This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
select SYS_FSL_DDR_BE
select SYS_FSL_HAS_DDR2
-config TARGET_MPC837XEMDS
- bool "Support MPC837XEMDS"
- select ARCH_MPC837X
- select BOARD_EARLY_INIT_F
- imply CMD_SATA
- imply FSL_SATA
-
config TARGET_MPC837XERDB
bool "Support MPC837XERDB"
select ARCH_MPC837X
source "board/freescale/mpc8323erdb/Kconfig"
source "board/freescale/mpc832xemds/Kconfig"
source "board/freescale/mpc8349emds/Kconfig"
-source "board/freescale/mpc837xemds/Kconfig"
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
source "board/keymile/Kconfig"
+++ /dev/null
-if TARGET_MPC837XEMDS
-
-config SYS_BOARD
- default "mpc837xemds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC837XEMDS"
-
-endif
+++ /dev/null
-MPC837XEMDS BOARD
-#M: Dave Liu <daveliu@freescale.com>
-S: Orphan (since 2018-05)
-F: board/freescale/mpc837xemds/
-F: include/configs/MPC837XEMDS.h
-F: configs/MPC837XEMDS_defconfig
-F: configs/MPC837XEMDS_SLAVE_defconfig
-F: configs/MPC837XEMDS_HOST_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += mpc837xemds.o
-obj-$(CONFIG_PCI) += pci.o
+++ /dev/null
-Freescale MPC837xEMDS Board
------------------------------------------
-1. Board Switches and Jumpers
-1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC837xEMDS board
- For some reason, the HW designers describe the switch settings
- in terms of 0 and 1, and then map that to physical switches where
- the label "On" refers to logic 0 and "Off" is logic 1.
-
- Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
- bits may contribute to signals that are numbered based at 0,
- and some of those signals may be high-bit-number-0 too. Heed
- well the names and labels and do not get confused.
-
- "Off" == 1
- "On" == 0
-
- SW4[8] is the bit labeled 8 on Switch 4.
- SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2.
- SW2[1:8]= 0000_0001 refers to bits labeled 1 through 7 is set as "On"
- and bits labeled 8 is set as "Off".
-
-1.1 For the MPC837xEMDS Processor Board
-
- First, make sure the board default setting is consistent with the
- document shipped with your board. Then apply the following setting:
- SW3[1-8]= 0011_0000 (BOOTSEQ, ROMLOC setting)
- SW4[1-8]= 0000_0110 (core PLL setting)
- SW5[1-8]= 1001_1000 (system PLL, boot up from low end of flash)
- SW6[1-8]= 0000_1000 (HRCW is read from NOR FLASH)
- SW7[1-8]= 0110_1101 (TSEC1/2 interface setting - RGMII)
- J3 2-3, TSEC1 LVDD1 with 2.5V
- J6 2-3, TSEC2 LVDD2 with 2.5V
- J9 2-3, CLKIN from osc on board
- J10 removed, CS0 connect to NOR flash; when mounted, CS0 connect to NAND
- J11 removed, Hardware Reset Configuration Word load from FLASH(NOR or NAND)
- mounted, HRCW load from BCSR.
-
- on board Oscillator: 66M
-
-2. Memory Map
-
-2.1. The memory map should look pretty much like this:
-
- 0x0000_0000 0x7fff_ffff DDR 2G
- 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M
- 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M
- 0xc000_0000 0xdfff_ffff Empty 512M
- 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M
- 0xe010_0000 0xe02f_ffff Empty 2M
- 0xe030_0000 0xe03f_ffff PCI IO 1M
- 0xe040_0000 0xe05f_ffff Empty 2M
- 0xe060_0000 0xe060_7fff NAND Flash 32K
- 0xf400_0000 0xf7ff_ffff Empty 64M
- 0xf800_0000 0xf800_7fff BCSR on CS1 32K
- 0xfe00_0000 0xffff_ffff NOR Flash on CS0 32M
-
-3. Definitions
-
-3.1 Explanation of NEW definitions in:
-
- include/configs/MPC837XEMDS.h
-
- CONFIG_MPC83xx MPC83xx family for both MPC837x and MPC8360
- CONFIG_MPC837x MPC837x specific
- CONFIG_MPC837XEMDS MPC837XEMDS board specific
-
-4. Compilation
-
- Assuming you're using BASH shell:
-
- export CROSS_COMPILE=your-cross-compile-prefix
- cd u-boot
- make distclean
- make MPC837XEMDS_config
- make
-
-5. Downloading and Flashing Images
-
-5.0 Download over serial line using Kermit:
-
- loadb
- [Drop to kermit:
- ^\c
- send <u-boot-bin-image>
- c
- ]
-
-
- Or via tftp:
-
- tftp 40000 u-boot.bin
-
-5.1 Reflash U-Boot Image using U-Boot
-
- tftp 40000 u-boot.bin
- protect off fe000000 fe1fffff
- erase fe000000 fe1fffff
-
- cp.b 40000 fe000000 xxxx
-
-You have to supply the correct byte count with 'xxxx' from the TFTP result log.
