echo "#define CONFIG_NAND_U_BOOT" >> $(obj)include/config.h; \
else \
echo "#define CONFIG_SKIP_LOWLEVEL_INIT" >> $(obj)include/config.h; \
- echo "#define CONFIG_SKIP_RELOCATE_UBOOT" >> $(obj)include/config.h; \
fi
@$(MKCONFIG) -n $@ -a mx31pdk arm arm1136 mx31pdk freescale mx31
globally (CONFIG_CMD_MEM).
- CONFIG_SKIP_LOWLEVEL_INIT
-- CONFIG_SKIP_RELOCATE_UBOOT
+ [ARM only] If this variable is defined, then certain
+ low level initializations (like setting up the memory
+ controller) are omitted and/or U-Boot does not
+ relocate itself into RAM.
- [ARM only] If these variables are defined, then
- certain low level initializations (like setting up
- the memory controller) are omitted and/or U-Boot does
- not relocate itself into RAM.
- Normally these variables MUST NOT be defined. The
- only exception is when U-Boot is loaded (to RAM) by
- some other boot loader or by a debugger which
- performs these initializations itself.
+ Normally this variable MUST NOT be defined. The only
+ exception is when U-Boot is loaded (to RAM) by some
+ other boot loader or by a debugger which performs
+ these initializations itself.
- CONFIG_PRELOADER
-
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
ldr r0, _board_init_r_ofs
adr r1, _start
add lr, r0, r1
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
add lr, lr, r9
-#endif
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
#ifdef CONFIG_ENABLE_MMU
enable_mmu:
ldr r0, _board_init_r_ofs
adr r1, _start
add lr, r0, r1
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
add lr, lr, r9
-#endif
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
ldr r0, _board_init_r_ofs
adr r1, _start
add lr, r0, r1
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
add lr, lr, r9
-#endif
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
stack_setup:
mov sp, r4
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
adr r0, _start
ldr r2, _TEXT_BASE
ldr r3, _bss_start_ofs
cmp r0, r1
bne clbss_l
#endif /* #ifndef CONFIG_PRELOADER */
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
/*
* We are done. Do not return, instead branch to second part of board
ldr r0, _board_init_r_ofs
adr r1, _start
add lr, r0, r1
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
add lr, lr, r9
-#endif
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
stmfd sp!, {r0-r12}
copy_loop:
ldmia r0!, {r3-r5, r7-r11} /* copy from source address [r0] */
cmp r2, r3
blo fixloop
#endif /* #ifndef CONFIG_PRELOADER */
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
ldr r0, _board_init_r_ofs
adr r1, _start
add lr, r0, r1
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
add lr, lr, r9
-#endif
/* setup parameters for board_init_r */
mov r0, r5 /* gd_t */
mov r1, r7 /* dest_addr */
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
stmia r1!, {r3-r10}
cmp r0, r2
blo vector_copy_loop
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
cmp r0, r6
beq clear_bss
-#ifndef CONFIG_SKIP_RELOCATE_UBOOT
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r6!, {r9-r10} /* copy to target address [r1] */
cmp r2, r3
blo fixloop
#endif
-#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
clear_bss:
#ifndef CONFIG_PRELOADER
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* High Level Configuration Options
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
-#else
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
/*
* Size of malloc() pool
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#ifndef CONFIG_SYS_USE_BOOT_NORFLASH
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif
/*
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
-#else
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
/*
#define CONFIG_VPAC270 1 /* Toradex Colibri PXA270 board */
#undef BOARD_LATE_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#undef CONFIG_USE_IRQ
#undef CONFIG_SKIP_LOWLEVEL_INIT
#ifdef CONFIG_CPUAT91_RAM
#define CONFIG_SKIP_LOWLEVEL_INIT 1
-#define CONFIG_SKIP_RELOCATE_UBOOT 1
#else
#define CONFIG_BOOTDELAY 1
#endif
#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
-#else
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
/*
* Size of malloc() pool
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SYS_HZ 1000
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_TEXT_BASE 0xc1080000
/*
#define DAVINCI_DM355EVM
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
#define CONFIG_DISPLAY_CPUINFO
#define DAVINCI_DM355LEOPARD
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
#define CONFIG_DISPLAY_CPUINFO
#define DAVINCI_DM365EVM
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
#define DAVINCI_DM6467EVM
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/* SoC Configuration */
#define CONFIG_ARM926EJS /* arm926ejs CPU */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#endif
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_HW_ECC
#elif defined(CONFIG_SYS_USE_NOR)
#ifdef CONFIG_NOR_UART_BOOT
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#else
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#endif
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#elif defined(CONFIG_SYS_USE_NOR)
#ifdef CONFIG_NOR_UART_BOOT
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#else
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#endif
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_NO_FLASH
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#define CONFIG_SKIP_LOWLEVEL_INIT 1
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* High Level Configuration Options
* we use lowlevel_init (!CONFIG_SKIP_LOWLEVEL_INIT) to remedy that problem.
