net: tsec: add option to set device max-speed via dts
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
During the mainlining of the board this was by mistake set to sector size.
Our user space env scripts are expecting envsize of 0x4000, and setting
this differently will break our cross-platform compatibility.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:17 +0000 (10:51 +0800)]
mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes: 52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Fri, 21 May 2021 07:15:06 +0000 (15:15 +0800)]
configs: ls2088aqds: fix synchronous exception
IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)
armv8: ls1012a: Pass PPFE firmware to Linux through FDT
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Michael Walle [Tue, 13 Apr 2021 15:54:17 +0000 (17:54 +0200)]
board: sl28: fix RGMII clock and voltage
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 14 Jun 2021 14:45:58 +0000 (16:45 +0200)]
arm: mvebu: turris_{omnia, mox}: ensure running bootcmd_rescue always works
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
run bootcmd_rescue
in U-Boot's console.
Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.
Fixes: ec3784d62646 ("arm: mvebu: turris_mox: add support for board rescue mode") Fixes: 176c3e7760a2 ("arm: mvebu: turris_omnia: support invoking rescue boot from console") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Michal Simek [Thu, 10 Jun 2021 12:33:55 +0000 (14:33 +0200)]
arm64: zynqmp: Disable EFI_CAPSULE_ON_DISK_EARLY
Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.
EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Writing correct value to ANALOG_BUS
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Behún [Mon, 7 Jun 2021 14:34:47 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: add support for board rescue mode
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
The fragmented files were not correctly read because of two issues:
- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.
- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.
I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com> Tested-by: Richard Genoud <richard.genoud@posteo.net> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
João Loureiro [Wed, 17 Mar 2021 15:52:21 +0000 (16:52 +0100)]
usb: dwc2: Avoid delay when initializing USB peripheral by dwc2
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Add the missing dependency for the command ums:
- CONFIG_BLK: call of blk_* functions in usb_mass_storage.c
- CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Marek Vasut [Mon, 26 Apr 2021 20:04:11 +0000 (22:04 +0200)]
pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.12
Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Patrick Delaunay [Fri, 21 May 2021 10:24:59 +0000 (12:24 +0200)]
net: luton: remove address translation after ofnode_read_resource
Removed call of ofnode_translate_address() after ofnode_read_resource
in luton_switch.c:luton_probe(); it is unnecessary since
the commit feb7ac457c20 ("dm: core: Add address translation in
fdt_get_resource").
Fixes: feb7ac457c20 ("dm: core: Add address translation in fdt_get_resource") Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reported-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pwm: cros_ec: Rename "priv_auto_alloc_size" to "priv_auto"
With commit 41575d8e4c33 ("dm: treewide: Rename auto_alloc_size members
to be shorter") "priv_auto_alloc_size" was renamed to "priv_auto". This
driver was sent to the mailing list before that change, merged after it,
and still has the old form. Apply the rename here as well.
Fixes: 1b9ee2882e6b ("pwm: Add a driver for Chrome OS EC PWM") Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
os_find_text_base() assumes that first line of /proc/self/maps holds
information about the text. Hence we must call the function before calling
os_malloc() which calls mmap(0x10000000,).
Failure to do so has led to incorrect values for pc_reloc when an
exception was reported
=> exception undefined
Illegal instruction
pc = 0x5628d82e9d3c, pc_reloc = 0x5628c82e9d3c
as well as incorrect output of the bdinfo command
=> bdinfo
relocaddr = 0x0000000007858000
reloc off = 0x0000000010000000
Fixes: b308d9fd18fa ("sandbox: Avoid using malloc() for system state") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 30 Apr 2021 13:16:58 +0000 (21:16 +0800)]
of: addr: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
'dma-ranges' frequently exists without parent nodes having 'dma-ranges'.
While this is an error for 'ranges', this is fine because DMA capable
devices always have a translatable DMA address. Also, with no
'dma-ranges' at all, the assumption is that DMA addresses are 1:1 with
no restrictions unless perhaps the device itself has implicit
restrictions.
This keeps in sync with Linux kernel commit:
81db12ee15cb: of/address: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Behún [Fri, 28 May 2021 08:00:49 +0000 (10:00 +0200)]
arm: mvebu: turris_omnia: support invoking rescue boot from console
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:40 +0000 (17:59 +0200)]
arm: a37xx: pci: Fix configuring PCIe resources
The `ranges` DT property of the PCIe node is currently ignored by
Aardvark driver - all entries are used as transparent PCIe MEM, despite
some of them being defined for IO in DT.
This is because the driver does not setup PCIe outbound windows and thus
a default configuration is used.
This can cause an external abort on CPU when a device driver tries to
access non-MEM space.
Setup the PCIe windows according to the `ranges` property for all
non-MEM resources (currently only IO) and also non-transparent MEM
resources.
