From: Chris Morgan Date: Fri, 21 Apr 2023 15:59:19 +0000 (-0500) Subject: board: rockchip: add Anbernic RGXX3 Series Devices X-Git-Url: http://git.dujemihanovic.xyz/img/sics.gif?a=commitdiff_plain;h=6cf6fe25370c8d96e02488ef8779e295ecdb982d;p=u-boot.git board: rockchip: add Anbernic RGXX3 Series Devices The Anbernic RGxx3 is a "pseudo-device" that encompasses the following devices: - Anbernic RG353M - Anbernic RG353P - Anbernic RG353V - Anbernic RG353VS - Anbernic RG503 The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that is used for all RGxx3 devices. Via the board.c file, the bootloader automatically sets the correct fdtfile, board, and board_name environment variables so that the correct devicetree can be passed to Linux. It is also possible to simply hard-code a single devicetree in the boot.scr file and use that to load Linux as well. The common specifications for each device are: - Rockchip RK3566 SoC - 2 external SDMMC slots - 1 USB-C host port, 1 USB-C peripheral port - 1 mini-HDMI output - MIPI-DSI based display panel - ADC controlled joysticks with a GPIO mux - GPIO buttons - A PWM controlled vibrator - An ADC controlled button All of the common features are defined in the devicetree synced from upstream Linux. TODO: DSI panel auto-detection for the RG353 devices (requires porting of DSI controller driver and DSI-DPHY driver to send DSI commands to the panel). Signed-off-by: Chris Morgan Reviewed-by: Kever Yang --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 935b2f1517..c43d80443f 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -165,6 +165,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \ rk3399pro-rock-pi-n10.dtb dtb-$(CONFIG_ROCKCHIP_RK3568) += \ + rk3566-anbernic-rgxx3.dtb \ rk3568-evb.dtb \ rk3566-radxa-cm3-io.dtb \ rk3568-rock-3a.dtb diff --git a/arch/arm/dts/rk3566-anbernic-rgxx3-u-boot.dtsi b/arch/arm/dts/rk3566-anbernic-rgxx3-u-boot.dtsi new file mode 100644 index 0000000000..a18e5d1cf7 --- /dev/null +++ b/arch/arm/dts/rk3566-anbernic-rgxx3-u-boot.dtsi @@ -0,0 +1,86 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include "rk356x-u-boot.dtsi" + +/ { + chosen { + stdout-path = &uart2; + u-boot,spl-boot-order = "same-as-spl", &sdmmc1, &sdmmc0; + }; + + rng: rng@fe388000 { + compatible = "rockchip,cryptov2-rng"; + reg = <0x0 0xfe388000 0x0 0x2000>; + status = "okay"; + }; +}; + +&cru { + assigned-clocks = + <&pmucru CLK_RTC_32K>, + <&pmucru PLL_PPLL>, + <&pmucru PCLK_PMU>, <&cru PLL_CPLL>, + <&cru PLL_GPLL>, + <&cru ACLK_BUS>, <&cru PCLK_BUS>, + <&cru ACLK_TOP_HIGH>, <&cru ACLK_TOP_LOW>, + <&cru HCLK_TOP>, <&cru PCLK_TOP>, + <&cru ACLK_PERIMID>, <&cru HCLK_PERIMID>, + <&cru CPLL_500M>, <&cru CPLL_333M>, + <&cru CPLL_250M>, <&cru CPLL_125M>, + <&cru CPLL_100M>, <&cru CPLL_62P5M>, + <&cru CPLL_50M>, <&cru CPLL_25M>; + assigned-clock-rates = + <32768>, + <200000000>, + <100000000>, <1000000000>, + <1188000000>, + <150000000>, <100000000>, + <500000000>, <400000000>, + <150000000>, <100000000>, + <300000000>, <150000000>, + <500000000>, <333333333>, + <250000000>, <125000000>, + <100000000>, <62500000>, + <50000000>, <25000000>; + assigned-clock-parents = + <&pmucru CLK_RTC32K_FRAC>; +}; + +&i2c2 { + status = "okay"; +}; + +&pmucru { + assigned-clocks = <&pmucru SCLK_32K_IOE>; + assigned-clock-parents = <&pmucru CLK_RTC_32K>; +}; + +/* + * We don't need the clocks, but if they are present they may cause + * probing to fail so we remove them for U-Boot. + */ +&rk817 { + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ clocks; + /delete-property/ clock-names; +}; + +&sdhci { + pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, + <&emmc_datastrobe>, <&emmc_rstnout>; + pinctrl-names = "default"; + bus-width = <8>; + max-frequency = <200000000>; + mmc-hs200-1_8v; + non-removable; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&uart2 { + clock-frequency = <24000000>; + bootph-all; + status = "okay"; +}; diff --git a/arch/arm/dts/rk3566-anbernic-rgxx3.dts b/arch/arm/dts/rk3566-anbernic-rgxx3.dts new file mode 100644 index 0000000000..404dddfafb --- /dev/null +++ b/arch/arm/dts/rk3566-anbernic-rgxx3.