Stephen Warren [Fri, 14 Feb 2014 03:44:07 +0000 (20:44 -0700)]
ARM: rpi_b: rework boot scripts, enable sysboot
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.
While at it, enable booting from extlinux.conf using the sysboot command.
The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Thu, 6 Feb 2014 03:49:22 +0000 (20:49 -0700)]
ARM: rpi_b: load /uEnv.txt from MMC at startup
The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Thu, 6 Feb 2014 03:49:21 +0000 (20:49 -0700)]
ARM: rpi_b: convert to use distro defaults
Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Thu, 6 Feb 2014 03:49:20 +0000 (20:49 -0700)]
pxe: allow compilation when !defined(CONFIG_CMD_NET)
pxe.c provides both the "pxe" command which relies on a network, and the
"sysboot" command which doesn't. Fix the file to compile when network
support isn't enabled. This is useful e.g. on the Raspberry Pi which has
no network support yet, but will soon support the sysboot command.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Albert ARIBAUD [Thu, 20 Feb 2014 12:16:05 +0000 (13:16 +0100)]
Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Masahiro Yamada [Thu, 13 Feb 2014 09:30:26 +0000 (18:30 +0900)]
Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Masahiro Yamada [Wed, 5 Feb 2014 02:28:26 +0000 (11:28 +0900)]
dts: move device tree sources to arch/$(ARCH)/dts/
Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.
I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.
For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.
This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.
Masahiro Yamada [Wed, 5 Feb 2014 01:52:52 +0000 (10:52 +0900)]
kernel-doc: fix some errors
- Delete fs.xml from DOCBOOKS to fix an error.
Commit e3ff797c added fs.xml to DOCBOOKS
but missed to add doc/DocBook/fs.tmpl.
- Fix the location of include guard in include/linker_lists.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Abraham Varricatt <abraham.varricatt@vvdntech.com> Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 4 Feb 2014 08:24:44 +0000 (17:24 +0900)]
kbuild: Do not generate .*.su files at the top directory
Without this workaround, you will see a lot of ".*.su" files
at the top directory after building with a compiler
which supports "-fstack-usage" option.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:43 +0000 (17:24 +0900)]
board: sandburst: delete FORCEBUILD
We had switched to Kbuild, so we do not need to
delete sandburst board files at every build.
U-Boot conventional build system did not check the
update of command line option, -DBUILDUSER.
Kbuild can handle it nicely and re-builds object files
when command line options are changed.
(The file ".*.cmd" stores the information how the file
was generated at the previous build.)
Masahiro Yamada [Tue, 4 Feb 2014 08:24:41 +0000 (17:24 +0900)]
kbuild: support simultaneous board configuration and "make all"
This commit fixes two problems:
[1] We could not do board configuration and "make all"
in one command line.
For example, the following did not work as we expect:
$ make sandbox_config all
Configuring for sandbox board...
make: Nothing to be done for `all'.
[2] mixed-target build did not work with -j option
For example, the following did not work:
$ make -j8 sandbox_config u-boot
Makefile:481: *** "System not configured - see README". Stop.
make: *** [u-boot] Error 2
make: *** Waiting for unfinished jobs....
Configuring for sandbox board...
Going forward, we can do
$ make -j8 sandbox_config all
This is the same as
$ make sandbox_config
$ make -j8
Masahiro Yamada [Tue, 4 Feb 2014 08:24:38 +0000 (17:24 +0900)]
Makefile: Do not pass MTD_VERSION from the top Makefile
$(MTD_VERSION) is used in tools/env/Makefile
If you specify a variable at a command line like:
$ make MTD_VERSION=old env
or specify it thru an envrionment variable like:
$ export MTD_VERSION=old
$ make env
it is inherited to the sub-make too.
We do not need to pass it from the top Makefile explicitely.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:37 +0000 (17:24 +0900)]
kbuild: refactor Makefile and spl/Makefile more
This commit refactors rules of directory descending
and defines u-boot-dirs and u-boot-all-dirs.
(We will need u-boot-all-dirs when using
scripts/Makefile.clean)
Masahiro Yamada [Tue, 4 Feb 2014 08:24:33 +0000 (17:24 +0900)]
kbuild: generate {spl, tpl}-autoconf.mk only when it is necessary
Before this commit, {spl,tpl}-autoconf.mk was always generated
at the top Makefile even if SPL(TPL) build was not selected.
This commit moves the build rule of {spl,tpl}-autoconf.mk
from the top Makefile to spl/Makefile.
It prevents unnecessary {spl,tpl}-autoconf.mk from being
generated.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:32 +0000 (17:24 +0900)]
kbuild: move include directives of board configuration files
This commit changes the location of include directives
of board configuration files.
