bool "Renesas R2D-PLUS"
select CPU_SH4
-config TARGET_SH7752EVB
- bool "SH7752EVB"
- select CPU_SH4A
-
config TARGET_SH7753EVB
bool "SH7753EVB"
select CPU_SH4
source "arch/sh/lib/Kconfig"
source "board/renesas/r2dplus/Kconfig"
-source "board/renesas/sh7752evb/Kconfig"
source "board/renesas/sh7753evb/Kconfig"
source "board/renesas/sh7757lcr/Kconfig"
source "board/renesas/sh7763rdp/Kconfig"
+++ /dev/null
-if TARGET_SH7752EVB
-
-config SYS_BOARD
- default "sh7752evb"
-
-config SYS_VENDOR
- default "renesas"
-
-config SYS_CONFIG_NAME
- default "sh7752evb"
-
-endif
+++ /dev/null
-SH7752EVB BOARD
-#M: -
-S: Maintained
-F: board/renesas/sh7752evb/
-F: include/configs/sh7752evb.h
-F: configs/sh7752evb_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2012 Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
-#
-
-obj-y := sh7752evb.o spi-boot.o
-extra-y += lowlevel_init.o
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Renesas Solutions Corp.
- */
-
-#include <config.h>
-#include <asm/processor.h>
-#include <asm/macro.h>
-
-.macro or32, addr, data
- mov.l \addr, r1
- mov.l \data, r0
- mov.l @r1, r2
- or r2, r0
- mov.l r0, @r1
-.endm
-
-.macro wait_DBCMD
- mov.l DBWAIT_A, r0
- mov.l @r0, r1
-.endm
-
- .global lowlevel_init
- .section .spiboot1.text
- .align 2
-
-lowlevel_init:
- /*------- GPIO -------*/
- write16 PDCR_A, PDCR_D ! SPI0
- write16 PGCR_A, PGCR_D ! SPI0, GETHER MDIO gate(PTG1)
- write16 PJCR_A, PJCR_D ! SCIF4
- write16 PTCR_A, PTCR_D ! STATUS
- write16 PSEL1_A, PSEL1_D ! SPI0
- write16 PSEL2_A, PSEL2_D ! SPI0
- write16 PSEL5_A, PSEL5_D ! STATUS
-
- bra exit_gpio
- nop
-
- .align 2
-
-/*------- GPIO -------*/
-PDCR_A: .long 0xffec0006
-PGCR_A: .long 0xffec000c
-PJCR_A: .long 0xffec0012
-PTCR_A: .long 0xffec0026
-PSEL1_A: .long 0xffec0072
-PSEL2_A: .long 0xffec0074
-PSEL5_A: .long 0xffec007a
-
-PDCR_D: .long 0x0000
-PGCR_D: .long 0x0004
-PJCR_D: .long 0x0000
-PTCR_D: .long 0x0000
-PSEL1_D: .long 0x0000
-PSEL2_D: .long 0x3000
-PSEL5_D: .long 0x0ffc
-
- .align 2
-
-exit_gpio:
- mov #0, r14
- mova 2f, r0
- mov.l PC_MASK, r1
- tst r0, r1
- bf 2f
-
- bra exit_pmb
- nop
-
- .align 2
-
-/* If CPU runs on SDRAM (PC=0x5???????) or not. */
-PC_MASK: .long 0x20000000
-
-2:
- mov #1, r14
-
- mov.l EXPEVT_A, r0
- mov.l @r0, r0
- mov.l EXPEVT_POWER_ON_RESET, r1
- cmp/eq r0, r1
- bt 1f
-
- /*
- * If EXPEVT value is manual reset or tlb multipul-hit,
- * initialization of DDR3IF is not necessary.
- */
- bra exit_ddr
- nop
-
-1:
- /*------- Reset -------*/
- write32 MRSTCR0_A, MRSTCR0_D
- write32 MRSTCR1_A, MRSTCR1_D
-
- /* For Core Reset */
- mov.l DBACEN_A, r0
- mov.l @r0, r0
- cmp/eq #0, r0
- bt 3f
-
- /*
- * If DBACEN == 1(DBSC was already enabled), we have to avoid the
- * initialization of DDR3-SDRAM.
