dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
dtb-$(CONFIG_STM32MP13X) += \
- stm32mp135f-dhcor-dhsbc.dtb \
stm32mp135f-dk.dtb
dtb-$(CONFIG_STM32MP15X) += \
stm32mp157c-ed1-scmi.dtb \
stm32mp157c-ev1.dtb \
stm32mp157c-ev1-scmi.dtb \
- stm32mp157c-odyssey.dtb \
- stm32mp15xx-dhcom-drc02.dtb \
- stm32mp15xx-dhcom-pdk2.dtb \
- stm32mp15xx-dhcom-picoitx.dtb \
- stm32mp15xx-dhcor-avenger96.dtb \
- stm32mp15xx-dhcor-drc-compact.dtb \
- stm32mp15xx-dhcor-testbench.dtb
+ stm32mp157c-odyssey.dtb
dtb-$(CONFIG_STM32MP25X) += \
stm32mp257f-ev1.dtb
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) 2024 Marek Vasut <marex@denx.de>
- *
- * DHCOR STM32MP13 variant:
- * DHCR-STM32MP135F-C100-R051-EE-F0409-SPI4-RTC-WBT-I-01LG
- * DHCOR PCB number: 718-100 or newer
- * DHSBC PCB number: 719-100 or newer
- */
-
-/dts-v1/;
-
-#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
-#include "stm32mp135.dtsi"
-#include "stm32mp13xf.dtsi"
-#include "stm32mp13xx-dhcor-som.dtsi"
-
-/ {
- model = "DH electronics STM32MP135F DHCOR DHSBC";
- compatible = "dh,stm32mp135f-dhcor-dhsbc",
- "dh,stm32mp135f-dhcor-som",
- "st,stm32mp135";
-
- aliases {
- ethernet0 = ð1;
- ethernet1 = ð2;
- serial2 = &usart1;
- serial3 = &usart2;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&adc_1 {
- pinctrl-names = "default";
- pinctrl-0 = <&adc1_pins_a &adc1_usb_cc_pins_b>;
- vdda-supply = <&vdd_adc>;
- vref-supply = <&vdd_adc>;
- status = "okay";
-
- adc1: adc@0 {
- status = "okay";
-
- /*
- * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in2 & in11.
- * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
- * 5 * (5.1 + 47kOhms) * 5pF => 1.3us.
- * Use arbitrary margin here (e.g. 5us).
- *
- * The pinmux pins must be set as ANALOG, use datasheet
- * DS13483 Table 7. STM32MP135C/F ball definitions to
- * find out which 'pin name' maps to which 'additional
- * functions', which lists the mapping between pin and
- * ADC channel. In this case, PA5 maps to ADC1_INP2 and
- * PF13 maps to ADC1_INP11 .
- */
- channel@2 {
- reg = <2>;
- st,min-sample-time-ns = <5000>;
- };
-
- channel@11 {
- reg = <11>;
- st,min-sample-time-ns = <5000>;
- };
-
- /* Expansion connector: INP12:pin29 */
- channel@12 {
- reg = <12>;
- st,min-sample-time-ns = <5000>;
- };
- };
-};
-
-ð1 {
- status = "okay";
- pinctrl-0 = <ð1_rgmii_pins_a>;
- pinctrl-1 = <ð1_rgmii_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii-id";
- phy-handle = <ðphy1>;
- st,ext-phyclk;
- nvmem-cells = <ðernet_mac1_address>;
- nvmem-cell-names = "mac-address";
-
- mdio1 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
-
- ethphy1: ethernet-phy@1 {
- /* RTL8211F */
- compatible = "ethernet-phy-id001c.c916",
- "ethernet-phy-ieee802.3-c22";
- interrupt-parent = <&gpiog>;
- interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
- reg = <1>;
- reset-assert-us = <15000>;
- reset-deassert-us = <55000>;
- reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-ð2 {
- status = "okay";
- pinctrl-0 = <ð2_rgmii_pins_a>;
- pinctrl-1 = <ð2_rgmii_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii-id";
- phy-handle = <ðphy2>;
- st,ext-phyclk;
- nvmem-cells = <ðernet_mac2_address>;
- nvmem-cell-names = "mac-address";
-
- mdio1 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
-
- ethphy2: ethernet-phy@1 {
- /* RTL8211F */
- compatible = "ethernet-phy-id001c.c916",
- "ethernet-phy-ieee802.3-c22";
- interrupt-parent = <&gpiog>;
- interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
- reg = <1>;
- reset-assert-us = <15000>;
- reset-deassert-us = <55000>;
- reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&gpioa {
- gpio-line-names = "", "", "", "",
- "", "DHSBC_USB_PWR_CC1", "", "",
- "", "", "", "DHSBC_nETH1_RST",
- "", "DHCOR_HW-CODING_0", "", "";
-};
-
-&gpiob {
- gpio-line-names = "", "", "", "",
- "", "", "", "DHCOR_BT_HOST_WAKE",
- "", "", "", "",
- "", "DHSBC_nTPM_CS", "", "";
-};
-
-&gpioc {
- gpio-line-names = "", "", "", "DHSBC_USB_5V_MEAS",
- "", "", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiod {
- gpio-line-names = "", "", "", "",
- "", "DHCOR_RAM-CODING_0", "", "",
- "", "DHCOR_RAM-CODING_1", "", "",
- "", "", "", "";
-};
-
-&gpioe {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "", "DHSBC_nTPM_RST", "", "",
- "DHSBC_nTPM_PIRQ", "", "DHCOR_WL_HOST_WAKE", "";
-};
-
-&gpiof {
- gpio-line-names = "", "", "DHSBC_USB_PWR_nFLT", "",
- "", "", "", "",
- "", "", "", "",
- "DHCOR_WL_REG_ON", "DHSBC_USB_PWR_CC2", "", "";
-};
-
-&gpiog {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "DHSBC_nETH2_RST", "DHCOR_BT_DEV_WAKE", "", "",
- "DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB";
-};
-
-&gpioi {
- gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1",
- "DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT",
- "DHSBC_BOOT0", "DHSBC_BOOT1",
- "DHSBC_BOOT2", "DHSBC_USB-C_DATA_VBUS";
-};
-
-&i2c1 { /* Expansion connector: SDA:pin27 SCL:pin28 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c1_pins_a>;
- pinctrl-1 = <&i2c1_sleep_pins_a>;
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c5 { /* Expansion connector: SDA:pin3 SCL:pin5 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&i2c5_pins_b>;
