From: Michal Suchanek Date: Thu, 4 Aug 2022 17:57:45 +0000 (+0200) Subject: doc: dm: clarify activation. X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=8f666cbb75bb0290fa7987def29e751a670a04ce;p=u-boot.git doc: dm: clarify activation. Explain when devices should get activated. Signed-off-by: Michal Suchanek Reviewed-by: Simon Glass Reviewed-by: Heinrich Schuchardt --- diff --git a/doc/develop/driver-model/design.rst b/doc/develop/driver-model/design.rst index a75d637ec3..20611e85e3 100644 --- a/doc/develop/driver-model/design.rst +++ b/doc/develop/driver-model/design.rst @@ -794,34 +794,53 @@ fall afoul of this rule. Activation/probe ^^^^^^^^^^^^^^^^ -When a device needs to be used, U-Boot activates it, by first reading ofdata -as above and then following these steps (see device_probe()): +To save resources devices in U-Boot are probed lazily. U-Boot is a bootloader, +not an operating system. Many devices are never used during an U-Boot run, and +probing them takes time, requires memory, may add delays to the main loop, etc. + +The device should be probed by the uclass code or generic device code (e.g. +device_find_global_by_ofnode()). Uclasses differ but two common use cases can be +seen: + + 1. The uclass is asked to look up a specific device, such as SPI bus 0, + first chip select - in this case the returned device should be + activated. + + 2. The uclass is asked to perform a specific function on any device that + supports it, eg. reset the board using any sysreset that can be found - + for this case the core uclass code provides iterators that activate + each device before returning it, and the uclass typically implements a + walk function that iterates over all devices of the uclass and tries + to perform the requested function on each in turn until succesful. + +To activate a device U-Boot first reads ofdata as above and then follows these +steps (see device_probe()): 1. All parent devices are probed. It is not possible to activate a device - unless its predecessors (all the way up to the root device) are activated. - This means (for example) that an I2C driver will require that its bus - be activated. + unless its predecessors (all the way up to the root device) are activated. + This means (for example) that an I2C driver will require that its bus + be activated. 2. The device's probe() method is called. This should do anything that - is required by the device to get it going. This could include checking - that the hardware is actually present, setting up clocks for the - hardware and setting up hardware registers to initial values. The code - in probe() can access: + is required by the device to get it going. This could include checking + that the hardware is actually present, setting up clocks for the + hardware and setting up hardware registers to initial values. The code + in probe() can access: - platform data in dev->plat (for configuration) - private data in dev->priv (for run-time state) - uclass data in dev->uclass_priv (for things the uclass stores about this device) - Note: If you don't use priv_auto then you will need to - allocate the priv space here yourself. The same applies also to - plat_auto. Remember to free them in the remove() method. + Note: If you don't use priv_auto then you will need to + allocate the priv space here yourself. The same applies also to + plat_auto. Remember to free them in the remove() method. 3. The device is marked 'activated' 4. The uclass's post_probe() method is called, if one exists. This may - cause the uclass to do some housekeeping to record the device as - activated and 'known' by the uclass. + cause the uclass to do some housekeeping to record the device as + activated and 'known' by the uclass. Running stage ^^^^^^^^^^^^^