This commit brings the omap3evm inline with the remaining OMAP3XXX variants.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
dtb-$(CONFIG_TARGET_USB_A9263) += usb_a9263.dtb
-dtb-$(CONFIG_TARGET_OMAP3_EVM) += \
- omap3-evm-37xx.dtb \
- omap3-evm.dtb
-
dtb-$(CONFIG_TARGET_DEVKIT8000) += omap3-devkit8000.dtb
dtb-$(CONFIG_TARGET_SAMA7G5EK) += \
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- */
-/dts-v1/;
-
-#include "omap36xx.dtsi"
-#include "omap3-evm-common.dtsi"
-#include "omap3-evm-processor-common.dtsi"
-
-/ {
- model = "TI OMAP37XX EVM (TMDSEVM3730)";
- compatible = "ti,omap3-evm-37xx", "ti,omap3630", "ti,omap3";
-};
-
-&omap3_pmx_core2 {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_2_pins>;
-
- ehci_phy_pins: pinmux_ehci_phy_pins {
- pinctrl-single,pins = <
-
- /* EHCI PHY reset GPIO etk_d7.gpio_21 */
- OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
-
- /* EHCI VBUS etk_d8.gpio_22 */
- OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_2_pins: pinmux_hsusb2_2_pins {
- pinctrl-single,pins = <
-
- /* etk_d10.hsusb2_clk */
- OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
-
- /* etk_d11.hsusb2_stp */
- OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
-
- /* etk_d12.hsusb2_dir */
- OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d13.hsusb2_nxt */
- OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d14.hsusb2_data0 */
- OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d15.hsusb2_data1 */
- OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-};
-
-&gpmc {
- nand@0,0 {
- compatible = "ti,omap2-nand";
- reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
- interrupt-parent = <&gpmc>;
- interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
- <1 IRQ_TYPE_NONE>; /* termcount */
- linux,mtd-name = "hynix,h8kds0un0mer-4em";
- nand-bus-width = <16>;
- gpmc,device-width = <2>;
- ti,nand-ecc-opt = "bch8";
-
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <44>;
- gpmc,cs-wr-off-ns = <44>;
- gpmc,adv-on-ns = <6>;
- gpmc,adv-rd-off-ns = <34>;
- gpmc,adv-wr-off-ns = <44>;
- gpmc,we-off-ns = <40>;
- gpmc,oe-off-ns = <54>;
- gpmc,access-ns = <64>;
- gpmc,rd-cycle-ns = <82>;
- gpmc,wr-cycle-ns = <82>;
- gpmc,wr-access-ns = <40>;
- gpmc,wr-data-mux-bus-ns = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "X-Loader";
- reg = <0 0x80000>;
- };
- partition@80000 {
- label = "U-Boot";
- reg = <0x80000 0x1c0000>;
- };
- partition@1c0000 {
- label = "Environment";
- reg = <0x240000 0x40000>;
- };
- partition@280000 {
- label = "Kernel";
- reg = <0x280000 0x500000>;
- };
- partition@780000 {
- label = "Filesystem";
- reg = <0x780000 0x1f880000>;
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Common support for omap3 EVM boards
- */
-
-#include <dt-bindings/input/input.h>
-#include "omap-gpmc-smsc911x.dtsi"
-
-/ {
- cpus {
- cpu@0 {
- cpu0-supply = <&vcc>;
- };
- };
-
- /* HS USB Port 2 Power */
- hsusb2_power: hsusb2_power_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb2_vbus";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; /* gpio_22 */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
- /* HS USB Host PHY on PORT 2 */
- hsusb2_phy: hsusb2_phy {
- compatible = "usb-nop-xceiv";
- reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */
- vcc-supply = <&hsusb2_power>;
- #phy-cells = <0>;
- };
-
- leds {
- compatible = "gpio-leds";
- ledb {
- label = "omap3evm::ledb";
- gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
- linux,default-trigger = "default-on";
- };
- };
-
- wl12xx_vmmc: wl12xx_vmmc {
- compatible = "regulator-fixed";
- regulator-name = "vwl1271";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* gpio150 */
- startup-delay-us = <70000>;
- enable-active-high;
- vin-supply = <&vmmc2>;
- };
-};
-
-&i2c1 {
- clock-frequency = <2600000>;
-
- twl: twl@48 {
- reg = <0x48>;
- interrupts = <7>; /* SYS_NIRQ cascaded to intc */
- interrupt-parent = <&intc>;
- };
-};
-
-#include "twl4030.dtsi"
-#include "twl4030_omap3.dtsi"
-#include "omap3-panel-sharp-ls037v7dw01.dtsi"
-
-&backlight0 {
- gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;
-};
-
-&twl {
- twl_power: power {
- compatible = "ti,twl4030-power-omap3-evm", "ti,twl4030-power-idle";
- ti,use_poweroff;
- };
-};
-
-&i2c2 {
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- clock-frequency = <400000>;
-
- /*
- * TVP5146 Video decoder-in for analog input support.
