From: Hannes Schmelzer Date: Fri, 6 Jul 2018 13:41:28 +0000 (+0200) Subject: board/BuR/brppt1: convert brppt1 boards to driver model X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=fbc7c7decf47b22717d3aad13358f4d7440e7055;p=u-boot.git board/BuR/brppt1: convert brppt1 boards to driver model - add a devicetree for each variant (mmc, spi, nand) - drop unneeded code from board and bur/common - drop unneeded stuff from config header files - minor adaptions to be compliant with driver model (requesting gpio,..) - harmonize the commandset over all brppt1 targets Signed-off-by: Hannes Schmelzer --- diff --git a/arch/arm/dts/am335x-brppt1-mmc.dts b/arch/arm/dts/am335x-brppt1-mmc.dts new file mode 100644 index 0000000000..9be34d9da0 --- /dev/null +++ b/arch/arm/dts/am335x-brppt1-mmc.dts @@ -0,0 +1,345 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 B&R Industrial Automation GmbH + * http://www.br-automation.com + * + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "BRPPT1 (MMC) Panel"; + compatible = "ti,am33xx"; + + fset: factory-settings { + bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + version = <0x0100>; + order-no = "6PPT30 (MMC)"; + hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + serial-no = "0"; + device-id = <0x0>; + parent-id = <0x0>; + hw-variant = <0x1>; + }; + + aliases { + ds1bkl0 = &pwmbacklight; + ds1bkl1 = &tps_bl; + ds1timing = &timing0; + ds1ctrl = &lcdc; + gpmc = &gpmc; + mmc = &mmc2; + fset = &fset; + }; + + chosen { + bootargs = "console=ttyO0,115200 earlyprintk"; + stdout-path = &uart0; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + panel { + status = "disabled"; + + compatible = "ti,tilcdc,panel"; + enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + + backlight = <&pwmbacklight>; + bkl-pwm = <&pwmbacklight>; + bkl-tps = <&tps_bl>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + native-mode = <&timing0>; + timing0: lcd { + clock-frequency = <32000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <2>; + hback-porch = <192>; + hsync-len = <1>; + vfront-porch = <20>; + vback-porch = <2>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + pupdelay = <10>; + pondelay = <10>; + }; + }; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pwm0: omap-pwm@timer5 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer5>; + #pwm-cells = <3>; + }; + + pwm1: omap-pwm@timer6 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer6>; + #pwm-cells = <3>; + }; + + beeper: pwm-beep { + compatible = "pwm-beeper"; + pwms = <&pwm0 0 0 0>; + }; + + pwmbacklight: pwm-bkl { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000 0>; + + default-brightness-level = <255>; + brightness-levels = <0 16 32 64 128 170 202 234 255>; + + power-supply = <&vmmcsd_fixed>; + enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart0 { /* console uart */ + u-boot,dm-spl; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&i2c0 { + u-boot,dm-spl; + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { /* PMIC controller */ + u-boot,dm-spl; + reg = <0x24>; + compatible = "ti,tps65217"; + + tps_bl: backlight { + compatible = "ti,tps65217-bl"; + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */ + default-brightness = <50>; + }; + }; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <100000>; +}; + +&edma { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "host"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&davinci_mdio { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <1>; + }; + + phy1: ethernet-phy@1 { + reg = <2>; + }; +}; + +&mac { + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + dual_emac_res_vlan = <1>; + phy-mode = "mii"; +}; + +&cpsw_emac1 { + phy-handle = <&phy1>; + dual_emac_res_vlan = <2>; + phy-mode = "mii"; +}; + +&mmc1 { + u-boot,dm-spl; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <0x4>; + ti,non-removable; + ti,needs-special-hs-handling; + ti,vcc-aux-disable-is-sleep; + status = "okay"; +}; + +&mmc2 { + u-boot,dm-spl; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <0x8>; + ti,non-removable; + ti,needs-special-hs-handling; + ti,vcc-aux-disable-is-sleep; + status = "okay"; +}; + +&lcdc { + status = "disabled"; +}; + +&elm { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; + +&gpio0 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio1 