-
-6. Notes
- 1) The console baudrate for MPC837XEMDS is 115200bps.
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2007,2010 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- */
-
-#include <common.h>
-#include <hwconfig.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <asm/bitops.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-#include <spd_sdram.h>
-#include <tsec.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <fsl_esdhc.h>
-#include <fsl_mdio.h>
-#include <phy.h>
-#include "pci.h"
-#include "../common/pq-mds-pib.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
-
- /* Enable flash write */
- bcsr[0x9] &= ~0x04;
- /* Clear all of the interrupt of BCSR */
- bcsr[0xe] = 0xff;
-
-#ifdef CONFIG_FSL_SERDES
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- u32 spridr = in_be32(&immr->sysconf.spridr);
-
- /* we check only part num, and don't look for CPU revisions */
- switch (PARTID_NO_E(spridr)) {
- case SPR_8377:
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- break;
- case SPR_8378:
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
- FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
- break;
- case SPR_8379:
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_SATA,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- break;
- default:
- printf("serdes not configured: unknown CPU part number: "
- "%04x\n", spridr >> 16);
- break;
- }
-#endif /* CONFIG_FSL_SERDES */
- return 0;
-}
-
-#ifdef CONFIG_FSL_ESDHC
-int board_mmc_init(struct bd_info *bd)
-{
- struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
-
- if (!hwconfig("esdhc"))
- return 0;
-
- /* Set SPI_SD, SER_SD, and IRQ4_WP so that SD signals go through */
- bcsr[0xc] |= 0x4c;
-
- /* Set proper bits in SICR to allow SD signals through */
- clrsetbits_be32(&im->sysconf.sicrl, SICRL_USB_B, SICRL_USB_B_SD);
- clrsetbits_be32(&im->sysconf.sicrh, SICRH_GPIO2_E | SICRH_SPI,
- SICRH_GPIO2_E_SD | SICRH_SPI_SD);
-
- return fsl_esdhc_mmc_init(bd);
-}
-#endif
-
-#if defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2)
-int board_eth_init(struct bd_info *bd)
-{
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[2];
- struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
- u32 rcwh = in_be32(&im->reset.rcwh);
- u32 tsec_mode;
- int num = 0;
-
- /* New line after Net: */
- printf("\n");
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
-
- printf(CONFIG_TSEC1_NAME ": ");
-
- tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
- if (tsec_mode == HRCWH_TSEC1M_IN_RGMII) {
- printf("RGMII\n");
- /* this is default, no need to fixup */
- } else if (tsec_mode == HRCWH_TSEC1M_IN_SGMII) {
- printf("SGMII\n");
- tsec_info[num].phyaddr = TSEC1_PHY_ADDR_SGMII;
- tsec_info[num].flags = TSEC_GIGABIT;
- } else {
- printf("unsupported PHY type\n");
- }
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
-
- printf(CONFIG_TSEC2_NAME ": ");
-
- tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
- if (tsec_mode == HRCWH_TSEC2M_IN_RGMII) {
- printf("RGMII\n");
- /* this is default, no need to fixup */
- } else if (tsec_mode == HRCWH_TSEC2M_IN_SGMII) {
- printf("SGMII\n");
- tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII;
- tsec_info[num].flags = TSEC_GIGABIT;
- } else {
- printf("unsupported PHY type\n");
- }
- num++;
-#endif
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
- fsl_pq_mdio_init(bd, &mdio_info);
-
- return tsec_eth_init(bd, tsec_info, num);
-}
-
-static void __ft_tsec_fixup(void *blob, struct bd_info *bd, const char *alias,
- int phy_addr)
-{
- const u32 *ph;
- int off;
- int err;
-
- off = fdt_path_offset(blob, alias);
- if (off < 0) {
- printf("WARNING: could not find %s alias: %s.\n", alias,
- fdt_strerror(off));
- return;
- }
-
- err = fdt_fixup_phy_connection(blob, off, PHY_INTERFACE_MODE_SGMII);
-
