With the last user of this driver removed, remove the driver.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
+++ /dev/null
-This driver supports NE2000 compatible cards (those based on DP8390,
-DP83902 and similar). It can be used with PCMCIA/CF cards provided
-that the CCR is correctly initialized.
-
-The code is based on sources from the Linux kernel (pcnet_cs.c,
-8390.h) and eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2
-wonderful world are GPL, so this is, of course, GPL.
-
-I developed and tested this driver on a custom PXA255 based system and
-with a billionton CF network card connected to the PCMCIA interface of
-the micro (have a look at README.PXA_CF for the support of this port).
-
-The options you have to specify in the config file are (with the
-value for my board as an example):
-
-#define CONFIG_DRIVER_NE2000
-
-- Enables the driver
-
-#define CONFIG_DRIVER_NE2000_BASE (0x20000000+0x300)
-
-- Address where the board is mapped
-
-
-Enjoy!
-
-Christian Pellegrin <chri@ascensit.com>
+++ /dev/null
-/*
-
-Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
-
-Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
-eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
-are GPL, so this is, of course, GPL.
-
-*/
-
-/* Generic NS8390 register definitions. */
-/* This file is part of Donald Becker's 8390 drivers, and is distributed
- under the same license. Auto-loading of 8390.o only in v2.2 - Paul G.
- Some of these names and comments originated from the Crynwr
- packet drivers, which are distributed under the GPL. */
-
-#ifndef _8390_h
-#define _8390_h
-
-/* Some generic ethernet register configurations. */
-#define E8390_TX_IRQ_MASK 0xa /* For register EN0_ISR */
-#define E8390_RX_IRQ_MASK 0x5
-#define E8390_RXCONFIG 0x4 /* EN0_RXCR: broadcasts, no multicast,errors */
-#define E8390_RXOFF 0x20 /* EN0_RXCR: Accept no packets */
-#define E8390_TXCONFIG 0x00 /* EN0_TXCR: Normal transmit mode */
-#define E8390_TXOFF 0x02 /* EN0_TXCR: Transmitter off */
-
-/* Register accessed at EN_CMD, the 8390 base addr. */
-#define E8390_STOP 0x01 /* Stop and reset the chip */
-#define E8390_START 0x02 /* Start the chip, clear reset */
-#define E8390_TRANS 0x04 /* Transmit a frame */
-#define E8390_RREAD 0x08 /* Remote read */
-#define E8390_RWRITE 0x10 /* Remote write */
-#define E8390_NODMA 0x20 /* Remote DMA */
-#define E8390_PAGE0 0x00 /* Select page chip registers */
-#define E8390_PAGE1 0x40 /* using the two high-order bits */
-#define E8390_PAGE2 0x80 /* Page 3 is invalid. */
-
-/*
- * Only generate indirect loads given a machine that needs them.
- * - removed AMIGA_PCMCIA from this list, handled as ISA io now
- */
-
-#define n2k_inb(port) (*((volatile unsigned char *)(port+CONFIG_DRIVER_NE2000_BASE)))
-#define n2k_outb(val,port) (*((volatile unsigned char *)(port+CONFIG_DRIVER_NE2000_BASE)) = val)
-
-#define EI_SHIFT(x) (x)
-
-#define E8390_CMD EI_SHIFT(0x00) /* The command register (for all pages) */
-/* Page 0 register offsets. */
-#define EN0_CLDALO EI_SHIFT(0x01) /* Low byte of current local dma addr RD */
-#define EN0_STARTPG EI_SHIFT(0x01) /* Starting page of ring bfr WR */
-#define EN0_CLDAHI EI_SHIFT(0x02) /* High byte of current local dma addr RD */
-#define EN0_STOPPG EI_SHIFT(0x02) /* Ending page +1 of ring bfr WR */
-#define EN0_BOUNDARY EI_SHIFT(0x03) /* Boundary page of ring bfr RD WR */
-#define EN0_TSR EI_SHIFT(0x04) /* Transmit status reg RD */
-#define EN0_TPSR EI_SHIFT(0x04) /* Transmit starting page WR */
-#define EN0_NCR EI_SHIFT(0x05) /* Number of collision reg RD */
-#define EN0_TCNTLO EI_SHIFT(0x05) /* Low byte of tx byte count WR */
-#define EN0_FIFO EI_SHIFT(0x06) /* FIFO RD */
-#define EN0_TCNTHI EI_SHIFT(0x06) /* High byte of tx byte count WR */
-#define EN0_ISR EI_SHIFT(0x07) /* Interrupt status reg RD WR */
-#define EN0_CRDALO EI_SHIFT(0x08) /* low byte of current remote dma address RD */
-#define EN0_RSARLO EI_SHIFT(0x08) /* Remote start address reg 0 */
-#define EN0_CRDAHI EI_SHIFT(0x09) /* high byte, current remote dma address RD */
-#define EN0_RSARHI EI_SHIFT(0x09) /* Remote start address reg 1 */
-#define EN0_RCNTLO EI_SHIFT(0x0a) /* Remote byte count reg WR */
-#define EN0_RCNTHI EI_SHIFT(0x0b) /* Remote byte count reg WR */
-#define EN0_RSR EI_SHIFT(0x0c) /* rx status reg RD */
-#define EN0_RXCR EI_SHIFT(0x0c) /* RX configuration reg WR */
-#define EN0_TXCR EI_SHIFT(0x0d) /* TX configuration reg WR */
-#define EN0_COUNTER0 EI_SHIFT(0x0d) /* Rcv alignment error counter RD */
-#define EN0_DCFG EI_SHIFT(0x0e) /* Data configuration reg WR */
-#define EN0_COUNTER1 EI_SHIFT(0x0e) /* Rcv CRC error counter RD */
-#define EN0_IMR EI_SHIFT(0x0f) /* Interrupt mask reg WR */
-#define EN0_COUNTER2 EI_SHIFT(0x0f) /* Rcv missed frame error counter RD */
-
-/* Bits in EN0_ISR - Interrupt status register */
-#define ENISR_RX 0x01 /* Receiver, no error */
-#define ENISR_TX 0x02 /* Transmitter, no error */
-#define ENISR_RX_ERR 0x04 /* Receiver, with error */
-#define ENISR_TX_ERR 0x08 /* Transmitter, with error */
-#define ENISR_OVER 0x10 /* Receiver overwrote the ring */
-#define ENISR_COUNTERS 0x20 /* Counters need emptying */
-#define ENISR_RDC 0x40 /* remote dma complete */
-#define ENISR_RESET 0x80 /* Reset completed */
-#define ENISR_ALL 0x3f /* Interrupts we will enable */
-
-/* Bits in EN0_DCFG - Data config register */
-#define ENDCFG_WTS 0x01 /* word transfer mode selection */
-#define ENDCFG_BOS 0x02 /* byte order selection */
-#define ENDCFG_AUTO_INIT 0x10 /* Auto-init to remove packets from ring */
-#define ENDCFG_FIFO 0x40 /* 8 bytes */
-
-/* Page 1 register offsets. */
-#define EN1_PHYS EI_SHIFT(0x01) /* This board's physical enet addr RD WR */
-#define EN1_PHYS_SHIFT(i) EI_SHIFT(i+1) /* Get and set mac address */
-#define EN1_CURPAG EI_SHIFT(0x07) /* Current memory page RD WR */
-#define EN1_MULT EI_SHIFT(0x08) /* Multicast filter mask array (8 bytes) RD WR */
-#define EN1_MULT_SHIFT(i) EI_SHIFT(8+i) /* Get and set multicast filter */
-
-/* Bits in received packet status byte and EN0_RSR*/
-#define ENRSR_RXOK 0x01 /* Received a good packet */
-#define ENRSR_CRC 0x02 /* CRC error */
-#define ENRSR_FAE 0x04 /* frame alignment error */
-#define ENRSR_FO 0x08 /* FIFO overrun */
-#define ENRSR_MPA 0x10 /* missed pkt */
-#define ENRSR_PHY 0x20 /* physical/multicast address */
-#define ENRSR_DIS 0x40 /* receiver disable. set in monitor mode */
-#define ENRSR_DEF 0x80 /* deferring */
-
-/* Transmitted packet status, EN0_TSR. */
-#define ENTSR_PTX 0x01 /* Packet transmitted without error */
-#define ENTSR_ND 0x02 /* The transmit wasn't deferred. */
-#define ENTSR_COL 0x04 /* The transmit collided at least once. */
-#define ENTSR_ABT 0x08 /* The transmit collided 16 times, and was deferred. */
-#define ENTSR_CRS 0x10 /* The carrier sense was lost. */
-#define ENTSR_FU 0x20 /* A "FIFO underrun" occurred during transmit. */
-#define ENTSR_CDH 0x40 /* The collision detect "heartbeat" signal was lost. */
-#define ENTSR_OWC 0x80 /* There was an out-of-window collision. */
-
-#define NIC_RECEIVE_MONITOR_MODE 0x20
-
-#endif /* _8390_h */
obj-$(CONFIG_MVNETA) += mvneta.o
obj-$(CONFIG_MVPP2) += mvpp2.o
obj-$(CONFIG_NATSEMI) += natsemi.o
-obj-$(CONFIG_DRIVER_NE2000) += ne2000.o ne2000_base.o
obj-$(CONFIG_NETCONSOLE) += netconsole.o
obj-$(CONFIG_NS8382X) += ns8382x.o
obj-$(CONFIG_PCH_GBE) += pch_gbe.o
+++ /dev/null
-/*
-Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
-
-Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
-eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
-are GPL, so this is, of course, GPL.
