS with Linux kernel next-20221114
This synchronizes the Device Trees related to Puma RK3399 SoM with Linux
kernel next-20221114 to include two important changes pertaining to
eMMC and SD card instability.
Quentin Schulz [Fri, 11 Nov 2022 11:25:48 +0000 (12:25 +0100)]
rockchip: px30: make watchdog and tsadc trigger a first global reset
By default, the PX30 is configured for watchdog and tsadc to trigger a
second global reset which is a more permissive reset than first global
reset.
From TRM part 1 "2.3 System Reset Solution":
glb_srstn_1 will reset the all logic, and
glb_srstn_2 will reset the all logic except GRF, SGRF and all GPIOs.
This enforces that the watchdog and tsadc trigger glb_srstn_1 as
similarly done for RK3399 in U-Boot (in SDRAM driver for some reason?),
TF-A and Coreboot.
Pullup is used by the usb framework in order to do software-controlled
usb_gadget_connect() and usb_gadget_disconnect().
Implement pullup() for dwc2 using the SOFT_DISCONNECT bit in the dctl
register:
* when pullup is on, clear SOFT_DISCONNECT
* when pullup is off, set SOFT_DISCONNECT
This is especially useful when a gadget disconnection is initiated but
no board_usb_cleanup() is called.
Add a new CONFIG_USB_HUB_DEBOUNCE_TIMEOUT to increase the
HUB_DEBOUNCE_TIMEOUT value, for example to 2s because some usb device
needs around 1.5s or more to make the hub port status to be
connected steadily after being powered off and powered on.
This 2s value is aligned with Linux driver and avoids to configure
"usb_pgood_delay" as a workaround for connection timeout on
some USB device; normally the env variable "usb_pgood_delay" is used
to delay the first query after power ON and thus the device answer,
but this variable not used to increase the connection timeout delay.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Hai Pham [Thu, 22 Dec 2022 21:18:01 +0000 (22:18 +0100)]
ARM: renesas: condor: switch eMMC bus to 1V8
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Marek Vasut [Thu, 22 Dec 2022 21:17:20 +0000 (22:17 +0100)]
ARM: dts: renesas: condor: Enable SPI NOR fast-read
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Thu, 22 Dec 2022 21:06:46 +0000 (22:06 +0100)]
ARM: renesas: ulcb: Set CONFIG_TEXT_BASE=0x0 on R-Car Gen3 ULCB
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since 534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Thu, 22 Dec 2022 21:07:08 +0000 (22:07 +0100)]
ARM: renesas: condor: Set CONFIG_TEXT_BASE=0x0 on R-Car Gen3 Condor
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since 534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
projects / u-boot.git / log