- if (err) {
- printf("WARNING: could not set phy-connection-type for %s: "
- "%s.\n", alias, fdt_strerror(err));
- return;
- }
-
- ph = (u32 *)fdt_getprop(blob, off, "phy-handle", 0);
- if (!ph) {
- printf("WARNING: could not get phy-handle for %s.\n",
- alias);
- return;
- }
-
- off = fdt_node_offset_by_phandle(blob, *ph);
- if (off < 0) {
- printf("WARNING: could not get phy node for %s: %s\n", alias,
- fdt_strerror(off));
- return;
- }
-
- phy_addr = cpu_to_fdt32(phy_addr);
- err = fdt_setprop(blob, off, "reg", &phy_addr, sizeof(phy_addr));
- if (err < 0) {
- printf("WARNING: could not set phy node's reg for %s: "
- "%s.\n", alias, fdt_strerror(err));
- return;
- }
-}
-
-static void ft_tsec_fixup(void *blob, struct bd_info *bd)
-{
- struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
- u32 rcwh = in_be32(&im->reset.rcwh);
- u32 tsec_mode;
-
-#ifdef CONFIG_TSEC1
- tsec_mode = rcwh & HRCWH_TSEC1M_MASK;
- if (tsec_mode == HRCWH_TSEC1M_IN_SGMII)
- __ft_tsec_fixup(blob, bd, "ethernet0", TSEC1_PHY_ADDR_SGMII);
-#endif
-
-#ifdef CONFIG_TSEC2
- tsec_mode = rcwh & HRCWH_TSEC2M_MASK;
- if (tsec_mode == HRCWH_TSEC2M_IN_SGMII)
- __ft_tsec_fixup(blob, bd, "ethernet1", TSEC2_PHY_ADDR_SGMII);
-#endif
-}
-#else
-static inline void ft_tsec_fixup(void *blob, struct bd_info *bd) {}
-#endif /* defined(CONFIG_TSEC1) || defined(CONFIG_TSEC2) */
-
-int board_early_init_r(void)
-{
-#ifdef CONFIG_PQ_MDS_PIB
- pib_init();
-#endif
- return 0;
-}
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-int fixed_sdram(void);
-
-int dram_init(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
- return -ENXIO;
-
-#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
-#else
- msize = fixed_sdram();
-#endif
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /* Initialize DDR ECC byte */
- ddr_enable_ecc(msize * 1024 * 1024);
-#endif
-
- /* return total bus DDR size(bytes) */
- gd->ram_size = msize * 1024 * 1024;
-
- return 0;
-}
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
- u32 msize_log2 = __ilog2(msize);
-
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE & 0xfffff000;
- im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
-
-#if (CONFIG_SYS_DDR_SIZE != 512)
-#warning Currenly any ddr size other than 512 is not supported
-#endif
- im->sysconf.ddrcdr = CONFIG_SYS_DDRCDR_VALUE;
- udelay(50000);
-
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_SDRAM_CLK_CNTL;
- udelay(1000);
-
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- udelay(1000);
-
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- __asm__ __volatile__("sync");
- udelay(1000);
-
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
- udelay(2000);
- return CONFIG_SYS_DDR_SIZE;
-}
-#endif /*!CONFIG_SYS_SPD_EEPROM */
-
-int checkboard(void)
-{
- puts("Board: Freescale MPC837xEMDS\n");
- return 0;
-}
-
-#ifdef CONFIG_PCI
-int board_pci_host_broken(void)
-{
- struct immap __iomem *im = (struct immap __iomem *)CONFIG_SYS_IMMR;
- const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST;
-
- /* It's always OK in case of external arbiter. */
- if (hwconfig_subarg_cmp("pci", "arbiter", "external"))
- return 0;
-
- if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask)
- return 1;
-
- return 0;
-}
-
-static void ft_pci_fixup(void *blob, struct bd_info *bd)
-{
- const char *status = "broken (no arbiter)";
- int off;
- int err;
-
- off = fdt_path_offset(blob, "pci0");
- if (off < 0) {
- printf("WARNING: could not find pci0 alias: %s.\n",
- fdt_strerror(off));
- return;
- }
-
- err = fdt_setprop(blob, off, "status", status, strlen(status) + 1);
- if (err) {
- printf("WARNING: could not set status for pci0: %s.\n",
- fdt_strerror(err));
- return;
- }
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
- ft_tsec_fixup(blob, bd);
- fsl_fdt_fixup_dr_usb(blob, bd);