-
-==========================================================================
-
-dev/if_dp83902a.c
-
-Ethernet device driver for NS DP83902a ethernet controller
-
-==========================================================================
-####ECOSGPLCOPYRIGHTBEGIN####
--------------------------------------------
-This file is part of eCos, the Embedded Configurable Operating System.
-Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-
-eCos is free software; you can redistribute it and/or modify it under
-the terms of the GNU General Public License as published by the Free
-Software Foundation; either version 2 or (at your option) any later version.
-
-eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-for more details.
-
-You should have received a copy of the GNU General Public License along
-with eCos; if not, write to the Free Software Foundation, Inc.,
-59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-
-As a special exception, if other files instantiate templates or use macros
-or inline functions from this file, or you compile this file and link it
-with other works to produce a work based on this file, this file does not
-by itself cause the resulting work to be covered by the GNU General Public
-License. However the source code for this file must still be made available
-in accordance with section (3) of the GNU General Public License.
-
-This exception does not invalidate any other reasons why a work based on
-this file might be covered by the GNU General Public License.
-
-Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-at http://sources.redhat.com/ecos/ecos-license/
--------------------------------------------
-####ECOSGPLCOPYRIGHTEND####
-####BSDCOPYRIGHTBEGIN####
-
--------------------------------------------
-
-Portions of this software may have been derived from OpenBSD or other sources,
-and are covered by the appropriate copyright disclaimers included herein.
-
--------------------------------------------
-
-####BSDCOPYRIGHTEND####
-==========================================================================
-#####DESCRIPTIONBEGIN####
-
-Author(s): gthomas
-Contributors: gthomas, jskov, rsandifo
-Date: 2001-06-13
-Purpose:
-Description:
-
-FIXME: Will fail if pinged with large packets (1520 bytes)
-Add promisc config
-Add SNMP
-
-####DESCRIPTIONEND####
-
-==========================================================================
-*/
-
-#include <common.h>
-#include <command.h>
-#include <linux/delay.h>
-
-/* NE2000 base header file */
-#include "ne2000_base.h"
-
-/* find prom (taken from pc_net_cs.c from Linux) */
-
-#include "8390.h"
-/*
-typedef struct hw_info_t {
- u_int offset;
- u_char a0, a1, a2;
- u_int flags;
-} hw_info_t;
-*/
-#define DELAY_OUTPUT 0x01
-#define HAS_MISC_REG 0x02
-#define USE_BIG_BUF 0x04
-#define HAS_IBM_MISC 0x08
-#define IS_DL10019 0x10
-#define IS_DL10022 0x20
-#define HAS_MII 0x40
-#define USE_SHMEM 0x80 /* autodetected */
-
-#define AM79C9XX_HOME_PHY 0x00006B90 /* HomePNA PHY */
-#define AM79C9XX_ETH_PHY 0x00006B70 /* 10baseT PHY */
-#define MII_PHYID_REV_MASK 0xfffffff0
-#define MII_PHYID_REG1 0x02
-#define MII_PHYID_REG2 0x03
-
-static hw_info_t hw_info[] = {
- { /* Accton EN2212 */ 0x0ff0, 0x00, 0x00, 0xe8, DELAY_OUTPUT },
- { /* Allied Telesis LA-PCM */ 0x0ff0, 0x00, 0x00, 0xf4, 0 },
- { /* APEX MultiCard */ 0x03f4, 0x00, 0x20, 0xe5, 0 },
- { /* ASANTE FriendlyNet */ 0x4910, 0x00, 0x00, 0x94,
- DELAY_OUTPUT | HAS_IBM_MISC },
- { /* Danpex EN-6200P2 */ 0x0110, 0x00, 0x40, 0xc7, 0 },
- { /* DataTrek NetCard */ 0x0ff0, 0x00, 0x20, 0xe8, 0 },
- { /* Dayna CommuniCard E */ 0x0110, 0x00, 0x80, 0x19, 0 },
- { /* D-Link DE-650 */ 0x0040, 0x00, 0x80, 0xc8, 0 },
- { /* EP-210 Ethernet */ 0x0110, 0x00, 0x40, 0x33, 0 },
- { /* EP4000 Ethernet */ 0x01c0, 0x00, 0x00, 0xb4, 0 },
- { /* Epson EEN10B */ 0x0ff0, 0x00, 0x00, 0x48,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* ELECOM Laneed LD-CDWA */ 0xb8, 0x08, 0x00, 0x42, 0 },
- { /* Hypertec Ethernet */ 0x01c0, 0x00, 0x40, 0x4c, 0 },
- { /* IBM CCAE */ 0x0ff0, 0x08, 0x00, 0x5a,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* IBM CCAE */ 0x0ff0, 0x00, 0x04, 0xac,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* IBM CCAE */ 0x0ff0, 0x00, 0x06, 0x29,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* IBM FME */ 0x0374, 0x08, 0x00, 0x5a,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* IBM FME */ 0x0374, 0x00, 0x04, 0xac,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* Kansai KLA-PCM/T */ 0x0ff0, 0x00, 0x60, 0x87,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* NSC DP83903 */ 0x0374, 0x08, 0x00, 0x17,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* NSC DP83903 */ 0x0374, 0x00, 0xc0, 0xa8,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* NSC DP83903 */ 0x0374, 0x00, 0xa0, 0xb0,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* NSC DP83903 */ 0x0198, 0x00, 0x20, 0xe0,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* I-O DATA PCLA/T */ 0x0ff0, 0x00, 0xa0, 0xb0, 0 },
- { /* Katron PE-520 */ 0x0110, 0x00, 0x40, 0xf6, 0 },
- { /* Kingston KNE-PCM/x */ 0x0ff0, 0x00, 0xc0, 0xf0,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* Kingston KNE-PCM/x */ 0x0ff0, 0xe2, 0x0c, 0x0f,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* Kingston KNE-PC2 */ 0x0180, 0x00, 0xc0, 0xf0, 0 },
- { /* Maxtech PCN2000 */ 0x5000, 0x00, 0x00, 0xe8, 0 },
- { /* NDC Instant-Link */ 0x003a, 0x00, 0x80, 0xc6, 0 },
- { /* NE2000 Compatible */ 0x0ff0, 0x00, 0xa0, 0x0c, 0 },
- { /* Network General Sniffer */ 0x0ff0, 0x00, 0x00, 0x65,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* Panasonic VEL211 */ 0x0ff0, 0x00, 0x80, 0x45,
