Tim Harvey [Fri, 8 Aug 2014 05:35:42 +0000 (22:35 -0700)]
imx: ventana: added cputype env var
There are many similarities between the IMX6QUAD/IMX6DUAL and there are
many similarities between the IMX6SOLO/IMX6DUALITE. Add a 'soctype' env
variable that tells you which type you have.
Tim Harvey [Thu, 21 Aug 2014 06:35:14 +0000 (23:35 -0700)]
imx: ventana: add GW5520 support
The GW5520 has an IMX6Q SoC with 512MB of DDR3, 256MB of NAND flash as well as:
* 2x MiniPCIe sockets
* 2x USB host sockets
* 2x i210 GigE
* HDMI out
* digital I/O expansion
Tim Harvey [Thu, 21 Aug 2014 06:31:11 +0000 (23:31 -0700)]
imx: ventana: base SPL MMDC calibration on width and size not board
The IMX6 MMDC calibration registers depend on propagation delay and capacitive
loading between the SoC's MMDC and the DDR3 chips. On the Ventana boards the
board layout varies little in trace-lengths such that propagation delays are
irrelevant thus we can simply things by using calibration values obtained
from various board layouts based on a common SoC and DDR chip configuration.
This eliminates board-model from being needed allowing more flexibility. These
values were tested on a large sample size of Gateworks Ventana boards ranging
in layout, and memory configuration over the entire temperature range supported.
Fabio Estevam [Mon, 25 Aug 2014 16:34:17 +0000 (13:34 -0300)]
net: fec_mxc: Poll FEC_TBD_READY after polling TDAR
When testing the FEC driver on a mx6solox we noticed that the TDAR bit gets
always cleared prior then the READY bit is cleared in the last BD, which causes
FEC packets reception to always fail.
As explained by Ye Li:
"The TDAR bit is cleared when the descriptors are all out from TX ring, but on
mx6solox we noticed that the READY bit is still not cleared right after TDAR.
These are two distinct signals, and in IC simulation, we found that TDAR always
gets cleared prior than the READY bit of last BD becomes cleared.
In mx6solox, we use a later version of FEC IP. It looks like that this
intrinsic behaviour of TDAR bit has changed in this newer FEC version."
Fix this by polling the READY bit of BD after the TDAR polling, which covers the
mx6solox case and does not harm the other SoCs.
No performance drop has been noticed with this patch applied when testing TFTP
transfers on several boards of different i.mx SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
video: exynos_fimd: Add framework to disable FIMD sysmmu
On Exynos5420 and newer versions, the FIMD sysmmus are in
"on state" by default.
We have to disable them in order to make FIMD DMA work.
This patch adds the required framework to exynos_fimd driver,
and disables FIMD sysmmu on Exynos5420.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arm: exynos: Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Patch is the result of:
sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h
sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig
Reported-by: Vagrant Cascadian <vagrant@debian.org> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com>
[ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove
redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
odroid: add board file for Odroid X2/U3 based on Samsung Exynos4412
This board file supports standard features of Odroid X2 and U3 boards:
- Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz,
- MAX77686 power regulator,
- USB PHY,
- enable XCL205 - power for board peripherials
- check board type: U3 or X2.
- enable Odroid U3 FAN cooler
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arm:reset: call the reset_misc() before the cpu reset
On an Odroid U3 board, the SOC is unable to reset the eMMC card
in the DWMMC mode by the cpu software reset. Manual reset of the card
by switching proper gpio pin - fixes this issue.
Such solution needs to add a call to pre reset function.
This is done by the reset_misc() function, which is called before reset_cpu().
The function reset_misc() is a weak function.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com>
Changes v4:
- arch/arm/reset: fix weak function attribute to proper style Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
samsung: misc: add function for setting $dfu_alt_info
This change introduces new common function:
- set_dfu_alt_info() - put dfu system and bootloader setting
into $dfu_alt_info.
functions declaration:
- char *get_dfu_alt_system(void)
- char *get_dfu_alt_boot(void)
- void set_dfu_alt_info(void)
and new config:
- CONFIG_SET_DFU_ALT_INFO
This function can be used for auto setting dfu configuration on boot.
Such feature is useful for multi board support by one u-boot binary.
Each board should define two functions:
- get_dfu_alt_system()
- get_dfu_alt_boot()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
board:samsung: check the boot device and init the right mmc driver.
It is possible to boot device using a micro SD or eMMC slots.
In this situation, boot device should be registered as a block
device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV
is usually set to "0" in the most config cases.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion
S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip
corrected' error messages. Possible cause was discussed in the
mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html
Quote (Author: Pekon Gupta <pekon@ti.com>): "The issue is mainly
due to a NAND protocol violation in the omap driver since the
Random Data Output command (05h-E0h) expects to see only the
column address that should be addressed within the already loaded
read page into the read buffer. Only 2 address cycles with ALE
active should be provided between the 05h and E0h commands. The
Page read command expects the full address footprint (2bytes for
column address + 3bytes for row address), but once the page is
loaded into the read buffer, Random Data Output should be used
with only 2bytes for column address."