The purpose of this change is:
- Slim down $(TOPDIR)/config.mk
- Prevent $(TOPDIR)/Makefile from including the same
configuration file twice
- Do not include include/config.mk multiple times
because ARCH, CPU, BOARD, VENDOR, SOC are exported
Before this commit:
- include/autoconf.mk was included from $(TOPDIR)/Makefile
and $(TOPDIR)/config.mk
(This means $(TOPDIR)/Makefile included include/autoconf.mk twice)
- include/{spl,tpl}-autoconf.mk was included from $(TOPDIR)/config.mk
- include/config.mk was included from $(TOPDIR)/Makefile
and $(TOPDIR)/config.mk
(This means $(TOPDIR)/Makefile included include/config.mk twice)
After this commit:
- include/autoconf.mk is included from $(TOPDIR)/Makefile
and $(TOPDIR)/scripts/Makefile.build
- include/{spl,tpl}-autoconf.mk is included from $(TOPDIR)/spl/Makefile
and $(TOPDIR)/scripts/Makefile.build
- include/config.mk is included from $(TOPDIR)/config.mk and
$(TOPDIR)/spl/Makefile
Masahiro Yamada [Tue, 4 Feb 2014 08:24:28 +0000 (17:24 +0900)]
kbuild: use Linux Kernel build scripts
Now we are ready to switch over to real Kbuild.
This commit disables temporary scripts:
scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
scripts/{Makefile.build,Makefile.host,Makefile.lib}.
This switch is triggered by the line in scripts/Kbuild.include
-build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
+build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj
We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.
Additionally, we need to fix compiler flags which are
locally added or removed.
In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Gerhard Sittig <gsi@denx.de>
Masahiro Yamada [Tue, 4 Feb 2014 08:24:26 +0000 (17:24 +0900)]
Makefile: rename scripts/Makefile.build to scripts/Makefile.build.tmp
Some build scripts including scripts/Makefile.build
will be imported from Linux Kernel in the next commit.
We need to adjust them for U-Boot in the following commits.
To make it easier for reviewers to track the modification,
this commit renames scripts/Makefile.build to
scripts/Makefile.build.tmp beforehand.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:24 +0000 (17:24 +0900)]
kbuild: change out-of-tree build
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Gerhard Sittig <gsi@denx.de>
Masahiro Yamada [Tue, 4 Feb 2014 08:24:19 +0000 (17:24 +0900)]
Makefile: move more flags to the top Makefile
Before this commit, most of compiler flags were defined in config.mk.
But it is redundant because config.mk is included from all recursive make.
This commit moves many complier flags to the top Makefile
and export them.
And we use new vaiarables to store them:
KBUILD_CPPFLAGS, KBUILD_CFLAGS, KBUILD_AFLAGS.
This will allow us to switch more smoothly to Kbuild.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:18 +0000 (17:24 +0900)]
kbuild: Use Kbuild.include
This commit adjusts some files to use Kbuild.include.
- Use cc-option defined in Kbuild.include
(Delete cc-option in config.mk)
- Use cc-version defined in
(Delete cc-version in config.mk)
- Move binutils-version and dtc-version to Kbuild.include
by analogy to cc-version
This commit also adds srctree (same as SRCTREE)
to use Kbuild scripts.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:15 +0000 (17:24 +0900)]
Makefile: move some variable definitions to the top Makefile
This commit moves some variable definitions from config.mk
to the top Makefile:
- HOSTCC, HOSTCFLAGS, HOSTLDFLAGS
- AS, LD, CC, CPP, etc.
- SHELL (renamed to CONFIG_SHELL)
I'd like to slim down config.mk file
because it is included from all recursive make.
It is redundant to re-define the variables
every time descending into sub directories.
We should rather define them at the top Makefile
and export them.
U-Boot makefiles has been used "SHELL" variable to store shell
chosen for the user, whereas Linux Kernel uses "CONFIG_SHELL".
We should never use "SHELL" variable because it is
a special variable for GNU Make.
Changing SHELL may cause unpredictable side effects
whose root cause is usually difficult to find.
We should use a generic variable name "CONFIG_SHELL".
We should not use the syntax as follows either:
rm -f $(obj)tools/env/{fw_printenv,fw_setenv}
This depends on "bash" although GNU Make generally
invokes "sh" to run the each rule.
Masahiro Yamada [Tue, 4 Feb 2014 08:24:14 +0000 (17:24 +0900)]
Makfile: move suffix rules to Makefile.build
This commit moves suffix rules from config.mk
to scripts/Makefile.build, which will allow us
to switch smoothly to real Kbuild.