- */
- bra exit_ddr
- nop
-
-3:
- /*------- DDR3IF -------*/
- /* oscillation stabilization time */
- wait_timer WAIT_OSC_TIME
-
- /* step 3 */
- write32 DBCMD_A, DBCMD_RSTL_VAL
- wait_timer WAIT_30US
-
- /* step 4 */
- write32 DBCMD_A, DBCMD_PDEN_VAL
-
- /* step 5 */
- write32 DBKIND_A, DBKIND_D
-
- /* step 6 */
- write32 DBCONF_A, DBCONF_D
- write32 DBTR0_A, DBTR0_D
- write32 DBTR1_A, DBTR1_D
- write32 DBTR2_A, DBTR2_D
- write32 DBTR3_A, DBTR3_D
- write32 DBTR4_A, DBTR4_D
- write32 DBTR5_A, DBTR5_D
- write32 DBTR6_A, DBTR6_D
- write32 DBTR7_A, DBTR7_D
- write32 DBTR8_A, DBTR8_D
- write32 DBTR9_A, DBTR9_D
- write32 DBTR10_A, DBTR10_D
- write32 DBTR11_A, DBTR11_D
- write32 DBTR12_A, DBTR12_D
- write32 DBTR13_A, DBTR13_D
- write32 DBTR14_A, DBTR14_D
- write32 DBTR15_A, DBTR15_D
- write32 DBTR16_A, DBTR16_D
- write32 DBTR17_A, DBTR17_D
- write32 DBTR18_A, DBTR18_D
- write32 DBTR19_A, DBTR19_D
- write32 DBRNK0_A, DBRNK0_D
-
- /* step 7 */
- write32 DBPDCNT3_A, DBPDCNT3_D
-
- /* step 8 */
- write32 DBPDCNT1_A, DBPDCNT1_D
- write32 DBPDCNT2_A, DBPDCNT2_D
- write32 DBPDLCK_A, DBPDLCK_D
- write32 DBPDRGA_A, DBPDRGA_D
- write32 DBPDRGD_A, DBPDRGD_D
-
- /* step 9 */
- wait_timer WAIT_30US
-
- /* step 10 */
- write32 DBPDCNT0_A, DBPDCNT0_D
-
- /* step 11 */
- wait_timer WAIT_30US
- wait_timer WAIT_30US
-
- /* step 12 */
- write32 DBCMD_A, DBCMD_WAIT_VAL
- wait_DBCMD
-
- /* step 13 */
- write32 DBCMD_A, DBCMD_RSTH_VAL
- wait_DBCMD
-
- /* step 14 */
- write32 DBCMD_A, DBCMD_WAIT_VAL
- write32 DBCMD_A, DBCMD_WAIT_VAL
- write32 DBCMD_A, DBCMD_WAIT_VAL
- write32 DBCMD_A, DBCMD_WAIT_VAL
-
- /* step 15 */
- write32 DBCMD_A, DBCMD_PDXT_VAL
-
- /* step 16 */
- write32 DBCMD_A, DBCMD_MRS2_VAL
-
- /* step 17 */
- write32 DBCMD_A, DBCMD_MRS3_VAL
-
- /* step 18 */
- write32 DBCMD_A, DBCMD_MRS1_VAL
-
- /* step 19 */
- write32 DBCMD_A, DBCMD_MRS0_VAL
-
- /* step 20 */
- write32 DBCMD_A, DBCMD_ZQCL_VAL
-
- write32 DBCMD_A, DBCMD_REF_VAL
- write32 DBCMD_A, DBCMD_REF_VAL
- wait_DBCMD
-
- /* step 21 */
- write32 DBADJ0_A, DBADJ0_D
- write32 DBADJ1_A, DBADJ1_D
- write32 DBADJ2_A, DBADJ2_D
-
- /* step 22 */
- write32 DBRFCNF0_A, DBRFCNF0_D
- write32 DBRFCNF1_A, DBRFCNF1_D
- write32 DBRFCNF2_A, DBRFCNF2_D
-
- /* step 23 */
- write32 DBCALCNF_A, DBCALCNF_D
-
- /* step 24 */
- write32 DBRFEN_A, DBRFEN_D
- write32 DBCMD_A, DBCMD_SRXT_VAL
-
- /* step 25 */
- write32 DBACEN_A, DBACEN_D
-
- /* step 26 */
- wait_DBCMD
-
- bra exit_ddr
- nop
-
- .align 2
-
-EXPEVT_A: .long 0xff000024
-EXPEVT_POWER_ON_RESET: .long 0x00000000
-
-/*------- Reset -------*/
-MRSTCR0_A: .long 0xffd50030
-MRSTCR0_D: .long 0xfe1ffe7f
-MRSTCR1_A: .long 0xffd50034
-MRSTCR1_D: .long 0xfff3ffff
-
-/*------- DDR3IF -------*/
-DBCMD_A: .long 0xfe800018
-DBKIND_A: .long 0xfe800020
-DBCONF_A: .long 0xfe800024
-DBTR0_A: .long 0xfe800040
-DBTR1_A: .long 0xfe800044
-DBTR2_A: .long 0xfe800048
-DBTR3_A: .long 0xfe800050
-DBTR4_A: .long 0xfe800054
-DBTR5_A: .long 0xfe800058