- fdt_fixup_esdhc(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
- if (board_pci_host_broken())
- ft_pci_fixup(blob, bd);
- ft_pcie_fixup(blob, bd);
-#endif
-
- return 0;
-}
-#endif /* CONFIG_OF_BOARD_SETUP */
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- */
-
-#include <init.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <common.h>
-#include <env.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <i2c.h>
-#include <fdt_support.h>
-#include <asm/fsl_i2c.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-#include <linux/delay.h>
-
-static struct pci_region pci_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI_MEM_BASE,
- phys_start: CONFIG_SYS_PCI_MEM_PHYS,
- size: CONFIG_SYS_PCI_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI_MMIO_PHYS,
- size: CONFIG_SYS_PCI_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
- {
- bus_start: CONFIG_SYS_PCI_IO_BASE,
- phys_start: CONFIG_SYS_PCI_IO_PHYS,
- size: CONFIG_SYS_PCI_IO_SIZE,
- flags: PCI_REGION_IO
- }
-};
-
-static struct pci_region pcie_regions_0[] = {
- {
- .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
- .size = CONFIG_SYS_PCIE1_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
- .size = CONFIG_SYS_PCIE1_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-static struct pci_region pcie_regions_1[] = {
- {
- .bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
- .size = CONFIG_SYS_PCIE2_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE2_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
- .size = CONFIG_SYS_PCIE2_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-static int is_pex_x2(void)
-{
- const char *pex_x2 = env_get("pex_x2");
-
- if (pex_x2 && !strcmp(pex_x2, "yes"))
- return 1;
- return 0;
-}
-
-void pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile sysconf83xx_t *sysconf = &immr->sysconf;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- volatile law83xx_t *pcie_law = sysconf->pcielaw;
- struct pci_region *reg[] = { pci_regions };
- struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
- u32 spridr = in_be32(&immr->sysconf.spridr);
- int pex2 = is_pex_x2();
-
- if (board_pci_host_broken())
- goto skip_pci;
-
- /* Enable all 5 PCI_CLK_OUTPUTS */
- clk->occr |= 0xf8000000;
- udelay(2000);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
-
- pci_law[1].bar = CONFIG_SYS_PCI_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- udelay(2000);
-
- mpc83xx_pci_init(1, reg);
-skip_pci:
- /* There is no PEX in MPC8379 parts. */
- if (PARTID_NO_E(spridr) == SPR_8379)
- return;
-
- if (pex2)
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX_X2,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- else
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-
- /* Configure the clock for PCIE controller */
- clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
- SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
-
- /* Deassert the resets in the control register */
- out_be32(&sysconf->pecr1, 0xE0008000);
- if (!pex2)
- out_be32(&sysconf->pecr2, 0xE0008000);
- udelay(2000);
-
- /* Configure PCI Express Local Access Windows */
- out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- mpc83xx_pcie_init(pex2 ? 1 : 2, pcie_reg);
-}
-
-void ft_pcie_fixup(void *blob, struct bd_info *bd)
-{
- const char *status = "disabled (PCIE1 is x2)";
-
- if (!is_pex_x2())
- return;
-
- do_fixup_by_path(blob, "pci2", "status", status,
- strlen(status) + 1, 1);
-}
+++ /dev/null
-#ifndef __BOARD_MPC837XEMDS_PCI_H
-#define __BOARD_MPC837XEMDS_PCI_H
-
-extern void ft_pcie_fixup(void *blob, struct bd_info *bd);
-
-#endif /* __BOARD_MPC837XEMDS_PCI_H */
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_MPC837XEMDS=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_6_1=y