- pinctrl-1 = <&i2c5_sleep_pins_b>;
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&m_can1 { /* Expansion connector: TX:pin16 RX:pin18 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can1_pins_a>;
- pinctrl-1 = <&m_can1_sleep_pins_a>;
- status = "okay";
-};
-
-&m_can2 { /* Expansion connector: TX:pin22 RX:pin26 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&m_can2_pins_a>;
- pinctrl-1 = <&m_can2_sleep_pins_a>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
- status = "okay";
-};
-
-&sai1 { /* Expansion connector: SCK-A:pin12 FS-A:pin35 SD-A:pin38 SD-B:pin40 */
- clocks = <&rcc SAI1>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- clock-names = "pclk", "x8k", "x11k";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai1a_pins_a &sai1b_pins_a>;
- pinctrl-1 = <&sai1a_sleep_pins_a &sai1b_sleep_pins_a>;
-};
-
-&scmi_voltd {
- status = "disabled";
-};
-
-&spi2 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&spi2_pins_a>;
- pinctrl-1 = <&spi2_sleep_pins_a>;
- cs-gpios = <&gpiob 13 0>;
- status = "okay";
-
- st33htph: tpm@0 {
- compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
- reg = <0>;
- spi-max-frequency = <24000000>;
- };
-};
-
-&spi3 { /* Expansion connector: MOSI:pin19 MISO:pin21 SCK:pin22 nCS:pin24 */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&spi3_pins_a>;
- pinctrl-1 = <&spi3_sleep_pins_a>;
- cs-gpios = <&gpiof 3 0>;
- status = "disabled";
-};
-
-&timers5 { /* Expansion connector: CH3:pin31 */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-
- pwm {
- pinctrl-0 = <&pwm5_pins_a>;
- pinctrl-1 = <&pwm5_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- status = "okay";
- };
- timer@4 {
- status = "okay";
- };
-};
-
-&timers13 { /* Expansion connector: CH1:pin32 */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-
- pwm {
- pinctrl-0 = <&pwm13_pins_a>;
- pinctrl-1 = <&pwm13_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- status = "okay";
- };
- timer@12 {
- status = "okay";
- };
-};
-
-&usart1 { /* Expansion connector: RX:pin33 TX:pin37 */
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&usart1_pins_b>;
- pinctrl-1 = <&usart1_sleep_pins_b>;
- pinctrl-2 = <&usart1_idle_pins_b>;
- status = "okay";
-};
-
-&usart2 { /* Expansion connector: RX:pin10 TX:pin8 RTS:pin11 CTS:pin36 */
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&usart2_pins_b>;
- pinctrl-1 = <&usart2_sleep_pins_b>;
- pinctrl-2 = <&usart2_idle_pins_b>;
- uart-has-rtscts;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbh_ohci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "peripheral";
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- usb33d-supply = <&usb33>;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
- st,current-boost-microamp = <1000>;
- st,decrease-hs-slew-rate;
- st,tune-hs-dc-level = <2>;
- st,enable-hs-rftime-reduction;
- st,trim-hs-current = <11>;
- st,trim-hs-impedance = <2>;
- st,tune-squelch-level = <1>;
- st,enable-hs-rx-gain-eq;
- st,no-hs-ftime-ctrl;
- st,no-lsfs-sc;
- connector {
- compatible = "usb-a-connector";
- vbus-supply = <&vbus_sw>;
- };
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
- st,current-boost-microamp = <1000>;
- st,decrease-hs-slew-rate;
- st,tune-hs-dc-level = <2>;
- st,enable-hs-rftime-reduction;
- st,trim-hs-current = <11>;
- st,trim-hs-impedance = <2>;
- st,tune-squelch-level = <1>;
- st,enable-hs-rx-gain-eq;
- st,no-hs-ftime-ctrl;
- st,no-lsfs-sc;
- connector {
- compatible = "gpio-usb-b-connector", "usb-b-connector";
- vbus-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>;
- label = "Type-C";
- self-powered;
- type = "micro";
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-/dts-v1/;
-
-#include "stm32mp151.dtsi"
-#include "stm32mp15xc.dtsi"
-#include "stm32mp15xx-dhcom-som.dtsi"
-#include "stm32mp15xx-dhcom-drc02.dtsi"
-
-/ {
- model = "DH Electronics STM32MP15xx DHCOM DRC02";
- compatible = "dh,stm32mp15xx-dhcom-drc02",
- "dh,stm32mp15xx-dhcom-som",
- "st,stm32mp1xx";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- aliases {
- serial0 = &uart4;
- serial1 = &usart3;
- serial2 = &uart8;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&adc {
- status = "disabled";
-};
-
-&dac {
- status = "disabled";
-};
-
-&gpiob {
- /*
- * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
- * GPIO line, however the STM32 UART driver assumes RX happens
- * during TX anyway and that it only controls drive enable DE
- * line. Hence, the RX is always enabled here.
- */
- rs485-rx-en-hog {
- gpio-hog;
- gpios = <8 0>;
- output-low;
- line-name = "rs485-rx-en";
- };
-};
-
-&gpiod {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-B", "",
- "", "", "", "DRC02-Out1",
- "DRC02-Out2", "", "", "";
-};
-
-&gpioi {
- gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I",
- "DHCOM-R", "DHCOM-M", "", "",
- "DRC02-In2", "", "", "",
- "", "", "", "";
-
- /*
- * NOTE: The USB Hub on the DRC02 needs a reset signal to be
- * pulled high in order to be detected by the USB Controller.
- * This signal should be handled by USB power sequencing in
- * order to reset the Hub when USB bus is powered down, but
- * so far there is no such functionality.
