ppc: malta: Drop use of DM_PCI

Now that DM_PCI is always enabled we don't need to check it. Drop this
old code.

Signed-off-by: Simon Glass <sjg@chromium.org>

diff --git a/board/imgtec/malta/malta.c b/board/imgtec/malta/malta.c
index 9af1f92e5db79d54e7caf5bfa94872aae68dfbcf..d2e2e4ae2093c563e961325a8916fd71bab81d0c 100644 (file)
--- a/board/imgtec/malta/malta.c
+++ b/board/imgtec/malta/malta.c
@@ -196,7 +196,6 @@ int board_fix_fdt(void *rw_fdt_blob)
 }
 #endif
 
-#if IS_ENABLED(CONFIG_DM_PCI)
 int board_early_init_r(void)
 {
        struct udevice *dev;
@@ -243,69 +242,3 @@ int board_early_init_r(void)
 
        return 0;
 }
-#else
-void pci_init_board(void)
-{
-       pci_dev_t bdf;
-       u32 val32;
-       u8 val8;
-
-       switch (malta_sys_con()) {
-       case SYSCON_GT64120:
-               gt64120_pci_init((void *)CKSEG1ADDR(MALTA_GT_BASE),
-                                0x00000000, 0x00000000, CONFIG_SYS_MEM_SIZE,
-                                0x10000000, 0x10000000, 128 * 1024 * 1024,
-                                0x00000000, 0x00000000, 0x20000);
-               break;
-
-       default:
-       case SYSCON_MSC01:
-               msc01_pci_init((void *)CKSEG1ADDR(MALTA_MSC01_PCI_BASE),
-                              0x00000000, 0x00000000, CONFIG_SYS_MEM_SIZE,
-                              MALTA_MSC01_PCIMEM_MAP,
-                              CKSEG1ADDR(MALTA_MSC01_PCIMEM_BASE),
-                              MALTA_MSC01_PCIMEM_SIZE, MALTA_MSC01_PCIIO_MAP,
-                              0x00000000, MALTA_MSC01_PCIIO_SIZE);
-               break;
-       }
-
-       bdf = pci_find_device(PCI_VENDOR_ID_INTEL,
-                             PCI_DEVICE_ID_INTEL_82371AB_0, 0);
-       if (bdf == -1)
-               panic("Failed to find PIIX4 PCI bridge\n");
-
-       /* setup PCI interrupt routing */
-       pci_write_config_byte(bdf, PCI_CFG_PIIX4_PIRQRCA, 10);
-       pci_write_config_byte(bdf, PCI_CFG_PIIX4_PIRQRCB, 10);
-       pci_write_config_byte(bdf, PCI_CFG_PIIX4_PIRQRCC, 11);
-       pci_write_config_byte(bdf, PCI_CFG_PIIX4_PIRQRCD, 11);
-
-       /* mux SERIRQ onto SERIRQ pin */
-       pci_read_config_dword(bdf, PCI_CFG_PIIX4_GENCFG, &val32);
-       val32 |= PCI_CFG_PIIX4_GENCFG_SERIRQ;
-       pci_write_config_dword(bdf, PCI_CFG_PIIX4_GENCFG, val32);
-
-       /* enable SERIRQ - Linux currently depends upon this */
-       pci_read_config_byte(bdf, PCI_CFG_PIIX4_SERIRQC, &val8);
-       val8 |= PCI_CFG_PIIX4_SERIRQC_EN | PCI_CFG_PIIX4_SERIRQC_CONT;
-       pci_write_config_byte(bdf, PCI_CFG_PIIX4_SERIRQC, val8);
-
-       bdf = pci_find_device(PCI_VENDOR_ID_INTEL,
-                             PCI_DEVICE_ID_INTEL_82371AB, 0);
-       if (bdf == -1)
-               panic("Failed to find PIIX4 IDE controller\n");
-
-       /* enable bus master & IO access */
-       val32 |= PCI_COMMAND_MASTER | PCI_COMMAND_IO;
-       pci_write_config_dword(bdf, PCI_COMMAND, val32);
-
-       /* set latency */
-       pci_write_config_byte(bdf, PCI_LATENCY_TIMER, 0x40);
-
-       /* enable IDE/ATA */
-       pci_write_config_dword(bdf, PCI_CFG_PIIX4_IDETIM_PRI,
-                              PCI_CFG_PIIX4_IDETIM_IDE);
-       pci_write_config_dword(bdf, PCI_CFG_PIIX4_IDETIM_SEC,
-                              PCI_CFG_PIIX4_IDETIM_IDE);
-}
-#endif