- */
- tvp5146@5c {
- compatible = "ti,tvp5146m2";
- reg = <0x5c>;
- };
-};
-
-&lcd_3v3 {
- gpio = <&gpio5 25 GPIO_ACTIVE_LOW>; /* gpio153 */
-};
-
-&lcd0 {
- enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
- reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
- mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
- &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
- &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */
-};
-
-&mcspi1 {
- tsc2046@0 {
- interrupt-parent = <&gpio6>;
- interrupts = <15 0>; /* gpio175 */
- pendown-gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&mmc1 {
- interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
- vmmc-supply = <&vmmc1>;
- vqmmc-supply = <&vsim>;
- bus-width = <8>;
-};
-
-&mmc2 {
- interrupts-extended = <&intc 86 &omap3_pmx_core 0x12e>;
- vmmc-supply = <&wl12xx_vmmc>;
- non-removable;
- bus-width = <4>;
- cap-power-off-card;
-
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1271";
- reg = <2>;
- /* gpio_149 with uart1_rts pad as wakeirq */
- interrupts-extended = <&gpio5 21 IRQ_TYPE_EDGE_RISING>,
- <&omap3_pmx_core 0x14e>;
- interrupt-names = "irq", "wakeup";
- ref-clock-frequency = <38400000>;
- };
-};
-
-&twl_gpio {
- ti,use-leds;
-};
-
-&twl_keypad {
- linux,keymap = <
- MATRIX_KEY(2, 2, KEY_1)
- MATRIX_KEY(1, 1, KEY_2)
- MATRIX_KEY(0, 0, KEY_3)
- MATRIX_KEY(3, 2, KEY_4)
- MATRIX_KEY(2, 1, KEY_5)
- MATRIX_KEY(1, 0, KEY_6)
- MATRIX_KEY(1, 3, KEY_7)
- MATRIX_KEY(3, 1, KEY_8)
- MATRIX_KEY(2, 0, KEY_9)
- MATRIX_KEY(2, 3, KEY_KPASTERISK)
- MATRIX_KEY(0, 2, KEY_0)
- MATRIX_KEY(3, 0, KEY_KPDOT)
- /* s4 not wired */
- MATRIX_KEY(1, 2, KEY_BACKSPACE)
- MATRIX_KEY(0, 1, KEY_ENTER)
- >;
-};
-
-&usbhshost {
- port2-mode = "ehci-phy";
-};
-
-&usbhsehci {
- phys = <0 &hsusb2_phy>;
-};
-
-&usb_otg_hs {
- interface-type = <0>;
- usb-phy = <&usb2_phy>;
- phys = <&usb2_phy>;
- phy-names = "usb2-phy";
- mode = <3>;
- power = <50>;
-};
-
-&gpmc {
- ethernet@gpmc {
- interrupt-parent = <&gpio6>;
- interrupts = <16 8>;
- reg = <5 0 0xff>;
- };
-};
-
-&vaux2 {
- regulator-name = "usb_1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
-};
+++ /dev/null
-/*
- * Common support for omap3 EVM 35xx/37xx processor modules
- */
-
-/ {
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x10000000>; /* 256 MB */
- };
-
- wl12xx_vmmc: wl12xx_vmmc {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_gpio>;
- };
-};
-
-&dss {
- vdds_dsi-supply = <&vpll2>;
- vdda_video-supply = <&lcd_3v3>;
- pinctrl-names = "default";
- pinctrl-0 = <
- &dss_dpi_pins1
- &dss_dpi_pins2
- >;
-};
-
-&hsusb2_phy {
- pinctrl-names = "default";
- pinctrl-0 = <&ehci_phy_pins>;
-};
-
-&omap3_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
-
- dss_dpi_pins1: pinmux_dss_dpi_pins2 {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
- OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
- OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
- OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
-
- OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
- OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
- OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
- OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
- OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
- OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
- OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
- OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
- OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
- OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
- OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
-
- OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
- OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
- OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
- OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
- OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
- OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
- >;
- };
-