- */
- usb-hub-hog {
- gpio-hog;
- gpios = <2 0>;
- output-high;
- line-name = "usb-hub-reset";
- };
-};
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-
- eeprom@50 {
- compatible = "atmel,24c04";
- reg = <0x50>;
- pagesize = <16>;
- };
-};
-
-&i2c4 {
- touchscreen@49 {
- status = "disabled";
- };
-};
-
-&i2c5 { /* TP7/TP8 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&sdmmc3 {
- /*
- * On DRC02, the SoM does not have SDIO WiFi. The pins
- * are used for on-board microSD slot instead.
- */
- /delete-property/broken-cd;
- cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
- disable-wp;
-};
-
-&spi1 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins_a>;
- cs-gpios = <&gpioz 3 0>;
- /* Use PIO for the display */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "disabled"; /* Enable once there is display driver */
- /*
- * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
- * also connected to the display board connector.
- */
-};
-
-&usart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&usart3_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-/*
- * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
- * however the STM32MP1 pinmux cannot map them to UART4 .
- */
-
-&uart8 { /* RS485 */
- linux,rs485-enabled-at-boot-time;
- pinctrl-names = "default";
- pinctrl-0 = <&uart8_pins_a>;
- rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2019 Marek Vasut <marex@denx.de>
- */
-/dts-v1/;
-
-#include "stm32mp151.dtsi"
-#include "stm32mp15xc.dtsi"
-#include "stm32mp15xx-dhcom-som.dtsi"
-#include "stm32mp15xx-dhcom-pdk2.dtsi"
-
-/ {
- model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)";
- compatible = "dh,stm32mp15xx-dhcom-pdk2",
- "dh,stm32mp15xx-dhcom-som",
- "st,stm32mp15x";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
- */
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- aliases {
- serial0 = &uart4;
- serial1 = &usart3;
- serial2 = &uart8;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- clk_ext_audio_codec: clock-codec {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- };
-
- display_bl: display-bl {
- compatible = "pwm-backlight";
- pwms = <&pwm2 3 500000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
- default-brightness-level = <8>;
- enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
- power-supply = <®_panel_bl>;
- status = "okay";
- };
-
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- poll-interval = <20>;
-
- /*
- * The EXTi IRQ line 3 is shared with ethernet,
- * so mark this as polled GPIO key.
- */
- button-0 {
- label = "TA1-GPIO-A";
- linux,code = <KEY_A>;
- gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
- };
-
- /*
- * The EXTi IRQ line 6 is shared with touchscreen,
- * so mark this as polled GPIO key.
- */
- button-1 {
- label = "TA2-GPIO-B";
- linux,code = <KEY_B>;
- gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
- };
-
- /*
- * The EXTi IRQ line 0 is shared with PMIC,
- * so mark this as polled GPIO key.
- */
- button-2 {
- label = "TA3-GPIO-C";
- linux,code = <KEY_C>;
- gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- button-3 {
- label = "TA4-GPIO-D";
- linux,code = <KEY_D>;
- gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
- wakeup-source;
- };
- };
-
- led {
- compatible = "gpio-leds";
-
- led-0 {
- label = "green:led5";
- gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- status = "disabled";
- };
-
- led-1 {
- label = "green:led6";
- gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-2 {
- label = "green:led7";
- gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- led-3 {
- label = "green:led8";
- gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- panel {
- compatible = "edt,etm0700g0edh6";
- backlight = <&display_bl>;
- power-supply = <®_panel_bl>;
-
- port {
- lcd_panel_in: endpoint {
- remote-endpoint = <&lcd_display_out>;
- };
- };
- };
-
- reg_panel_bl: regulator-panel-bl {
- compatible = "regulator-fixed";
- regulator-name = "panel_backlight";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <®_panel_supply>;
- };
-
- reg_panel_supply: regulator-panel-supply {
- compatible = "regulator-fixed";
- regulator-name = "panel_supply";
- regulator-min-microvolt = <24000000>;
- regulator-max-microvolt = <24000000>;
- };
-
- sound {
- compatible = "audio-graph-card";
- routing =
- "MIC_IN", "Capture",
- "Capture", "Mic Bias",
- "Playback", "HP_OUT";
- dais = <&sai2a_port &sai2b_port>;
- status = "okay";
- };
-};
-
-&cec {
- pinctrl-names = "default";
- pinctrl-0 = <&cec_pins_a>;
- status = "okay";
-};
-
-&i2c2 { /* Header X22 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&i2c5 { /* Header X21 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- clocks = <&clk_ext_audio_codec>;
- VDDA-supply = <&v3v3>;
- VDDIO-supply = <&vdd>;
-
- sgtl5000_port: port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- sgtl5000_tx_endpoint: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&sai2a_endpoint>;
- frame-master = <&sgtl5000_tx_endpoint>;
- bitclock-master = <&sgtl5000_tx_endpoint>;
- };
-
- sgtl5000_rx_endpoint: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&sai2b_endpoint>;
- frame-master = <&sgtl5000_rx_endpoint>;
- bitclock-master = <&sgtl5000_rx_endpoint>;
- };
- };
-
- };
-
- touchscreen@38 {
- compatible = "edt,edt-ft5406";
- reg = <0x38>;
- interrupt-parent = <&gpioc>;
- interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
- };
-};
-
-<dc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <<dc_pins_b>;
- pinctrl-1 = <<dc_sleep_pins_b>;
- status = "okay";
-
- port {
- lcd_display_out: endpoint {
- remote-endpoint = <&lcd_panel_in>;
- };
- };
-};
-
-&sai2 {
- clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- clock-names = "pclk", "x8k", "x11k";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
- pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
- status = "okay";
-
- sai2a: audio-controller@4400b004 {
- #clock-cells = <0>;
- dma-names = "tx";
- clocks = <&rcc SAI2_K>;
- clock-names = "sai_ck";
- status = "okay";
-
- sai2a_port: port {
- sai2a_endpoint: endpoint {
- remote-endpoint = <&sgtl5000_tx_endpoint>;
- format = "i2s";
- mclk-fs = <512>;
- dai-tdm-slot-num = <2>;
- dai-tdm-slot-width = <16>;
- };
- };
- };