-CONFIG_CORE_PLL_RATIO_15_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_RGMII=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_LDP_PIN_MUX_STATE_0=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM_LOWER"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="SDRAM_UPPER"
-CONFIG_BAT1_BASE=0x10000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="IMMR"
-CONFIG_BAT2_BASE=0xE0000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_INHIBITED=y
-CONFIG_BAT2_ICACHE_GUARDED=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="BCSR"
-CONFIG_BAT3_BASE=0xF8000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_INHIBITED=y
-CONFIG_BAT3_ICACHE_GUARDED=y
-CONFIG_BAT3_DCACHE_INHIBITED=y
-CONFIG_BAT3_DCACHE_GUARDED=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="FLASH"
-CONFIG_BAT4_BASE=0xFE000000
-CONFIG_BAT4_LENGTH_32_MBYTES=y
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_DCACHE_INHIBITED=y
-CONFIG_BAT4_DCACHE_GUARDED=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="STACK_IN_DCACHE"
-CONFIG_BAT5_BASE=0xE6000000
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="PCI_MEM"
-CONFIG_BAT6_BASE=0x80000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT7=y
-CONFIG_BAT7_NAME="PCI_MMIO"
-CONFIG_BAT7_BASE=0x90000000
-CONFIG_BAT7_LENGTH_256_MBYTES=y
-CONFIG_BAT7_ACCESS_RW=y
-CONFIG_BAT7_ICACHE_INHIBITED=y
-CONFIG_BAT7_ICACHE_GUARDED=y
-CONFIG_BAT7_DCACHE_INHIBITED=y
-CONFIG_BAT7_DCACHE_GUARDED=y
-CONFIG_BAT7_USER_MODE_VALID=y
-CONFIG_BAT7_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_32_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xF8000000
-CONFIG_LBLAW1_NAME="BCSR"
-CONFIG_LBLAW1_LENGTH_32_KBYTES=y
-CONFIG_LBLAW3=y
-CONFIG_LBLAW3_BASE=0xE0600000
-CONFIG_LBLAW3_NAME="NAND"
-CONFIG_LBLAW3_LENGTH_32_KBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_32_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="BCSR"
-CONFIG_BR1_OR1_BASE=0xF8000000
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_15=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_OR1_XACS_EXTENDED=y
-CONFIG_OR1_TRLX_RELAXED=y
-CONFIG_OR1_EHTR_8_CYCLE=y
-CONFIG_OR1_EAD_EXTRA=y
-CONFIG_ELBC_BR3_OR3=y
-CONFIG_BR3_OR3_NAME="NAND"
-CONFIG_BR3_OR3_BASE=0xE0600000
-CONFIG_BR3_ERRORCHECKING_BOTH=y
-CONFIG_BR3_MACHINE_FCM=y
-CONFIG_OR3_BCTLD_NOT_ASSERTED=y
-CONFIG_OR3_SCY_1=y
-CONFIG_OR3_CST_ONE_CLOCK=y
-CONFIG_OR3_CHT_TWO_CLOCK=y
-CONFIG_OR3_RST_ONE_CLOCK=y
-CONFIG_OR3_TRLX_RELAXED=y
-CONFIG_OR3_EHTR_8_CYCLE=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_8=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_ADDR=0xFE080000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC837XEMDS=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_6_1=y
-CONFIG_CORE_PLL_RATIO_15_1=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_RGMII=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_LDP_PIN_MUX_STATE_0=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM_LOWER"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="SDRAM_UPPER"
-CONFIG_BAT1_BASE=0x10000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="IMMR"
-CONFIG_BAT2_BASE=0xE0000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_INHIBITED=y
-CONFIG_BAT2_ICACHE_GUARDED=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="BCSR"
-CONFIG_BAT3_BASE=0xF8000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_INHIBITED=y
-CONFIG_BAT3_ICACHE_GUARDED=y
-CONFIG_BAT3_DCACHE_INHIBITED=y
-CONFIG_BAT3_DCACHE_GUARDED=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_32_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xF8000000
-CONFIG_LBLAW1_NAME="BCSR"
-CONFIG_LBLAW1_LENGTH_32_KBYTES=y
-CONFIG_LBLAW3=y
-CONFIG_LBLAW3_BASE=0xE0600000
-CONFIG_LBLAW3_NAME="NAND"
-CONFIG_LBLAW3_LENGTH_32_KBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_32_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="BCSR"