-DBTR6_A: .long 0xfe80005c
-DBTR7_A: .long 0xfe800060
-DBTR8_A: .long 0xfe800064
-DBTR9_A: .long 0xfe800068
-DBTR10_A: .long 0xfe80006c
-DBTR11_A: .long 0xfe800070
-DBTR12_A: .long 0xfe800074
-DBTR13_A: .long 0xfe800078
-DBTR14_A: .long 0xfe80007c
-DBTR15_A: .long 0xfe800080
-DBTR16_A: .long 0xfe800084
-DBTR17_A: .long 0xfe800088
-DBTR18_A: .long 0xfe80008c
-DBTR19_A: .long 0xfe800090
-DBRNK0_A: .long 0xfe800100
-DBPDCNT0_A: .long 0xfe800200
-DBPDCNT1_A: .long 0xfe800204
-DBPDCNT2_A: .long 0xfe800208
-DBPDCNT3_A: .long 0xfe80020c
-DBPDLCK_A: .long 0xfe800280
-DBPDRGA_A: .long 0xfe800290
-DBPDRGD_A: .long 0xfe8002a0
-DBADJ0_A: .long 0xfe8000c0
-DBADJ1_A: .long 0xfe8000c4
-DBADJ2_A: .long 0xfe8000c8
-DBRFCNF0_A: .long 0xfe8000e0
-DBRFCNF1_A: .long 0xfe8000e4
-DBRFCNF2_A: .long 0xfe8000e8
-DBCALCNF_A: .long 0xfe8000f4
-DBRFEN_A: .long 0xfe800014
-DBACEN_A: .long 0xfe800010
-DBWAIT_A: .long 0xfe80001c
-
-WAIT_OSC_TIME: .long 6000
-WAIT_30US: .long 13333
-
-DBCMD_RSTL_VAL: .long 0x20000000
-DBCMD_PDEN_VAL: .long 0x1000d73c
-DBCMD_WAIT_VAL: .long 0x0000d73c
-DBCMD_RSTH_VAL: .long 0x2100d73c
-DBCMD_PDXT_VAL: .long 0x110000c8
-DBCMD_MRS0_VAL: .long 0x28000930
-DBCMD_MRS1_VAL: .long 0x29000004
-DBCMD_MRS2_VAL: .long 0x2a000008
-DBCMD_MRS3_VAL: .long 0x2b000000
-DBCMD_ZQCL_VAL: .long 0x03000200
-DBCMD_REF_VAL: .long 0x0c000000
-DBCMD_SRXT_VAL: .long 0x19000000
-DBKIND_D: .long 0x00000007
-DBCONF_D: .long 0x0f030a01
-DBTR0_D: .long 0x00000007
-DBTR1_D: .long 0x00000006
-DBTR2_D: .long 0x00000000
-DBTR3_D: .long 0x00000007
-DBTR4_D: .long 0x00070007
-DBTR5_D: .long 0x0000001b
-DBTR6_D: .long 0x00000014
-DBTR7_D: .long 0x00000005
-DBTR8_D: .long 0x00000015
-DBTR9_D: .long 0x00000006
-DBTR10_D: .long 0x00000008
-DBTR11_D: .long 0x00000007
-DBTR12_D: .long 0x0000000e
-DBTR13_D: .long 0x00000056
-DBTR14_D: .long 0x00000006
-DBTR15_D: .long 0x00000004
-DBTR16_D: .long 0x00150002
-DBTR17_D: .long 0x000c0017
-DBTR18_D: .long 0x00000200
-DBTR19_D: .long 0x00000040
-DBRNK0_D: .long 0x00000001
-DBPDCNT0_D: .long 0x00000001
-DBPDCNT1_D: .long 0x00000001
-DBPDCNT2_D: .long 0x00000000
-DBPDCNT3_D: .long 0x00004010
-DBPDLCK_D: .long 0x0000a55a
-DBPDRGA_D: .long 0x00000028
-DBPDRGD_D: .long 0x00017100
-
-DBADJ0_D: .long 0x00000000
-DBADJ1_D: .long 0x00000000
-DBADJ2_D: .long 0x18061806
-DBRFCNF0_D: .long 0x000001ff
-DBRFCNF1_D: .long 0x08001000
-DBRFCNF2_D: .long 0x00000000
-DBCALCNF_D: .long 0x0000ffff
-DBRFEN_D: .long 0x00000001
-DBACEN_D: .long 0x00000001
-
- .align 2
-exit_ddr:
-#if defined(CONFIG_SH_32BIT)
- /*------- set PMB -------*/
- write32 PASCR_A, PASCR_29BIT_D
- write32 MMUCR_A, MMUCR_D
-
- /*****************************************************************
- * ent virt phys v sz c wt
- * 0 0xa0000000 0x00000000 1 128M 0 1
- * 1 0xa8000000 0x48000000 1 128M 0 1
- * 5 0x88000000 0x48000000 1 128M 1 1
- */
- write32 PMB_ADDR_SPIBOOT_A, PMB_ADDR_SPIBOOT_D
- write32 PMB_DATA_SPIBOOT_A, PMB_DATA_SPIBOOT_D
- write32 PMB_ADDR_DDR_C1_A, PMB_ADDR_DDR_C1_D