-
- sai2b: audio-controller@4400b024 {
- dma-names = "rx";
- st,sync = <&sai2a 2>;
- clocks = <&rcc SAI2_K>, <&sai2a>;
- clock-names = "sai_ck", "MCLK";
- status = "okay";
-
- sai2b_port: port {
- sai2b_endpoint: endpoint {
- remote-endpoint = <&sgtl5000_rx_endpoint>;
- format = "i2s";
- mclk-fs = <512>;
- dai-tdm-slot-num = <2>;
- dai-tdm-slot-width = <16>;
- };
- };
- };
-};
-
-&timers2 {
- /* spare dmas for other usage (un-delete to enable pwm capture) */
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
- pwm2: pwm {
- pinctrl-0 = <&pwm2_pins_a>;
- pinctrl-names = "default";
- status = "okay";
- };
- timer@1 {
- status = "okay";
- };
-};
-
-&usart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&usart3_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart8 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
- uart-has-rtscts;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "otg";
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- vbus-supply = <&vbus_otg>;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-/dts-v1/;
-
-#include "stm32mp157.dtsi"
-#include "stm32mp15xc.dtsi"
-#include "stm32mp15xx-dhcom-som.dtsi"
-#include "stm32mp15xx-dhcom-picoitx.dtsi"
-
-/ {
- model = "DH Electronics STM32MP15xx DHCOM PicoITX";
- compatible = "dh,stm32mp15xx-dhcom-picoitx",
- "dh,stm32mp15xx-dhcom-som",
- "st,stm32mp1xx";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- aliases {
- serial0 = &uart4;
- serial1 = &usart3;
- serial2 = &uart8;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- led {
- compatible = "gpio-leds";
-
- led-0 {
- label = "yellow:led";
- gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-};
-
-&adc {
- status = "disabled";
-};
-
-&dac {
- status = "disabled";
-};
-
-&fmc {
- status = "disabled";
-};
-
-&gpioa {
- /*
- * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
- * port power. This signal should be handled by USB power sequencing
- * in order to turn on port power when USB bus is powered up, but so
- * far there is no such functionality.
- */
- usb-port-power-hog {
- gpio-hog;
- gpios = <13 0>;
- output-low;
- line-name = "usb-port-power";
- };
-};
-
-&gpioc {
- gpio-line-names = "", "", "", "",
- "", "", "PicoITX-In1", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiod {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-B", "",
- "", "", "", "PicoITX-Out1",
- "PicoITX-Out2", "", "", "";
-};
-
-&gpiog {
- gpio-line-names = "PicoITX-In2", "", "", "",
- "", "", "", "",
- "DHCOM-L", "", "", "",
- "", "", "", "";
-};
-
-&i2c2 { /* On board-to-board connector (optional) */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c5 { /* On board-to-board connector */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&ksz8851 {
- status = "disabled";
-};
-
-&usart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&usart3_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart8 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbh_ohci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "otg";
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- vbus-supply = <&vbus_otg>;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
- */
-
-#include "stm32mp15-pinctrl.dtsi"
-#include "stm32mp15xxaa-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
- aliases {
- ethernet0 = ðernet0;
- ethernet1 = &ksz8851;
- rtc0 = &hwrtc;
- rtc1 = &rtc;
- };
-
- memory@c0000000 {
- device_type = "memory";
- reg = <0xC0000000 0x40000000>;
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- mcuram2: mcuram2@10000000 {
- compatible = "shared-dma-pool";
- reg = <0x10000000 0x40000>;
- no-map;
- };
-
- vdev0vring0: vdev0vring0@10040000 {
- compatible = "shared-dma-pool";
- reg = <0x10040000 0x1000>;
- no-map;
- };
-
- vdev0vring1: vdev0vring1@10041000 {
- compatible = "shared-dma-pool";
- reg = <0x10041000 0x1000>;
- no-map;
- };
-
- vdev0buffer: vdev0buffer@10042000 {
- compatible = "shared-dma-pool";
- reg = <0x10042000 0x4000>;
- no-map;
- };
-
- mcuram: mcuram@30000000 {
- compatible = "shared-dma-pool";
- reg = <0x30000000 0x40000>;
- no-map;
- };
-
- retram: retram@38000000 {
- compatible = "shared-dma-pool";
- reg = <0x38000000 0x10000>;
- no-map;
- };
- };
-
- ethernet_vio: vioregulator {
- compatible = "regulator-fixed";
- regulator-name = "vio";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-};
-
-&adc {
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,min-sample-time-nsecs = <5000>;
- st,adc-channels = <0>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <1>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-&crc1 {
- status = "okay";
-};
-
-&dac {
- pinctrl-names = "default";
- pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
- vref-supply = <&vdda>;
- status = "okay";
-
- dac1: dac@1 {
- status = "okay";
- };
- dac2: dac@2 {
- status = "okay";
- };
-};
-
-&dts {
- status = "okay";
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rmii_pins_c &mco2_pins_a>;
- pinctrl-1 = <ðernet0_rmii_sleep_pins_c &mco2_sleep_pins_a>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rmii";
- max-speed = <100>;
- phy-handle = <&phy0>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
-
- phy0: ethernet-phy@1 {
- reg = <1>;
- /* LAN8710Ai */
- compatible = "ethernet-phy-id0007.c0f0",
- "ethernet-phy-ieee802.3-c22";
- clocks = <&rcc CK_MCO2>;
- reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
- reset-assert-us = <500>;
- reset-deassert-us = <500>;
- smsc,disable-energy-detect;
- interrupt-parent = <&gpioi>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&fmc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&fmc_pins_b>;
- pinctrl-1 = <&fmc_sleep_pins_b>;
- status = "okay";
-
- ksz8851: ethernet@1,0 {
- compatible = "micrel,ks8851-mll";
- reg = <1 0x0 0x2>, <1 0x2 0x20000>;
- interrupt-parent = <&gpioc>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- bank-width = <2>;
-
- /* Timing values are in nS */
- st,fmc2-ebi-cs-mux-enable;
- st,fmc2-ebi-cs-transaction-type = <4>;
- st,fmc2-ebi-cs-buswidth = <16>;
- st,fmc2-ebi-cs-address-setup-ns = <5>;
- st,fmc2-ebi-cs-address-hold-ns = <5>;
- st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
- st,fmc2-ebi-cs-data-setup-ns = <45>;
- st,fmc2-ebi-cs-data-hold-ns = <1>;