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT 1
/*
* High Level Configuration Options
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT /* undef this for direct boot from */
- /* NOR flash without preloader */
#define CONFIG_SYS_LONGHELP
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* High Level Configuration Options
#undef CONFIG_USE_IRQ /* don't need IRQ/FIQ stuff */
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_MISC_INIT_R /* Call misc_init_r */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
-#else
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
/*
#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
#endif
/*
/* High Level Configuration Options */
#define CONFIG_MX51 /* in a mx51 */
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_SYS_MX5_HCLK 24000000
#define CONFIG_SYS_MX5_CLK32 32768
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-/*#define CONFIG_SKIP_RELOCATE_UBOOT*/
-/*#define CONFIG_SKIP_LOWLEVEL_INIT */
-
/*
* Partitions (mtdparts command line support)
*/
#undef CONFIG_USE_IRQ /* don't need IRQ/FIQ stuff */
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_INITRD_TAG 1
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
#define CONFIG_INITRD_TAG 1
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_USER_LOWLEVEL_INIT 1
/*
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT /* define for developing */
-#undef CONFIG_SKIP_RELOCATE_UBOOT /* define for developing */
#define CONFIG_SYS_TEXT_BASE 0x0
/*
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
/* input clock of PLL: has 24MHz input clock at S5PC110 */
#define CONFIG_SYS_CLK_FREQ_C110 24000000
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
*/
#define CONFIG_INFERNO /* we are using the inferno bootldr */
#define CONFIG_SKIP_LOWLEVEL_INIT 1
-#undef CONFIG_SKIP_RELOCATE_UBOOT
/*
* High Level Configuration Options
#define CONFIG_S3C64XX 1 /* in a SAMSUNG S3C64XX Family */
#define CONFIG_SMDK6400 1 /* on a SAMSUNG SMDK6400 Board */
-#define CONFIG_SKIP_RELOCATE_UBOOT
-
#define CONFIG_PERIPORT_REMAP
#define CONFIG_PERIPORT_BASE 0x70000000
#define CONFIG_PERIPORT_SIZE 0x13
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
/* input clock of PLL: SMDKC100 has 12MHz input clock */
#define CONFIG_SYS_CLK_FREQ 12000000
#define CONFIG_INITRD_TAG 1
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
/*
* Hardware drivers
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_GBL_DATA_OFFSET)
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
#define CONFIG_BOARD_EARLY_INIT_F
/* 166 MHz DDR RAM */
#define CONFIG_SYS_TEXT_BASE 0x0
#undef BOARD_LATE_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#undef CONFIG_USE_IRQ
#undef CONFIG_SKIP_LOWLEVEL_INIT
#undef CONFIG_MMC
#define BOARD_LATE_INIT 1
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
/* we will never enable dcache, because we have to setup MMU first */
projects / u-boot.git / commitdiff