Because Linux expects that bootloader does not setup Aardvark PCIe
windows, disable them before booting Linux.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:39 +0000 (17:59 +0200)]
arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB
For some configurations with more PCIe cards and PCIe bridges, 16 MiB of
PCIe MEM space may not be enough. Since TF-A already allocates a 128 MiB
CPU window for PCIe, and since IO port space is only 64 KiB in total,
use all the remaining space (64 + 32 + 16 + 8 + 4 + 2 + 1 = 127 MiB) for
PCIe MEM.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:38 +0000 (17:59 +0200)]
arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function
Current version of this function uses a lot of incorrect assumptions about
the `ranges` DT property:
* parent(#address-cells) == 2
* #size-cells == 2
* number of entries == 2
* address size of first entry == 0x1000000
* second child address entry == base + 0x1000000
Trying to increase PCIe MEM space to more than 16 MiB leads to an overlap
with PCIe IO space, and trying to define additional MEM space (as a third
entry in the `ranges` DT property) causes U-Boot to crash when booting the
kernel.
## Flattened Device Tree blob at 04f00000
Booting using the fdt blob at 0x4f00000
Loading Device Tree to 000000001fb01000, end 000000001fb08f12 ... OK
ERROR: board-specific fdt fixup failed: <unknown error>
- must RESET the board to recover.
Fix a3700_fdt_fix_pcie_regions() to properly parse and update all addresses
in the `ranges` property according to
https://elinux.org/Device_Tree_Usage#PCI_Address_Translation
Now it is possible to increase PCIe MEM space from 16 MiB to maximal value
of 127 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Fixes: cb2ddb291ee6 ("arm64: mvebu: a37xx: add device-tree fixer for PCIe regions") Reviewed-by: Stefan Roese <sr@denx.de>
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:35 +0000 (17:59 +0200)]
arm: a37xx: pci: Disable bus mastering when unloading driver
Disable Root Bridge I/O space, memory space and bus mastering in Aardvark's
remove method, which is called before booting Linux kernel.
This ensures that PCIe device which was initialized and used by U-Boot
cannot do new DMA transfers until Linux initializes PCI subsystem and loads
appropriate drivers for the device.
During initialization of PCI subsystem Linux in fact disables this bus
mastering on Root Bridge (and later enables it when driver is loaded and
configured), but there is a possibility of a small window after U-Boot
boots Linux when bus mastering is enabled, which is not correct.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 26 May 2021 15:59:34 +0000 (17:59 +0200)]
arm: a37xx: pci: Don't put link into LTSSM Recovery state during probe
During our debugging of the Aardvark driver in Linux we have discovered
that the PCIE_CORE_LINK_CTRL_STAT_REG register in fact controls standard
PCIe Link Control Register for PCIe Root Bridge. This led us to discover
that the name of the PCIE_CORE_LINK_TRAINING macro and the corresponding
comment by this macro's usage is misleading; this bit in fact controls
Retrain Link, which, according to PCIe base spec is defined as:
A write of 1b to this bit initiates Link retraining by directing the
Physical Layer LTSSM to the Recovery state. If the LTSSM is already in
Recovery or Configuration, re-entering Recovery is permitted but not
required.
Entering Recovery state is normally done from LTSSM L0, L0s and L1 states.
But since the pci-aardvark.c driver enables Link Training just a few lines
above, the controller is not in L0 ready state yet. So setting aardvark bit
PCIE_CORE_LINK_TRAINING does not actually enter Recovery state at this
place.
Moreover, trying to enter LTSSM Recovery state without other configuration
is causing issues for some cards (e.g. Atheros AR9xxx and QCA9xxx). Since
Recovery state is not entered, these issues are not triggered.
Remove code which tries to enter LTSSM Recovery state completely.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Sean Anderson [Thu, 27 May 2021 16:02:34 +0000 (12:02 -0400)]
fastboot: Fix overflow when calculating chunk size
If a chunk was larger than 4GiB, then chunk_data_sz would overflow and
blkcnt would not be calculated correctly. Upgrade it to a u64 and cast
its multiplicands as well. Also fix bytes_written while we're at it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Heiko Schocher <hs@denx.de>
This contains the fix to bring back the SD card as MMC0. In the long run
we are looking into a more robust solution, but for now we need to fix
this, as this breaks the user experience left, right, and centre.
Also add the one MAINTAINERS path addition from Samuel.
Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:11 +0000 (06:52 -0700)]
riscv: dts: add fu740 support
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <green.wan@sifive.com>
[greentime.hu: set fu740 speed to 1.2GHz] Signed-off-by: Greentime Hu <greentime.hu@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
Green Wan [Thu, 27 May 2021 13:52:10 +0000 (06:52 -0700)]
drivers: pci: add pcie support for fu740
Add pcie driver for SiFive fu740, the driver depends on
fu740 gpio, clk and reset driver to do init. Force running at Gen1
for better capatible enumeration.