- st,fmc2-ebi-cs-write-address-setup-ns = <5>;
- st,fmc2-ebi-cs-write-address-hold-ns = <5>;
- st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
- st,fmc2-ebi-cs-write-data-setup-ns = <45>;
- st,fmc2-ebi-cs-write-data-hold-ns = <1>;
- };
-};
-
-&gpioa {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-K", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiob {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "DHCOM-Q", "", "", "",
- "", "", "", "";
-};
-
-&gpioc {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-E", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiod {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-B", "",
- "", "", "", "DHCOM-F",
- "DHCOM-D", "", "", "";
-};
-
-&gpioe {
- gpio-line-names = "", "", "", "",
- "", "", "DHCOM-P", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiof {
- gpio-line-names = "", "", "", "DHCOM-A",
- "", "", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiog {
- gpio-line-names = "DHCOM-C", "", "", "",
- "", "", "", "",
- "DHCOM-L", "", "", "",
- "", "", "", "";
-};
-
-&gpioh {
- gpio-line-names = "", "", "", "",
- "", "", "", "DHCOM-N",
- "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U",
- "DHCOM-T", "", "DHCOM-S", "";
-};
-
-&gpioi {
- gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I",
- "DHCOM-R", "DHCOM-M", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-
- hwrtc: rtc@32 {
- compatible = "microcrystal,rv8803";
- reg = <0x32>;
- };
-
- pmic: stpmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- regulators {
- compatible = "st,stpmic1-regulators";
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- st,mask-reset;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-always-on;
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- interrupts = <IT_CURLIM_LDO4 0>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
- interrupt-names = "onkey-falling", "onkey-rising";
- power-off-time-sec = <10>;
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- touchscreen@49 {
- compatible = "ti,tsc2004";
- reg = <0x49>;
- vio-supply = <&v3v3>;
- interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
-};
-
-&ipcc {
- status = "okay";
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&m4_rproc {
- memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
- <&vdev0vring1>, <&vdev0buffer>;
- mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
- mbox-names = "vq0", "vq1", "shutdown";
- interrupt-parent = <&exti>;
- interrupts = <68 1>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a
- &qspi_bk1_pins_a
- &qspi_cs1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a
- &qspi_bk1_sleep_pins_a
- &qspi_cs1_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rcc {
- /* Connect MCO2 output to ETH_RX_CLK input via pad-pad connection */
- clocks = <&rcc CK_MCO2>;
- clock-names = "ETH_RX_CLK/ETH_REF_CLK";
-
- /*
- * Set PLL4P output to 100 MHz to supply SDMMC with faster clock,
- * set MCO2 output to 50 MHz to supply ETHRX clock with PLL4P/2,
- * so that MCO2 behaves as a divider for the ETHRX clock here.
- */
- assigned-clocks = <&rcc CK_MCO2>, <&rcc PLL4_P>;
- assigned-clock-parents = <&rcc PLL4_P>;
- assigned-clock-rates = <50000000>, <100000000>;
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep", "init";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
- pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>;
- cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- st,cmd-gpios = <&gpiod 2 0>;
- st,ck-gpios = <&gpioc 12 0>;
- st,ckin-gpios = <&gpioe 4 0>;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- status = "okay";
-};
-
-&sdmmc1_b4_pins_a {
- /*
- * SD bus pull-up resistors:
- * - optional on SoMs with SD voltage translator
- * - mandatory on SoMs without SD voltage translator
- */
- pins1 {
- bias-pull-up;
- };
- pins2 {
- bias-pull-up;
- };
-};
-
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
- non-removable;
- no-sd;
- no-sdio;
- st,neg-edge;
- bus-width = <8>;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&sdmmc3 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc3_b4_pins_a>;
- pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
- pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
- broken-cd;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-
-#include "stm32mp151.dtsi"
-#include "stm32mp15xc.dtsi"
-#include "stm32mp15xx-dhcor-som.dtsi"
-#include "stm32mp15xx-dhcor-avenger96.dtsi"
-
-/ {
- model = "Arrow Electronics STM32MP15xx Avenger96 board";
- compatible = "arrow,stm32mp15xx-avenger96",
- "dh,stm32mp15xx-dhcor-som",
- "st,stm32mp15x";
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
-#include "stm32mp15xx-dhcor-io1v8.dtsi"
-
-/ {
- aliases {
- ethernet0 = ðernet0;
- mmc0 = &sdmmc1;
- serial0 = &uart4;
- serial1 = &uart7;
- serial2 = &usart2;
- spi0 = &qspi;
- };
-
- /* XTal Q1 */
- cec_clock: clk-cec-fixed {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con: endpoint {
- remote-endpoint = <&adv7513_out>;
- };
- };
- };
-
- led {
- compatible = "gpio-leds";
- led1 {
- label = "green:user0";
- gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led2 {
- label = "green:user1";
- gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led3 {
- label = "green:user2";
- gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- led4 {
- label = "green:user3";
- gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- panic-indicator;
- };
- };
-
- sd_switch: regulator-sd_switch {
- compatible = "regulator-gpio";
- regulator-name = "sd_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
- regulator-type = "voltage";
- regulator-always-on;
-
- gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1>,
- <2900000 0x0>;
- };
-
- sound {
- compatible = "audio-graph-card";
- label = "STM32MP1-AV96-HDMI";
- dais = <&sai2a_port>;
- status = "okay";
- };
-
- wlan_pwr: regulator-wlan {
- compatible = "regulator-fixed";
-
- regulator-name = "wl-reg";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-};
-
-&adc {
- pinctrl-names = "default";
- pinctrl-0 = <&adc12_ain_pins_b>;
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,adc-channels = <0 1 6>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <0 1 2>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_c>;
- pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
- reset-delay-us = <1000>;
-
- phy0: ethernet-phy@7 {
- reg = <7>;
-
- rxc-skew-ps = <1500>;
- rxdv-skew-ps = <540>;
- rxd0-skew-ps = <420>;
- rxd1-skew-ps = <420>;
- rxd2-skew-ps = <420>;
- rxd3-skew-ps = <420>;
-
- txc-skew-ps = <1440>;
- txen-skew-ps = <540>;
- txd0-skew-ps = <420>;
- txd1-skew-ps = <420>;
- txd2-skew-ps = <420>;
- txd3-skew-ps = <420>;
- };
- };
-};
-
-&gpioa {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "", "", "", "AV96-K",
- "AV96-I", "", "AV96-A", "";
-};
-
-&gpiob {
- gpio-line-names = "", "", "", "",
- "", "AV96-J", "", "",
- "", "", "", "AV96-B",
- "", "AV96-L", "", "";
-};
-
-&gpioc {
- gpio-line-names = "", "", "", "AV96-C",
- "", "", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiod {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "AV96-D", "", "", "",
- "", "", "AV96-E", "AV96-F";
-};
-
-&gpiof {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "", "", "", "",
- "AV96-G", "AV96-H", "", "";
-};
-
-&i2c1 { /* X6 I2C1 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_b>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c2 { /* X6 I2C2 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_c>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c4 {
- hdmi-transmitter@3d {
- compatible = "adi,adv7513";
- reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
- reg-names = "main", "edid", "cec", "packet";
- clocks = <&cec_clock>;
- clock-names = "cec";
-
- avdd-supply = <&v3v3>;
- dvdd-supply = <&v3v3>;
- pvdd-supply = <&v3v3>;
- dvdd-3v-supply = <&v3v3>;
- bgvdd-supply = <&v3v3>;
-
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
- interrupt-parent = <&gpiog>;
-
- status = "okay";
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7513_in: endpoint {
- remote-endpoint = <<dc_ep0_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7513_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
-
- port@2 {
- reg = <2>;
- adv7513_i2s0: endpoint {
- remote-endpoint = <&sai2a_endpoint>;
- };
- };
- };
- };
-};
-
-<dc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <<dc_pins_d>;
- pinctrl-1 = <<dc_sleep_pins_d>;
- status = "okay";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ltdc_ep0_out: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&adv7513_in>;
- };
- };
-};
-
-&sai2 {
- clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sai2a_pins_c>;
- pinctrl-1 = <&sai2a_sleep_pins_c>;
- clock-names = "pclk", "x8k", "x11k";
- status = "okay";
-
- sai2a: audio-controller@4400b004 {
- #clock-cells = <0>;
- dma-names = "tx";
- clocks = <&rcc SAI2_K>;
- clock-names = "sai_ck";
- status = "okay";
-
- sai2a_port: port {
- sai2a_endpoint: endpoint {
- remote-endpoint = <&adv7513_i2s0>;
- format = "i2s";
- mclk-fs = <256>;
- };
- };
- };
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
- cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- vqmmc-supply = <&sd_switch>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
- bus-width = <8>;
- mmc-ddr-1_8v;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&vdd_io>;
- status = "okay";
-};
-
-&sdmmc3 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc3_b4_pins_b>;
- pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
- pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
- broken-cd;
- non-removable;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&wlan_pwr>;
- status = "okay";
-
- #address-cells = <1>;
- #size-cells = <0>;
- brcmf: bcrmf@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-&spi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- cs-gpios = <&gpioi 0 0>;
- status = "disabled";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&uart4 {
- /* On Low speed expansion header */
- label = "LS-UART1";
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart7 {
- /* On Low speed expansion header */
- label = "LS-UART0";
- pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
- uart-has-rtscts;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-/* Bluetooth */
-&usart2 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&usart2_pins_a>;
- pinctrl-1 = <&usart2_sleep_pins_a>;
- st,hw-flow-ctrl;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
- shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- phy-names = "usb";
- status = "okay";
-};
-
-&usbotg_hs {
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- status = "okay";
- vbus-supply = <&vbus_otg>;
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) 2022 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-
-#include "stm32mp151.dtsi"
-#include "stm32mp15xc.dtsi"
-#include "stm32mp15xx-dhcor-som.dtsi"
-#include "stm32mp15xx-dhcor-drc-compact.dtsi"
-
-/ {
- model = "DH electronics STM32MP15xx DHCOR DRC Compact";
- compatible = "dh,stm32mp15xx-dhcor-drc-compact",
- "dh,stm32mp15xx-dhcor-som",
- "st,stm32mp1xx";
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) 2022 Marek Vasut <marex@denx.de>
- */
-
-/ {
- aliases {
- ethernet0 = ðernet0;
- ethernet1 = &ksz8851;
- mmc0 = &sdmmc1;
- rtc0 = &hwrtc;
- rtc1 = &rtc;
- serial0 = &uart4;
- serial1 = &uart8;
- serial2 = &usart3;
- serial3 = &uart5;
- spi0 = &qspi;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- led {
- compatible = "gpio-leds";
- led1 {
- label = "yellow:user0";
- gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
-
- led2 {
- label = "red:user1";
- gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
- };
-
- ethernet_vio: vioregulator {
- compatible = "regulator-fixed";
- regulator-name = "vio";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-};
-
-&adc { /* X11 ADC inputs */
- pinctrl-names = "default";
- pinctrl-0 = <&adc12_ain_pins_b>;
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,adc-channels = <0 1 6>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <0 1 2>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_c>;
- pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
- reset-delay-us = <1000>;
- reset-post-delay-us = <1000>;
-
- phy0: ethernet-phy@7 {
- reg = <7>;
-
- rxc-skew-ps = <1500>;
- rxdv-skew-ps = <540>;
- rxd0-skew-ps = <420>;
- rxd1-skew-ps = <420>;
- rxd2-skew-ps = <420>;
- rxd3-skew-ps = <420>;
-
- txc-skew-ps = <1440>;