- mmc1_pins: pinmux_mmc1_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
- OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
- OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
- OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
- OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
- OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
- OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */
- OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */
- OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */
- OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */
- >;
- };
-
- /* NOTE: Clocked externally, needs INPUT also for sdmmc2_clk.sdmmc2_clk */
- mmc2_pins: pinmux_mmc2_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
- OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
- OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
- OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
- OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
- OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
- OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */
- OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */
- OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */
- OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
- >;
- };
-
- /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
- on_board_gpio_61: pinmux_ehci_port_select_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_pins: pinmux_hsusb2_pins {
- pinctrl-single,pins = <
-
- /* mcspi1_cs3.hsusb2_data2 */
- OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_clk.hsusb2_data7 */
- OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_simo.hsusb2_data4 */
- OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_somi.hsusb2_data5 */
- OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs0.hsusb2_data6 */
- OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* mcspi2_cs1.hsusb2_data3 */
- OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-
- /*
- * Note that gpio_150 pulled high with internal pull to prevent wlcore
- * reset on return from off mode in idle.
- */
- wl12xx_gpio: pinmux_wl12xx_gpio {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE7) /* uart1_cts.gpio_150 */
- OMAP3_CORE1_IOPAD(0x217e, PIN_INPUT | MUX_MODE4) /* uart1_rts.gpio_149 */
- >;
- };
-
- smsc911x_pins: pinmux_smsc911x_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
- >;
- };
-};
-
-&omap3_pmx_wkup {
- dss_dpi_pins2: pinmux_dss_dpi_pins1 {
- pinctrl-single,pins = <
- OMAP3_WKUP_IOPAD(0x2a0a, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
- OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
- OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
- OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
- OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
- OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
- >;
- };
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&uart1 {
- interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-&uart2 {
- interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
-};
-
-&uart3 {
- interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
-};
-
-/*
- * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
- * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
- */
-&gpio2 {
- en-usb2-port-hog {
- gpio-hog;
- gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
- output-low;
- line-name = "enable usb2 port";
- };
-};
-
-/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
-&twl_gpio {
- en_on_board_gpio_61 {
- gpio-hog;
- gpios = <2 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "en_hsusb2_clk";
- };
-};
-
-&gpmc {
- ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
- <5 0 0x2c000000 0x01000000>; /* CS5: 16MB for LAN9220 */
-
- ethernet@gpmc {
- pinctrl-names = "default";
- pinctrl-0 = <&smsc911x_pins>;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- */
-/dts-v1/;
-
-#include "omap34xx.dtsi"
-#include "omap3-evm-common.dtsi"
