mx6qsabresd: Add Ethernet support

mx6qsabresd has a AR8031 Gigabit PHY.

Add support for it.

Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail.

Tested on 1Gbp and 100Mbps networks.

Suggested-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>

diff --git a/board/freescale/mx6qsabresd/mx6qsabresd.c b/board/freescale/mx6qsabresd/mx6qsabresd.c
index c86b51b4cadb626bd90a7b5337ac0c890a6cc518..069c66417bd152900b981c99e2e341879433bc29 100644 (file)
--- a/board/freescale/mx6qsabresd/mx6qsabresd.c
+++ b/board/freescale/mx6qsabresd/mx6qsabresd.c
@@ -56,6 +56,36 @@ iomux_v3_cfg_t uart1_pads[] = {
        MX6Q_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+iomux_v3_cfg_t enet_pads[] = {
+       MX6Q_PAD_ENET_MDIO__ENET_MDIO           | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_ENET_MDC__ENET_MDC             | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL     | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3      | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL     | MUX_PAD_CTRL(ENET_PAD_CTRL),
+       /* AR8031 PHY Reset */
+       MX6Q_PAD_ENET_CRS_DV__GPIO_1_25         | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+       imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+       /* Reset AR8031 PHY */
+       gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
+       udelay(500);
+       gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+}
+
 iomux_v3_cfg_t usdhc3_pads[] = {
        MX6Q_PAD_SD3_CLK__USDHC3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
        MX6Q_PAD_SD3_CMD__USDHC3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -90,6 +120,52 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+       unsigned short val;
+
+       /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
+       phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+       phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+       phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+       val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+       val &= 0xffe3;
+       val |= 0x18;
+       phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+       /* introduce tx clock delay */
+       phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+       val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+       val |= 0x0100;
+       phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+       return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+       mx6_rgmii_rework(phydev);
+
+       if (phydev->drv->config)
+               phydev->drv->config(phydev);
+
+       return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+       int ret;
+
+       setup_iomux_enet();
+
+       ret = cpu_eth_init(bis);
+       if (ret)
+               printf("FEC MXC: %s:failed\n", __func__);
+
+       return 0;
+}
+
 u32 get_board_rev(void)
 {
        return 0x63000;

diff --git a/include/configs/mx6qsabresd.h b/include/configs/mx6qsabresd.h
index 448ce287583e36ee2cac67b98290baf7db4ac80a..a2d2c65f198a0a950ece51d9ff4ce3b262e6f3e3 100644 (file)
--- a/include/configs/mx6qsabresd.h
+++ b/include/configs/mx6qsabresd.h
@@ -33,9 +33,8 @@
 #define CONFIG_REVISION_TAG
 
 /* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN          CONFIG_ENV_SIZE
+#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
 
-#define CONFIG_ARCH_CPU_INIT
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_MXC_GPIO
 
@@ -55,6 +54,20 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE                   ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE            RGMII
+#define CONFIG_ETHPRIME                        "FEC"
+#define CONFIG_FEC_MXC_PHYADDR         1
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX              1