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; + +#include "rk3566-anbernic-rgxx3.dtsi" + +/ { + +/* + * Note this is a pseudo-model that doesn't exist in mainline Linux. + * This model is used for all RGXX3 devices and the board.c file will + * set the correct dtb name for loading mainline Linux automatically. + */ + model = "RGXX3"; + compatible = "anbernic,rg353m", "anbernic,rg353p", + "anbernic,rg353v", "anbernic,rg353vs", + "anbernic,rg503", "rockchip,rk3566"; +}; diff --git a/arch/arm/dts/rk3566-anbernic-rgxx3.dtsi b/arch/arm/dts/rk3566-anbernic-rgxx3.dtsi new file mode 100644 index 0000000000..ad43fa199c --- /dev/null +++ b/arch/arm/dts/rk3566-anbernic-rgxx3.dtsi @@ -0,0 +1,786 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; + +#include +#include +#include +#include +#include +#include "rk3566.dtsi" + +/ { + chosen: chosen { + stdout-path = "serial2:1500000n8"; + }; + + adc-joystick { + compatible = "adc-joystick"; + io-channels = <&adc_mux 0>, + <&adc_mux 1>, + <&adc_mux 2>, + <&adc_mux 3>; + pinctrl-0 = <&joy_mux_en>; + pinctrl-names = "default"; + poll-interval = <60>; + #address-cells = <1>; + #size-cells = <0>; + + axis@0 { + reg = <0>; + abs-flat = <32>; + abs-fuzz = <32>; + abs-range = <1023 15>; + linux,code = ; + }; + + axis@1 { + reg = <1>; + abs-flat = <32>; + abs-fuzz = <32>; + abs-range = <15 1023>; + linux,code = ; + }; + + axis@2 { + reg = <2>; + abs-flat = <32>; + abs-fuzz = <32>; + abs-range = <15 1023>; + linux,code = ; + }; + + axis@3 { + reg = <3>; + abs-flat = <32>; + abs-fuzz = <32>; + abs-range = <1023 15>; + linux,code = ; + }; + }; + + adc_keys: adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1800000>; + poll-interval = <60>; + + /* + * Button is mapped to F key in BSP kernel, but + * according to input guidelines it should be mode. + */ + button-mode { + label = "MODE"; + linux,code = ; + press-threshold-microvolt = <1750>; + }; + }; + + adc_mux: adc-mux { + compatible = "io-channel-mux"; + channels = "left_x", "right_x", "left_y", "right_y"; + #io-channel-cells = <1>; + io-channels = <&saradc 3>; + io-channel-names = "parent"; + mux-controls = <&gpio_mux>; + settle-time-us = <100>; + }; + + gpio_keys_control: gpio-keys-control { + compatible = "gpio-keys"; + pinctrl-0 = <&btn_pins_ctrl>; + pinctrl-names = "default"; + + button-b { + gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>; + label = "SOUTH"; + linux,code = ; + }; + + button-down { + gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>; + label = "DPAD-DOWN"; + linux,code = ; + }; + + button-l1 { + gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>; + label = "TL"; + linux,code = ; + }; + + button-l2 { + gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>; + label = "TL2"; + linux,code = ; + }; + + button-select { + gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>; + label = "SELECT"; + linux,code = ; + }; + + button-start { + gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>; + label = "START"; + linux,code = ; + }; + + button-thumbl { + gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>; + label = "THUMBL"; + linux,code = ; + }; + + button-thumbr { + gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>; + label = "THUMBR"; + linux,code = ; + }; + + button-up { + gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>; + label = "DPAD-UP"; + linux,code = ; + }; + + button-x { + gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>; + label = "NORTH"; + linux,code = ; + }; + }; + + gpio_keys_vol: gpio-keys-vol { + compatible = "gpio-keys"; + autorepeat; + pinctrl-0 = <&btn_pins_vol>; + pinctrl-names = "default"; + + button-vol-down { + gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>; + label = "VOLUMEDOWN"; + linux,code = ; + }; + + button-vol-up { + gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>; + label = "VOLUMEUP"; + linux,code = ; + }; + }; + + gpio_mux: mux-controller { + compatible = "gpio-mux"; + mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>, + <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>; + #mux-control-cells = <0>; + }; + + hdmi-con { + compatible = "hdmi-connector"; + ddc-i2c-bus = <&i2c5>; + type = "c"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds: gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + green_led: led-0 { + color = ; + default-state = "on"; + function = LED_FUNCTION_POWER; + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>; + }; + + amber_led: led-1 { + color = ; + function = LED_FUNCTION_CHARGING; + gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; + retain-state-suspended; + }; + + red_led: led-2 { + color = ; + default-state = "off"; + function = LED_FUNCTION_STATUS; + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&rk817 1>; + clock-names = "ext_clock"; + pinctrl-0 = <&wifi_enable_h>; + pinctrl-names = "default"; + post-power-on-delay-ms = <200>; + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>; + }; + + vcc3v3_lcd0_n: regulator-vcc3v3-lcd0 { + compatible = "regulator-fixed"; + gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-0 = <&vcc_lcd_h>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3_lcd0_n"; + vin-supply = <&vcc_3v3>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_sys: regulator-vcc-sys { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3800000>; + regulator-max-microvolt = <3800000>; + regulator-name = "vcc_sys"; + }; + + vcc_wifi: regulator-vcc-wifi { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc_wifi_h>; + pinctrl-names = "default"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_wifi"; + }; + + vibrator: pwm-vibrator { + compatible = "pwm-vibrator"; + pwm-names = "enable"; + pwms = <&pwm5 0 1000000000 0>; + }; +}; + +&combphy1 { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&gpu { + mali-supply = <&vdd_gpu>; + status = "okay"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + pinctrl-0 = <&hdmitxm0_cec>; + pinctrl-names = "default"; + status = "okay"; +}; + +&hdmi_in { + hdmi_in_vp0: endpoint { + remote-endpoint = <&vp0_out_hdmi>; + }; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&hdmi_sound { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + rk817: pmic@20 { + compatible = "rockchip,rk817"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = ; + clock-output-names = "rk808-clkout1", "rk808-clkout2"; + clock-names = "mclk"; + clocks = <&cru I2S1_MCLKOUT_TX>; + assigned-clocks = <&cru I2S1_MCLKOUT_TX>; + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>; + #clock-cells = <1>; + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>; + wakeup-source; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_sys>; + vcc9-supply = <&dcdc_boost>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_logic"; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_3v3: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <0x2>; + regulator-name = "vcc_3v3"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca1v8_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca1v8_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda_0v9"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdda0v9_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_acodec"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3_pmu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_1v8: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_1v8"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc1v8_dvp: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc1v8_dvp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc2v8_dvp: LDO_REG9 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc2v8_dvp"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + dcdc_boost: BOOST { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <4700000>; + regulator-max-microvolt = <5400000>; + regulator-name = "boost"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + otg_switch: OTG_SWITCH { + regulator-name = "otg_switch"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; + + vdd_cpu: regulator@40 { + compatible = "fcs,fan53555"; + reg = <0x40>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1390000>; + regulator-init-microvolt = <900000>; + regulator-name = "vdd_cpu"; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc_sys>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c1 { + /* Unknown/unused device at 0x3c */ + status = "disabled"; +}; + +&i2c5 { + pinctrl-0 = <&i2c5m1_xfer>; + pinctrl-names = "default"; + status = "okay"; +}; + +&i2s0_8ch { + status = "okay"; +}; + +&i2s1_8ch { + pinctrl-0 = <&i2s1m0_sclktx + &i2s1m0_lrcktx + &i2s1m0_sdi0 + &i2s1m0_sdo0>; + pinctrl-names = "default"; + rockchip,trcm-sync-tx-only; + status = "okay"; +}; + +&pinctrl { + gpio-btns { + btn_pins_ctrl: btn-pins-ctrl { + rockchip,pins = + <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + btn_pins_vol: btn-pins-vol { + rockchip,pins = + <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>, + <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + gpio-led { + led_pins: led-pins { + rockchip,pins = + <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>, + <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>, + <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + joy-mux { + joy_mux_en: joy-mux-en { + rockchip,pins = + <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = + <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdio-pwrseq { + wifi_enable_h: wifi-enable-h { + rockchip,pins = + <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + vcc3v3-lcd { + vcc_lcd_h: vcc-lcd-h { + rockchip,pins = + <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + vcc-wifi { + vcc_wifi_h: vcc-wifi-h { + rockchip,pins = + <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&pmu_io_domains { + status = "okay"; + pmuio1-supply = <&vcc3v3_pmu>; + pmuio2-supply = <&vcc3v3_pmu>; + vccio1-supply = <&vccio_acodec>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_3v3>; + vccio6-supply = <&vcc1v8_dvp>; + vccio7-supply = <&vcc_3v3>; +}; + +&pwm5 { + status = "okay"; +}; + +&saradc { + vref-supply = <&vcc_1v8>; + status = "okay"; +}; + +&sdmmc0 { + bus-width = <4>; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; + disable-wp; + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; + pinctrl-names = "default"; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&sdmmc1 { + bus-width = <4>; + cap-sd-highspeed; + cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>; + disable-wp; + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>; + pinctrl-names = "default"; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc1v8_dvp>; + status = "okay"; +}; + +&sdmmc2 { + bus-width = <4>; + cap-sd-highspeed; + cap-sdio-irq; + keep-power-in-suspend; + mmc-pwrseq = <&sdio_pwrseq>; + non-removable; + pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>; + pinctrl-names = "default"; + vmmc-supply = <&vcc_wifi>; + vqmmc-supply = <&vcca1v8_pmu>; + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&uart1 { + pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>; + pinctrl-names = "default"; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8821cs-bt", "realtek,rtl8723bs-bt"; + device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; + enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart2 { + status = "okay"; +}; + +/* + * Lack the schematics to verify, but port works as a peripheral + * (and not a host or OTG port). + */ +&usb_host0_xhci { + dr_mode = "peripheral"; + phys = <&usb2phy0_otg>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +&usb_host1_xhci { + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb2phy1_host>, <&combphy1 PHY_TYPE_USB3>; + status = "okay"; +}; + +&usb2phy0 { + status = "okay"; +}; + +&usb2phy0_otg { + status = "okay"; +}; + +&usb2phy1 { + status = "okay"; +}; + +&usb2phy1_host { + status = "okay"; +}; + +&vop { + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; + status = "okay"; +}; + +&vop_mmu { + status = "okay"; +}; + +&vp0 { + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { + reg = ; + remote-endpoint = <&hdmi_in_vp0>; + }; +}; diff --git a/arch/arm/mach-rockchip/rk3568/Kconfig b/arch/arm/mach-rockchip/rk3568/Kconfig index 4e7c02cce0..94e04b79e7 100644 --- a/arch/arm/mach-rockchip/rk3568/Kconfig +++ b/arch/arm/mach-rockchip/rk3568/Kconfig @@ -1,11 +1,24 @@ if ROCKCHIP_RK3568 +choice + prompt "RK3568/RK3566 board select" + config TARGET_EVB_RK3568 bool "RK3568 evaluation board" select BOARD_LATE_INIT help RK3568 EVB is a evaluation board for Rockchp RK3568. +config TARGET_ANBERNIC_RGXX3_RK3566 + bool "Anbernic RGXX3" + help + Anbernic RGXX3 gaming device with Rockchip RK3566. This + config can be used with the RG353M, RG353P, RG353V, RG353VS, + and RG503. The correct device tree name will automatically + be selected by the bootloader. + +endchoice + config ROCKCHIP_BOOT_MODE_REG default 0xfdc20200 @@ -19,5 +32,6 @@ config SYS_MALLOC_F_LEN default 0x2000 source "board/rockchip/evb_rk3568/Kconfig" +source "board/anbernic/rgxx3_rk3566/Kconfig" endif diff --git a/board/anbernic/rgxx3_rk3566/Kconfig b/board/anbernic/rgxx3_rk3566/Kconfig new file mode 100644 index 0000000000..6743a28a2f --- /dev/null +++ b/board/anbernic/rgxx3_rk3566/Kconfig @@ -0,0 +1,15 @@ +if TARGET_ANBERNIC_RGXX3_RK3566 + +config SYS_BOARD + default "rgxx3_rk3566" + +config SYS_VENDOR + default "anbernic" + +config SYS_CONFIG_NAME + default "anbernic-rgxx3-rk3566" + +config BOARD_SPECIFIC_OPTIONS + def_bool y + +endif diff --git a/board/anbernic/rgxx3_rk3566/MAINTAINERS b/board/anbernic/rgxx3_rk3566/MAINTAINERS new file mode 100644 index 0000000000..647e49d28a --- /dev/null +++ b/board/anbernic/rgxx3_rk3566/MAINTAINERS @@ -0,0 +1,6 @@ +RGXX3-RK3566 +M: Chris Morgan +S: Maintained +F: board/anbernic/rgxx3-rk3566 +F: include/configs/anbernic-rgxx3-rk3566 +F: configs/anbernic-rgxx3_defconfig diff --git a/board/anbernic/rgxx3_rk3566/Makefile b/board/anbernic/rgxx3_rk3566/Makefile new file mode 100644 index 0000000000..afd3e0adf6 --- /dev/null +++ b/board/anbernic/rgxx3_rk3566/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023 Chris Morgan +# + +obj-y += rgxx3-rk3566.o diff --git a/board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c b/board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c new file mode 100644 index 0000000000..decc46db78 --- /dev/null +++ b/board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c @@ -0,0 +1,203 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (c) 2023 Chris Morgan + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define GPIO0_BASE 0xfdd60000 +#define GPIO_SWPORT_DR_H 0x0004 +#define GPIO_SWPORT_DDR_H 0x000c +#define GPIO_A5 BIT(5) +#define GPIO_A6 BIT(6) + +#define GPIO_WRITEMASK(bits) ((bits) << 16) + +#define DTB_DIR "rockchip/" + +struct rg3xx_model { + const char *board; + const char *board_name; + const char *fdtfile; +}; + +enum rgxx3_device_id { + RG353M, + RG353P, + RG353V, + RG353VS, + RG503, +}; + +static const struct rg3xx_model rg3xx_model_details[] = { + [RG353M] = { + "rk3566-anbernic-rg353m", + "RG353M", + DTB_DIR "rk3566-anbernic-rg353m.dtb", + }, + [RG353P] = { + "rk3566-anbernic-rg353p", + "RG353P", + DTB_DIR "rk3566-anbernic-rg353p.dtb", + }, + [RG353V] = { + "rk3566-anbernic-rg353v", + "RG353V", + DTB_DIR "rk3566-anbernic-rg353v.dtb", + }, + [RG353VS] = { + "rk3566-anbernic-rg353vs", + "RG353VS", + DTB_DIR "rk3566-anbernic-rg353vs.dtb", + }, + [RG503] = { + "rk3566-anbernic-rg503", + "RG503", + DTB_DIR "rk3566-anbernic-rg503.dtb", + }, +}; + +/* + * Start LED very early so user knows device is on. Set color + * to amber. + */ +void spl_board_init(void) +{ + /* Set GPIO0_A5 and GPIO0_A6 to output. */ + writel(GPIO_WRITEMASK(GPIO_A6 | GPIO_A5) | (GPIO_A6 | GPIO_A5), + (GPIO0_BASE + GPIO_SWPORT_DDR_H)); + /* Set GPIO0_A5 to 0 and GPIO0_A6 to 1. */ + writel(GPIO_WRITEMASK(GPIO_A6 | GPIO_A5) | GPIO_A6, + (GPIO0_BASE + GPIO_SWPORT_DR_H)); +} + +/* Use hardware rng to seed Linux random. */ +int board_rng_seed(struct abuf *buf) +{ + struct udevice *dev; + size_t len = 0x8; + u64 *data; + + data = malloc(len); + if (!data) { + printf("Out of memory\n"); + return -ENOMEM; + } + + if (uclass_get_device(UCLASS_RNG, 0, &dev) || !dev) { + printf("No RNG device\n"); + return -ENODEV; + } + + if (dm_rng_read(dev, data, len)) { + printf("Reading RNG failed\n"); + return -EIO; + } + + abuf_init_set(buf, data, len); + + return 0; +} + +/* + * Buzz the buzzer so the user knows something is going on. Make it + * optional in case PWM is disabled. + */ +void __maybe_unused startup_buzz(void) +{ + struct udevice *dev; + int err; + + err = uclass_get_device(UCLASS_PWM, 0, &dev); + if (err) + printf("pwm not found\n"); + + pwm_set_enable(dev, 0, 1); + mdelay(200); + pwm_set_enable(dev, 0, 0); +} + +/* Detect which Anbernic RGXX3 device we are using so as to load the + * correct devicetree for Linux. Set an environment variable once + * found. The detection depends on the value of ADC channel 1, the + * presence of an eMMC on mmc0, and querying the DSI panel (TODO). + */ +int rgxx3_detect_device(void) +{ + u32 adc_info; + int ret; + int board_id = -ENXIO; + struct mmc *mmc; + + ret = adc_channel_single_shot("saradc@fe720000", 1, &adc_info); + if (ret) { + printf("Read SARADC failed with error %d\n", ret); + return ret; + } + + /* Observed value 517. */ + if (adc_info > 505 && adc_info < 530) + board_id = RG353M; + /* Observed value 695. */ + if (adc_info > 680 && adc_info < 710) + board_id = RG353V; + /* Documented value 860. */ + if (adc_info > 850 && adc_info < 870) + board_id = RG353P; + /* Observed value 1023. */ + if (adc_info > 1010) + board_id = RG503; + + /* + * Try to access the eMMC on an RG353V. If it's missing, it's + * an RG353VS. Note we could also check for a touchscreen at + * 0x1a on i2c2. + */ + if (board_id == RG353V) { + mmc = find_mmc_device(0); + if (mmc) { + ret = mmc_init(mmc); + if (ret) + board_id = RG353VS; + } + } + + if (board_id < 0) + return board_id; + + env_set("board", rg3xx_model_details[board_id].board); + env_set("board_name", + rg3xx_model_details[board_id].board_name); + env_set("fdtfile", rg3xx_model_details[board_id].fdtfile); + + return 0; +} + +int rk_board_late_init(void) +{ + int ret; + + /* Turn off orange LED and turn on green LED. */ + writel(GPIO_WRITEMASK(GPIO_A6 | GPIO_A5) | GPIO_A5, + (GPIO0_BASE + GPIO_SWPORT_DR_H)); + + ret = rgxx3_detect_device(); + if (ret) { + printf("Unable to detect device type: %d\n", ret); + return ret; + } + + if (IS_ENABLED(CONFIG_DM_PWM)) + startup_buzz(); + + return 0; +} diff --git a/configs/anbernic-rgxx3_defconfig b/configs/anbernic-rgxx3_defconfig new file mode 100644 index 0000000000..b17e917914 --- /dev/null +++ b/configs/anbernic-rgxx3_defconfig @@ -0,0 +1,78 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_DEFAULT_DEVICE_TREE="rk3566-anbernic-rgxx3" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_BACK_TO_BROM=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_SPL_MMC=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_TARGET_ANBERNIC_RGXX3_RK3566=y +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-anbernic-rgxx3.