- HAS_MISC_REG | HAS_IBM_MISC },
- { /* PreMax PE-200 */ 0x07f0, 0x00, 0x20, 0xe0, 0 },
- { /* RPTI EP400 */ 0x0110, 0x00, 0x40, 0x95, 0 },
- { /* SCM Ethernet */ 0x0ff0, 0x00, 0x20, 0xcb, 0 },
- { /* Socket EA */ 0x4000, 0x00, 0xc0, 0x1b,
- DELAY_OUTPUT | HAS_MISC_REG | USE_BIG_BUF },
- { /* Socket LP-E CF+ */ 0x01c0, 0x00, 0xc0, 0x1b, 0 },
- { /* SuperSocket RE450T */ 0x0110, 0x00, 0xe0, 0x98, 0 },
- { /* Volktek NPL-402CT */ 0x0060, 0x00, 0x40, 0x05, 0 },
- { /* NEC PC-9801N-J12 */ 0x0ff0, 0x00, 0x00, 0x4c, 0 },
- { /* PCMCIA Technology OEM */ 0x01c8, 0x00, 0xa0, 0x0c, 0 },
- { /* Qemu */ 0x0, 0x52, 0x54, 0x00, 0 },
- { /* RTL8019AS */ 0x0, 0x0, 0x18, 0x5f, 0 }
-};
-
-#define NR_INFO (sizeof(hw_info)/sizeof(hw_info_t))
-
-#define PCNET_CMD 0x00
-#define PCNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */
-#define PCNET_RESET 0x1f /* Issue a read to reset, a write to clear. */
-#define PCNET_MISC 0x18 /* For IBM CCAE and Socket EA cards */
-
-static void pcnet_reset_8390(u8* addr)
-{
- int i, r;
-
- n2k_outb(E8390_NODMA + E8390_PAGE0+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
- PRINTK("cmd (at %lx) is %x\n", addr + E8390_CMD, n2k_inb(E8390_CMD));
- n2k_outb(E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD);
-
- n2k_outb(n2k_inb(PCNET_RESET), PCNET_RESET);
-
- for (i = 0; i < 100; i++) {
- if ((r = (n2k_inb(EN0_ISR) & ENISR_RESET)) != 0)
- break;
- PRINTK("got %x in reset\n", r);
- udelay(100);
- }
- n2k_outb(ENISR_RESET, EN0_ISR); /* Ack intr. */
-
- if (i == 100)
- printf("pcnet_reset_8390() did not complete.\n");
-} /* pcnet_reset_8390 */
-
-int get_prom(u8* mac_addr, u8* base_addr)
-{
- u8 prom[32];
- int i, j;
- struct {
- u_char value, offset;
- } program_seq[] = {
- {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
- {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */
- {0x00, EN0_RCNTLO}, /* Clear the count regs. */
- {0x00, EN0_RCNTHI},
- {0x00, EN0_IMR}, /* Mask completion irq. */
- {0xFF, EN0_ISR},
- {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */
- {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */
- {32, EN0_RCNTLO},
- {0x00, EN0_RCNTHI},
- {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */
- {0x00, EN0_RSARHI},
- {E8390_RREAD+E8390_START, E8390_CMD},
- };
-
- PRINTK ("trying to get MAC via prom reading\n");
-
- pcnet_reset_8390 (base_addr);
-
- mdelay (10);
-
- for (i = 0; i < ARRAY_SIZE(program_seq); i++)
- n2k_outb (program_seq[i].value, program_seq[i].offset);
-
- PRINTK ("PROM:");
- for (i = 0; i < 32; i++) {
- prom[i] = n2k_inb (PCNET_DATAPORT);
- PRINTK (" %02x", prom[i]);
- }
- PRINTK ("\n");
- for (i = 0; i < NR_INFO; i++) {
- if ((prom[0] == hw_info[i].a0) &&
- (prom[2] == hw_info[i].a1) &&
- (prom[4] == hw_info[i].a2)) {
- PRINTK ("matched board %d\n", i);
- break;
- }
- }
- if ((i < NR_INFO) || ((prom[28] == 0x57) && (prom[30] == 0x57))) {
- PRINTK ("on exit i is %d/%ld\n", i, NR_INFO);
- PRINTK ("MAC address is ");
- for (j = 0; j < 6; j++) {
- mac_addr[j] = prom[j << 1];
- PRINTK ("%02x:", mac_addr[i]);
- }
- PRINTK ("\n");
- return (i < NR_INFO) ? i : 0;
- }
- return 0;
-}
+++ /dev/null
-/*
-Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
-
-Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
-eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
-are GPL, so this is, of course, GPL.
-
-==========================================================================
-
- dev/dp83902a.h
-
- National Semiconductor DP83902a ethernet chip
-
-==========================================================================
-####ECOSGPLCOPYRIGHTBEGIN####
- -------------------------------------------
- This file is part of eCos, the Embedded Configurable Operating System.
- Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-
- eCos is free software; you can redistribute it and/or modify it under
- the terms of the GNU General Public License as published by the Free
- Software Foundation; either version 2 or (at your option) any later version.
-
- eCos is distributed in the hope that it will be useful, but WITHOUT ANY
- WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with eCos; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-
- As a special exception, if other files instantiate templates or use macros
- or inline functions from this file, or you compile this file and link it
- with other works to produce a work based on this file, this file does not
- by itself cause the resulting work to be covered by the GNU General Public
- License. However the source code for this file must still be made available
- in accordance with section (3) of the GNU General Public License.
-
- This exception does not invalidate any other reasons why a work based on
- this file might be covered by the GNU General Public License.
-
- Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
- at http://sources.redhat.com/ecos/ecos-license/
- -------------------------------------------
-####ECOSGPLCOPYRIGHTEND####
-####BSDCOPYRIGHTBEGIN####
-
- -------------------------------------------
-
- Portions of this software may have been derived from OpenBSD or other sources,
- and are covered by the appropriate copyright disclaimers included herein.
-
- -------------------------------------------
-
-####BSDCOPYRIGHTEND####
-==========================================================================
-#####DESCRIPTIONBEGIN####
-
- Author(s): gthomas
- Contributors: gthomas, jskov
- Date: 2001-06-13
- Purpose:
- Description:
-
-####DESCRIPTIONEND####
-
-==========================================================================
-*/
-
-/*
- * NE2000 support header file.