Note1:
post/lib_powerpc/fpu/Makefile has
its own rule to compile C sources.
We need to tweak it to keep the same behavior.
Note2:
There are two file2 with the same name:
arch/arm/lib/crt0.S and eamples/api/crt0.S.
To keep the same build behavior,
examples/api/Makefile also has to be treaked.
Wolfgang Denk [Fri, 31 Jan 2014 08:28:25 +0000 (09:28 +0100)]
EXT4: Fix number base handling of "ext4write" command
Unlike other commands (for example, "fatwrite"), ext4write would
interpret the "sizebytes" as decimal number. This is not only
inconsistend and unexpected to most users, it also breaks usage
like this:
Stephen Warren [Mon, 3 Feb 2014 20:21:06 +0000 (13:21 -0700)]
cmd_test: implement -e test for file existence
This is much like a regular shell's -e operator, except that it takes
multiple arguments to specify the device type and device/partition ID
in addition to the usual filename:
if test -e mmc 0:1 /boot/boot.scr; then echo yes; else echo no; fi
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 20:21:03 +0000 (13:21 -0700)]
cmd_test: check for binary operators before unary
This better mirrors the behaviour of bash, for example:
$ if test -z = -z; then echo yes; else echo no; fi
yes
This is parsed as a string comparison of "-z" and "-z", since the check
for the binary "=" operator occurs first. Without this change, the
command would be parsed as a -z test of "-", followed by a syntax error;
a trailing -z without and operand.
This is a behavioural change, but I believe any commands affected were
previously invalid or bizarely formed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 20:21:02 +0000 (13:21 -0700)]
cmd_test: use table lookup for parsing
do_test() currently uses strcmp() twice to determine which operator is
present; once to determine how many arguments the operator needs, then
a second time to actually decode the operator and implement it.
Rewrite the code so that a table lookup is used to translate the operator
string to an integer, and use a more efficient switch statement to decode
and execute the operator.
This approach also acts as enablement for the following patches.
This patch should introduce no behavioural change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 20:21:01 +0000 (13:21 -0700)]
fs: don't pass NULL dev_desc to most filesystems
FAT and ext4 expect that the passed in block device descriptor not be
NULL. This causes problems on sandbox, where get_device_and_partition()
succeeds for the "host" device, yet passes back a NULL device descriptor.
Add special handling for this situation, so that the generic filesystem
commands operate as expected on sandbox.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 3 Feb 2014 20:21:00 +0000 (13:21 -0700)]
fs: implement infrastructure for an 'exists' function
This could be used in scripts such as:
if test -e mmc 0:1 /boot/boot.scr; then
load mmc 0:1 ${scriptaddr} /boot/boot.scr
source ${scriptaddr}
fi
rather than:
if load mmc 0:1 ${scriptaddr} /boot/boot.scr; then
source ${scriptaddr}
fi
This prevents errors being printed by attempts to load non-existent
files, which can be important when checking for a large set of files,
such as /boot/boot.scr.uimg, /boot/boot.scr, /boot/extlinux.conf,
/boot.scr.uimg, /boot.scr, /extlinux.conf.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Mon, 3 Feb 2014 20:20:59 +0000 (13:20 -0700)]
fs: fix generic save command implementation
Fix a few issues with the generic "save" shell command, and fs_write()
function.
1) fstypes[].write wasn't filled in for some file-systems, and isn't
checked when used, which could cause crashes/... if executing save
on e.g. fat/ext filesystems.
2) fs_write() requires the length argument to be non-zero, since it needs
to know exactly how many bytes to write. Adjust the comments and code
according to this.
3) fs_write() wasn't prototyped in <fs.h> like other generic functions;
other code should be able to call this directly rather than invoking
the "save" shell command.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Sat, 25 Jan 2014 03:46:37 +0000 (20:46 -0700)]
README: document CONFIG_CMD_FS_GENERIC
This enables generic filesystem commands such as load and ls, which
automatically work with multiple filesystem types, without having to
be told which is present, unlike e.g. ext2load, fatls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Soren Brinkmann [Thu, 21 Nov 2013 21:39:00 +0000 (13:39 -0800)]
net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 22 Nov 2013 14:29:38 +0000 (15:29 +0100)]
zynq: timer: Fix hangs if network activity attempted after about one hour
Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes
in the section 4.1.1 how this value calculation should be done.
This patch fixes the problem if network activity such as ping or
tftp is attempted after u-boot has been idle for an hour,
it hangs, and cannot control-C out of it.
Signed-off-by: Uday Hegde <udayh@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
projects / u-boot.git / log
