From: Walter Schweizer Date: Thu, 6 Oct 2016 21:29:56 +0000 (+0200) Subject: arm: kirkwood: add support for Synology DS109 board X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=a0a868b20b7e3a8bc331f32720516d0ba85d7df8;p=u-boot.git arm: kirkwood: add support for Synology DS109 board Synology DS109 is based on MV88F6281. The code is based on Dreamplug code with modificatons from Synologys open source repository. Signed-off-by: Walter Schweizer Signed-off-by: Stefan Roese --- diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index 9205b1e164..9c24921b5c 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -10,6 +10,9 @@ config TARGET_OPENRD config TARGET_DREAMPLUG bool "DreamPlug Board" +config TARGET_DS109 + bool "Synology DS109" + config TARGET_GURUPLUG bool "GuruPlug Board" @@ -59,6 +62,7 @@ config SYS_SOC source "board/Marvell/openrd/Kconfig" source "board/Marvell/dreamplug/Kconfig" +source "board/Synology/ds109/Kconfig" source "board/Marvell/guruplug/Kconfig" source "board/Marvell/sheevaplug/Kconfig" source "board/buffalo/lsxl/Kconfig" diff --git a/board/Synology/ds109/Kconfig b/board/Synology/ds109/Kconfig new file mode 100644 index 0000000000..a7c75ae368 --- /dev/null +++ b/board/Synology/ds109/Kconfig @@ -0,0 +1,12 @@ +if TARGET_DS109 + +config SYS_BOARD + default "ds109" + +config SYS_VENDOR + default "Synology" + +config SYS_CONFIG_NAME + default "ds109" + +endif diff --git a/board/Synology/ds109/Makefile b/board/Synology/ds109/Makefile new file mode 100644 index 0000000000..eeeb64d011 --- /dev/null +++ b/board/Synology/ds109/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := ds109.o diff --git a/board/Synology/ds109/ds109.c b/board/Synology/ds109/ds109.c new file mode 100644 index 0000000000..8ab1387d1d --- /dev/null +++ b/board/Synology/ds109/ds109.c @@ -0,0 +1,169 @@ +/* + * Copyright (C) 2009-2012 + * Wojciech Dubowik + * Luka Perkov + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include "ds109.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(DS109_OE_VAL_LOW, + DS109_OE_VAL_HIGH, + DS109_OE_LOW, DS109_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_SPI_SCn, /* SPI Flash */ + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP4_GPIO, + MPP5_GPO, + MPP6_SYSRST_OUTn, /* Reset signal */ + MPP7_GPO, + MPP8_TW_SDA, /* I2C */ + MPP9_TW_SCK, /* I2C */ + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, + MPP13_UART1_TXD, + MPP14_UART1_RXD, + MPP15_GPIO, + MPP16_GPIO, + MPP17_GPIO, + MPP18_GPO, + MPP19_GPO, + MPP20_SATA1_ACTn, + MPP21_SATA0_ACTn, + MPP22_GPIO, /* HDD2 FAIL LED */ + MPP23_GPIO, /* HDD1 FAIL LED */ + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GPIO, + MPP31_GPIO, /* HDD2 */ + MPP32_GPIO, /* FAN A */ + MPP33_GPIO, /* FAN B */ + MPP34_GPIO, /* FAN C */ + MPP35_GPIO, /* FAN SENSE */ + MPP36_GPIO, + MPP37_GPIO, + MPP38_GPIO, + MPP39_GPIO, + MPP40_GPIO, + MPP41_GPIO, + MPP42_GPIO, + MPP43_GPIO, + MPP44_GPIO, + MPP45_GPIO, + MPP46_GPIO, + MPP47_GPIO, + MPP48_GPIO, + MPP49_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + return 0; +} + +/* Synology reset uses UART */ +#include +#define SOFTWARE_SHUTDOWN 0x31 +#define SOFTWARE_REBOOT 0x43 +#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE +void reset_misc(void) +{ + int b_d; + printf("Synology reset..."); + udelay(50000); + + b_d = ns16550_calc_divisor((NS16550_t)CONFIG_SYS_NS16550_COM2, + CONFIG_SYS_NS16550_CLK, 9600); + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM2, b_d); + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM2, SOFTWARE_REBOOT); +} + +/* Support old kernels */ +void setup_board_tags(struct tag **in_params) +{ + unsigned int boardId; + struct tag *params; + struct tag_mv_uboot *t; + + printf("Synology board tags..."); + params = *in_params; + t = (struct tag_mv_uboot *)¶ms->u; + + t->uboot_version = VER_NUM; + + boardId = SYNO_DS109_ID; + t->uboot_version |= boardId; + + t->tclk = CONFIG_SYS_TCLK; + t->sysclk = CONFIG_SYS_TCLK*2; + + params->hdr.tag = ATAG_MV_UBOOT; + params->hdr.size = tag_size(tag_mv_uboot); + params = tag_next(params); + *in_params = params; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116 PHY */ +void reset_phy(void) +{ + u16 reg; + u16 devadr; + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { + printf("Error: 88E1116 could not read PHY dev address\n"); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf("88E1116 Initialized on %s\n", name); +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Synology/ds109/ds109.h b/board/Synology/ds109/ds109.h new file mode 100644 index 0000000000..95d924cf1f --- /dev/null +++ b/board/Synology/ds109/ds109.h @@ -0,0 +1,44 @@ +/* + * Copyright (C) 2009-2012 + * Wojciech Dubowik + * Luka Perkov + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __DS109_H +#define __DS109_H + +#define DS109_OE_LOW (~(0)) +#define DS109_OE_HIGH (~(0)) +#define DS109_OE_VAL_LOW ((1 << 22)|(1 << 23)) +#define DS109_OE_VAL_HIGH ((1 << 1)|1) + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_MAC_CTRL2_REG 21 + +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +/* Marvell uboot parameters */ +#define ATAG_MV_UBOOT 0x41000403 +#define VER_NUM 0x03040400 /* 3.4.4 */ +#define BOARD_ID_BASE 0x0 +#define SYNO_DS109_ID (BOARD_ID_BASE+0x15) + +struct tag_mv_uboot { + u32 uboot_version; + u32 tclk; + u32 sysclk; + u32 isusbhost; + char macaddr[4][6]; + u16 mtu[4]; + u32 fw_image_base; + u32 fw_image_size; +}; + +#endif /* __DS109_H */ diff --git a/board/Synology/ds109/kwbimage.cfg b/board/Synology/ds109/kwbimage.cfg new file mode 100644 index 0000000000..19d77e3a1f --- /dev/null +++ b/board/Synology/ds109/kwbimage.cfg @@ -0,0 +1,147 @@ +# +# (C) Copyright 2011 +# Jason Cooper +# +# Based on work by: +# Marvell Semiconductor +# Written-by: Siddarth Gore +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0/1 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b9b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 01, Cs0width=x8 +# bit3-2: 10, Cs0size=1Gb +# bit5-4: 01, Cs1width=x8 +# bit7-6: 10, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/Synology/ds109/openocd.cfg b/board/Synology/ds109/openocd.cfg new file mode 100644 index 0000000000..baa512aef2 --- /dev/null +++ b/board/Synology/ds109/openocd.cfg @@ -0,0 +1,115 @@ +# Synology DS109 + +interface ftdi +ftdi_vid_pid 0x0403 0x6010 + +ftdi_layout_init 0x0008 0x000b +ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010 +ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040 + +adapter_khz 2000 + +# length of reset signal: [ms] +adapter_nsrst_assert_width 1000 + +# don't talk to JTAG after reset for: [ms] +adapter_nsrst_delay 200 + +source [find target/feroceon.cfg] + +reset_config trst_and_srst srst_nogate + +proc ds109_init { } { + + # We need to assert DBGRQ while holding nSRST down. + # However DBGACK will be set only when nSRST is released. + # Furthermore, the JTAG interface doesn't respond at all when + # the CPU is in the WFI (wait for interrupts) state, so it is + # possible that initial tap examination failed. So let's + # re-examine the target again here when nSRST is asserted which + # should then succeed. + jtag_reset 0 1 + feroceon.cpu arp_examine + halt 0 + jtag_reset 0 0 + wait_halt + #reset run + #soft_reset_halt + + arm mcr 15 0 0 1 0 0x00052078 + + mww 0xD00100e0 0x1b1b1b9b ;# + mww 0xD0020134 0xbbbbbbbb ;# + mww 0xD0020138 0x00bbbbbb ;# + mww 0xD0001400 0x43000C30 ;# DDR SDRAM Configuration Register + mww 0xD0001404 0x39743000 ;# Dunit Control Low Register + mww 0xD0001408 0x22125551 ;# DDR SDRAM Timing (Low) Register + mww 0xD000140C 0x00000833 ;# DDR SDRAM Timing (High) Register + mww 0xD0001410 0x0000000d ;# DDR SDRAM Address Control Register + mww 0xD0001414 0x00000000 ;# DDR SDRAM Open Pages Control Register + mww 0xD0001418 0x00000000 ;# DDR SDRAM Operation Register + mww 0xD000141C 0x00000C62 ;# DDR SDRAM Mode Register + mww 0xD0001420 0x00000042 ;# DDR SDRAM Extended Mode Register + mww 0xD0001424 0x0000F1FF ;# Dunit Control High Register + mww 0xD0001428 0x00085520 ;# Dunit Control High Register + mww 0xD000147c 0x00008552 ;# Dunit Control High Register + mww 0xD0001500 0x00000000 ;# + mww 0xD0001504 0x07FFFFF1 ;# CS0n Size Register + mww 0xD0001508 0x10000000 ;# CS1n Base Register + mww 0xD000150C 0x00000000 ;# CS1n Size Register + mww 0xD0001510 0x20000000 ;# + mww 0xD0001514 0x00000000 ;# CS2n Size Register + mww 0xD000151C 0x00000000 ;# CS3n Size Register + mww 0xD0001494 0x003C0000 ;# DDR2 SDRAM ODT Control (Low) Register + mww 0xD0001498 0x00000000 ;# DDR2 SDRAM ODT Control (High) REgister + mww 0xD000149C 0x0000F80F ;# DDR2 Dunit ODT Control Register + mww 0xD0001480 0x00000001 ;# DDR SDRAM Initialization Control Register + mww 0xD0020204 0x00000000 ;# Main IRQ Interrupt Mask Register + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + mww 0xD0020204 0x00000000 ;# " + + mww 0xD0010000 0x01111111 ;# MPP 0 to 7 + mww 0xD0010004 0x11113322 ;# MPP 8 to 15 + mww 0xD0010008 0x00001111 ;# MPP 16 to 23 +} + +proc ds109_load { } { + # load u-Boot into RAM and execute it + ds109_init + load_image u-boot.bin 0x00600000 bin + resume 0x00600000 +} diff --git a/configs/ds109_defconfig b/configs/ds109_defconfig new file mode 100644 index 0000000000..34a4673c0f --- /dev/null +++ b/configs/ds109_defconfig @@ -0,0 +1,16 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_TARGET_DS109=y +CONFIG_HUSH_PARSER=y +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_DHCP=y +CONFIG_CMD_PING=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SYS_NS16550=y diff --git a/include/configs/ds109.h b/include/configs/ds109.h new file mode 100644 index 0000000000..222a510034 --- /dev/null +++ b/include/configs/ds109.h @@ -0,0 +1,103 @@ +/* + * (C) Copyright 2011 + * Jason Cooper + * + * Based on work by: + * Marvell Semiconductor + * Written-by: Siddarth Gore + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_DS109_H +#define _CONFIG_DS109_H + +/* + * FIXME: This belongs in mach-types.h. However, we only pull mach-types + * from Linus' kernel.org tree. This hasn't been updated primarily due to + * the recent arch/arm reshuffling. So, in the meantime, we'll place it + * here. + */ +#include +#ifdef MACH_TYPE_SYNOLOGY +#error "MACH_TYPE_SYNOLOGY has been defined properly, please remove this." +#else +#define MACH_TYPE_SYNOLOGY 527 +#endif + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ +#define CONFIG_MACH_TYPE MACH_TYPE_SYNOLOGY + +/* + * Commands configuration + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT + +/* + * mv-plug-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-plug-common.h" + +/* + * Environment variables configurations + */ +#ifdef CONFIG_SPI_FLASH +#define CONFIG_ENV_IS_IN_SPI_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ +#else +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#endif + +#ifdef CONFIG_CMD_SF +#define CONFIG_HARD_SPI 1 +#define CONFIG_KIRKWOOD_SPI 1 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ +#endif + +/* + * max 4k env size is enough, but in case of nand + * it has to be rounded to sector size + */ +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_ADDR 0x3d0000 +#define CONFIG_ENV_OFFSET 0x3d0000 /* env starts here */ + +/* + * Default environment variables + */ +#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ + "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ + "bootm 0x6400000;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "x_bootcmd_ethernet=ping 192.168.1.2\0" \ + "x_bootcmd_usb=usb start\0" \ + "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ + "x_bootargs=console=ttyS0,115200\0" \ + "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" \ + "ipaddr=192.168.1.5\0" + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_MVGBE_PORTS {1, 0} /* enable one port */ +#define CONFIG_PHY_BASE_ADR 8 +#endif /* CONFIG_CMD_NET */ + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ + +#endif /* _CONFIG_DS109_H */