- * Created by Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- */
-
-#ifndef __DRIVERS_NE2000_H__
-#define __DRIVERS_NE2000_H__
-
-/* Enable NE2000 basic init function */
-#define NE2000_BASIC_INIT
-
-#define DP_DATA 0x10
-#define START_PG 0x50 /* First page of TX buffer */
-#define START_PG2 0x48
-#define STOP_PG 0x80 /* Last page +1 of RX ring */
-
-#define RX_START 0x50
-#define RX_END 0x80
-
-#define DP_IN(_b_, _o_, _d_) (_d_) = *( (vu_char *) ((_b_)+(_o_)))
-#define DP_OUT(_b_, _o_, _d_) *( (vu_char *) ((_b_)+(_o_))) = (_d_)
-#define DP_IN_DATA(_b_, _d_) (_d_) = *( (vu_char *) ((_b_)))
-#define DP_OUT_DATA(_b_, _d_) *( (vu_char *) ((_b_))) = (_d_)
-#endif /* __DRIVERS_NE2000_H__ */
+++ /dev/null
-/*
-Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
-
-Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
-eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
-are GPL, so this is, of course, GPL.
-
-==========================================================================
-
-dev/if_dp83902a.c
-
-Ethernet device driver for NS DP83902a ethernet controller
-
-==========================================================================
-####ECOSGPLCOPYRIGHTBEGIN####
--------------------------------------------
-This file is part of eCos, the Embedded Configurable Operating System.
-Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-
-eCos is free software; you can redistribute it and/or modify it under
-the terms of the GNU General Public License as published by the Free
-Software Foundation; either version 2 or (at your option) any later version.
-
-eCos is distributed in the hope that it will be useful, but WITHOUT ANY
-WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-for more details.
-
-You should have received a copy of the GNU General Public License along
-with eCos; if not, write to the Free Software Foundation, Inc.,
-59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-
-As a special exception, if other files instantiate templates or use macros
-or inline functions from this file, or you compile this file and link it
-with other works to produce a work based on this file, this file does not
-by itself cause the resulting work to be covered by the GNU General Public
-License. However the source code for this file must still be made available
-in accordance with section (3) of the GNU General Public License.
-
-This exception does not invalidate any other reasons why a work based on
-this file might be covered by the GNU General Public License.
-
-Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
-at http://sources.redhat.com/ecos/ecos-license/
--------------------------------------------
-####ECOSGPLCOPYRIGHTEND####
-####BSDCOPYRIGHTBEGIN####
-
--------------------------------------------
-
-Portions of this software may have been derived from OpenBSD or other sources,
-and are covered by the appropriate copyright disclaimers included herein.
-
--------------------------------------------
-
-####BSDCOPYRIGHTEND####
-==========================================================================
-#####DESCRIPTIONBEGIN####
-
-Author(s): gthomas
-Contributors: gthomas, jskov, rsandifo
-Date: 2001-06-13
-Purpose:
-Description:
-
-FIXME: Will fail if pinged with large packets (1520 bytes)
-Add promisc config
-Add SNMP
-
-####DESCRIPTIONEND####
-
-==========================================================================
-*/
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <log.h>
-#include <net.h>
-#include <malloc.h>
-#include <linux/compiler.h>
-
-/* forward definition of function used for the uboot interface */
-void uboot_push_packet_len(int len);
-void uboot_push_tx_done(int key, int val);
-
-/* NE2000 base header file */
-#include "ne2000_base.h"
-
-#if defined(CONFIG_DRIVER_AX88796L)
-/* AX88796L support */
-#include "ax88796.h"
-#else
-/* Basic NE2000 chip support */
-#include "ne2000.h"
-#endif
-
-static dp83902a_priv_data_t nic; /* just one instance of the card supported */
-
-/**
- * This function reads the MAC address from the serial EEPROM,
- * used if PROM read fails. Does nothing for ax88796 chips (sh boards)
- */
-static bool
-dp83902a_init(unsigned char *enetaddr)
-{
- dp83902a_priv_data_t *dp = &nic;
- u8* base;
-#if defined(NE2000_BASIC_INIT)
- int i;
-#endif
-
- DEBUG_FUNCTION();
-
- base = dp->base;
- if (!base)
- return false; /* No device found */
-
- DEBUG_LINE();
-
-#if defined(NE2000_BASIC_INIT)
- /* AX88796L doesn't need */
- /* Prepare ESA */
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1); /* Select page 1 */
- /* Use the address from the serial EEPROM */
- for (i = 0; i < 6; i++)
- DP_IN(base, DP_P1_PAR0+i, dp->esa[i]);
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0); /* Select page 0 */
-
- printf("NE2000 - %s ESA: %02x:%02x:%02x:%02x:%02x:%02x\n",
- "eeprom",
- dp->esa[0],
- dp->esa[1],
- dp->esa[2],
- dp->esa[3],
- dp->esa[4],
- dp->esa[5] );
-
- memcpy(enetaddr, dp->esa, 6); /* Use MAC from serial EEPROM */
-#endif /* NE2000_BASIC_INIT */
- return true;
-}
-
-static void
-dp83902a_stop(void)
-{
- dp83902a_priv_data_t *dp = &nic;
- u8 *base = dp->base;
-
- DEBUG_FUNCTION();
-
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */
- DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */
- DP_OUT(base, DP_IMR, 0x00); /* Disable all interrupts */
-
- dp->running = false;
-}
-
-/*
- * This function is called to "start up" the interface. It may be called
- * multiple times, even when the hardware is already running. It will be
- * called whenever something "hardware oriented" changes and should leave
- * the hardware ready to send/receive packets.
- */
-static void
-dp83902a_start(u8 * enaddr)
-{
- dp83902a_priv_data_t *dp = &nic;
- u8 *base = dp->base;
- int i;
-
- debug("The MAC is %pM\n", enaddr);
-
- DEBUG_FUNCTION();
-
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_STOP); /* Brutal */
- DP_OUT(base, DP_DCR, DP_DCR_INIT);
- DP_OUT(base, DP_RBCH, 0); /* Remote byte count */
- DP_OUT(base, DP_RBCL, 0);
- DP_OUT(base, DP_RCR, DP_RCR_MON); /* Accept no packets */
- DP_OUT(base, DP_TCR, DP_TCR_LOCAL); /* Transmitter [virtually] off */
- DP_OUT(base, DP_TPSR, dp->tx_buf1); /* Transmitter start page */
- dp->tx1 = dp->tx2 = 0;
- dp->tx_next = dp->tx_buf1;
- dp->tx_started = false;
- dp->running = true;
- DP_OUT(base, DP_PSTART, dp->rx_buf_start); /* Receive ring start page */
- DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1); /* Receive ring boundary */
- DP_OUT(base, DP_PSTOP, dp->rx_buf_end); /* Receive ring end page */
- dp->rx_next = dp->rx_buf_start - 1;
- dp->running = true;
- DP_OUT(base, DP_ISR, 0xFF); /* Clear any pending interrupts */
- DP_OUT(base, DP_IMR, DP_IMR_All); /* Enable all interrupts */
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE1 | DP_CR_STOP); /* Select page 1 */
- DP_OUT(base, DP_P1_CURP, dp->rx_buf_start); /* Current page - next free page for Rx */
- dp->running = true;
- for (i = 0; i < ETHER_ADDR_LEN; i++) {
- /* FIXME */
- /*((vu_short*)( base + ((DP_P1_PAR0 + i) * 2) +
- * 0x1400)) = enaddr[i];*/
- DP_OUT(base, DP_P1_PAR0+i, enaddr[i]);
- }
- /* Enable and start device */
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
- DP_OUT(base, DP_TCR, DP_TCR_NORMAL); /* Normal transmit operations */
- DP_OUT(base, DP_RCR, DP_RCR_AB); /* Accept broadcast, no errors, no multicast */
- dp->running = true;
-}
-
-/*
- * This routine is called to start the transmitter. It is split out from the
- * data handling routine so it may be called either when data becomes first
- * available or when an Tx interrupt occurs
- */
-
-static void
-dp83902a_start_xmit(int start_page, int len)
-{
- dp83902a_priv_data_t *dp = (dp83902a_priv_data_t *) &nic;
- u8 *base = dp->base;
-
- DEBUG_FUNCTION();
-
-#if DEBUG & 1
- printf("Tx pkt %d len %d\n", start_page, len);
- if (dp->tx_started)
- printf("TX already started?!?\n");
-#endif
-
- DP_OUT(base, DP_ISR, (DP_ISR_TxP | DP_ISR_TxE));
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
- DP_OUT(base, DP_TBCL, len & 0xFF);
- DP_OUT(base, DP_TBCH, len >> 8);
- DP_OUT(base, DP_TPSR, start_page);
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START);
-
- dp->tx_started = true;
-}
-
-/*
- * This routine is called to send data to the hardware. It is known a-priori
- * that there is free buffer space (dp->tx_next).