- txen-skew-ps = <540>;
- txd0-skew-ps = <420>;
- txd1-skew-ps = <420>;
- txd2-skew-ps = <420>;
- txd3-skew-ps = <420>;
- };
- };
-};
-
-&fmc {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&fmc_pins_b>;
- pinctrl-1 = <&fmc_sleep_pins_b>;
- status = "okay";
-
- ksz8851: ethernet@1,0 {
- compatible = "micrel,ks8851-mll";
- reg = <1 0x0 0x2>, <1 0x2 0x20000>;
- interrupt-parent = <&gpioc>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- bank-width = <2>;
-
- /* Timing values are in nS */
- st,fmc2-ebi-cs-mux-enable;
- st,fmc2-ebi-cs-transaction-type = <4>;
- st,fmc2-ebi-cs-buswidth = <16>;
- st,fmc2-ebi-cs-address-setup-ns = <5>;
- st,fmc2-ebi-cs-address-hold-ns = <5>;
- st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
- st,fmc2-ebi-cs-data-setup-ns = <45>;
- st,fmc2-ebi-cs-data-hold-ns = <1>;
- st,fmc2-ebi-cs-write-address-setup-ns = <5>;
- st,fmc2-ebi-cs-write-address-hold-ns = <5>;
- st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
- st,fmc2-ebi-cs-write-data-setup-ns = <45>;
- st,fmc2-ebi-cs-write-data-hold-ns = <1>;
- };
-};
-
-&gpioa {
- gpio-line-names = "", "", "", "",
- "DRCC-VAR2", "", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpioe {
- gpio-line-names = "", "", "", "",
- "", "DRCC-GPIO0", "", "",
- "", "", "", "",
- "", "", "", "";
-};
-
-&gpiog {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "", "", "", "",
- "DRCC-GPIO5", "", "", "";
-};
-
-&gpioh {
- gpio-line-names = "", "", "", "DRCC-HW2",
- "DRCC-GPIO4", "", "", "",
- "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
- "DRCC-VAR0", "", "", "DRCC-GPIO6";
-};
-
-&gpioi {
- gpio-line-names = "", "", "", "",
- "", "", "", "DRCC-GPIO2",
- "", "DRCC-GPIO1", "", "",
- "", "", "", "";
-};
-
-&i2c1 { /* X11 I2C1 */
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_b>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c4 {
- hwrtc: rtc@32 {
- compatible = "microcrystal,rv8803";
- reg = <0x32>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c04";
- reg = <0x50>;
- pagesize = <16>;
- };
-};
-
-&sdmmc1 { /* MicroSD */
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
- cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- disable-wp;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&vdd>;
- vqmmc-supply = <&vdd>;
- status = "okay";
-};
-
-&sdmmc2 { /* eMMC */
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
- bus-width = <8>;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&vdd>;
- status = "okay";
-};
-
-&sdmmc3 { /* SDIO Wi-Fi */
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc3_b4_pins_a>;
- pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
- pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
- broken-cd;
- bus-width = <4>;
- mmc-ddr-3_3v;
- st,neg-edge;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- status = "okay";
-};
-
-&spi2 { /* X11 SPI */
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_b>;
- cs-gpios = <&gpioi 0 0>;
- status = "disabled";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&uart4 {
- label = "UART0";
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_d>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart5 { /* X11 UART */
- label = "X11-UART5";
- pinctrl-names = "default";
- pinctrl-0 = <&uart5_pins_a>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart8 {
- label = "RS485-1";
- pinctrl-names = "default";
- pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
- uart-has-rtscts;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usart3 { /* RS485 or RS232 */
- label = "RS485-2";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&usart3_pins_e>;
- pinctrl-1 = <&usart3_sleep_pins_e>;
- uart-has-rtscts;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbh_ohci {
- phys = <&usbphyc_port0>;
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "otg";
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- vbus-supply = <&vbus_otg>;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
- connector {
- compatible = "usb-a-connector";
- vbus-supply = <&vbus_sw>;
- };
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-/ {
- /* Enpirion EP3A8LQI U2 on the DHCOR */
- vdd_io: regulator-buck-io {
- compatible = "regulator-fixed";
- regulator-name = "buck-io";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-};
-
-&vdd {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd_io>;
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- * Copyright (C) 2020 Marek Vasut <marex@denx.de>
- */
-
-#include "stm32mp15-pinctrl.dtsi"
-#include "stm32mp15xxac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
- aliases {
- spi0 = &qspi;
- };
-
- memory@c0000000 {
- device_type = "memory";
- reg = <0xc0000000 0x40000000>;
- };
-};
-
-&crc1 {
- status = "okay";
-};
-
-&dts {
- status = "okay";
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-
- pmic: stpmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- interrupts = <IT_CURLIM_LDO4 0>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- regulator-enable-ramp-delay = <300000>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- regulator-active-discharge = <1>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- eeprom@53 {
- compatible = "atmel,24c02";
- reg = <0x53>;
- pagesize = <16>;
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a
- &qspi_bk1_pins_a
- &qspi_cs1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a
- &qspi_bk1_sleep_pins_a
- &qspi_cs1_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <50000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) 2022 Marek Vasut <marex@denx.de>
- */
-/dts-v1/;
-
-#include "stm32mp151.dtsi"
-#include "stm32mp15xx-dhcor-som.dtsi"
-
-/ {
- model = "DH electronics STM32MP15xx DHCOR Testbench";
- compatible = "dh,stm32mp15xx-dhcor-testbench",
- "dh,stm32mp15xx-dhcor-som",
- "st,stm32mp1xx";
-
- aliases {
- ethernet0 = ðernet0;
- mmc0 = &sdmmc1;
- mmc1 = &sdmmc2;
- serial0 = &uart4;
- serial1 = &uart7;
- spi0 = &qspi;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- sd_switch: regulator-sd_switch {
- compatible = "regulator-gpio";
- regulator-name = "sd_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
- regulator-type = "voltage";
- regulator-always-on;
-
- gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1>,