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio2 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio3 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&wdt2 { + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,zx-cutoff-ratio = <40>; + ti,min_deviation = <60>; + ti,max_deviation = <600>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + + bnr-buttons { + Home-Button {}; + }; + }; + + adc { + ti,adc-channels = <5 6 7>; + }; +}; + +&timer6 { /* used for cpsw end device */ + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&timer7 { /* used for cpsw end device */ + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&wdt2 { + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&epwmss0 { + status = "okay"; +}; + +&tscadc { + status = "okay"; +}; + +&dcan0 { + status = "okay"; +}; + +&dcan1 { + status = "okay"; +}; + +&sham { + status = "disabled"; +}; + +&aes { + status = "disabled"; +}; + +&rng { + status = "disabled"; +}; diff --git a/arch/arm/dts/am335x-brppt1-nand.dts b/arch/arm/dts/am335x-brppt1-nand.dts new file mode 100644 index 0000000000..11bd5c551c --- /dev/null +++ b/arch/arm/dts/am335x-brppt1-nand.dts @@ -0,0 +1,363 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 B&R Industrial Automation GmbH + * http://www.br-automation.com + * + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "BRPPT1 (NAND) Panel"; + compatible = "ti,am33xx"; + + fset: factory-settings { + bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + version = <0x0100>; + order-no = "6PPT30 (NAND)"; + hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + serial-no = "0"; + device-id = <0x0>; + parent-id = <0x0>; + hw-variant = <0x1>; + }; + + aliases { + ds1bkl0 = &pwmbacklight; + ds1bkl1 = &tps_bl; + ds1timing = &timing0; + ds1ctrl = &lcdc; + gpmc = &gpmc; + mmc = &mmc2; + fset = &fset; + }; + + chosen { + bootargs = "console=ttyO0,115200 earlyprintk"; + stdout-path = &uart0; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + panel { + status = "disabled"; + + compatible = "ti,tilcdc,panel"; + enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + + backlight = <&pwmbacklight>; + bkl-pwm = <&pwmbacklight>; + bkl-tps = <&tps_bl>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + native-mode = <&timing0>; + timing0: lcd { + clock-frequency = <32000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <2>; + hback-porch = <192>; + hsync-len = <1>; + vfront-porch = <20>; + vback-porch = <2>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + pupdelay = <10>; + pondelay = <10>; + }; + }; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pwm0: omap-pwm@timer5 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer5>; + #pwm-cells = <3>; + }; + + pwm1: omap-pwm@timer6 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer6>; + #pwm-cells = <3>; + }; + + beeper: pwm-beep { + compatible = "pwm-beeper"; + pwms = <&pwm0 0 0 0>; + }; + + pwmbacklight: pwm-bkl { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000 0>; + + default-brightness-level = <255>; + brightness-levels = <0 16 32 64 128 170 202 234 255>; + + power-supply = <&vmmcsd_fixed>; + enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart0 { /* console uart */ + u-boot,dm-spl; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&i2c0 { + u-boot,dm-spl; + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { /* PMIC controller */ + u-boot,dm-spl; + reg = <0x24>; + compatible = "ti,tps65217"; + + tps_bl: backlight { + compatible = "ti,tps65217-bl"; + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */ + default-brightness = <50>; + }; + }; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <100000>; +}; + +&edma { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "host"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&davinci_mdio { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <1>; + }; + + phy1: ethernet-phy@1 { + reg = <2>; + }; +}; + +&mac { + dual_emac; + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + dual_emac_res_vlan = <1>; + phy-mode = "mii"; +}; + +&cpsw_emac1 { + phy-handle = <&phy1>; + dual_emac_res_vlan = <2>; + phy-mode = "mii"; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <0x4>; + ti,non-removable; + ti,needs-special-hs-handling; + ti,vcc-aux-disable-is-sleep; + status = "disabled"; +}; + +&lcdc { + status = "disabled"; +}; + +&elm { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; + +&gpio0 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio1 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio2 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio3 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&wdt2 { + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,zx-cutoff-ratio = <40>; + ti,min_deviation = <60>; + ti,max_deviation = <600>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + + bnr-buttons { + Home-Button {}; + }; + }; + + adc { + ti,adc-channels = <5 6 7>; + }; +}; + +&gpmc { + u-boot,dm-spl; + status = "okay"; + pinctrl-names = "default"; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + interrupt-parent = <&gpmc>; + rb-gpios = <&gpmc 1 GPIO_ACTIVE_HIGH>; /* gpmc_wait1 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,wait-pin = <1>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.MLO"; + reg = <0x00000000 0x000020000>; + }; + partition@1 { + label = "NAND.cfgscr"; + reg = <0x00020000 0x00020000>; + }; + partition@2 { + label = "NAND.dtb"; + reg = <0x00040000 0x00020000>; + }; + partition@3 { + label = "NAND.u-boot-env"; + reg = <0x00060000 0x00020000>; + }; + partition@4 { + label = "NAND.u-boot"; + reg = <0x00080000 0x00080000>; + }; + partition@5 { + label = "NAND.kernel"; + reg = <0x00100000 0x00400000>; + }; + partition@6 { + label = "NAND.rootfs"; + reg = <0x00500000 0x08000000>; + }; + partition@7 { + label = "NAND.user"; + reg = <0x08500000 0x17b00000>; + }; + }; +}; diff --git a/arch/arm/dts/am335x-brppt1-spi.dts b/arch/arm/dts/am335x-brppt1-spi.dts new file mode 100644 index 0000000000..522ed50902 --- /dev/null +++ b/arch/arm/dts/am335x-brppt1-spi.dts @@ -0,0 +1,366 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 B&R Industrial Automation GmbH + * http://www.br-automation.com + * + */ +/dts-v1/; + +#include "am33xx.dtsi" + +/ { + model = "BRPPT1 (MMC) Panel"; + compatible = "ti,am33xx"; + + fset: factory-settings { + bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + version = <0x0100>; + order-no = "6PPT30 (SPI)"; + hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; + serial-no = "0"; + device-id = <0x0>; + parent-id = <0x0>; + hw-variant = <0x1>; + }; + + aliases { + ds1bkl0 = &pwmbacklight; + ds1bkl1 = &tps_bl; + ds1timing = &timing0; + ds1ctrl = &lcdc; + gpmc = &gpmc; + mmc = &mmc2; + spi0 = &spi0; + fset = &fset; + }; + + chosen { + bootargs = "console=ttyO0,115200 earlyprintk"; + stdout-path = &uart0; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + panel { + status = "disabled"; + + compatible = "ti,tilcdc,panel"; + enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + + backlight = <&pwmbacklight>; + bkl-pwm = <&pwmbacklight>; + bkl-tps = <&tps_bl>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + + display-timings { + native-mode = <&timing0>; + timing0: lcd { + clock-frequency = <32000000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <2>; + hback-porch = <192>; + hsync-len = <1>; + vfront-porch = <20>; + vback-porch = <2>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + pupdelay = <10>; + pondelay = <10>; + }; + }; + }; + + vmmcsd_fixed: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pwm0: omap-pwm@timer5 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer5>; + #pwm-cells = <3>; + }; + + pwm1: omap-pwm@timer6 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer6>; + #pwm-cells = <3>; + }; + + beeper: pwm-beep { + compatible = "pwm-beeper"; + pwms = <&pwm0 0 0 0>; + }; + + pwmbacklight: pwm-bkl { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000 0>; + + default-brightness-level = <255>; + brightness-levels = <0 16 32 64 128 170 202 234 255>; + + power-supply = <&vmmcsd_fixed>; + enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart0 { /* console uart */ + u-boot,dm-spl; + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&i2c0 { + u-boot,dm-spl; + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { /* PMIC controller */ + u-boot,dm-spl; + reg = <0x24>; + compatible = "ti,tps65217"; + + tps_bl: backlight { + compatible = "ti,tps65217-bl"; + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */ + default-brightness = <50>; + }; + }; +}; + +&i2c2 { + status = "okay"; + clock-frequency = <100000>; +}; + +&spi0 { + u-boot,dm-spl; + status = "okay"; + + cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>, + <&gpio0 