-CONFIG_BR1_OR1_BASE=0xF8000000
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_15=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_OR1_XACS_EXTENDED=y
-CONFIG_OR1_TRLX_RELAXED=y
-CONFIG_OR1_EHTR_8_CYCLE=y
-CONFIG_OR1_EAD_EXTRA=y
-CONFIG_ELBC_BR3_OR3=y
-CONFIG_BR3_OR3_NAME="NAND"
-CONFIG_BR3_OR3_BASE=0xE0600000
-CONFIG_BR3_ERRORCHECKING_BOTH=y
-CONFIG_BR3_MACHINE_FCM=y
-CONFIG_OR3_BCTLD_NOT_ASSERTED=y
-CONFIG_OR3_SCY_1=y
-CONFIG_OR3_CST_ONE_CLOCK=y
-CONFIG_OR3_CHT_TWO_CLOCK=y
-CONFIG_OR3_RST_ONE_CLOCK=y
-CONFIG_OR3_TRLX_RELAXED=y
-CONFIG_OR3_EHTR_8_CYCLE=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_8=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="PCISLAVE"
-CONFIG_BOOTDELAY=6
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_ADDR=0xFE080000
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66000000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_MPC837XEMDS=y
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_6_1=y
-CONFIG_CORE_PLL_RATIO_15_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_RGMII=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_LDP_PIN_MUX_STATE_0=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM_LOWER"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="SDRAM_UPPER"
-CONFIG_BAT1_BASE=0x10000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="IMMR"
-CONFIG_BAT2_BASE=0xE0000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_INHIBITED=y
-CONFIG_BAT2_ICACHE_GUARDED=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="BCSR"
-CONFIG_BAT3_BASE=0xF8000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_INHIBITED=y
-CONFIG_BAT3_ICACHE_GUARDED=y
-CONFIG_BAT3_DCACHE_INHIBITED=y
-CONFIG_BAT3_DCACHE_GUARDED=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="FLASH"
-CONFIG_BAT4_BASE=0xFE000000
-CONFIG_BAT4_LENGTH_32_MBYTES=y
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_DCACHE_INHIBITED=y
-CONFIG_BAT4_DCACHE_GUARDED=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="STACK_IN_DCACHE"
-CONFIG_BAT5_BASE=0xE6000000
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_32_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xF8000000
-CONFIG_LBLAW1_NAME="BCSR"
-CONFIG_LBLAW1_LENGTH_32_KBYTES=y
-CONFIG_LBLAW3=y
-CONFIG_LBLAW3_BASE=0xE0600000
-CONFIG_LBLAW3_NAME="NAND"
-CONFIG_LBLAW3_LENGTH_32_KBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_32_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="BCSR"
-CONFIG_BR1_OR1_BASE=0xF8000000
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_15=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_OR1_XACS_EXTENDED=y
-CONFIG_OR1_TRLX_RELAXED=y
-CONFIG_OR1_EHTR_8_CYCLE=y
-CONFIG_OR1_EAD_EXTRA=y
-CONFIG_ELBC_BR3_OR3=y
-CONFIG_BR3_OR3_NAME="NAND"
-CONFIG_BR3_OR3_BASE=0xE0600000
-CONFIG_BR3_ERRORCHECKING_BOTH=y
-CONFIG_BR3_MACHINE_FCM=y
-CONFIG_OR3_BCTLD_NOT_ASSERTED=y
-CONFIG_OR3_SCY_1=y
-CONFIG_OR3_CST_ONE_CLOCK=y
-CONFIG_OR3_CHT_TWO_CLOCK=y
-CONFIG_OR3_RST_ONE_CLOCK=y
-CONFIG_OR3_TRLX_RELAXED=y
-CONFIG_OR3_EHTR_8_CYCLE=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_8=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_ADDR=0xFE080000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-# CONFIG_PCI is not set
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-
-/*
- * IP blocks clock configuration
- */
-#define CONFIG_SYS_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */
-#define CONFIG_SYS_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */
-#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000000
-#define CONFIG_SYS_SICRL 0x00000000
-
-/*
- * Output Buffer Impedance
- */
-#define CONFIG_SYS_OBIR 0x31100000
-
-#define CONFIG_HWCONFIG
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
- | DDRCDR_ODT \
- | DDRCDR_Q_DRN)
- /* 0x80080001 */ /* ODT 150ohm on SoC */
-
-#undef CONFIG_DDR_ECC /* support DDR ECC function */