- <2900000 0x0>;
- };
-};
-
-&adc {
- pinctrl-names = "default";
- pinctrl-0 = <&adc12_ain_pins_b>;
- vdd-supply = <&vdd>;
- vdda-supply = <&vdda>;
- vref-supply = <&vdda>;
- status = "okay";
-
- adc1: adc@0 {
- st,adc-channels = <0 1 6>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-
- adc2: adc@100 {
- st,adc-channels = <0 1 2>;
- st,min-sample-time-nsecs = <5000>;
- status = "okay";
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_c>;
- pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
- reset-delay-us = <1000>;
-
- phy0: ethernet-phy@7 {
- reg = <7>;
-
- rxc-skew-ps = <1500>;
- rxdv-skew-ps = <540>;
- rxd0-skew-ps = <420>;
- rxd1-skew-ps = <420>;
- rxd2-skew-ps = <420>;
- rxd3-skew-ps = <420>;
-
- txc-skew-ps = <1440>;
- txen-skew-ps = <540>;
- txd0-skew-ps = <420>;
- txd1-skew-ps = <420>;
- txd2-skew-ps = <420>;
- txd3-skew-ps = <420>;
- };
- };
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
- cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- vqmmc-supply = <&sd_switch>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
- bus-width = <8>;
- mmc-ddr-1_8v;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&uart7 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
- uart-has-rtscts;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- phy-names = "usb";
- status = "okay";
-};
-
-&usbotg_hs {
- pinctrl-0 = <&usbotg_hs_pins_a>;
- pinctrl-names = "default";
- phy-names = "usb2-phy";
- phys = <&usbphyc_port1 0>;
- status = "okay";
- vbus-supply = <&vbus_otg>;
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
-
-&vdd {
- /delete-property/ regulator-always-on;
- regulator-min-microvolt = <1200000>;
-};
fdt-1 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp157c-dhcom-pdk2.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
fdt-2 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcom-drc02.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp153c-dhcom-drc02.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
fdt-3 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp157c-dhcom-picoitx.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
config-1 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-pdk2_somrev0_boardrev0";
+ description = "dh,stm32mp157c-dhcom-pdk2_somrev0_boardrev0";
firmware = "uboot";
fdt = "fdt-1";
};
config-2 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-pdk2_somrev1_boardrev0";
+ description = "dh,stm32mp157c-dhcom-pdk2_somrev1_boardrev0";
firmware = "uboot";
fdt = "fdt-1";
};
config-3 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-drc02_somrev0_boardrev0";
+ description = "dh,stm32mp153c-dhcom-drc02_somrev0_boardrev0";
firmware = "uboot";
fdt = "fdt-2";
};
config-4 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-drc02_somrev1_boardrev0";
+ description = "dh,stm32mp153c-dhcom-drc02_somrev1_boardrev0";
firmware = "uboot";
fdt = "fdt-2";
};
config-5 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-picoitx_somrev0_boardrev0";
+ description = "dh,stm32mp157c-dhcom-picoitx_somrev0_boardrev0";
loadables = "uboot";
fdt = "fdt-3";
};
config-6 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcom-picoitx_somrev1_boardrev0";
+ description = "dh,stm32mp157c-dhcom-picoitx_somrev1_boardrev0";
loadables = "uboot";
fdt = "fdt-3";
};
fdt-1 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcor-testbench.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp151a-dhcor-testbench.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
fdt-2 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp157a-dhcor-avenger96.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
fdt-3 {
description = ".dtb";
- data = /incbin/("arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtb");
+ data = /incbin/("dts/upstream/src/arm/st/stm32mp153c-dhcor-drc-compact.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
config-1 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcor-testbench_somrev0_boardrev1";
+ description = "dh,stm32mp151a-dhcor-testbench_somrev0_boardrev1";
firmware = "uboot";
fdt = "fdt-1";
};
config-2 {
/* DT+SoM+board model */
- description = "arrow,stm32mp15xx-avenger96_somrev0_boardrev1";
+ description = "arrow,stm32mp157a-avenger96_somrev0_boardrev1";
firmware = "uboot";
fdt = "fdt-2";
};
config-3 {
/* DT+SoM+board model */
- description = "dh,stm32mp15xx-dhcor-drc-compact_somrev0_boardrev0";
+ description = "dh,stm32mp153c-dhcor-drc-compact_somrev0_boardrev0";
firmware = "uboot";
fdt = "fdt-3";
};
CONFIG_ENV_SIZE=0x4000
CONFIG_ENV_OFFSET=0x3E0000
CONFIG_ENV_SECT_SIZE=0x1000
-CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dhcor-dhsbc"
+CONFIG_DEFAULT_DEVICE_TREE="st/stm32mp135f-dhcor-dhsbc"
CONFIG_SYS_BOOTM_LEN=0x2000000
CONFIG_SYS_LOAD_ADDR=0xc2000000
CONFIG_STM32MP13X=y
CONFIG_CMD_UBI=y
# CONFIG_ISO_PARTITION is not set
CONFIG_OF_LIVE=y
+CONFIG_OF_UPSTREAM=y
CONFIG_ENV_IS_NOWHERE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_ENV_SIZE=0x4000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="stm32mp15xx-dhcom-pdk2"
+CONFIG_DEFAULT_DEVICE_TREE="st/stm32mp157c-dhcom-pdk2"
CONFIG_SPL_TEXT_BASE=0x2FFC2500
CONFIG_SPL_MMC=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
# CONFIG_ISO_PARTITION is not set
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_OF_LIVE=y
-CONFIG_OF_LIST="stm32mp15xx-dhcom-pdk2 stm32mp15xx-dhcom-drc02 stm32mp15xx-dhcom-picoitx"
+CONFIG_OF_UPSTREAM=y
+CONFIG_OF_LIST="st/stm32mp157c-dhcom-pdk2 st/stm32mp153c-dhcom-drc02 st/stm32mp157c-dhcom-picoitx"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_SIZE=0x4000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="stm32mp15xx-dhcor-avenger96"
+CONFIG_DEFAULT_DEVICE_TREE="st/stm32mp157a-dhcor-avenger96"
CONFIG_SPL_TEXT_BASE=0x2FFC2500
CONFIG_SPL_MMC=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
# CONFIG_ISO_PARTITION is not set
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_OF_LIVE=y
-CONFIG_OF_LIST="stm32mp15xx-dhcor-avenger96 stm32mp15xx-dhcor-testbench stm32mp15xx-dhcor-drc-compact"
+CONFIG_OF_UPSTREAM=y
+CONFIG_OF_LIST="st/stm32mp157a-dhcor-avenger96 st/stm32mp151a-dhcor-testbench st/stm32mp153c-dhcor-drc-compact"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
projects / u-boot.git / commitdiff
