From: Parthiban Nallathambi Date: Wed, 10 Apr 2019 14:35:32 +0000 (+0200) Subject: imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=d2d1191843e4265a1228a2f2b319f9cd31854de2;p=u-boot.git imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063) with eMMC on SoM. CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 38C Reset cause: POR Model: Phytec phyBOARD-i.MX6ULL-Segin SBC Board: PHYTEC phyCORE-i.MX6ULL DRAM: 256 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial@02020000 Out: serial@02020000 Err: serial@02020000 Net: FEC0 Working: - Eth0 - i2C - MMC/SD - eMMC - UART (1 & 5) - USB (host & otg) Signed-off-by: Parthiban Nallathambi --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index f01ff9f17c..24a409d7d1 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -589,6 +589,7 @@ dtb-$(CONFIG_MX6UL) += \ dtb-$(CONFIG_MX6ULL) += \ imx6ull-14x14-evk.dtb \ imx6ull-colibri.dtb \ + imx6ull-phycore-segin.dtb \ imx6ull-dart-6ul.dtb dtb-$(CONFIG_ARCH_MX6) += \ diff --git a/arch/arm/dts/imx6ul-phycore-segin.dts b/arch/arm/dts/imx6ul-phycore-segin.dts index a46012e2b4..7d68bf8430 100644 --- a/arch/arm/dts/imx6ul-phycore-segin.dts +++ b/arch/arm/dts/imx6ul-phycore-segin.dts @@ -16,7 +16,8 @@ /dts-v1/; -#include "imx6ul-pcl063.dtsi" +#include "imx6ul.dtsi" +#include "pcl063-common.dtsi" / { model = "Phytec phyBOARD-i.MX6UL-Segin SBC"; @@ -24,6 +25,10 @@ "fsl,imx6ul"; }; +&gpmi { + status = "okay"; +}; + &i2c1 { i2c_rtc: rtc@68 { compatible = "microcrystal,rv4162"; diff --git a/arch/arm/dts/imx6ull-phycore-segin.dts b/arch/arm/dts/imx6ull-phycore-segin.dts new file mode 100644 index 0000000000..6df3ad2e4a --- /dev/null +++ b/arch/arm/dts/imx6ull-phycore-segin.dts @@ -0,0 +1,70 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2019 Parthiban Nallathambi + */ + +/dts-v1/; + +#include "imx6ull.dtsi" +#include "pcl063-common.dtsi" + +/ { + model = "Phytec phyBOARD-i.MX6ULL-Segin SBC"; + compatible = "phytec,phyboard-imx6ull-segin", "phytec,imx6ull-pcl063", + "fsl,imx6ull"; +}; + +&i2c1 { + i2c_rtc: rtc@68 { + compatible = "microcrystal,rv4162"; + reg = <0x68>; + status = "okay"; + }; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + uart-has-rtscts; + status = "okay"; +}; + +&usdhc2 { + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1 + MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1 + MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x1b0b1 + MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059 + >; + }; + +}; diff --git a/arch/arm/dts/imx6ul-pcl063.dtsi b/arch/arm/dts/pcl063-common.dtsi similarity index 83% rename from arch/arm/dts/imx6ul-pcl063.dtsi rename to arch/arm/dts/pcl063-common.dtsi index 24a6a47983..2b14b2dc5f 100644 --- a/arch/arm/dts/imx6ul-pcl063.dtsi +++ b/arch/arm/dts/pcl063-common.dtsi @@ -7,10 +7,6 @@ * Author: Christian Hemp */ -/dts-v1/; - -#include "imx6ul.dtsi" - / { model = "Phytec phyCORE-i.MX6 Ultra Lite SOM"; compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul"; @@ -47,7 +43,7 @@ pinctrl-0 = <&pinctrl_gpmi_nand>; nand-on-flash-bbt; fsl,no-blockmark-swap; - status = "okay"; + status = "disabled"; #address-cells = <1>; #size-cells = <1>; @@ -99,6 +95,18 @@ status = "okay"; }; +&usdhc2 { + u-boot,dm-spl; + u-boot,dm-pre-reloc; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <8>; + no-1-8-v; + non-removable; + keep-power-in-suspend; + status = "disabled"; +}; + &iomuxc { pinctrl-names = "default"; @@ -170,4 +178,19 @@ >; }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9 + MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9 + MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9 + MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9 + >; + }; }; diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index f513c4c06f..baccc0b7a2 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -455,6 +455,18 @@ config TARGET_PCL063 select DM_THERMAL