- */
-static void
-dp83902a_send(u8 *data, int total_len, u32 key)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- int len, start_page, pkt_len, i, isr;
-#if DEBUG & 4
- int dx;
-#endif
-
- DEBUG_FUNCTION();
-
- len = pkt_len = total_len;
- if (pkt_len < IEEE_8023_MIN_FRAME)
- pkt_len = IEEE_8023_MIN_FRAME;
-
- start_page = dp->tx_next;
- if (dp->tx_next == dp->tx_buf1) {
- dp->tx1 = start_page;
- dp->tx1_len = pkt_len;
- dp->tx1_key = key;
- dp->tx_next = dp->tx_buf2;
- } else {
- dp->tx2 = start_page;
- dp->tx2_len = pkt_len;
- dp->tx2_key = key;
- dp->tx_next = dp->tx_buf1;
- }
-
-#if DEBUG & 5
- printf("TX prep page %d len %d\n", start_page, pkt_len);
-#endif
-
- DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */
- {
- /*
- * Dummy read. The manual sez something slightly different,
- * but the code is extended a bit to do what Hitachi's monitor
- * does (i.e., also read data).
- */
-
- __maybe_unused u16 tmp;
- int len = 1;
-
- DP_OUT(base, DP_RSAL, 0x100 - len);
- DP_OUT(base, DP_RSAH, (start_page - 1) & 0xff);
- DP_OUT(base, DP_RBCL, len);
- DP_OUT(base, DP_RBCH, 0);
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_RDMA | DP_CR_START);
- DP_IN_DATA(dp->data, tmp);
- }
-
-#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA
- /*
- * Stall for a bit before continuing to work around random data
- * corruption problems on some platforms.
- */
- CYGACC_CALL_IF_DELAY_US(1);
-#endif
-
- /* Send data to device buffer(s) */
- DP_OUT(base, DP_RSAL, 0);
- DP_OUT(base, DP_RSAH, start_page);
- DP_OUT(base, DP_RBCL, pkt_len & 0xFF);
- DP_OUT(base, DP_RBCH, pkt_len >> 8);
- DP_OUT(base, DP_CR, DP_CR_WDMA | DP_CR_START);
-
- /* Put data into buffer */
-#if DEBUG & 4
- printf(" sg buf %08lx len %08x\n ", (u32)data, len);
- dx = 0;
-#endif
- while (len > 0) {
-#if DEBUG & 4
- printf(" %02x", *data);
- if (0 == (++dx % 16)) printf("\n ");
-#endif
-
- DP_OUT_DATA(dp->data, *data++);
- len--;
- }
-#if DEBUG & 4
- printf("\n");
-#endif
- if (total_len < pkt_len) {
-#if DEBUG & 4
- printf(" + %d bytes of padding\n", pkt_len - total_len);
-#endif
- /* Padding to 802.3 length was required */
- for (i = total_len; i < pkt_len;) {
- i++;
- DP_OUT_DATA(dp->data, 0);
- }
- }
-
-#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA
- /*
- * After last data write, delay for a bit before accessing the
- * device again, or we may get random data corruption in the last
- * datum (on some platforms).
- */
- CYGACC_CALL_IF_DELAY_US(1);
-#endif
-
- /* Wait for DMA to complete */
- do {
- DP_IN(base, DP_ISR, isr);
- } while ((isr & DP_ISR_RDC) == 0);
-
- /* Then disable DMA */
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
-
- /* Start transmit if not already going */
- if (!dp->tx_started) {
- if (start_page == dp->tx1) {
- dp->tx_int = 1; /* Expecting interrupt from BUF1 */
- } else {
- dp->tx_int = 2; /* Expecting interrupt from BUF2 */
- }
- dp83902a_start_xmit(start_page, pkt_len);
- }
-}
-
-/*
- * This function is called when a packet has been received. It's job is
- * to prepare to unload the packet from the hardware. Once the length of
- * the packet is known, the upper layer of the driver can be told. When
- * the upper layer is ready to unload the packet, the internal function
- * 'dp83902a_recv' will be called to actually fetch it from the hardware.
- */
-static void
-dp83902a_RxEvent(void)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- __maybe_unused u8 rsr;
- u8 rcv_hdr[4];
- int i, len, pkt, cur;
-
- DEBUG_FUNCTION();
-
- DP_IN(base, DP_RSR, rsr);
- while (true) {
- /* Read incoming packet header */
- DP_OUT(base, DP_CR, DP_CR_PAGE1 | DP_CR_NODMA | DP_CR_START);
- DP_IN(base, DP_P1_CURP, cur);
- DP_OUT(base, DP_P1_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
- DP_IN(base, DP_BNDRY, pkt);
-
- pkt += 1;
- if (pkt == dp->rx_buf_end)
- pkt = dp->rx_buf_start;
-
- if (pkt == cur) {
- break;
- }
- DP_OUT(base, DP_RBCL, sizeof(rcv_hdr));
- DP_OUT(base, DP_RBCH, 0);
- DP_OUT(base, DP_RSAL, 0);
- DP_OUT(base, DP_RSAH, pkt);
- if (dp->rx_next == pkt) {
- if (cur == dp->rx_buf_start)
- DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1);
- else
- DP_OUT(base, DP_BNDRY, cur - 1); /* Update pointer */
- return;
- }
- dp->rx_next = pkt;
- DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */
- DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START);
-#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA
- CYGACC_CALL_IF_DELAY_US(10);
-#endif
-
- /* read header (get data size)*/
- for (i = 0; i < sizeof(rcv_hdr);) {
- DP_IN_DATA(dp->data, rcv_hdr[i++]);
- }
-
-#if DEBUG & 5
- printf("rx hdr %02x %02x %02x %02x\n",
- rcv_hdr[0], rcv_hdr[1], rcv_hdr[2], rcv_hdr[3]);
-#endif
- len = ((rcv_hdr[3] << 8) | rcv_hdr[2]) - sizeof(rcv_hdr);
-
- /* data read */
- uboot_push_packet_len(len);
-
- if (rcv_hdr[1] == dp->rx_buf_start)
- DP_OUT(base, DP_BNDRY, dp->rx_buf_end - 1);
- else
- DP_OUT(base, DP_BNDRY, rcv_hdr[1] - 1); /* Update pointer */
- }
-}
-
-/*
- * This function is called as a result of the "eth_drv_recv()" call above.
- * It's job is to actually fetch data for a packet from the hardware once
- * memory buffers have been allocated for the packet. Note that the buffers
- * may come in pieces, using a scatter-gather list. This allows for more
- * efficient processing in the upper layers of the stack.