6 GPIO_ACTIVE_HIGH>, + <0>, + <0>; + + spi-max-frequency = <24000000>; + + spi_flash: spiflash@0 { + u-boot,dm-spl; + u-boot,dm-pre-reloc; + compatible = "spidev", "spi-flash"; + spi-max-frequency = <24000000>; + reg = <0>; + }; +}; + +&edma { + status = "okay"; +}; + +&cppi41dma { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "host"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&davinci_mdio { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <1>; + }; + + phy1: ethernet-phy@1 { + reg = <2>; + }; +}; + +&mac { + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + dual_emac_res_vlan = <1>; + phy-mode = "mii"; +}; + +&cpsw_emac1 { + phy-handle = <&phy1>; + dual_emac_res_vlan = <2>; + phy-mode = "mii"; +}; + +&mmc1 { + u-boot,dm-spl; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <0x4>; + ti,non-removable; + ti,needs-special-hs-handling; + ti,vcc-aux-disable-is-sleep; + status = "okay"; +}; + +&mmc2 { + u-boot,dm-spl; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <0x8>; + ti,non-removable; + ti,needs-special-hs-handling; + ti,vcc-aux-disable-is-sleep; + status = "okay"; +}; + +&lcdc { + status = "disabled"; +}; + +&elm { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&aes { + status = "okay"; +}; + +&gpio0 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio1 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio2 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&gpio3 { + u-boot,dm-spl; + ti,no-reset-on-init; +}; + +&wdt2 { + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&tscadc { + status = "okay"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,zx-cutoff-ratio = <40>; + ti,min_deviation = <60>; + ti,max_deviation = <600>; + ti,coordinate-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + + bnr-buttons { + Home-Button {}; + }; + }; + + adc { + ti,adc-channels = <5 6 7>; + }; +}; + +&timer6 { /* used for cpsw end device */ + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&timer7 { /* used for cpsw end device */ + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&wdt2 { + status = "okay"; + ti,no-reset-on-init; + ti,no-idle-on-init; +}; + +&epwmss0 { + status = "okay"; +}; + +&tscadc { + status = "okay"; +}; + +&dcan0 { + status = "okay"; +}; + +&dcan1 { + status = "okay"; +}; + +&sham { + status = "disabled"; +}; + +&aes { + status = "disabled"; +}; + +&rng { + status = "disabled"; +}; diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c index 87b76a660c..d2e7c72242 100644 --- a/board/BuR/brppt1/board.c +++ b/board/BuR/brppt1/board.c @@ -77,6 +77,8 @@ static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1}; void am33xx_spl_board_init(void) { + int rc; + struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER; /*struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;*/ struct cm_dpll *const cmdpll = (struct cm_dpll *)CM_DPLL; @@ -108,8 +110,21 @@ void am33xx_spl_board_init(void) i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); pmicsetup(0); - gpio_direction_output(64+29, 1); /* switch NAND_RnB to GPMC_WAIT1 */ - gpio_direction_output(64+28, 1); /* switch MII2_CRS to GPMC_WAIT0 */ + /* peripheral reset */ + rc = gpio_request(64 + 29, "GPMC_WAIT1"); + if (rc != 0) + printf("cannot request GPMC_WAIT1 GPIO!\n"); + rc = gpio_direction_output(64 + 29, 1); + if (rc != 0) + printf("cannot set GPMC_WAIT1 GPIO!\n"); + + rc = gpio_request(64 + 28, "GPMC_WAIT0"); + if (rc != 0) + printf("cannot request GPMC_WAIT0 GPIO!\n"); + rc = gpio_direction_output(64 + 28, 1); + if (rc != 0) + printf("cannot set GPMC_WAIT0 GPIO!\n"); + } const struct dpll_params *get_dpll_ddr_params(void) @@ -151,10 +166,13 @@ int board_late_init(void) { unsigned char bmode = 0; ulong bootcount = 0; + int rc; bootcount = bootcount_load() & 0xF; - if (gpio_get_value(REPSWITCH) == 0 || bootcount == 12) + rc = gpio_request(REPSWITCH, "REPSWITCH"); + + if (rc != 0 || gpio_get_value(REPSWITCH) == 0 || bootcount == 12) bmode = 12; else if (bootcount > 0) bmode = 0; diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c index 01e30783e2..f3eae5cbc1 100644 --- a/board/BuR/common/common.c +++ b/board/BuR/common/common.c @@ -22,15 +22,11 @@ #include #include #include -#include -#include #include #include #include "bur_common.h" #include "../../../drivers/video/am335x-fb.h" -static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; - DECLARE_GLOBAL_DATA_PTR; /* --------------------------------------------------------------------------*/ @@ -270,6 +266,9 @@ int ft_board_setup(void *blob, bd_t *bd) } #ifdef CONFIG_SPL_BUILD + +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + void pmicsetup(u32 mpupll) { int mpu_vdd; @@ -354,100 +353,6 @@ void set_mux_conf_regs(void) #endif /* CONFIG_SPL_BUILD */ -#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \ - (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD)) -static void cpsw_control(int enabled) -{ - /* VTP can be added here */ - return; -} - -/* describing port offsets of TI's CPSW block */ -static struct cpsw_slave_data cpsw_slaves[] = { - { - .slave_reg_ofs = 0x208, - .sliver_reg_ofs = 0xd80, - .phy_addr = 1, - }, - { - .slave_reg_ofs = 0x308, - .sliver_reg_ofs = 0xdc0, - .phy_addr = 2, - }, -}; - -static struct cpsw_platform_data cpsw_data = { - .mdio_base = CPSW_MDIO_BASE, - .cpsw_base = CPSW_BASE, - .mdio_div = 0xff, - .channels = 8, - .cpdma_reg_ofs = 0x800, - .slaves = 1, - .slave_data = cpsw_slaves, - .ale_reg_ofs = 0xd00, - .ale_entries = 1024, - .host_port_reg_ofs = 0x108, - .hw_stats_reg_ofs = 0x900, - .bd_ram_ofs = 0x2000, - .mac_control = (1 << 5), - .control = cpsw_control, - .host_port_num = 0, - .version = CPSW_CTRL_VERSION_2, -}; -#endif /* CONFIG_DRIVER_TI_CPSW, ... */ - -#if defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD) -int board_eth_init(bd_t *bis) -{ - int rv = 0; - char mac_addr[6]; - const char *mac = 0; - uint32_t mac_hi, mac_lo; - /* try reading mac address from efuse */ - mac_lo = readl(&cdev->macid0l); - mac_hi = readl(&cdev->macid0h); - mac_addr[0] = mac_hi & 0xFF; - mac_addr[1] = (mac_hi & 0xFF00) >> 8; - mac_addr[2] = (mac_hi & 0xFF0000) >> 16; - mac_addr[3] = (mac_hi & 0xFF000000) >> 24; - mac_addr[4] = mac_lo & 0xFF; - mac_addr[5] = (mac_lo & 0xFF00) >> 8; - - if (!env_get("ethaddr")) { - if (!mac) { - printf(" not set. validating E-fuse MAC ... "); - if (is_valid_ethaddr((const u8 *)mac_addr)) - mac = (const char *)mac_addr; - } - - if (mac) { - printf("using: %pM on ", mac); - eth_env_set_enetaddr("ethaddr", (const u8 *)mac); - } - } - writel(MII_MODE_ENABLE, &cdev->miisel); - cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII; - cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII; - - rv = cpsw_register(&cpsw_data); - if (rv < 0) { - printf("Error %d registering CPSW switch\n", rv); - return 0; - } - return rv; -} -#endif /* defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD) */ -#if defined(CONFIG_MMC) -int board_mmc_init(bd_t *bis) -{ - int rc = 0; - - rc |= omap_mmc_init(0, 0, 0, -1, -1); - rc |= omap_mmc_init(1, 0, 0, -1, -1); - - return rc; -} -#endif int overwrite_console(void) { return 1; diff --git a/configs/brppt1_mmc_defconfig b/configs/brppt1_mmc_defconfig index 6bb4657113..3a83ecf1ac 100644 --- a/configs/brppt1_mmc_defconfig +++ b/configs/brppt1_mmc_defconfig @@ -3,13 +3,18 @@ CONFIG_ARCH_OMAP2PLUS=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_AM33XX=y CONFIG_TARGET_BRPPT1=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y +# CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-mmc" +CONFIG_TPL_SYS_MALLOC_F_LEN=0x0 +# CONFIG_EXPERT is not set +# CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y -CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT" CONFIG_BOOTDELAY=0 CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="run b_default" @@ -20,8 +25,9 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y CONFIG_SPL_I2C_SUPPORT=y -# CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y @@ -34,29 +40,56 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y -# CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y CONFIG_CMD_USB=y # CONFIG_CMD_ITEST is not set -# CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y # CONFIG_CMD_NFS is not set +CONFIG_CMD_MII=y CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_BKOPS_ENABLE=y +CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas " CONFIG_ENV_IS_IN_MMC=y -CONFIG_NETCONSOLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +# CONFIG_OF_TRANSLATE is not set CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_DM_I2C_COMPAT=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_MISC=y +CONFIG_DM_MMC=y