From: Konstantin Porotchkin <kostap@marvell.com>
Date: Fri, 25 May 2018 06:20:52 +0000 (+0800)
Subject: mvebu: pinctrl: Add SD/eMMC PHY selector to the driver
X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=f5db5979df6a6de12dcf634280d618bb32834ef9;p=u-boot.git

mvebu: pinctrl: Add SD/eMMC PHY selector to the driver

When the pin control driver selects SD/eMMC function for
a pin group, there is additional configuration to be done
for this case - switch the PHY to work with SDHCI interface.
This patch adds the missing functionality into the pin
control driver.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
---

diff --git a/drivers/pinctrl/mvebu/pinctrl-mvebu.c b/drivers/pinctrl/mvebu/pinctrl-mvebu.c
index 583262683f..0b9c9e1d6a 100644
--- a/drivers/pinctrl/mvebu/pinctrl-mvebu.c
+++ b/drivers/pinctrl/mvebu/pinctrl-mvebu.c
@@ -16,8 +16,48 @@
 #include <asm/arch-armada8k/soc-info.h>
 #include "pinctrl-mvebu.h"
 
+#define AP_EMMC_PHY_CTRL_REG		0x100
+#define CP_EMMC_PHY_CTRL_REG		0x424
+#define EMMC_PHY_CTRL_SDPHY_EN		BIT(0)
+
+#define AP806_EMMC_CLK_PIN_ID		0
+#define AP806_EMMC_CLK_FUNC		0x1
+#define CP110_EMMC_CLK_PIN_ID		56
+#define CP110_EMMC_CLK_FUNC		0xe
+
 DECLARE_GLOBAL_DATA_PTR;
 
+/* mvebu_pinctl_emmc_set_mux: configure sd/mmc PHY mux
+ * To enable SDIO/eMMC in Armada-APN806/CP110, need to configure PHY mux.
+ * eMMC/SD PHY register responsible for muxing between MPPs and SD/eMMC
+ * controller:
+ * - Bit0 enabled SDIO/eMMC PHY is used as a MPP muxltiplexer,
+ * - Bit0 disabled SDIO/eMMC PHY is connected to SDIO/eMMC controller
+ * If pin function is set to eMMC/SD, then configure the eMMC/SD PHY
+ * muxltiplexer register to be on SDIO/eMMC controller
+ */
+void mvebu_pinctl_emmc_set_mux(struct udevice *dev, u32 pin, u32 func)
+{
+	const void *blob = gd->fdt_blob;
+	int node = dev_of_offset(dev);
+	struct mvebu_pinctrl_priv *priv = dev_get_priv(dev);
+
+	if (!fdt_node_check_compatible(blob, node, "marvell,ap806-pinctrl")) {
+		if ((pin == AP806_EMMC_CLK_PIN_ID) &&
+		    (func == AP806_EMMC_CLK_FUNC)) {
+			clrbits_le32(priv->base_reg + AP_EMMC_PHY_CTRL_REG,
+				     EMMC_PHY_CTRL_SDPHY_EN);
+		}
+	} else if (!fdt_node_check_compatible(blob, node,
+					"marvell,armada-8k-cpm-pinctrl")) {
+		if ((pin == CP110_EMMC_CLK_PIN_ID) &&
+		    (func == CP110_EMMC_CLK_FUNC)) {
+			clrbits_le32(priv->base_reg + CP_EMMC_PHY_CTRL_REG,
+				     EMMC_PHY_CTRL_SDPHY_EN);
+		}
+	}
+}
+
 /*
  * mvebu_pinctrl_set_state: configure pin functions.
  * @dev: the pinctrl device to be configured.
@@ -47,9 +87,16 @@ int mvebu_pinctrl_set_state(struct udevice *dev, struct udevice *config)
 
 	function = fdtdec_get_int(blob, node, "marvell,function", 0xff);
 
+	/*
+	 * Check if setup of PHY mux is needed for this pins group.
+	 * Only the first pin id in array is tested, all the rest use the same
+	 * pin function.
+	 */
+	mvebu_pinctl_emmc_set_mux(dev, pin_arr[0], function);
+
 	for (i = 0; i < pin_count; i++) {
-	int reg_offset;
-	int field_offset;
+		int reg_offset;
+		int field_offset;
 		int pin = pin_arr[i];
 
 		if (function > priv->max_func) {
@@ -96,6 +143,14 @@ static int mvebu_pinctrl_set_state_all(struct udevice *dev,
 		return -EINVAL;
 	}
 
+	/* Check if setup of PHY mux is needed for this pins group. */
+	if (priv->pin_cnt < CP110_EMMC_CLK_PIN_ID)
+		mvebu_pinctl_emmc_set_mux(dev, AP806_EMMC_CLK_PIN_ID,
+					  func_arr[AP806_EMMC_CLK_PIN_ID]);
+	else
+		mvebu_pinctl_emmc_set_mux(dev, CP110_EMMC_CLK_PIN_ID,
+					  func_arr[CP110_EMMC_CLK_PIN_ID]);
+
 	for (pin = 0; pin < priv->pin_cnt; pin++) {
 		int reg_offset;
 		int field_offset;