- */
-static void
-dp83902a_recv(u8 *data, int len)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- int i, mlen;
- u8 saved_char = 0;
- bool saved;
-#if DEBUG & 4
- int dx;
-#endif
-
- DEBUG_FUNCTION();
-
-#if DEBUG & 5
- printf("Rx packet %d length %d\n", dp->rx_next, len);
-#endif
-
- /* Read incoming packet data */
- DP_OUT(base, DP_CR, DP_CR_PAGE0 | DP_CR_NODMA | DP_CR_START);
- DP_OUT(base, DP_RBCL, len & 0xFF);
- DP_OUT(base, DP_RBCH, len >> 8);
- DP_OUT(base, DP_RSAL, 4); /* Past header */
- DP_OUT(base, DP_RSAH, dp->rx_next);
- DP_OUT(base, DP_ISR, DP_ISR_RDC); /* Clear end of DMA */
- DP_OUT(base, DP_CR, DP_CR_RDMA | DP_CR_START);
-#ifdef CYGHWR_NS_DP83902A_PLF_BROKEN_RX_DMA
- CYGACC_CALL_IF_DELAY_US(10);
-#endif
-
- saved = false;
- for (i = 0; i < 1; i++) {
- if (data) {
- mlen = len;
-#if DEBUG & 4
- printf(" sg buf %08lx len %08x \n", (u32) data, mlen);
- dx = 0;
-#endif
- while (0 < mlen) {
- /* Saved byte from previous loop? */
- if (saved) {
- *data++ = saved_char;
- mlen--;
- saved = false;
- continue;
- }
-
- {
- u8 tmp;
- DP_IN_DATA(dp->data, tmp);
-#if DEBUG & 4
- printf(" %02x", tmp);
- if (0 == (++dx % 16)) printf("\n ");
-#endif
- *data++ = tmp;
- mlen--;
- }
- }
-#if DEBUG & 4
- printf("\n");
-#endif
- }
- }
-}
-
-static void
-dp83902a_TxEvent(void)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- __maybe_unused u8 tsr;
- u32 key;
-
- DEBUG_FUNCTION();
-
- DP_IN(base, DP_TSR, tsr);
- if (dp->tx_int == 1) {
- key = dp->tx1_key;
- dp->tx1 = 0;
- } else {
- key = dp->tx2_key;
- dp->tx2 = 0;
- }
- /* Start next packet if one is ready */
- dp->tx_started = false;
- if (dp->tx1) {
- dp83902a_start_xmit(dp->tx1, dp->tx1_len);
- dp->tx_int = 1;
- } else if (dp->tx2) {
- dp83902a_start_xmit(dp->tx2, dp->tx2_len);
- dp->tx_int = 2;
- } else {
- dp->tx_int = 0;
- }
- /* Tell higher level we sent this packet */
- uboot_push_tx_done(key, 0);
-}
-
-/*
- * Read the tally counters to clear them. Called in response to a CNT
- * interrupt.
- */
-static void
-dp83902a_ClearCounters(void)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- __maybe_unused u8 cnt1, cnt2, cnt3;
-
- DP_IN(base, DP_FER, cnt1);
- DP_IN(base, DP_CER, cnt2);
- DP_IN(base, DP_MISSED, cnt3);
- DP_OUT(base, DP_ISR, DP_ISR_CNT);
-}
-
-/*
- * Deal with an overflow condition. This code follows the procedure set
- * out in section 7.0 of the datasheet.
- */
-static void
-dp83902a_Overflow(void)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *)&nic;
- u8 *base = dp->base;
- u8 isr;
-
- /* Issue a stop command and wait 1.6ms for it to complete. */
- DP_OUT(base, DP_CR, DP_CR_STOP | DP_CR_NODMA);
- CYGACC_CALL_IF_DELAY_US(1600);
-
- /* Clear the remote byte counter registers. */
- DP_OUT(base, DP_RBCL, 0);
- DP_OUT(base, DP_RBCH, 0);
-
- /* Enter loopback mode while we clear the buffer. */
- DP_OUT(base, DP_TCR, DP_TCR_LOCAL);
- DP_OUT(base, DP_CR, DP_CR_START | DP_CR_NODMA);
-
- /*
- * Read in as many packets as we can and acknowledge any and receive
- * interrupts. Since the buffer has overflowed, a receive event of
- * some kind will have occurred.
- */
- dp83902a_RxEvent();
- DP_OUT(base, DP_ISR, DP_ISR_RxP|DP_ISR_RxE);
-
- /* Clear the overflow condition and leave loopback mode. */
- DP_OUT(base, DP_ISR, DP_ISR_OFLW);
- DP_OUT(base, DP_TCR, DP_TCR_NORMAL);
-
- /*
- * If a transmit command was issued, but no transmit event has occurred,
- * restart it here.
- */
- DP_IN(base, DP_ISR, isr);
- if (dp->tx_started && !(isr & (DP_ISR_TxP|DP_ISR_TxE))) {
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_TXPKT | DP_CR_START);
- }
-}
-
-static void
-dp83902a_poll(void)
-{
- struct dp83902a_priv_data *dp = (struct dp83902a_priv_data *) &nic;
- u8 *base = dp->base;
- u8 isr;
-
- DP_OUT(base, DP_CR, DP_CR_NODMA | DP_CR_PAGE0 | DP_CR_START);
- DP_IN(base, DP_ISR, isr);
- while (0 != isr) {
- /*
- * The CNT interrupt triggers when the MSB of one of the error
- * counters is set. We don't much care about these counters, but
- * we should read their values to reset them.
- */
- if (isr & DP_ISR_CNT) {
- dp83902a_ClearCounters();
- }
- /*
- * Check for overflow. It's a special case, since there's a
- * particular procedure that must be followed to get back into
- * a running state.a
- */
- if (isr & DP_ISR_OFLW) {
- dp83902a_Overflow();
- } else {
- /*
- * Other kinds of interrupts can be acknowledged simply by
- * clearing the relevant bits of the ISR. Do that now, then
- * handle the interrupts we care about.
- */
- DP_OUT(base, DP_ISR, isr); /* Clear set bits */
- if (!dp->running) break; /* Is this necessary? */
- /*
- * Check for tx_started on TX event since these may happen
- * spuriously it seems.
- */
- if (isr & (DP_ISR_TxP|DP_ISR_TxE) && dp->tx_started) {
- dp83902a_TxEvent();
- }
- if (isr & (DP_ISR_RxP|DP_ISR_RxE)) {
- dp83902a_RxEvent();
- }
- }
- DP_IN(base, DP_ISR, isr);
- }
-}
-
-
-/* U-Boot specific routines */
-static u8 *pbuf = NULL;
-
-static int pkey = -1;
-static int initialized = 0;
-
-void uboot_push_packet_len(int len) {
- PRINTK("pushed len = %d\n", len);
- if (len >= 2000) {
- printf("NE2000: packet too big\n");
- return;
- }
- dp83902a_recv(&pbuf[0], len);
-
- /*Just pass it to the upper layer*/
- net_process_received_packet(&pbuf[0], len);
-}
-
-void uboot_push_tx_done(int key, int val) {
- PRINTK("pushed key = %d\n", key);
- pkey = key;
-}
-
-/**
- * Setup the driver and init MAC address according to doc/README.enetaddr
- * Called by ne2k_register() before registering the driver @eth layer
- *
- * @param struct ethdevice of this instance of the driver for dev->enetaddr
- * @return 0 on success, -1 on error (causing caller to print error msg)
- */
-static int ne2k_setup_driver(struct eth_device *dev)
-{
- PRINTK("### ne2k_setup_driver\n");
-
- if (!pbuf) {
- pbuf = malloc(2000);
- if (!pbuf) {
- printf("Cannot allocate rx buffer\n");
- return -1;
- }
- }
-
- nic.base = (u8 *) CONFIG_DRIVER_NE2000_BASE;
-
- nic.data = nic.base + DP_DATA;
- nic.tx_buf1 = START_PG;
- nic.tx_buf2 = START_PG2;
- nic.rx_buf_start = RX_START;
- nic.rx_buf_end = RX_END;
-
- /*
- * According to doc/README.enetaddr, drivers shall give priority
- * to the MAC address value in the environment, so we do not read
- * it from the prom or eeprom if it is specified in the environment.
- */
- if (!eth_env_get_enetaddr("ethaddr", dev->enetaddr)) {
- /* If the MAC address is not in the environment, get it: */
- if (!get_prom(dev->enetaddr, nic.base)) /* get MAC from prom */
- dp83902a_init(dev->enetaddr); /* fallback: seeprom */
- /* And write it into the environment otherwise eth_write_hwaddr
- * returns -1 due to eth_env_get_enetaddr_by_index() failing,
- * and this causes "Warning: failed to set MAC address", and
- * cmd_bdinfo has no ethaddr value which it can show: */
- eth_env_set_enetaddr("ethaddr", dev->enetaddr);
- }
- return 0;
-}
-
-static int ne2k_init(struct eth_device *dev, struct bd_info *bd)
-{
- dp83902a_start(dev->enetaddr);
- initialized = 1;
- return 0;
-}
-
-static void ne2k_halt(struct eth_device *dev)
-{
- debug("### ne2k_halt\n");
- if(initialized)
- dp83902a_stop();
- initialized = 0;
-}
-
-static int ne2k_recv(struct eth_device *dev)
-{
- dp83902a_poll();
- return 1;
-}
-
-static int ne2k_send(struct eth_device *dev, void *packet, int length)
-{
- int tmo;
-
- debug("### ne2k_send\n");
-
- pkey = -1;
-
- dp83902a_send((u8 *) packet, length, 666);
- tmo = get_timer (0) + TOUT * CONFIG_SYS_HZ;
- while(1) {
- dp83902a_poll();
- if (pkey != -1) {
- PRINTK("Packet sucesfully sent\n");
- return 0;
- }
- if (get_timer (0) >= tmo) {
- printf("transmission error (timoeut)\n");
- return 0;
- }
-
- }
- return 0;
-}
-
-/**
- * Setup the driver for use and register it with the eth layer
- * @return 0 on success, -1 on error (causing caller to print error msg)
- */
-int ne2k_register(void)
-{
- struct eth_device *dev;
-
- dev = calloc(sizeof(*dev), 1);
- if (dev == NULL)
- return -1;
-
- if (ne2k_setup_driver(dev))
- return -1;
-
- dev->init = ne2k_init;
- dev->halt = ne2k_halt;
- dev->send = ne2k_send;
- dev->recv = ne2k_recv;
-
- strcpy(dev->name, "NE2000");
-
- return eth_register(dev);
-}
+++ /dev/null
-/*
-Ported to U-Boot by Christian Pellegrin <chri@ascensit.com>
-
-Based on sources from the Linux kernel (pcnet_cs.c, 8390.h) and
-eCOS(if_dp83902a.c, if_dp83902a.h). Both of these 2 wonderful world
-are GPL, so this is, of course, GPL.
-
-
-==========================================================================
-
- dev/dp83902a.h
-
- National Semiconductor DP83902a ethernet chip
-
-==========================================================================
-####ECOSGPLCOPYRIGHTBEGIN####
- -------------------------------------------
- This file is part of eCos, the Embedded Configurable Operating System.
- Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
-
- eCos is free software; you can redistribute it and/or modify it under
- the terms of the GNU General Public License as published by the Free
- Software Foundation; either version 2 or (at your option) any later version.
-
- eCos is distributed in the hope that it will be useful, but WITHOUT ANY
- WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with eCos; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
-
- As a special exception, if other files instantiate templates or use macros
- or inline functions from this file, or you compile this file and link it
- with other works to produce a work based on this file, this file does not
- by itself cause the resulting work to be covered by the GNU General Public
- License. However the source code for this file must still be made available
- in accordance with section (3) of the GNU General Public License.
-
- This exception does not invalidate any other reasons why a work based on
- this file might be covered by the GNU General Public License.
-
- Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.
- at http://sources.redhat.com/ecos/ecos-license/
- -------------------------------------------
-####ECOSGPLCOPYRIGHTEND####
-####BSDCOPYRIGHTBEGIN####
-
- -------------------------------------------
-
- Portions of this software may have been derived from OpenBSD or other sources,
- and are covered by the appropriate copyright disclaimers included herein.
-
- -------------------------------------------
-
-####BSDCOPYRIGHTEND####
-==========================================================================
-#####DESCRIPTIONBEGIN####
-
- Author(s): gthomas
- Contributors: gthomas, jskov
- Date: 2001-06-13
- Purpose:
- Description:
-
-####DESCRIPTIONEND####
-
-==========================================================================
-
-*/
-
-/*
- ------------------------------------------------------------------------
- Macros for accessing DP registers
- These can be overridden by the platform header
-*/
-
-#ifndef __NE2000_BASE_H__
-#define __NE2000_BASE_H__
-
-/*
- * Debugging details
- *
- * Set to perms of:
- * 0 disables all debug output
- * 1 for process debug output
- * 2 for added data IO output: get_reg, put_reg
- * 4 for packet allocation/free output
- * 8 for only startup status, so we can tell we're installed OK
- */
-#if 0
-#define DEBUG 0xf
-#else
-#define DEBUG 0
-#endif
-
-#if DEBUG & 1
-#define DEBUG_FUNCTION() do { printf("%s\n", __FUNCTION__); } while (0)
-#define DEBUG_LINE() do { printf("%d\n", __LINE__); } while (0)
-#define PRINTK(args...) printf(args)
-#else
-#define DEBUG_FUNCTION() do {} while(0)
-#define DEBUG_LINE() do {} while(0)
-#define PRINTK(args...)