CONFIG_MMC_OMAP_HS=y +CONFIG_PHY_NATSEMI=y +CONFIG_DM_ETH=y CONFIG_DRIVER_TI_CPSW=y +# CONFIG_NETDEVICES is not set +CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_TI=y CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y +CONFIG_USB_GADGET=y CONFIG_FAT_WRITE=y -CONFIG_OF_LIBFDT=y +CONFIG_LZO=y +# CONFIG_OF_LIBFDT_OVERLAY is not set +# CONFIG_EFI_LOADER is not set diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig index 7846e55313..342d31a183 100644 --- a/configs/brppt1_nand_defconfig +++ b/configs/brppt1_nand_defconfig @@ -3,12 +3,16 @@ CONFIG_ARCH_OMAP2PLUS=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_AM33XX=y CONFIG_TARGET_BRPPT1=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-nand" +CONFIG_TPL_SYS_MALLOC_F_LEN=0x0 +# CONFIG_EXPERT is not set +# CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y -CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1" CONFIG_BOOTDELAY=0 CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="run b_default" @@ -19,6 +23,9 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y @@ -32,15 +39,17 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y -# CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set CONFIG_CMD_NAND=y +CONFIG_CMD_PART=y CONFIG_CMD_USB=y # CONFIG_CMD_ITEST is not set -# CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y # CONFIG_CMD_NFS is not set +CONFIG_CMD_MII=y CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y @@ -49,16 +58,42 @@ CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0" CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(MLO),128k(cfgscr),128k(dtb),128k(u-boot-env),512k(u-boot),4m(kernel),128m(rootfs),-(user)" +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas " CONFIG_ENV_IS_IN_NAND=y -CONFIG_NETCONSOLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +# CONFIG_OF_TRANSLATE is not set +CONFIG_BLK=y CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_DM_I2C_COMPAT=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_MISC=y # CONFIG_MMC is not set CONFIG_NAND=y +CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y +CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 +CONFIG_PHY_NATSEMI=y +CONFIG_DM_ETH=y CONFIG_DRIVER_TI_CPSW=y +# CONFIG_NETDEVICES is not set +CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_TI=y CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y +CONFIG_USB_GADGET=y CONFIG_FAT_WRITE=y -CONFIG_OF_LIBFDT=y +CONFIG_LZO=y +# CONFIG_OF_LIBFDT_OVERLAY is not set +# CONFIG_EFI_LOADER is not set diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig index f4197c41a2..826a93c691 100644 --- a/configs/brppt1_spi_defconfig +++ b/configs/brppt1_spi_defconfig @@ -3,15 +3,18 @@ CONFIG_ARCH_OMAP2PLUS=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x4000 CONFIG_AM33XX=y CONFIG_TARGET_BRPPT1=y -CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y +CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-spi" +CONFIG_TPL_SYS_MALLOC_F_LEN=0x0 +# CONFIG_EXPERT is not set +# CONFIG_FIT is not set CONFIG_OF_BOARD_SETUP=y -CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT" CONFIG_SPI_BOOT=y CONFIG_BOOTDELAY=0 CONFIG_USE_BOOTCOMMAND=y @@ -23,6 +26,9 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_ARCH_MISC_INIT=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y +# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set CONFIG_SPL_I2C_SUPPORT=y # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_POWER_SUPPORT=y @@ -38,37 +44,65 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y -# CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y CONFIG_CMD_SF=y -CONFIG_CMD_SPI=y CONFIG_CMD_USB=y # CONFIG_CMD_ITEST is not set -# CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y # CONFIG_CMD_NFS is not set +CONFIG_CMD_MII=y CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_BKOPS_ENABLE=y +CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y -CONFIG_CMD_MTDPARTS=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas " CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_NETCONSOLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +# CONFIG_OF_TRANSLATE is not set CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_DM_GPIO=y +CONFIG_DM_I2C=y +CONFIG_DM_I2C_COMPAT=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_MISC=y +CONFIG_DM_MMC=y CONFIG_MMC_OMAP_HS=y +CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y # CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHY_NATSEMI=y +CONFIG_DM_ETH=y CONFIG_DRIVER_TI_CPSW=y +# CONFIG_NETDEVICES is not set +CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_SPI=y +CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_MUSB_HOST=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_MUSB_TI=y CONFIG_USB_MUSB_DSPS=y CONFIG_USB_STORAGE=y +CONFIG_USB_GADGET=y CONFIG_FAT_WRITE=y -CONFIG_OF_LIBFDT=y +CONFIG_LZO=y +# CONFIG_OF_LIBFDT_OVERLAY is not set +# CONFIG_EFI_LOADER is not set diff --git a/include/configs/brppt1.h b/include/configs/brppt1.h index d5b25730f5..aa476f6355 100644 --- a/include/configs/brppt1.h +++ b/include/configs/brppt1.h @@ -37,13 +37,13 @@ #endif /* CONFIG_EMMC_BOOT */ /* - * When we have SPI or NAND flash we expect to be making use of mtdparts, + * When we have NAND flash we expect to be making use of mtdparts, * both for ease of use in U-Boot and for passing information on to * the Linux kernel. */ -#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND) +#if defined(CONFIG_NAND) #define CONFIG_MTD_DEVICE /* Required for mtdparts */ -#endif /* CONFIG_SPI_BOOT, ... */ +#endif #ifdef CONFIG_NAND #define CONFIG_SPL_NAND_BASE @@ -95,7 +95,7 @@ "b_tgts_pme=net usb0 mmc0 mmc1\0" \ "loaddev=mmc 1\0" -#ifdef CONFIG_MMC +#ifdef CONFIG_ENV_IS_IN_MMC #define MMCTGTS \ MMCSPI_TGTS \ "cfgscr=mmc dev 1; mmc read ${cfgaddr} 200 80; source ${cfgaddr}\0" @@ -167,37 +167,32 @@ NANDTGTS \ #define CONFIG_SYS_NAND_ECCBYTES 14 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #define CONFIG_NAND_OMAP_GPMC_WSCFG 1 #endif /* CONFIG_NAND */ /* USB configuration */ #define CONFIG_USB_MUSB_DISABLE_BULK_COMBINE_SPLIT -#define CONFIG_AM335X_USB0 -#define CONFIG_AM335X_USB0_MODE MUSB_HOST -#define CONFIG_AM335X_USB1 -#define CONFIG_AM335X_USB1_MODE MUSB_HOST -#if defined(CONFIG_SPI_BOOT) -/* McSPI IP block */ -#define CONFIG_SF_DEFAULT_SPEED 24000000 - -#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#if defined(CONFIG_SPI) +/* SPI Flash */ +#define CONFIG_SF_DEFAULT_SPEED 24000000 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000 +/* Environment */ #define CONFIG_SYS_REDUNDAND_ENVIRONMENT -#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED -#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */ -#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */ -#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */ - -#elif defined(CONFIG_EMMC_BOOT) +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE +#define CONFIG_ENV_OFFSET 0x20000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ + CONFIG_ENV_SECT_SIZE) +#elif defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_SYS_MMC_ENV_DEV 1 #define CONFIG_SYS_MMC_ENV_PART 2 #define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #define CONFIG_SYS_REDUNDAND_ENVIRONMENT -#elif defined(CONFIG_NAND) +#elif defined(CONFIG_ENV_IS_IN_NAND) /* No NAND env support in SPL */ #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h index bdcbee4fc1..926ba9918c 100644 --- a/include/configs/bur_am335x_common.h +++ b/include/configs/bur_am335x_common.h @@ -11,6 +11,19 @@ #ifndef __BUR_AM335X_COMMON_H__ #define __BUR_AM335X_COMMON_H__ /* ------------------------------------------------------------------------- */ + +/* legacy #defines for non DM bur-board */ +#ifndef CONFIG_DM +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK (48000000) +#define CONFIG_SYS_NS16550_COM1 0x44e09000 + +#define CONFIG_I2C +#define CONFIG_SYS_I2C + +#endif /* CONFIG_DM */ + #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ /* Timer information */ @@ -20,16 +33,6 @@ #include -/* NS16550 Configuration */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK 48000000 -#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ - -/* Network defines */ -#define CONFIG_MII /* Required in net/eth.c */ -#define CONFIG_PHY_NATSEMI - /* * SPL related defines. The Public RAM memory map the ROM defines the * area between 0x402F0400 and 0x4030B800 as a download area and @@ -65,9 +68,6 @@ #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ GENERATED_GBL_DATA_SIZE) -/* I2C */ -#define CONFIG_SYS_I2C - /* * Our platforms make use of SPL to initalize the hardware (primarily * memory) enough for full U-Boot to be loaded. We also support Falcon