select SUPPORT_SPL +config TARGET_PCL063_ULL + bool "PHYTEC PCL063 (phyCORE-i.MX6ULL)" + select MX6ULL + select DM + select DM_ETH + select DM_GPIO + select DM_I2C + select DM_MMC + select DM_SERIAL + select DM_THERMAL + select SUPPORT_SPL + config TARGET_SECOMX6 bool "secomx6 boards" diff --git a/board/phytec/pcl063/Kconfig b/board/phytec/pcl063/Kconfig index 977db70f64..58f72f2791 100644 --- a/board/phytec/pcl063/Kconfig +++ b/board/phytec/pcl063/Kconfig @@ -10,3 +10,16 @@ config SYS_CONFIG_NAME default "pcl063" endif + +if TARGET_PCL063_ULL + +config SYS_BOARD + default "pcl063" + +config SYS_VENDOR + default "phytec" + +config SYS_CONFIG_NAME + default "pcl063_ull" + +endif diff --git a/board/phytec/pcl063/MAINTAINERS b/board/phytec/pcl063/MAINTAINERS index 037f243cb6..710b9680d4 100644 --- a/board/phytec/pcl063/MAINTAINERS +++ b/board/phytec/pcl063/MAINTAINERS @@ -1,9 +1,14 @@ PCL063 BOARD M: Martyn Welch +M: Parthiban Nallathambi S: Maintained F: arch/arm/dts/imx6ul-pcl063.dtsi F: arch/arm/dts/imx6ul-phycore-segin.dts +F: arch/arm/dts/imx6ull-phycore-segin.dts +F: arch/arm/dts/pcl063-common.dtsi F: arch/arm/dts/imx6ull-u-boot.dtsi F: board/phytec/pcl063/ F: configs/phycore_pcl063_defconfig +F: configs/phycore_pcl063_ull_defconfig F: include/configs/pcl063.h +F: include/configs/pcl063_ull.h diff --git a/board/phytec/pcl063/pcl063.c b/board/phytec/pcl063/pcl063.c index 38b233d1b0..17012df037 100644 --- a/board/phytec/pcl063/pcl063.c +++ b/board/phytec/pcl063/pcl063.c @@ -200,7 +200,10 @@ int board_init(void) int checkboard(void) { - puts("Board: PHYTEC phyCORE-i.MX6UL\n"); + u32 cpurev = get_cpu_rev(); + + printf("Board: PHYTEC phyCORE-i.MX%s\n", + get_imx_type((cpurev & 0xFF000) >> 12)); return 0; } diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c index b93cd493f2..73a774645d 100644 --- a/board/phytec/pcl063/spl.c +++ b/board/phytec/pcl063/spl.c @@ -13,6 +13,7 @@ #include #include #include +#include #include /* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8 -> 256MiB */ @@ -117,11 +118,32 @@ static iomux_v3_cfg_t const usdhc1_pads[] = { MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; +#ifndef CONFIG_NAND_MXS +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; +#endif + static struct fsl_esdhc_cfg usdhc_cfg[] = { { .esdhc_base = USDHC1_BASE_ADDR, .max_bus_width = 4, }, +#ifndef CONFIG_NAND_MXS + { + .esdhc_base = USDHC2_BASE_ADDR, + .max_bus_width = 8, + }, +#endif }; int board_mmc_getcd(struct mmc *mmc) @@ -131,12 +153,58 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { - imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); - - return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); + int i, ret; + + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + SETUP_IOMUX_PADS(usdhc1_pads); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; +#ifndef CONFIG_NAND_MXS + case 1: + SETUP_IOMUX_PADS(usdhc2_pads); + usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; +#endif + default: + printf("Warning - USDHC%d controller not supporting\n", + i + 1); + return 0; + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + + return 0; } +void board_boot_order(u32 *spl_boot_list) +{ + u32 bmode = imx6_src_get_boot_mode(); + u8 boot_dev = BOOT_DEVICE_MMC1; + + switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) { + case IMX6_BMODE_SD: + case IMX6_BMODE_ESD: + boot_dev = BOOT_DEVICE_MMC1; + break; + case IMX6_BMODE_MMC: + case IMX6_BMODE_EMMC: + boot_dev = BOOT_DEVICE_MMC2; + break; + default: + /* Default - BOOT_DEVICE_MMC1 */ + printf("Wrong board boot order\n"); + break; + } + + spl_boot_list[0] = boot_dev; +} #endif /* CONFIG_FSL_ESDHC */ void board_init_f(ulong dummy) diff --git a/configs/phycore_pcl063_ull_defconfig b/configs/phycore_pcl063_ull_defconfig new file mode 100644 index 0000000000..75408a8344 --- /dev/null +++ b/configs/phycore_pcl063_ull_defconfig @@ -0,0 +1,54 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_TARGET_PCL063_ULL=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL=y +# CONFIG_CMD_DEKBLOB is not set +CONFIG_DISTRO_DEFAULTS=y +CONFIG_NR_DRAM_BANKS=8 +CONFIG_FIT=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" +CONFIG_BOOTDELAY=3 +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +# CONFIG_RANDOM_UUID is not set +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_CACHE=y +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ull-phycore-segin" +CONFIG_DM_I2C_GPIO=y +CONFIG_SYS_I2C_MXC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_PMIC=y +# CONFIG_SPL_PMIC_CHILDREN is not set +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_MXC_UART=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Phytec" +CONFIG_USB_GADGET_VENDOR_NUM=0x01b67 +CONFIG_USB_GADGET_PRODUCT_NUM=0x4fff +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_LZO=y diff --git a/include/configs/pcl063.h b/include/configs/pcl063.h index 12d8d67f0f..8fef250ac4 100644 --- a/include/configs/pcl063.h +++ b/include/configs/pcl063.h @@ -22,6 +22,8 @@ * Tweak the SPL text base address to avoid this. */ +#define CONFIG_SYS_FSL_USDHC_NUM 1 + /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M) diff --git a/include/configs/pcl063_ull.h b/include/configs/pcl063_ull.h new file mode 100644 index 0000000000..0f1a010b4e --- /dev/null +++ b/include/configs/pcl063_ull.h @@ -0,0 +1,117 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Board configuration file for Phytec phyBOARD-i.MX6ULL-Segin SBC + * Copyright (C) 2019 Parthiban Nallathambi + * + * Based on include/configs/xpress.h: + * Copyright (C) 2015-2016 Stefan Roese + */ +#ifndef __PCL063_ULL_H +#define __PCL063_ULL_H + +#include +#include "mx6_common.h" + +/* SPL options */ +#include "imx6_spl.h" + +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M) + +/* Environment settings */ +#define CONFIG_ENV_SIZE (0x4000) +#define CONFIG_ENV_OFFSET (0x80000) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_OFFSET_REDUND \ + (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) + +/* Environment in SD */ +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 0 +#define MMC_ROOTFS_DEV 0 +#define MMC_ROOTFS_PART 2 + +/* Console configs */ +#define CONFIG_MXC_UART_BASE UART1_BASE + +/* MMC Configs */ +#define CONFIG_FSL_USDHC + +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR +#define CONFIG_SUPPORT_EMMC_BOOT + +/* I2C configs */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000000) + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define PHYS_SDRAM_SIZE SZ_256M + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* NAND */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x40000000 + +/* USB Configs */ +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +#define CONFIG_IMX_THERMAL + +#define ENV_MMC \ + "mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \ + "mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \ + "fitpart=1\0" \ + "bootdelay=3\0" \ + "silent=1\0" \ + "optargs=rw rootwait\0" \ + "mmcautodetect=yes\0" \ + "mmcrootfstype=ext4\0" \ + "mmcfit_name=fitImage\0" \ + "mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \ + "${mmcfit_name}\0" \ + "mmcargs=setenv bootargs " \ + "root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \ + "console=${console} rootfstype=${mmcrootfstype}\0" \ + "mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \ + +/* Default environment */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fdt_high=0xffffffff\0" \ + "console=ttymxc0,115200n8\0" \ + "addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \ + "fit_addr=0x82000000\0" \ + ENV_MMC + +#define CONFIG_BOOTCOMMAND "run mmc_mmc_fit" + +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 0) \ + func(MMC, mmc, 1) \ + func(DHCP, dhcp, na) + +#include + +#endif /* __PCL063_ULL_H */