- write32 PMB_DATA_DDR_C1_A, PMB_DATA_DDR_C1_D
- write32 PMB_ADDR_DDR_N1_A, PMB_ADDR_DDR_N1_D
- write32 PMB_DATA_DDR_N1_A, PMB_DATA_DDR_N1_D
-
- write32 PMB_ADDR_ENTRY2, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY3, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY4, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY6, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY7, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY8, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY9, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY10, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY11, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY12, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY13, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY14, PMB_ADDR_NOT_USE_D
- write32 PMB_ADDR_ENTRY15, PMB_ADDR_NOT_USE_D
-
- write32 PASCR_A, PASCR_INIT
- mov.l DUMMY_ADDR, r0
- icbi @r0
-#endif /* if defined(CONFIG_SH_32BIT) */
-
-exit_pmb:
- /* CPU is running on ILRAM? */
- mov r14, r0
- tst #1, r0
- bt 1f
-
- mov.l _stack_ilram, r15
- mov.l _spiboot_main, r0
-100: bsrf r0
- nop
-
- .align 2
-_spiboot_main: .long (spiboot_main - (100b + 4))
-_stack_ilram: .long 0xe5204000
-
-1:
- write32 CCR_A, CCR_D
-
- rts
- nop
-
- .align 2
-
-#if defined(CONFIG_SH_32BIT)
-/*------- set PMB -------*/
-PMB_ADDR_SPIBOOT_A: .long PMB_ADDR_BASE(0)
-PMB_ADDR_DDR_N1_A: .long PMB_ADDR_BASE(1)
-PMB_ADDR_DDR_C1_A: .long PMB_ADDR_BASE(5)
-PMB_ADDR_ENTRY2: .long PMB_ADDR_BASE(2)
-PMB_ADDR_ENTRY3: .long PMB_ADDR_BASE(3)
-PMB_ADDR_ENTRY4: .long PMB_ADDR_BASE(4)
-PMB_ADDR_ENTRY6: .long PMB_ADDR_BASE(6)
-PMB_ADDR_ENTRY7: .long PMB_ADDR_BASE(7)
-PMB_ADDR_ENTRY8: .long PMB_ADDR_BASE(8)
-PMB_ADDR_ENTRY9: .long PMB_ADDR_BASE(9)
-PMB_ADDR_ENTRY10: .long PMB_ADDR_BASE(10)
-PMB_ADDR_ENTRY11: .long PMB_ADDR_BASE(11)
-PMB_ADDR_ENTRY12: .long PMB_ADDR_BASE(12)
-PMB_ADDR_ENTRY13: .long PMB_ADDR_BASE(13)
-PMB_ADDR_ENTRY14: .long PMB_ADDR_BASE(14)
-PMB_ADDR_ENTRY15: .long PMB_ADDR_BASE(15)
-
-PMB_ADDR_SPIBOOT_D: .long mk_pmb_addr_val(0xa0)
-PMB_ADDR_DDR_C1_D: .long mk_pmb_addr_val(0x88)
-PMB_ADDR_DDR_N1_D: .long mk_pmb_addr_val(0xa8)
-PMB_ADDR_NOT_USE_D: .long 0x00000000
-
-PMB_DATA_SPIBOOT_A: .long PMB_DATA_BASE(0)
-PMB_DATA_DDR_N1_A: .long PMB_DATA_BASE(1)
-PMB_DATA_DDR_C1_A: .long PMB_DATA_BASE(5)
-
-/* ppn ub v s1 s0 c wt */
-PMB_DATA_SPIBOOT_D: .long mk_pmb_data_val(0x00, 0, 1, 1, 0, 0, 1)
-PMB_DATA_DDR_C1_D: .long mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1)
-PMB_DATA_DDR_N1_D: .long mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1)
-
-PASCR_A: .long 0xff000070
-DUMMY_ADDR: .long 0xa0000000
-PASCR_29BIT_D: .long 0x00000000
-PASCR_INIT: .long 0x80000080
-MMUCR_A: .long 0xff000010
-MMUCR_D: .long 0x00000004 /* clear ITLB */
-#endif /* CONFIG_SH_32BIT */
-
-CCR_A: .long CCR
-CCR_D: .long CCR_CACHE_INIT
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Renesas Solutions Corp.