This patch combines the solution proposed in the mailinglist and
the patch provided by the Spansion company (GPLv2 code, source:
http://www.spansion.com/Support/Software/u-boot-psp-04.04.00.01-NAND.zip)
Since the CS of a device connected to the GPMC was
stored in the global variable, it was not possible to
use multiple devices. In this patch the CS is stored per
device in its 'struct omap_nand_info'. This makes it
possible to use up to 'GPMC_MAX_CS' NAND Flash devices
connected to U-boot.
In case when 4K page keystone RBL layout is used the compilation
error is appeared. That's because the #ifdef has to be placed under
struct name. This patch correct it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Bo Shen [Wed, 27 Aug 2014 09:28:18 +0000 (17:28 +0800)]
USB: gadget: s3c: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Bo Shen [Wed, 27 Aug 2014 09:28:17 +0000 (17:28 +0800)]
USB: gadget: atmel: get rid of debug compile warning
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Stephen Warren [Mon, 25 Aug 2014 20:02:15 +0000 (14:02 -0600)]
usb: ci_udc: implement dfu_usb_get_reset
This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Lukasz Majewski [Mon, 25 Aug 2014 09:07:29 +0000 (11:07 +0200)]
udc: dfu: s3c_udc: Provide function to check if USB reset was asserted
New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.
Without this function the previous DFU behavior is preserved.
Lukasz Majewski [Mon, 25 Aug 2014 09:07:28 +0000 (11:07 +0200)]
dfu: Provide means to find difference between dfu-util -e and -R
This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.
By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.
Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.
It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.
Simon Glass [Mon, 11 Aug 2014 15:23:53 +0000 (09:23 -0600)]
dm: gpio: Allow gpio command to adjust GPIOs that are busy
The gpio command mostly relies on gpio_request() and gpio_free() being
nops, in that you can request a GPIO twice. With driver model this is
now implemented correctly, so it fails.
Change the command to deal with a failure to claim the GPIO.
Simon Glass [Mon, 11 Aug 2014 15:23:52 +0000 (09:23 -0600)]
dm: gpio: Enhance gpio command to show only active GPIOs
The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.
In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.
Masahiro Yamada [Sun, 31 Aug 2014 15:47:55 +0000 (00:47 +0900)]
mx6: tqma6: get board support back to Kconfig build system
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
arm: Add missing .vectors section to linker scripts
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Holger Brunck [Fri, 15 Aug 2014 08:51:48 +0000 (10:51 +0200)]
arm/km: disable subpage write for km_kirkwood_pci and kmsuv31 target
Newer FLASH types used on these boards don't allow writing of subpages.
So disable subpage write in the NAND driver. Additionally we need to
tell the UBI layer in the kernel that he also should only write 2048
bytes. This is done with an additional command line parameter for the
kernel commandline.
Tom Rini [Thu, 14 Aug 2014 10:42:36 +0000 (06:42 -0400)]
cmd_bootm.c: Add 'booti' for ARM64 Linux kernel Images
The default format for arm64 Linux kernels is the "Image" format,
described in Documentation/arm64/booting.txt. This, along with an
optional gzip compression on top is all that is generated by default.
The Image format has a magic number within the header for verification,
a text_offset where the Image must be run from, an image_size that
includes the BSS and reserved fields.
This does not support automatic detection of a gzip compressed image.
Marek Vasut [Sun, 3 Aug 2014 23:45:46 +0000 (01:45 +0200)]
ARM: Fix overflow in MMU setup
The patch fixes a corner case where adding size to DRAM start resulted
in a value (1 << 32), which in turn overflew the u32 computation, which
resulted in 0 and it therefore prevented correct setup of the MMU tables.
The addition of DRAM bank start and it's size can end up right at the end
of the address space in the special case of a machine with enough memory.
To prevent this overflow, shift the start and size separately and add them
only after they were shifted.
Hopefully, we only have systems in tree which have DRAM size aligned to
1MiB boundary. If not, this patch would break such systems. On the other
hand, such system would be broken by design anyway.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Jiandong Zheng [Sat, 2 Aug 2014 03:37:16 +0000 (20:37 -0700)]
arm: bcm281xx: net: Add Ethernet Driver
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com>
Andre Przywara [Fri, 1 Aug 2014 11:35:44 +0000 (13:35 +0200)]
ARM: enable ARMv7 virt support for the Arndale board
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pavel Machek [Mon, 14 Jul 2014 12:14:17 +0000 (14:14 +0200)]
socfpga: initialize designware ethernet
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Thomas Chou [Sat, 30 Aug 2014 09:45:23 +0000 (17:45 +0800)]
nios2: rebase nios2-generic board to 3c120 reference design
Though nios2-generic board meant to be a template, it is helpful
to be able to test on a real hardware. As the nios2 linux is
developed and tested on a 3c120 FPGA based Golden Hardware Reference
Design, it makes sense to rebase nios2-generic on this FPGA design.
Thomas Chou [Mon, 25 Aug 2014 09:43:12 +0000 (17:43 +0800)]
serial: move nios2-yanu.h into opencores_yanu driver
The nios2-yanu.h contains hardware registers and bits of
opencores yanu. As there is no other user of this header
, it should be moved into the driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> CC: Renato Andreola <renato.andreola@imagos.it>
projects / u-boot.git / log