-#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
-
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
-
-#if defined(CONFIG_SPD_EEPROM)
-#define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */
-#else
-/*
- * Manually set up DDR parameters
- * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
- * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
- */
-#define CONFIG_SYS_DDR_SIZE 512 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ODT_RD_NEVER /* ODT_RD to none */ \
- | CSCONFIG_ODT_WR_ONLY_CURRENT /* ODT_WR to CSn */ \
- | CSCONFIG_ROW_BIT_14 \
- | CSCONFIG_COL_BIT_10)
- /* 0x80010202 */
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
- | (0 << TIMING_CFG0_WRT_SHIFT) \
- | (0 << TIMING_CFG0_RRT_SHIFT) \
- | (0 << TIMING_CFG0_WWT_SHIFT) \
- | (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
- | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
- /* 0x00620802 */
-#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
- | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
- | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
- | (5 << TIMING_CFG1_CASLAT_SHIFT) \
- | (13 << TIMING_CFG1_REFREC_SHIFT) \
- | (3 << TIMING_CFG1_WRREC_SHIFT) \
- | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
- | (2 << TIMING_CFG1_WRTORD_SHIFT))
- /* 0x3935d322 */
-#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
- | (6 << TIMING_CFG2_CPO_SHIFT) \
- | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
- | (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
- | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
- | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
- | (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
- /* 0x131088c8 */
-#define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
- /* 0x03E00100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
- | (0x1432 << SDRAM_MODE_SD_SHIFT))
- /* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2 0x00000000
-#endif
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-/*
- * BCSR on the Local Bus
- */
-#define CONFIG_SYS_BCSR 0xF8000000
- /* Access window base at BCSR base */
-
-/*
- * NAND Flash on the Local Bus
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_FSL_ELBC 1
-
-#define CONFIG_SYS_NAND_BASE 0xE0600000
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
-
-/*
- * Config on-board RTC
- */
-#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */
-
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
-#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
-
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-
-#define CONFIG_SYS_PCIE2_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#ifndef __ASSEMBLY__
-extern int board_pci_host_broken(void);
-#endif
-#define CONFIG_PCIE
-#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */
-
-#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-#endif /* CONFIG_PCI */
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC1"
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 3
-#define TSEC1_PHY_ADDR_SGMII 8
-#define TSEC2_PHY_ADDR_SGMII 4
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC1"
-
-/* SERDES */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1 0xe3000
-#define CONFIG_FSL_SERDES2 0xe3100
-
-/*
- * SATA
- */
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET 0x18000
-#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET 0x19000
-#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-
-#ifdef CONFIG_FSL_SATA
-#define CONFIG_LBA48
-#endif
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC_PIN_MUX
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=1000000\0" \
- "ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=780000\0" \
- "fdtfile=mpc8379_mds.dtb\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff
