dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
at91-sama5d2_xplained.dtb
+dtb-$(CONFIG_TARGET_SAMA5D27_SOM1_EK) += \
+ at91-sama5d27_som1_ek.dtb
+
dtb-$(CONFIG_TARGET_SAMA5D3XEK) += \
sama5d31ek.dtb \
sama5d33ek.dtb \
--- /dev/null
+/*
+ * at91-sama5d27_som1_ek.dts - Device Tree file for SAMA5D27 SOM1 EK board
+ *
+ * Copyright (C) 2017 Microchip Corporation
+ * Wenyou Yang <wenyou.yang@microchip.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d27_som1.dtsi"
+
+/ {
+ model = "Atmel SAMA5D27 SOM1 EK";
+ compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d2", "atmel,sama5";
+
+ chosen {
+ u-boot,dm-pre-reloc;
+ stdout-path = &uart1;
+ };
+
+ ahb {
+ usb1: ohci@00400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <&pioA 42 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci@00500000 {
+ status = "okay";
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_cmd_dat_default &pinctrl_sdmmc0_ck_cd_default>;
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_cmd_dat_default &pinctrl_sdmmc1_ck_cd_default>;
+ status = "okay"; /* conflict with qspi0 */
+ u-boot,dm-pre-reloc;
+ };
+
+ apb {
+ hlcdc: hlcdc@f0000000 {
+ atmel,vl-bpix = <4>;
+ atmel,guard-time = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_pwm &pinctrl_lcd_rgb666>;
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ display-timings {
+ u-boot,dm-pre-reloc;
+ 480x272 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ hback-porch = <2>;
+ vfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <11>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+ };
+
+ uart1: serial@f8020000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ pioA: gpio@fc038000 {
+ pinctrl {
+ pinctrl_lcd_base: pinctrl_lcd_base {
+ pinmux = <PIN_PC5__LCDVSYNC>,
+ <PIN_PC6__LCDHSYNC>,
+ <PIN_PC8__LCDDEN>,
+ <PIN_PC7__LCDPCK>;
+ bias-disable;
+ };
+
+ pinctrl_lcd_pwm: pinctrl_lcd_pwm {
+ pinmux = <PIN_PC3__LCDPWM>;
+ bias-disable;
+ };
+
+ pinctrl_lcd_rgb666: pinctrl_lcd_rgb666 {
+ pinmux = <PIN_PB13__LCDDAT2>,
+ <PIN_PB14__LCDDAT3>,
+ <PIN_PB15__LCDDAT4>,
+ <PIN_PB16__LCDDAT5>,
+ <PIN_PB17__LCDDAT6>,
+ <PIN_PB18__LCDDAT7>,
+ <PIN_PB21__LCDDAT10>,
+ <PIN_PB22__LCDDAT11>,
+ <PIN_PB23__LCDDAT12>,
+ <PIN_PB24__LCDDAT13>,
+ <PIN_PB25__LCDDAT14>,
+ <PIN_PB26__LCDDAT15>,
+ <PIN_PB29__LCDDAT18>,
+ <PIN_PB30__LCDDAT19>,
+ <PIN_PB31__LCDDAT20>,
+ <PIN_PC0__LCDDAT21>,
+ <PIN_PC1__LCDDAT22>,
+ <PIN_PC2__LCDDAT23>;
+ bias-disable;
+ };
+
+ pinctrl_sdmmc0_cmd_dat_default: sdmmc0_cmd_dat_default {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_sdmmc0_ck_cd_default: sdmmc0_ck_cd_default {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA10__SDMMC0_RSTN>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_sdmmc1_cmd_dat_default: sdmmc1_cmd_dat_default {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-pull-up;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_sdmmc1_ck_cd_default: sdmmc1_ck_cd_default {
+ pinmux = <PIN_PA22__SDMMC1_CK>,
+ <PIN_PA30__SDMMC1_CD>;
+ bias-disable;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_uart1_default: uart1_default {
+ pinmux = <PIN_PD2__URXD1>,
+ <PIN_PD3__UTXD1>;
+ bias-disable;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PB10__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PA31__GPIO>;
+ bias-disable;
+ };
+ };
+ };
+ };
+ };
+};
qspi0_clk: qspi0_clk@52 {
#clock-cells = <0>;
reg = <52>;
+ u-boot,dm-pre-reloc;
};
qspi1_clk: qspi1_clk@53 {
#clock-cells = <0>;
reg = <53>;
+ u-boot,dm-pre-reloc;
};
};
status = "disabled";
};
+ qspi1: spi@f0024000 {
+ compatible = "atmel,sama5d2-qspi";
+ reg = <0xf0024000 0x100>, <0xd8000000 0x08000000>;
+ reg-names = "qspi_base", "qspi_mmap";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&qspi1_clk>;
+ status = "disabled";
+ };
+
spi0: spi@f8000000 {
compatible = "atmel,at91rm9200-spi";
reg = <0xf8000000 0x100>;
status = "disabled";
};
+ uart3: serial@fc008000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xfc008000 0x100>;
+ clocks = <&uart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
i2c1: i2c@fc028000 {
compatible = "atmel,sama5d2-i2c";
reg = <0xfc028000 0x100>;
--- /dev/null
+/*
+ * sama5d27_som1.dtsi - Device Tree file for SAMA5D27 SOM1
+ *
+ * Copyright (C) 2017 Microchip Corporation
+ * Wenyou Yang <wenyou.yang@microchip.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+/ {
+ model = "Atmel SAMA5D27 SOM1 EK";
+ compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d2", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ aliases {
+ spi0 = &qspi1;
+ u-boot,dm-pre-reloc;
+ };
+
+ ahb {
+ apb {
+ qspi1: spi@f0024000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi1_sck_cs_default &pinctrl_qspi1_dat_default>;
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ spi_flash@0 {
+ compatible = "spi-flash";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+
+ macb0: ethernet@f8008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+ phy-mode = "rmii";
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ };
+
+ i2c0: i2c@f8028000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ status = "okay";
+
+ i2c_eeprom: i2c_eeprom@50 {
+ compatible = "microchip,24aa02e48";
+ reg = <0x50>;
+ };
+ };
+
+ i2c1: i2c@fc028000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+ };
+
+ pioA: gpio@fc038000 {
+ pinctrl {
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD4__TWD1>,
+ <PIN_PD5__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PD31__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_rmii: macb0_rmii {
+ pinmux = <PIN_PD9__GTXCK>,
+ <PIN_PD10__GTXEN>,
+ <PIN_PD11__GRXDV>,
+ <PIN_PD12__GRXER>,
+ <PIN_PD13__GRX0>,
+ <PIN_PD14__GRX1>,
+ <PIN_PD15__GTX0>,
+ <PIN_PD16__GTX1>,
+ <PIN_PD17__GMDC>,
+ <PIN_PD18__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_qspi1_sck_cs_default: qspi1_sck_cs_default {
+ pinmux = <PIN_PB5__QSPI1_SCK>,
+ <PIN_PB6__QSPI1_CS>;
+ bias-disable;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl_qspi1_dat_default: qspi1_dat_default {
+ pinmux = <PIN_PB7__QSPI1_IO0>,
+ <PIN_PB8__QSPI1_IO1>,
+ <PIN_PB9__QSPI1_IO2>,
+ <PIN_PB10__QSPI1_IO3>;
+ bias-pull-up;
+ u-boot,dm-pre-reloc;
+ };
+ };
+ };
+ };
+ };
+};
select SUPPORT_SPL
select BOARD_EARLY_INIT_F
+config TARGET_SAMA5D27_SOM1_EK
+ bool "SAMA5D27 SOM1 EK board"
+ select CPU_V7
+ select SUPPORT_SPL
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ help
+ The SAMA5D27 SOM1 embeds SAMA5D2 SiP(System in Package),
+ a 64Mbit QSPI flash, KSZ8081 Phy and a Mac-address EEPROM
+ 24AA02E48. The SAMA5D2 SiP integrates the ARM Cortex-A5
+ processor-based SAMA5D2 MPU with up to 1 Gbit DDR2-SDRAM
+ in a single package.
+
config TARGET_SAMA5D3_XPLAINED
bool "SAMA5D3 Xplained board"
select CPU_V7
source "board/atmel/at91sam9x5ek/Kconfig"
source "board/atmel/sama5d2_ptc/Kconfig"
source "board/atmel/sama5d2_xplained/Kconfig"
+source "board/atmel/sama5d27_som1_ek/Kconfig"
source "board/atmel/sama5d3_xplained/Kconfig"
source "board/atmel/sama5d3xek/Kconfig"
source "board/atmel/sama5d4_xplained/Kconfig"
--- /dev/null
+if TARGET_SAMA5D27_SOM1_EK
+
+config SYS_BOARD
+ default "sama5d27_som1_ek"
+
+config SYS_VENDOR
+ default "atmel"
+
+config SYS_SOC
+ default "at91"
+
+config SYS_CONFIG_NAME
+ default "sama5d27_som1_ek"
+
+endif
--- /dev/null
+SAMA5D27 SOM1 EK BOARD
+M: Wenyou Yang <wenyou.yang@microchip.com>
+S: Maintained
+F: board/atmel/sama5d27_som1_ek/
+F: include/configs/sama5d27_som1_ek.h
+F: configs/sama5d27_som1_ek_mmc_defconfig
--- /dev/null
+#
+# Copyright (C) 2017 Microchip Corporation
+# Wenyou Yang <wenyou.yang@microchip.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += sama5d27_som1_ek.o
--- /dev/null
+/*
+ * Copyright (C) 2017 Microchip Corporation
+ * Wenyou.Yang <wenyou.yang@microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <debug_uart.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/atmel_pio4.h>
+#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/atmel_sdhci.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sama5d2.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void board_usb_hw_init(void)
+{
+ atmel_pio4_set_pio_output(AT91_PIO_PORTB, 10, 1);
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_DM_VIDEO
+ at91_video_show_board_info();
+#endif
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+static void board_uart1_hw_init(void)
+{
+ atmel_pio4_set_a_periph(AT91_PIO_PORTD, 2, 1); /* URXD1 */
+ atmel_pio4_set_a_periph(AT91_PIO_PORTD, 3, 0); /* UTXD1 */
+
+ at91_periph_clk_enable(ATMEL_ID_UART1);
+}
+
+void board_debug_uart_init(void)
+{
+ board_uart1_hw_init();
+}
+#endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
+
+ return 0;
+}
+#endif
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_CMD_USB
+ board_usb_hw_init();
+#endif
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+#define MAC24AA_MAC_OFFSET 0xfa
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+#ifdef CONFIG_I2C_EEPROM
+ at91_set_ethaddr(MAC24AA_MAC_OFFSET);
+#endif
+ return 0;
+}
+#endif
+
+/* SPL */
+#ifdef CONFIG_SPL_BUILD
+void spl_board_init(void)
+{
+}
+
+static void ddrc_conf(struct atmel_mpddrc_config *ddrc)
+{
+ ddrc->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddrc->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_13 |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+ ATMEL_MPDDRC_CR_DIC_DS |
+ ATMEL_MPDDRC_CR_ZQ_LONG |
+ ATMEL_MPDDRC_CR_NB_8BANKS |
+ ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
+ ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
+
+ ddrc->rtr = 0x511;
+
+ ddrc->tpr0 = ((7 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET) |
+ (9 << ATMEL_MPDDRC_TPR0_TRC_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET) |
+ (2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET));
+
+ ddrc->tpr1 = ((22 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET) |
+ (23 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET) |
+ (200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR1_TXP_OFFSET));
+
+ ddrc->tpr2 = ((2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET) |
+ (8 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET) |
+ (8 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET));
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct atmel_mpddr *mpddrc = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
+ struct atmel_mpddrc_config ddrc_config;
+ u32 reg;
+
+ ddrc_conf(&ddrc_config);
+
+ at91_periph_clk_enable(ATMEL_ID_MPDDRC);
+ writel(AT91_PMC_DDR, &pmc->scer);
+
+ reg = readl(&mpddrc->io_calibr);
+ reg &= ~ATMEL_MPDDRC_IO_CALIBR_RDIV;
+ reg |= ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55;
+ reg &= ~ATMEL_MPDDRC_IO_CALIBR_TZQIO;
+ reg |= ATMEL_MPDDRC_IO_CALIBR_TZQIO_(101);
+ writel(reg, &mpddrc->io_calibr);
+
+ writel(ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_ONE_CYCLE,
+ &mpddrc->rd_data_path);
+
+ ddr3_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddrc_config);
+
+ writel(0x3, &mpddrc->cal_mr4);
+ writel(64, &mpddrc->tim_cal);
+}
+
+void at91_pmc_init(void)
+{
+ u32 tmp;
+
+ /*
+ * while coming from the ROM code, we run on PLLA @ 492 MHz / 164 MHz
+ * so we need to slow down and configure MCKR accordingly.
+ * This is why we have a special flavor of the switching function.
+ */
+ tmp = AT91_PMC_MCKR_PLLADIV_2 |
+ AT91_PMC_MCKR_MDIV_3 |
+ AT91_PMC_MCKR_CSS_MAIN;
+ at91_mck_init_down(tmp);
+
+ tmp = AT91_PMC_PLLAR_29 |
+ AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
+ AT91_PMC_PLLXR_MUL(40) |
+ AT91_PMC_PLLXR_DIV(1);
+ at91_plla_init(tmp);
+
+ tmp = AT91_PMC_MCKR_H32MXDIV |
+ AT91_PMC_MCKR_PLLADIV_2 |
+ AT91_PMC_MCKR_MDIV_3 |
+ AT91_PMC_MCKR_CSS_PLLA;
+ at91_mck_init(tmp);
+}
+#endif
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D27_SOM1_EK=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d27_som1_ek"
+CONFIG_DEBUG_UART=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
+CONFIG_SD_BOOT=y
+CONFIG_BOOTDELAY=3
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
+CONFIG_ENV_IS_IN_FAT=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_AT91_GENERIC_CLK=y
+CONFIG_DM_GPIO=y
+CONFIG_ATMEL_PIO4=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_AT91=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ATMEL=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_AT91PIO4=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xf8020000
+CONFIG_DEBUG_UART_CLOCK=82000000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_TIMER=y
+CONFIG_SPL_TIMER=y
+CONFIG_ATMEL_PIT_TIMER=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_ATMEL_USBA=y
+CONFIG_DM_VIDEO=y
+CONFIG_ATMEL_HLCD=y
--- /dev/null
+/*
+ * Configuration file for the SAMA5D27 SOM1 EK Board.
+ *
+ * Copyright (C) 2017 Microchip Corporation
+ * Wenyou Yang <wenyou.yang@microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "at91-sama5_common.h"
+
+#undef CONFIG_SYS_TEXT_BASE
+#undef CONFIG_SYS_AT91_MAIN_CLOCK
+#define CONFIG_SYS_TEXT_BASE 0x23f00000
+#define CONFIG_SYS_AT91_MAIN_CLOCK 24000000 /* from 24 MHz crystal */
+
+#define CONFIG_MISC_INIT_R
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0x20000000
+#define CONFIG_SYS_SDRAM_SIZE 0x8000000
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR 0x218000
+#else
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+/* NAND flash */
+#undef CONFIG_CMD_NAND
+
+/* SPI flash */
+#define CONFIG_SF_DEFAULT_SPEED 66000000
+
+#undef CONFIG_BOOTCOMMAND
+#ifdef CONFIG_SD_BOOT
+/* u-boot env in sd/mmc card */
+#define FAT_ENV_INTERFACE "mmc"
+#define FAT_ENV_DEVICE_AND_PART "0"
+#define FAT_ENV_FILE "uboot.env"
+#define CONFIG_ENV_SIZE 0x4000
+/* bootstrap + u-boot + env in sd card */
+#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d27_som1_ek.dtb; " \
+ "fatload mmc 0:1 0x22000000 zImage; " \
+ "bootz 0x22000000 - 0x21000000"
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait"
+#endif
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_ENV_OFFSET 0xb0000
+#define CONFIG_ENV_SIZE 0x10000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_BOOTCOMMAND "sf probe 0; " \
+ "sf read 0x21000000 0xc0000 0x20000; " \
+ "sf read 0x22000000 0xe0000 0x400000; " \
+ "bootz 0x22000000 - 0x21000000"
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait"
+#endif
+
+/* SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x200000
+#define CONFIG_SPL_MAX_SIZE 0x10000
+#define CONFIG_SPL_BSS_START_ADDR 0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+
+#define CONFIG_SYS_MONITOR_LEN (512 << 10)
+
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
+
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000
+#endif
+
+#endif
projects / u-boot.git / commitdiff