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x20000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +CONFIG_SPL_BOARD_INIT=y +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_ATF=y +CONFIG_CMD_PWM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +# CONFIG_CMD_SETEXPR is not set +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +# CONFIG_NET is not set +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ARM_SMCCC_FEATURES=y +CONFIG_SCMI_FIRMWARE=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_FAN53555=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_PWM=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_DM_REGULATOR_SCMI=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_SYSRESET=y +CONFIG_REGEX=y +CONFIG_ERRNO_STR=y +# CONFIG_EFI_LOADER is not set diff --git a/doc/board/anbernic/index.rst b/doc/board/anbernic/index.rst new file mode 100644 index 0000000000..03758d8613 --- /dev/null +++ b/doc/board/anbernic/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Anbernic +======== + +.. toctree:: + :maxdepth: 2 + + rgxx3.rst diff --git a/doc/board/anbernic/rgxx3.rst b/doc/board/anbernic/rgxx3.rst new file mode 100644 index 0000000000..afa7538282 --- /dev/null +++ b/doc/board/anbernic/rgxx3.rst @@ -0,0 +1,47 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for Anbernic RGxx3 Devices +================================= + +This allows U-Boot to boot the following Anbernic devices: + + - Anbernic RG353M + - Anbernic RG353P + - Anbernic RG353V + - Anbernic RG353VS + - Anbernic RG503 + +The correct device is detected automatically by comparing ADC values +from ADC channel 1. In the event of an RG353V, an attempt is then made +to probe for an eMMC and if it fails the device is assumed to be an +RG353VS. Based on the detected device, the environment variables +"board", "board_name", and "fdtfile" are set to the correct values +corresponding to the board which can be read by a boot script to boot +with the correct device tree. + +Please note that there are some versions of the RG353 devices with +different panels. Panel auto-detection is planned for a later date. + +Building U-Boot +--------------- + +.. code-block:: bash + + $ export CROSS_COMPILE=aarch64-none-elf- + $ export BL31=../rkbin/bin/rk35/rk3568_bl31_v1.34.elf + $ export ROCKCHIP_TPL=../rkbin/bin/rk35/rk3568_ddr_1056MHz_v1.13.bin + $ make anbernic-rgxx3_defconfig + $ make + +This will build ``u-boot-rockchip.bin`` which can be written to an SD +card. + +Image installation +------------------ + +Write the ``u-boot-rockchip.bin`` to an SD card offset 32kb from the +start. + +.. code-block:: bash + + $ dd if=u-boot-rockchip.bin of=/dev/mmcblk0 bs=512 seek=64 diff --git a/doc/board/index.rst b/doc/board/index.rst index b2da6ec553..120daa48ee 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -11,6 +11,7 @@ Board-specific doc AndesTech/index allwinner/index amlogic/index + anbernic/index apple/index armltd/index atmel/index diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index 1dccb17d72..a21399c88e 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -87,6 +87,9 @@ List of mainline supported Rockchip boards: - Rockchip Evb-RK3399 (evb_rk3399) - Theobroma Systems RK3399-Q7 SoM - Puma (puma_rk3399) +* rk3566 + - Anbernic RGxx3 (rgxx3-rk3566) + * rk3568 - Rockchip Evb-RK3568 (evb-rk3568) diff --git a/include/configs/anbernic-rgxx3-rk3566.h b/include/configs/anbernic-rgxx3-rk3566.h new file mode 100644 index 0000000000..3c4ea4e7d8 --- /dev/null +++ b/include/configs/anbernic-rgxx3-rk3566.h @@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef __ANBERNIC_RGXX3_RK3566_H +#define __ANBERNIC_RGXX3_RK3566_H + +#include + +#define ROCKCHIP_DEVICE_SETTINGS \ + "stdout=serial,vidconsole\0" \ + "stderr=serial,vidconsole\0" + +#endif