From: Andre Przywara Date: Thu, 19 Oct 2023 14:51:39 +0000 (+0100) Subject: sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=95c3b0635ea4323c82e3f7ecdac69460897a907c;p=u-boot.git sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Sync the devicetree files from the official Linux kernel tree, v6.6-rc6. This is covering Allwinner SoCs with 64-bit ARM cores. Only small cosmetic changes (clock name fixed), but we add the DT for the new OrangePi Zero 3 board, for which U-Boot enablement patches are pending. As before, this omits the non-backwards compatible changes to the R_INTC controller, to remain compatible with older kernels. Signed-off-by: Andre Przywara Reviewed-by: Jernej Skrabec --- diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi index 135762b34f..2240eaec5d 100644 --- a/arch/arm/dts/sun50i-a64.dtsi +++ b/arch/arm/dts/sun50i-a64.dtsi @@ -93,6 +93,7 @@ L2: l2-cache { compatible = "cache"; cache-level = <2>; + cache-unified; }; }; @@ -407,7 +408,7 @@ interrupts = ; clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>; clock-names = "ahb", "tcon-ch0"; - clock-output-names = "tcon-pixel-clock"; + clock-output-names = "tcon-data-clock"; #clock-cells = <0>; resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>; reset-names = "lcd", "lvds"; diff --git a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts index 686f58e770..b710f1a0f5 100644 --- a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts +++ b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2019 Corentin LABBE */ diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi new file mode 100644 index 0000000000..15290e6892 --- /dev/null +++ b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi @@ -0,0 +1,134 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Arm Ltd. + * + * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3. + * Excludes PMIC nodes and properties, since they are different between the two. + */ + +#include "sun50i-h616.dtsi" + +#include +#include +#include + +/ { + aliases { + ethernet0 = &emac0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + function = LED_FUNCTION_POWER; + color = ; + gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ + default-state = "on"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ + }; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the USB-C socket */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v>; + enable-active-high; + gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ + }; +}; + +&ehci1 { + status = "okay"; +}; + +/* USB 2 & 3 are on headers only. */ + +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + allwinner,rx-delay-ps = <3100>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + +&mdio0 { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usbotg { + /* + * PHY0 pins are connected to a USB-C socket, but a role switch + * is not implemented: both CC pins are pulled to GND. + * The VBUS pins power the device, so a fixed peripheral mode + * is the best choice. + * The board can be powered via GPIOs, in this case port0 *can* + * act as a host (with a cable/adapter ignoring CC), as VBUS is + * then provided by the GPIOs. Any user of this setup would + * need to adjust the DT accordingly: dr_mode set to "host", + * enabling OHCI0 and EHCI0. + */ + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts index cb8600d0ea..d83852e72f 100644 --- a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts +++ b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts @@ -1,99 +1,23 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2020 Arm Ltd. */ /dts-v1/; -#include "sun50i-h616.dtsi" - -#include -#include -#include +#include "sun50i-h616-orangepi-zero.dtsi" / { model = "OrangePi Zero2"; compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616"; - - aliases { - ethernet0 = &emac0; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - leds { - compatible = "gpio-leds"; - - led-0 { - function = LED_FUNCTION_POWER; - color = ; - gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */ - default-state = "on"; - }; - - led-1 { - function = LED_FUNCTION_STATUS; - color = ; - gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */ - }; - }; - - reg_vcc5v: vcc5v { - /* board wide 5V supply directly from the USB-C socket */ - compatible = "regulator-fixed"; - regulator-name = "vcc-5v"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - }; - - reg_usb1_vbus: regulator-usb1-vbus { - compatible = "regulator-fixed"; - regulator-name = "usb1-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <®_vcc5v>; - enable-active-high; - gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */ - }; }; -&ehci1 { - status = "okay"; -}; - -/* USB 2 & 3 are on headers only. */ - &emac0 { - pinctrl-names = "default"; - pinctrl-0 = <&ext_rgmii_pins>; - phy-mode = "rgmii"; - phy-handle = <&ext_rgmii_phy>; phy-supply = <®_dcdce>; - allwinner,rx-delay-ps = <3100>; - allwinner,tx-delay-ps = <700>; - status = "okay"; -}; - -&mdio0 { - ext_rgmii_phy: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; }; &mmc0 { vmmc-supply = <®_dcdce>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ - bus-width = <4>; - status = "okay"; -}; - -&ohci1 { - status = "okay"; }; &r_rsb { @@ -211,44 +135,3 @@ vcc-ph-supply = <®_aldo1>; vcc-pi-supply = <®_aldo1>; }; - -&spi0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <40000000>; - }; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_ph_pins>; - status = "okay"; -}; - -&usbotg { - /* - * PHY0 pins are connected to a USB-C socket, but a role switch - * is not implemented: both CC pins are pulled to GND. - * The VBUS pins power the device, so a fixed peripheral mode - * is the best choice. - * The board can be powered via GPIOs, in this case port0 *can* - * act as a host (with a cable/adapter ignoring CC), as VBUS is - * then provided by the GPIOs. Any user of this setup would - * need to adjust the DT accordingly: dr_mode set to "host", - * enabling OHCI0 and EHCI0. - */ - dr_mode = "peripheral"; - status = "okay"; -}; - -&usbphy { - usb1_vbus-supply = <®_usb1_vbus>; - status = "okay"; -}; diff --git a/arch/arm/dts/sun50i-h616-x96-mate.dts b/arch/arm/dts/sun50i-h616-x96-mate.dts index 07424c28b6..959b6fd184 100644 --- a/arch/arm/dts/sun50i-h616-x96-mate.dts +++ b/arch/arm/dts/sun50i-h616-x96-mate.dts @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Copyright (C) 2021 Arm Ltd. */ diff --git a/arch/arm/dts/sun50i-h618-orangepi-zero3.dts b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts new file mode 100644 index 0000000000..00fe28caac --- /dev/null +++ b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts @@ -0,0 +1,94 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616-orangepi-zero.dtsi" + +/ { + model = "OrangePi Zero3"; + compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618"; +}; + +&emac0 { + phy-supply = <®_dldo1>; +}; + +&ext_rgmii_phy { + motorcomm,clk-out-frequency-hz = <125000000>; +}; + +&mmc0 { + /* + * The schematic shows the card detect pin wired up to PF6, via an + * inverter, but it just doesn't work. + */ + broken-cd; + vmmc-supply = <®_dldo1>; +}; + +&r_i2c { + status = "okay"; + + axp313: pmic@36 { + compatible = "x-powers,axp313a"; + reg = <0x36>; + #interrupt-cells = <1>; + interrupt-controller; + interrupt-parent = <&pio>; + interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */ + + vin1-supply = <®_vcc5v>; + vin2-supply = <®_vcc5v>; + vin3-supply = <®_vcc5v>; + + regulators { + /* Supplies VCC-PLL, so needs to be always on. */ + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + /* Supplies VCC-IO, so needs to be always on. */ + reg_dldo1: dldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3"; + }; + + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <990000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdc2: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-dram"; + }; + }; + }; +}; + +&pio { + vcc-pc-supply = <®_dldo1>; + vcc-pf-supply = <®_dldo1>; + vcc-pg-supply = <®_aldo1>; + vcc-ph-supply = <®_dldo1>; + vcc-pi-supply = <®_dldo1>; +}; diff --git a/include/dt-bindings/clock/sun50i-h6-ccu.h b/include/dt-bindings/clock/sun50i-h6-ccu.h index a1545cd60e..ef9123d819 100644 --- a/include/dt-bindings/clock/sun50i-h6-ccu.h +++ b/include/dt-bindings/clock/sun50i-h6-ccu.h @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2017 Icenowy Zheng */ diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h index 1191aca53a..6f8f01e676 100644 --- a/include/dt-bindings/clock/sun50i-h616-ccu.h +++ b/include/dt-bindings/clock/sun50i-h616-ccu.h @@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2020 Arm Ltd. */ diff --git a/include/dt-bindings/clock/sun6i-rtc.h b/include/dt-bindings/clock/sun6i-rtc.h index c845493e4d..3bd3aa3d57 100644 --- a/include/dt-bindings/clock/sun6i-rtc.h +++ b/include/dt-bindings/clock/sun6i-rtc.h @@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ #ifndef _DT_BINDINGS_CLK_SUN6I_RTC_H_ #define _DT_BINDINGS_CLK_SUN6I_RTC_H_ diff --git a/include/dt-bindings/reset/sun50i-h6-ccu.h b/include/dt-bindings/reset/sun50i-h6-ccu.h index 81106f4550..d038ddfa48 100644 --- a/include/dt-bindings/reset/sun50i-h6-ccu.h +++ b/include/dt-bindings/reset/sun50i-h6-ccu.h @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2017 Icenowy Zheng */ diff --git a/include/dt-bindings/reset/sun50i-h6-r-ccu.h b/include/dt-bindings/reset/sun50i-h6-r-ccu.h index 7950e799c7..d541ade884 100644 --- a/include/dt-bindings/reset/sun50i-h6-r-ccu.h +++ b/include/dt-bindings/reset/sun50i-h6-r-ccu.h @@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2016 Icenowy Zheng */ diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h index cb6285a8d1..1bd8bb0a11 100644 --- a/include/dt-bindings/reset/sun50i-h616-ccu.h +++ b/include/dt-bindings/reset/sun50i-h616-ccu.h @@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2020 Arm Ltd. */