*************************************************************************
*/
+.globl _TEXT_BASE
_TEXT_BASE:
.word TEXT_BASE
_TEXT_PHY_BASE:
.word CONFIG_SYS_PHY_UBOOT_BASE
+#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
.globl _armboot_start
_armboot_start:
.word _start
+#endif
/*
* These are defined in the board-specific linker script.
_bss_end:
.word _end
+#if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
+/* IRQ stack memory (calculated at run-time) + 8 bytes */
+.globl IRQ_STACK_START_IN
+IRQ_STACK_START_IN:
+ .word 0x0badc0de
+
+.globl _datarel_start
+_datarel_start:
+ .word __datarel_start
+
+.globl _datarelrolocal_start
+_datarelrolocal_start:
+ .word __datarelrolocal_start
+
+.globl _datarellocal_start
+_datarellocal_start:
+ .word __datarellocal_start
+
+.globl _datarelro_start
+_datarelro_start:
+ .word __datarelro_start
+
+.globl _got_start
+_got_start:
+ .word __got_start
+
+.globl _got_end
+_got_end:
+ .word __got_end
+
+/*
+ * the actual reset code
+ */
+
+reset:
+ /*
+ * set the cpu to SVC32 mode
+ */
+ mrs r0, cpsr
+ bic r0, r0, #0x3f
+ orr r0, r0, #0xd3
+ msr cpsr, r0
+
+/*
+ *************************************************************************
+ *
+ * CPU_init_critical registers
+ *
+ * setup important registers
+ * setup memory timing
+ *
+ *************************************************************************
+ */
+ /*
+ * we do sys-critical inits only at reboot,
+ * not when booting from ram!
+ */
+cpu_init_crit:
+ /*
+ * When booting from NAND - it has definitely been a reset, so, no need
+ * to flush caches and disable the MMU
+ */
+#ifndef CONFIG_NAND_SPL
+ /*
+ * flush v4 I/D caches
+ */
+ mov r0, #0
+ mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */
+ mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
+
+ /*
+ * disable MMU stuff and caches
+ */
+ mrc p15, 0, r0, c1, c0, 0
+ bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS)
+ bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM)
+ orr r0, r0, #0x00000002 @ set bit 2 (A) Align
+ orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache
+
+ /* Prepare to disable the MMU */
+ adr r2, mmu_disable_phys
+ sub r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - TEXT_BASE)
+ b mmu_disable
+
+ .align 5
+ /* Run in a single cache-line */
+mmu_disable:
+ mcr p15, 0, r0, c1, c0, 0
+ nop
+ nop
+ mov pc, r2
+mmu_disable_phys:
+
+#ifdef CONFIG_DISABLE_TCM
+ /*
+ * Disable the TCMs
+ */
+ mrc p15, 0, r0, c0, c0, 2 /* Return TCM details */
+ cmp r0, #0
+ beq skip_tcmdisable
+ mov r1, #0
+ mov r2, #1
+ tst r0, r2
+ mcrne p15, 0, r1, c9, c1, 1 /* Disable Instruction TCM if present*/
+ tst r0, r2, LSL #16
+ mcrne p15, 0, r1, c9, c1, 0 /* Disable Data TCM if present*/
+skip_tcmdisable:
+#endif
+#endif
+
+#ifdef CONFIG_PERIPORT_REMAP
+ /* Peri port setup */
+ ldr r0, =CONFIG_PERIPORT_BASE
+ orr r0, r0, #CONFIG_PERIPORT_SIZE
+ mcr p15,0,r0,c15,c2,4
+#endif
+
+ /*
+ * Go setup Memory and board specific bits prior to relocation.
+ */
+ bl lowlevel_init /* go setup pll,mux,memory */
+
+/* Set stackpointer in internal RAM to call board_init_f */
+call_board_init_f:
+ ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
+ ldr r0,=0x00000000
+ bl board_init_f
+
+/*------------------------------------------------------------------------------*/
+
+/*
+ * void relocate_code (addr_sp, gd, addr_moni)
+ *
+ * This "function" does not return, instead it continues in RAM
+ * after relocating the monitor code.