-#include "omap3-evm-processor-common.dtsi"
-
-/ {
- model = "TI OMAP35XX EVM (TMDSEVM3530)";
- compatible = "ti,omap3-evm", "ti,omap3430", "ti,omap3";
-};
-
-&omap3_pmx_core2 {
- pinctrl-names = "default";
- pinctrl-0 = <&hsusb2_2_pins>;
-
- ehci_phy_pins: pinmux_ehci_phy_pins {
- pinctrl-single,pins = <
-
- /* EHCI PHY reset GPIO etk_d7.gpio_21 */
- OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
-
- /* EHCI VBUS etk_d8.gpio_22 */
- OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
- >;
- };
-
- /* Used by OHCI and EHCI. OHCI won't work without external phy */
- hsusb2_2_pins: pinmux_hsusb2_2_pins {
- pinctrl-single,pins = <
-
- /* etk_d10.hsusb2_clk */
- OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
-
- /* etk_d11.hsusb2_stp */
- OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
-
- /* etk_d12.hsusb2_dir */
- OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d13.hsusb2_nxt */
- OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d14.hsusb2_data0 */
- OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
-
- /* etk_d15.hsusb2_data1 */
- OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
- >;
- };
-};
-
-&gpmc {
- nand@0,0 {
- compatible = "ti,omap2-nand";
- reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
- interrupt-parent = <&gpmc>;
- interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
- <1 IRQ_TYPE_NONE>; /* termcount */
- linux,mtd-name = "micron,mt29f2g16abdhc";
- nand-bus-width = <16>;
- gpmc,device-width = <2>;
- ti,nand-ecc-opt = "bch8";
-
- gpmc,sync-clk-ps = <0>;
- gpmc,cs-on-ns = <0>;
- gpmc,cs-rd-off-ns = <44>;
- gpmc,cs-wr-off-ns = <44>;
- gpmc,adv-on-ns = <6>;
- gpmc,adv-rd-off-ns = <34>;
- gpmc,adv-wr-off-ns = <44>;
- gpmc,we-off-ns = <40>;
- gpmc,oe-off-ns = <54>;
- gpmc,access-ns = <64>;
- gpmc,rd-cycle-ns = <82>;
- gpmc,wr-cycle-ns = <82>;
- gpmc,wr-access-ns = <40>;
- gpmc,wr-data-mux-bus-ns = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Common file for omap dpi panels with QVGA and reset pins
- *
- * Note that the board specifc DTS file needs to specify
- * at minimum the GPIO enable-gpios for display, and
- * gpios for gpio-backlight.
- */
-
-/ {
- aliases {
- display0 = &lcd0;
- };
-
- backlight0: backlight {
- compatible = "gpio-backlight";
- default-on;
- };
-
- /* 3.3V GPIO controlled regulator for LCD_ENVDD */
- lcd_3v3: regulator-lcd-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "lcd_3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- startup-delay-us = <70000>;
- };
-
- lcd0: display {
- compatible = "sharp,ls037v7dw01";
- label = "lcd";
- power-supply = <&lcd_3v3>;
- envdd-supply = <&lcd_3v3>;
-
- port {
- lcd_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
- };
-};
-
-/* Needed to power the DPI pins */
-&vpll2 {
- regulator-always-on;
-};
-
-&dss {
- status = "okay";
- port {
- dpi_out: endpoint {
- remote-endpoint = <&lcd_in>;
- data-lines = <18>;
- };
- };
-};
-
-&mcspi1 {
- tsc2046@0 {
- reg = <0>; /* CS0 */
- compatible = "ti,tsc2046";
- spi-max-frequency = <1000000>;
- vcc-supply = <&lcd_3v3>;
- ti,x-min = /bits/ 16 <0>;
- ti,x-max = /bits/ 16 <8000>;
- ti,y-min = /bits/ 16 <0>;
- ti,y-max = /bits/ 16 <4800>;
- ti,x-plate-ohms = /bits/ 16 <40>;
- ti,pressure-max = /bits/ 16 <255>;
- ti,swap-xy;
- wakeup-source;
- };
-};
# CONFIG_SPL_USE_ARCH_MEMSET is not set
CONFIG_ARCH_OMAP2PLUS=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
-CONFIG_DEFAULT_DEVICE_TREE="omap3-evm"
+CONFIG_DEFAULT_DEVICE_TREE="ti/omap/omap3-evm"
CONFIG_TARGET_OMAP3_EVM=y
CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
CONFIG_SPL=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(spl),1920k(u-boot),128k(u-boot-env),128k(dtb),6m(kernel),-(rootfs)"
CONFIG_CMD_UBI=y
# CONFIG_ISO_PARTITION is not set
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_SPL_PARTITION_UUIDS=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_UPSTREAM=y
CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FAT=y
projects / u-boot.git / commitdiff