Several devices are tested:
a) M.2 NVMe SSD
b) USB-to-PCI adapter
c) Ethernet adapter (E1000 compatible)
Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
These drivers are sunxi platform-specific, and so are of interest to the
sunxi maintainers.
In fact, as there is no PHY driver maintainer, drivers/phy/allwinner had
no maintainer at all.
Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Fri, 16 Apr 2021 10:52:27 +0000 (11:52 +0100)]
sunxi: Bring back SD card as MMC device 0
Commit 2243d19e5618 ("mmc: mmc-uclass: Use dev_seq() to read aliases
node's index") now actually enforces U-Boot's device enumeration policy,
where explicitly named devices come first, then any other non-named
devices follow, without filling gaps.
For quite a while we have had an "mmc1 = &mmc2;" alias in our
sunxi-u-boot.dtsi, which now leads to the problem that the SD card
(which was always mmc device 0) now gets to be number 2.
This breaks quite some boot scripts, including our own distro boot
commands, and some other features looking at $mmc_bootdev, also
fastboot.
Just add an explicit mmc0 alias in the very same file to fix this and
restore the old behaviour.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Samuel Holland <samuel@sholland.org> Tested-by: Simon Baatz <gmbnomis@gmail.com>
Masahisa Kojima [Wed, 26 May 2021 03:09:58 +0000 (12:09 +0900)]
efi_loader: add PE/COFF image measurement
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_loader: Work-around build issue due to missing hash_calculate()
The hash_calculate() symbol is provided by hash-checksum.c. It depends
on hash_progressive_lookup_algo(), provided when CONFIG_HASH=y.
The issue is that hash_calculate() is used by the efi_loader,
irregardless of CONFIG_FIT_SIGNATURE. As pointed out in
commit 87316da05f2f ("lib: introduce HASH_CALCULATE option"),
enabling hash_calculate() based on CONFIG_FIT_SIGNATURE is incorrect.
To resolve this, use CONFIG_HASH as the compile switch for
hash-checksum.c. This ensures that all dependencies are compiled, and
is the most natural Kconfig to use.
There is the issue of having to 'select HASH' in a couple of places
that already 'select SHA256'. This is a deeper problem with how hashes
are organized, and fixing it is beyonf the scope of this change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
When we think of Kconfig, we usually think of features that we like
to enable or not. Ideally, we wouldn't use Kconfig to fix a build
issue, although sometimes it might make sense. With Kconfig it's hard
to guarantee that the fix is universal. We can only say that it works
for the set of tested configurations. In the majority of cases, it's
preferable to let the linker figure things out for us.
The reverted commit attempted to fix a build issue by adding an
invisible Kconfig option. This is wrong in several ways:
It invents a new Kconfig variable when CONFIG_HASH already
exists for the same purpose.
Second, hash-checksum.c makes use of the hash_progressive_lookup_algo()
symbol, which is only provided with CONFIG_HASH, but this dependency
was not expressed in the reverted patch.
It feels like Kconfig is turning into a listing of all available
source files, and a buffet to 'select' which ones to compile. The
purpose of this revert is to enable the next change to make use of
CONFIG_HASH instead of adding to Kconfig.
Ilias Apalodimas [Wed, 26 May 2021 18:01:00 +0000 (21:01 +0300)]
efi_loader: Fix coverity warnings for efi tcg2 protocol
Coverity reported 3 warnings on the current code.
CID 331856, 331855, 331854 on the latest scan.
Fix the rest of the warnings by initializing the variables before
passing them to tpm2_get_pcr_info().
In order to avoid future warnings and errors initialize them to 0 within
the function as well, since the values are always OR'ed after querying the
hardware.
arm: dts: stm32mp157c-odyssey-som: enable the RNG1
Enable the true random number generator. It can be used, for example, to
generate partition UUIDs when partitioning with the gpt command. The
generator is already enabled in the device trees of several other
STM32MP1‐based boards, like DKx or DHCOM.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Mon, 3 May 2021 11:31:39 +0000 (13:31 +0200)]
ARM: stm32: Add additional ID register check for KSZ8851 presence
Currently the code sets eth1addr only if /ethernet1 alias exists in DT,
the node pointed to by the alias has "micrel,ks8851-mll" compatible
string, and the KSZ8851 CCR register read indicates programmed EEPROM
is not connected.
This is not sufficient to detect cases where the DT still contains the
KSZ8851 nodes, but the chip itself is not present. Extend the detection
to handle these cases.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
projects / u-boot.git / log