-#endif
-
-/* timeout for tx/rx in s */
-#include <linux/delay.h>
-#define TOUT 5
-/* Ether MAC address size */
-#define ETHER_ADDR_LEN 6
-
-
-#define CYGHWR_NS_DP83902A_PLF_BROKEN_TX_DMA 1
-#define CYGACC_CALL_IF_DELAY_US(X) udelay(X)
-
-/* H/W infomation struct */
-typedef struct hw_info_t {
- u32 offset;
- u8 a0, a1, a2;
- u32 flags;
-} hw_info_t;
-
-typedef struct dp83902a_priv_data {
- u8* base;
- u8* data;
- u8* reset;
- int tx_next; /* First free Tx page */
- int tx_int; /* Expecting interrupt from this buffer */
- int rx_next; /* First free Rx page */
- int tx1, tx2; /* Page numbers for Tx buffers */
- u32 tx1_key, tx2_key; /* Used to ack when packet sent */
- int tx1_len, tx2_len;
- bool tx_started, running, hardwired_esa;
- u8 esa[6];
- void* plf_priv;
-
- /* Buffer allocation */
- int tx_buf1, tx_buf2;
- int rx_buf_start, rx_buf_end;
-} dp83902a_priv_data_t;
-
-/* ------------------------------------------------------------------------ */
-/* Register offsets */
-
-#define DP_CR 0x00
-#define DP_CLDA0 0x01
-#define DP_PSTART 0x01 /* write */
-#define DP_CLDA1 0x02
-#define DP_PSTOP 0x02 /* write */
-#define DP_BNDRY 0x03
-#define DP_TSR 0x04
-#define DP_TPSR 0x04 /* write */
-#define DP_NCR 0x05
-#define DP_TBCL 0x05 /* write */
-#define DP_FIFO 0x06
-#define DP_TBCH 0x06 /* write */
-#define DP_ISR 0x07
-#define DP_CRDA0 0x08
-#define DP_RSAL 0x08 /* write */
-#define DP_CRDA1 0x09
-#define DP_RSAH 0x09 /* write */
-#define DP_RBCL 0x0a /* write */
-#define DP_RBCH 0x0b /* write */
-#define DP_RSR 0x0c
-#define DP_RCR 0x0c /* write */
-#define DP_FER 0x0d
-#define DP_TCR 0x0d /* write */
-#define DP_CER 0x0e
-#define DP_DCR 0x0e /* write */
-#define DP_MISSED 0x0f
-#define DP_IMR 0x0f /* write */
-#define DP_DATAPORT 0x10 /* "eprom" data port */
-
-#define DP_P1_CR 0x00
-#define DP_P1_PAR0 0x01
-#define DP_P1_PAR1 0x02
-#define DP_P1_PAR2 0x03
-#define DP_P1_PAR3 0x04
-#define DP_P1_PAR4 0x05
-#define DP_P1_PAR5 0x06
-#define DP_P1_CURP 0x07
-#define DP_P1_MAR0 0x08
-#define DP_P1_MAR1 0x09
-#define DP_P1_MAR2 0x0a
-#define DP_P1_MAR3 0x0b
-#define DP_P1_MAR4 0x0c
-#define DP_P1_MAR5 0x0d
-#define DP_P1_MAR6 0x0e
-#define DP_P1_MAR7 0x0f
-
-#define DP_P2_CR 0x00
-#define DP_P2_PSTART 0x01
-#define DP_P2_CLDA0 0x01 /* write */
-#define DP_P2_PSTOP 0x02
-#define DP_P2_CLDA1 0x02 /* write */
-#define DP_P2_RNPP 0x03
-#define DP_P2_TPSR 0x04
-#define DP_P2_LNPP 0x05
-#define DP_P2_ACH 0x06
-#define DP_P2_ACL 0x07
-#define DP_P2_RCR 0x0c
-#define DP_P2_TCR 0x0d
-#define DP_P2_DCR 0x0e
-#define DP_P2_IMR 0x0f
-
-/* Command register - common to all pages */
-
-#define DP_CR_STOP 0x01 /* Stop: software reset */
-#define DP_CR_START 0x02 /* Start: initialize device */
-#define DP_CR_TXPKT 0x04 /* Transmit packet */
-#define DP_CR_RDMA 0x08 /* Read DMA (recv data from device) */
-#define DP_CR_WDMA 0x10 /* Write DMA (send data to device) */
-#define DP_CR_SEND 0x18 /* Send packet */
-#define DP_CR_NODMA 0x20 /* Remote (or no) DMA */
-#define DP_CR_PAGE0 0x00 /* Page select */
-#define DP_CR_PAGE1 0x40
-#define DP_CR_PAGE2 0x80
-#define DP_CR_PAGEMSK 0x3F /* Used to mask out page bits */
-
-/* Data configuration register */
-
-#define DP_DCR_WTS 0x01 /* 1=16 bit word transfers */
-#define DP_DCR_BOS 0x02 /* 1=Little Endian */
-#define DP_DCR_LAS 0x04 /* 1=Single 32 bit DMA mode */
-#define DP_DCR_LS 0x08 /* 1=normal mode, 0=loopback */
-#define DP_DCR_ARM 0x10 /* 0=no send command (program I/O) */
-#define DP_DCR_FIFO_1 0x00 /* FIFO threshold */
-#define DP_DCR_FIFO_2 0x20
-#define DP_DCR_FIFO_4 0x40
-#define DP_DCR_FIFO_6 0x60
-
-#define DP_DCR_INIT (DP_DCR_LS|DP_DCR_FIFO_4)
-
-/* Interrupt status register */
-
-#define DP_ISR_RxP 0x01 /* Packet received */
-#define DP_ISR_TxP 0x02 /* Packet transmitted */
-#define DP_ISR_RxE 0x04 /* Receive error */
-#define DP_ISR_TxE 0x08 /* Transmit error */
-#define DP_ISR_OFLW 0x10 /* Receive overflow */
-#define DP_ISR_CNT 0x20 /* Tally counters need emptying */
-#define DP_ISR_RDC 0x40 /* Remote DMA complete */
-#define DP_ISR_RESET 0x80 /* Device has reset (shutdown, error) */
-
-/* Interrupt mask register */
-
-#define DP_IMR_RxP 0x01 /* Packet received */
-#define DP_IMR_TxP 0x02 /* Packet transmitted */
-#define DP_IMR_RxE 0x04 /* Receive error */
-#define DP_IMR_TxE 0x08 /* Transmit error */
-#define DP_IMR_OFLW 0x10 /* Receive overflow */
-#define DP_IMR_CNT 0x20 /* Tall counters need emptying */
-#define DP_IMR_RDC 0x40 /* Remote DMA complete */
-
-#define DP_IMR_All 0x3F /* Everything but remote DMA */
-
-/* Receiver control register */
-
-#define DP_RCR_SEP 0x01 /* Save bad(error) packets */
-#define DP_RCR_AR 0x02 /* Accept runt packets */
-#define DP_RCR_AB 0x04 /* Accept broadcast packets */
-#define DP_RCR_AM 0x08 /* Accept multicast packets */
-#define DP_RCR_PROM 0x10 /* Promiscuous mode */
-#define DP_RCR_MON 0x20 /* Monitor mode - 1=accept no packets */
-
-/* Receiver status register */
-
-#define DP_RSR_RxP 0x01 /* Packet received */
-#define DP_RSR_CRC 0x02 /* CRC error */
-#define DP_RSR_FRAME 0x04 /* Framing error */
-#define DP_RSR_FO 0x08 /* FIFO overrun */
-#define DP_RSR_MISS 0x10 /* Missed packet */
-#define DP_RSR_PHY 0x20 /* 0=pad match, 1=mad match */
-#define DP_RSR_DIS 0x40 /* Receiver disabled */
-#define DP_RSR_DFR 0x80 /* Receiver processing deferred */
-
-/* Transmitter control register */
-
-#define DP_TCR_NOCRC 0x01 /* 1=inhibit CRC */
-#define DP_TCR_NORMAL 0x00 /* Normal transmitter operation */
-#define DP_TCR_LOCAL 0x02 /* Internal NIC loopback */
-#define DP_TCR_INLOOP 0x04 /* Full internal loopback */
-#define DP_TCR_OUTLOOP 0x08 /* External loopback */
-#define DP_TCR_ATD 0x10 /* Auto transmit disable */
-#define DP_TCR_OFFSET 0x20 /* Collision offset adjust */
-
-/* Transmit status register */
-
-#define DP_TSR_TxP 0x01 /* Packet transmitted */
-#define DP_TSR_COL 0x04 /* Collision (at least one) */
-#define DP_TSR_ABT 0x08 /* Aborted because of too many collisions */
-#define DP_TSR_CRS 0x10 /* Lost carrier */
-#define DP_TSR_FU 0x20 /* FIFO underrun */
-#define DP_TSR_CDH 0x40 /* Collision Detect Heartbeat */
-#define DP_TSR_OWC 0x80 /* Collision outside normal window */
-
-#define IEEE_8023_MAX_FRAME 1518 /* Largest possible ethernet frame */
-#define IEEE_8023_MIN_FRAME 64 /* Smallest possible ethernet frame */
-
-/* Functions */
-int get_prom(u8* mac_addr, u8* base_addr);
-
-#endif /* __NE2000_BASE_H__ */
projects / u-boot.git / commitdiff
