am335x: add initial AM335x IDK board support

This patch extends the am335x_evm board for the AM335x IDK.

The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).

The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 013ad881f0a082c8f1b044cefff246ac0e5f294e..e5ad76e9a05b6a379ce7543e34e879476438ac88 100644 (file)
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -68,6 +68,11 @@ static inline int board_is_evm_sk(void)
        return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
 }
 
+static inline int board_is_idk(void)
+{
+       return !strncmp(header.config, "SKU#02", 6);
+}
+
 /*
  * Read header information from EEPROM into global structure.
  */
@@ -378,7 +383,7 @@ int board_eth_init(bd_t *bis)
                        return -1;
        }
 
-       if (board_is_bone() || board_is_bone_lt()) {
+       if (board_is_bone() || board_is_bone_lt() || board_is_idk()) {
                writel(MII_MODE_ENABLE, &cdev->miisel);
                cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
                                PHY_INTERFACE_MODE_MII;

diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index acb8ff3e5c2fbe4f520e6369ab67583da87e1975..8437ef515afed9dc4fa27162f2a1407400ed0fd2 100644 (file)
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -69,6 +69,17 @@ static struct module_pin_mux mmc0_pin_mux[] = {
        {-1},
 };
 
+static struct module_pin_mux mmc0_no_cd_pin_mux[] = {
+       {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT3 */
+       {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT2 */
+       {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT1 */
+       {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT0 */
+       {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},   /* MMC0_CLK */
+       {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},   /* MMC0_CMD */
+       {OFFSET(mcasp0_aclkr), (MODE(4) | RXACTIVE)},           /* MMC0_WP */
+       {-1},
+};
+
 static struct module_pin_mux mmc0_pin_mux_sk_evm[] = {
        {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT3 */
        {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_DAT2 */
@@ -250,6 +261,15 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
                        configure_module_pin_mux(mmc1_pin_mux);
                        configure_module_pin_mux(spi0_pin_mux);
                }
+       } else if (!strncmp(header->config, "SKU#02", 6)) {
+               /*
+                * Industrial Motor Control (IDK)
+                * note: IDK console is on UART3 by default.
+                *       So u-boot mus be build with CONFIG_SERIAL4 and
+                *       CONFIG_CONS_INDEX=4
+                */
+               configure_module_pin_mux(mii1_pin_mux);
+               configure_module_pin_mux(mmc0_no_cd_pin_mux);
        } else if (!strncmp(header->name, "A335X_SK", HDR_NAME_LEN)) {
                /* Starter Kit EVM */
                configure_module_pin_mux(i2c1_pin_mux);