+ *
+ */
+ .globl relocate_code
+relocate_code:
+ mov r4, r0 /* save addr_sp */
+ mov r5, r1 /* save addr of gd */
+ mov r6, r2 /* save addr of destination */
+ mov r7, r2 /* save addr of destination */
+
+ /* Set up the stack */
+stack_setup:
+ mov sp, r4
+
+ adr r0, _start
+ ldr r2, _TEXT_BASE
+ ldr r3, _bss_start
+ sub r2, r3, r2 /* r2 <- size of armboot */
+ add r2, r0, r2 /* r2 <- source end address */
+ cmp r0, r6
+ beq clear_bss
+
+#ifndef CONFIG_SKIP_RELOCATE_UBOOT
+copy_loop:
+ ldmia r0!, {r9-r10} /* copy from source address [r0] */
+ stmia r6!, {r9-r10} /* copy to target address [r1] */
+ cmp r0, r2 /* until source end addreee [r2] */
+ ble copy_loop
+
+#ifndef CONFIG_PRELOADER
+ /* fix got entries */
+ ldr r1, _TEXT_BASE /* Text base */
+ mov r0, r7 /* reloc addr */
+ ldr r2, _got_start /* addr in Flash */
+ ldr r3, _got_end /* addr in Flash */
+ sub r3, r3, r1
+ add r3, r3, r0
+ sub r2, r2, r1
+ add r2, r2, r0
+
+fixloop:
+ ldr r4, [r2]
+ sub r4, r4, r1
+ add r4, r4, r0
+ str r4, [r2]
+ add r2, r2, #4
+ cmp r2, r3
+ bne fixloop
+#endif
+#endif /* #ifndef CONFIG_SKIP_RELOCATE_UBOOT */
+
+#ifdef CONFIG_ENABLE_MMU
+enable_mmu:
+ /* enable domain access */
+ ldr r5, =0x0000ffff
+ mcr p15, 0, r5, c3, c0, 0 /* load domain access register */
+
+ /* Set the TTB register */
+ ldr r0, _mmu_table_base
+ ldr r1, =CONFIG_SYS_PHY_UBOOT_BASE
+ ldr r2, =0xfff00000
+ bic r0, r0, r2
+ orr r1, r0, r1
+ mcr p15, 0, r1, c2, c0, 0
+
+ /* Enable the MMU */
+ mrc p15, 0, r0, c1, c0, 0
+ orr r0, r0, #1 /* Set CR_M to enable MMU */
+
+ /* Prepare to enable the MMU */
+ adr r1, skip_hw_init
+ and r1, r1, #0x3fc
+ ldr r2, _TEXT_BASE
+ ldr r3, =0xfff00000
+ and r2, r2, r3
+ orr r2, r2, r1
+ b mmu_enable
+
+ .align 5
+ /* Run in a single cache-line */
+mmu_enable:
+
+ mcr p15, 0, r0, c1, c0, 0
+ nop
+ nop
+ mov pc, r2
+skip_hw_init:
+#endif
+
+clear_bss:
+#ifndef CONFIG_PRELOADER
+ ldr r0, _bss_start
+ ldr r1, _bss_end
+ ldr r3, _TEXT_BASE /* Text base */
+ mov r4, r7 /* reloc addr */
+ sub r0, r0, r3
+ add r0, r0, r4
+ sub r1, r1, r3
+ add r1, r1, r4
+ mov r2, #0x00000000 /* clear */
+
+clbss_l:str r2, [r0] /* clear loop... */
+ add r0, r0, #4
+ cmp r0, r1
+ bne clbss_l
+
+ bl coloured_LED_init
+ bl red_LED_on
+#endif
+
+/*
+ * We are done. Do not return, instead branch to second part of board
+ * initialization, now running from RAM.
+ */
+#ifdef CONFIG_NAND_SPL
+ ldr pc, _nand_boot
+
+_nand_boot: .word nand_boot
+#else
+ ldr r0, _TEXT_BASE
+ ldr r2, _board_init_r
+ sub r2, r2, r0
+ add r2, r2, r7 /* position from board_init_r in RAM */
+ /* setup parameters for board_init_r */
+ mov r0, r5 /* gd_t */
+ mov r1, r7 /* dest_addr */
+ /* jump to it ... */
+ mov lr, r2
+ mov pc, lr
+
+_board_init_r: .word board_init_r
+#endif
+
+#else /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
+
/*
* the actual reset code
*/
/* .word nand_boot*/
#endif
+#endif /* #if !defined(CONFIG_SYS_ARM_WITHOUT_RELOC) */
+
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
/* Save user registers (now in svc mode) r0-r12 */
stmia sp, {r0 - r12}
+#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
ldr r2, _armboot_start
sub r2, r2, #(CONFIG_SYS_MALLOC_LEN)
/* set base 2 words into abort stack */
sub r2, r2, #(CONFIG_SYS_GBL_DATA_SIZE+8)
+#else
+ ldr r2, IRQ_STACK_START_IN
+#endif
/* get values for "aborted" pc and cpsr (into parm regs) */
ldmia r2, {r2 - r3}
/* grab pointer to old stack */
.endm
.macro get_bad_stack
+#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* setup our mode stack (enter in banked mode) */
ldr r13, _armboot_start
/* move past malloc pool */
sub r13, r13, #(CONFIG_SYS_MALLOC_LEN)
/* move to reserved a couple spots for abort stack */
sub r13, r13, #(CONFIG_SYS_GBL_DATA_SIZE + 8)
+#else
+ ldr r13, IRQ_STACK_START_IN @ setup our mode stack
+#endif
/* save caller lr in position 0 of saved stack */
str lr, [r13]
sub r13, r13, #4
/* save R0's value. */
str r0, [r13]
+#if defined(CONFIG_SYS_ARM_WITHOUT_RELOC)
/* get data regions start */
ldr r0, _armboot_start
/* move past malloc pool */
sub r0, r0, #(CONFIG_SYS_MALLOC_LEN)
/* move past gbl and a couple spots for abort stack */
sub r0, r0, #(CONFIG_SYS_GBL_DATA_SIZE + 8)
+#else
+ ldr r13, IRQ_STACK_START_IN @ setup our mode stack
+#endif
/* save caller lr in position 0 of saved stack */
str lr, [r0]
/* get the spsr */
projects / u-boot.git / commitdiff