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <flash.h>
-#include <init.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/mmc.h>
-#include <spi.h>
-#include <spi_flash.h>
-#include <linux/delay.h>
-
-int checkboard(void)
-{
- puts("BOARD: SH7752 evaluation board (R0P7752C00000RZ)\n");
-
- return 0;
-}
-
-static void init_gpio(void)
-{
- struct gpio_regs *gpio = GPIO_BASE;
- struct sermux_regs *sermux = SERMUX_BASE;
-
- /* GPIO */
- writew(0x0000, &gpio->pacr); /* GETHER */
- writew(0x0001, &gpio->pbcr); /* INTC */
- writew(0x0000, &gpio->pccr); /* PWMU, INTC */
- writew(0xeaff, &gpio->pecr); /* GPIO */
- writew(0x0000, &gpio->pfcr); /* WDT */
- writew(0x0000, &gpio->phcr); /* SPI1 */
- writew(0x0000, &gpio->picr); /* SDHI */
- writew(0x0003, &gpio->pkcr); /* SerMux */
- writew(0x0000, &gpio->plcr); /* SerMux */
- writew(0x0000, &gpio->pmcr); /* RIIC */
- writew(0x0000, &gpio->pncr); /* USB, SGPIO */
- writew(0x0000, &gpio->pocr); /* SGPIO */
- writew(0xd555, &gpio->pqcr); /* GPIO */
- writew(0x0000, &gpio->prcr); /* RIIC */
- writew(0x0000, &gpio->pscr); /* RIIC */
- writeb(0x00, &gpio->pudr);
- writew(0x5555, &gpio->pucr); /* Debug LED */
- writew(0x0000, &gpio->pvcr); /* RSPI */
- writew(0x0000, &gpio->pwcr); /* EVC */
- writew(0x0000, &gpio->pxcr); /* LBSC */
- writew(0x0000, &gpio->pycr); /* LBSC */
- writew(0x0000, &gpio->pzcr); /* eMMC */
- writew(0xfe00, &gpio->psel0);
- writew(0xff00, &gpio->psel3);
- writew(0x771f, &gpio->psel4);
- writew(0x00ff, &gpio->psel6);
- writew(0xfc00, &gpio->psel7);
-
- writeb(0x10, &sermux->smr0); /* SMR0: SerMux mode 0 */
-}
-
-static void init_usb_phy(void)
-{
- struct usb_common_regs *common0 = USB0_COMMON_BASE;
- struct usb_common_regs *common1 = USB1_COMMON_BASE;
- struct usb0_phy_regs *phy = USB0_PHY_BASE;
- struct usb1_port_regs *port = USB1_PORT_BASE;
- struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE;
-
- writew(0x0100, &phy->reset); /* set reset */
- /* port0 = USB0, port1 = USB1 */
- writew(0x0002, &phy->portsel);
- writel(0x0001, &port->port1sel); /* port1 = Host */
- writew(0x0111, &phy->reset); /* clear reset */
-
- writew(0x4000, &common0->suspmode);
- writew(0x4000, &common1->suspmode);
-
-#if defined(__LITTLE_ENDIAN)
- writel(0x00000000, &align->ehcidatac);
- writel(0x00000000, &align->ohcidatac);
-#endif
-}
-
-static void init_gether_mdio(void)
-{
- struct gpio_regs *gpio = GPIO_BASE;
-
- writew(readw(&gpio->pgcr) | 0x0004, &gpio->pgcr);
- writeb(readb(&gpio->pgdr) | 0x02, &gpio->pgdr); /* Use ET0-MDIO */
-}
-
-static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string)
-{
- struct ether_mac_regs *ether;
- unsigned char mac[6];
- unsigned long val;
-
- string_to_enetaddr(mac_string, mac);
-
- if (!channel)
- ether = GETHER0_MAC_BASE;
- else
- ether = GETHER1_MAC_BASE;
-
- val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
- writel(val, ðer->mahr);
- val = (mac[4] << 8) | mac[5];
- writel(val, ðer->malr);
-}
-
-/*****************************************************************
- * This PMB must be set on this timing. The lowlevel_init is run on
- * Area 0(phys 0x00000000), so we have to map it.
- *
- * The new PMB table is following:
- * ent virt phys v sz c wt
- * 0 0xa0000000 0x40000000 1 128M 0 1
- * 1 0xa8000000 0x48000000 1 128M 0 1
- * 2 0xb0000000 0x50000000 1 128M 0 1
- * 3 0xb8000000 0x58000000 1 128M 0 1
- * 4 0x80000000 0x40000000 1 128M 1 1
- * 5 0x88000000 0x48000000 1 128M 1 1
- * 6 0x90000000 0x50000000 1 128M 1 1
- * 7 0x98000000 0x58000000 1 128M 1 1
- */
-static void set_pmb_on_board_init(void)
-{
- struct mmu_regs *mmu = MMU_BASE;
-
- /* clear ITLB */
- writel(0x00000004, &mmu->mmucr);
-
- /* delete PMB for SPIBOOT */
- writel(0, PMB_ADDR_BASE(0));
- writel(0, PMB_DATA_BASE(0));
-
- /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */
- /* ppn ub v s1 s0 c wt */
- writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0));
- writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0));
- writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2));
- writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2));
- writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3));
- writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3));
- writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4));
- writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4));
- writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6));
- writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6));
- writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7));
- writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7));
-}
-
-int board_init(void)
-{
- init_gpio();
- set_pmb_on_board_init();
-
- init_usb_phy();
- init_gether_mdio();
-
- return 0;
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- struct gpio_regs *gpio = GPIO_BASE;
-
- writew(readw(&gpio->pgcr) | 0x0040, &gpio->pgcr);
- writeb(readb(&gpio->pgdr) & ~0x08, &gpio->pgdr); /* Reset */
- udelay(1);
- writeb(readb(&gpio->pgdr) | 0x08, &gpio->pgdr); /* Release reset */
- udelay(200);
-
- return mmcif_mmc_init();
-}
-
-static int get_sh_eth_mac_raw(unsigned char *buf, int size)
-{
-#ifdef CONFIG_DEPRECATED
- struct spi_flash *spi;
- int ret;
-
- spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
- if (spi == NULL) {
- printf("%s: spi_flash probe failed.\n", __func__);
- return 1;
- }
-
- ret = spi_flash_read(spi, SH7752EVB_ETHERNET_MAC_BASE, size, buf);
- if (ret) {
- printf("%s: spi_flash read failed.\n", __func__);
- spi_flash_free(spi);
- return 1;
- }
- spi_flash_free(spi);
-#endif
-
- return 0;
-}
-
-static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf)
-{
- memcpy(mac_string, &buf[channel * (SH7752EVB_ETHERNET_MAC_SIZE + 1)],
- SH7752EVB_ETHERNET_MAC_SIZE);
- mac_string[SH7752EVB_ETHERNET_MAC_SIZE] = 0x00; /* terminate */
-
- return 0;
-}
-
-static void init_ethernet_mac(void)
-{
- char mac_string[64];
- char env_string[64];
- int i;
- unsigned char *buf;
-
- buf = malloc(256);
- if (!buf) {
- printf("%s: malloc failed.\n", __func__);
- return;
- }
- get_sh_eth_mac_raw(buf, 256);
-
- /* Gigabit Ethernet */
- for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
- get_sh_eth_mac(i, mac_string, buf);
- if (i == 0)
- env_set("ethaddr", mac_string);
- else {
- sprintf(env_string, "eth%daddr", i);
- env_set(env_string, mac_string);
- }
- set_mac_to_sh_giga_eth_register(i, mac_string);
- }
-
- free(buf);
-}
-
-int board_late_init(void)
-{
- init_ethernet_mac();
-
- return 0;
-}
-
-#ifdef CONFIG_DEPRECATED
-int do_write_mac(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- int i, ret;
- char mac_string[256];
- struct spi_flash *spi;
- unsigned char *buf;
-
- if (argc != 3) {
- buf = malloc(256);
- if (!buf) {
- printf("%s: malloc failed.\n", __func__);
- return 1;
- }
-
- get_sh_eth_mac_raw(buf, 256);
-
- /* print current MAC address */
- for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
- get_sh_eth_mac(i, mac_string, buf);
- printf("GETHERC ch%d = %s\n", i, mac_string);
- }
- free(buf);
- return 0;
- }
-
- /* new setting */
- memset(mac_string, 0xff, sizeof(mac_string));
- sprintf(mac_string, "%s\t%s",
- argv[1], argv[2]);
-
- /* write MAC data to SPI rom */
- spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
- if (!spi) {
- printf("%s: spi_flash probe failed.\n", __func__);
- return 1;
- }
-
- ret = spi_flash_erase(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
- SH7752EVB_SPI_SECTOR_SIZE);
- if (ret) {
- printf("%s: spi_flash erase failed.\n", __func__);
- return 1;
- }
-
- ret = spi_flash_write(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
- sizeof(mac_string), mac_string);
- if (ret) {
- printf("%s: spi_flash write failed.\n", __func__);
- spi_flash_free(spi);
- return 1;
- }
- spi_flash_free(spi);
-
- puts("The writing of the MAC address to SPI ROM was completed.\n");
-
- return 0;
-}
-
-U_BOOT_CMD(
- write_mac, 3, 1, do_write_mac,
- "write MAC address for GETHERC",
- "[GETHERC ch0] [GETHERC ch1]\n"
-);
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2012 Renesas Solutions Corp.
- *
- * This file is subject to the terms and conditions of the GNU Lesser
- * General Public License. See the file "COPYING.LIB" in the main
- * directory of this archive for more details.
- */
-
-#include <common.h>
-
-#define CONFIG_RAM_BOOT_PHYS CONFIG_SYS_TEXT_BASE
-#define CONFIG_SPI_ADDR 0x00000000
-#define CONFIG_SPI_LENGTH CONFIG_SYS_MONITOR_LEN
-#define CONFIG_RAM_BOOT CONFIG_SYS_TEXT_BASE
-
-#define SPIWDMADR 0xFE001018
-#define SPIWDMCNTR 0xFE001020
-#define SPIDMCOR 0xFE001028
-#define SPIDMINTSR 0xFE001188
-#define SPIDMINTMR 0xFE001190
-
-#define SPIDMINTSR_DMEND 0x00000004
-
-#define TBR 0xFE002000
-#define RBR 0xFE002000
-
-#define CR1 0xFE002008
-#define CR2 0xFE002010
-#define CR3 0xFE002018
-#define CR4 0xFE002020
-
-/* CR1 */
-#define SPI_TBE 0x80
-#define SPI_TBF 0x40
-#define SPI_RBE 0x20
-#define SPI_RBF 0x10
-#define SPI_PFONRD 0x08
-#define SPI_SSDB 0x04
-#define SPI_SSD 0x02
-#define SPI_SSA 0x01
-
-/* CR2 */
-#define SPI_RSTF 0x80
-#define SPI_LOOPBK 0x40
-#define SPI_CPOL 0x20
-#define SPI_CPHA 0x10
-#define SPI_L1M0 0x08
-
-/* CR4 */
-#define SPI_TBEI 0x80
-#define SPI_TBFI 0x40
-#define SPI_RBEI 0x20
-#define SPI_RBFI 0x10
-#define SPI_SpiS0 0x02
-#define SPI_SSS 0x01
-
-#define spi_write(val, addr) (*(volatile unsigned long *)(addr)) = val
-#define spi_read(addr) (*(volatile unsigned long *)(addr))
-
-/* M25P80 */
-#define M25_READ 0x03
-
-#define __uses_spiboot2 __attribute__((section(".spiboot2.text")))
-static void __uses_spiboot2 spi_reset(void)
-{
- int timeout = 0x00100000;
-
- /* Make sure the last transaction is finalized */
- spi_write(0x00, CR3);
- spi_write(0x02, CR1);
- while (!(spi_read(CR4) & SPI_SpiS0)) {
- if (timeout-- < 0)
- break;
- }
- spi_write(0x00, CR1);
-
- spi_write(spi_read(CR2) | SPI_RSTF, CR2); /* fifo reset */
- spi_write(spi_read(CR2) & ~SPI_RSTF, CR2);
-
- spi_write(0, SPIDMCOR);
-}
-
-static void __uses_spiboot2 spi_read_flash(void *buf, unsigned long addr,
- unsigned long len)
-{
- spi_write(M25_READ, TBR);
- spi_write((addr >> 16) & 0xFF, TBR);
- spi_write((addr >> 8) & 0xFF, TBR);
- spi_write(addr & 0xFF, TBR);
-
- spi_write(SPIDMINTSR_DMEND, SPIDMINTSR);
- spi_write((unsigned long)buf, SPIWDMADR);
- spi_write(len & 0xFFFFFFE0, SPIWDMCNTR);
- spi_write(1, SPIDMCOR);
-
- spi_write(0xff, CR3);
- spi_write(spi_read(CR1) | SPI_SSDB, CR1);
- spi_write(spi_read(CR1) | SPI_SSA, CR1);
-
- while (!(spi_read(SPIDMINTSR) & SPIDMINTSR_DMEND))
- ;
-
- /* Nagate SP0-SS0 */
- spi_write(0, CR1);
-}
-
-void __uses_spiboot2 spiboot_main(void)
-{
- void (*_start)(void) = (void *)CONFIG_SYS_TEXT_BASE;
-
- spi_reset();
- spi_read_flash((void *)CONFIG_RAM_BOOT_PHYS, CONFIG_SPI_ADDR,
- CONFIG_SPI_LENGTH);
-
- _start();
-}
+++ /dev/null
-CONFIG_SH=y
-CONFIG_SYS_TEXT_BASE=0x5ff80000
-CONFIG_ENV_SIZE=0x10000
-CONFIG_SH_32BIT=y
-CONFIG_TARGET_SH7752EVB=y
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttySC2,115200 root=/dev/nfs ip=dhcp"
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_CONSOLE is not set
-# CONFIG_CMD_BOOTD is not set
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
-# CONFIG_CMD_EDITENV is not set
-# CONFIG_CMD_ENV_EXISTS is not set
-CONFIG_CMD_MD5SUM=y
-# CONFIG_CMD_LOADB is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SDRAM=y
-# CONFIG_CMD_ECHO is not set
-# CONFIG_CMD_ITEST is not set
-# CONFIG_CMD_SOURCE is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_SLEEP is not set
-CONFIG_CMD_EXT2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_MMC=y
-CONFIG_SH_MMCIF=y
-CONFIG_BITBANGMII=y
-CONFIG_PHY_VITESSE=y
-CONFIG_SH_ETHER=y
-CONFIG_SCIF_CONSOLE=y
-CONFIG_SPI=y
-CONFIG_USE_PRIVATE_LIBGCC=y
.. toctree::
:maxdepth: 2
- sh7752evb
sh7753evb
+++ /dev/null
-.. SPDX-License-Identifier: GPL-2.0+
-
-R0P7752C00000RZ board
-=====================
-
-This board specification
-------------------------
-
-The R0P7752C00000RZ(board config name:sh7752evb) has the following device:
-
- - SH7752 (SH-4A)
- - DDR3-SDRAM 512MB
- - SPI ROM 8MB
- - Gigabit Ethernet controllers
- - eMMC 4GB
-
-
-Configuration for This board
-----------------------------
-
-You can select the configuration as follows:
-
- - make sh7752evb_config
-
-
-This board specific command
----------------------------
-
-This board has the following its specific command:
-
-write_mac:
- You can write MAC address to SPI ROM.
-
-Usage 1: Write MAC address
-
-.. code-block:: none
-
- write_mac [GETHERC ch0] [GETHERC ch1]
-
- For example:
- => write_mac 74:90:50:00:33:9e 74:90:50:00:33:9f
-
-* We have to input the command as a single line (without carriage return)
-* We have to reset after input the command.
-
-Usage 2: Show current data
-
-.. code-block:: none
-
- write_mac
-
- For example:
- => write_mac
- GETHERC ch0 = 74:90:50:00:33:9e
- GETHERC ch1 = 74:90:50:00:33:9f
-
-
-Update SPI ROM
---------------
-
-1. Copy u-boot image to RAM area.
-2. Probe SPI device.
-
-.. code-block:: none
-
- => sf probe 0
- SF: Detected MX25L6405D with page size 64KiB, total 8 MiB
-
-3. Erase SPI ROM.
-
-.. code-block:: none
-
- => sf erase 0 80000
-
-4. Write u-boot image to SPI ROM.
-
-.. code-block:: none
-
- => sf write 0x48000000 0 80000
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Configuation settings for the sh7752evb board
- *
- * Copyright (C) 2012 Renesas Solutions Corp.
- */
-
-#ifndef __SH7752EVB_H
-#define __SH7752EVB_H
-
-#define CONFIG_CPU_SH7752 1
-
-#define CONFIG_DISPLAY_BOARDINFO
-
-/* MEMORY */
-#define SH7752EVB_SDRAM_BASE (0x40000000)
-#define SH7752EVB_SDRAM_SIZE (512 * 1024 * 1024)
-
-#define CONFIG_SYS_PBSIZE 256
-#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
-
-/* SCIF */
-#define CONFIG_CONS_SCIF2 1
-
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE
-
-#define CONFIG_SYS_SDRAM_BASE (SH7752EVB_SDRAM_BASE)
-#define CONFIG_SYS_SDRAM_SIZE (SH7752EVB_SDRAM_SIZE)
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + \
- 128 * 1024 * 1024)
-
-#define CONFIG_SYS_MONITOR_BASE 0x00000000
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
-
-/* Ether */
-#define CONFIG_SH_ETHER_USE_PORT 0
-#define CONFIG_SH_ETHER_PHY_ADDR 18
-#define CONFIG_SH_ETHER_CACHE_WRITEBACK 1
-#define CONFIG_SH_ETHER_USE_GETHER 1
-#define CONFIG_BITBANGMII_MULTI
-#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RGMII
-
-#define SH7752EVB_ETHERNET_MAC_BASE_SPI 0x00090000
-#define SH7752EVB_SPI_SECTOR_SIZE (64 * 1024)
-#define SH7752EVB_ETHERNET_MAC_BASE SH7752EVB_ETHERNET_MAC_BASE_SPI
-#define SH7752EVB_ETHERNET_MAC_SIZE 17
-#define SH7752EVB_ETHERNET_NUM_CH 2
-
-/* SPI */
-#define CONFIG_SH_SPI_BASE 0xfe002000
-
-/* MMCIF */
-#define CONFIG_SH_MMCIF_ADDR 0xffcb0000
-#define CONFIG_SH_MMCIF_CLK 48000000
-
-/* ENV setting */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netboot=bootp; bootm\0"
-
-/* Board Clock */
-#define CONFIG_SYS_CLK_FREQ 48000000
-#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
-#endif /* __SH7752EVB_H */
projects / u-boot.git / commitdiff
