imx7: SPI: add suport for SPI flash in mikroBUS slot

Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.

This is V2 of this patch with changes recommended by the maintainer

CC: Jagan Teki <jteki@openedev.com>

diff --git a/board/freescale/mx7dsabresd/mx7dsabresd.c b/board/freescale/mx7dsabresd/mx7dsabresd.c
index b9365445e85edb747a7a00ecc612b3785cd5f679..6ccdd4b33b223e44bcd693572bdeb2e39205b8bd 100644 (file)
--- a/board/freescale/mx7dsabresd/mx7dsabresd.c
+++ b/board/freescale/mx7dsabresd/mx7dsabresd.c
@@ -50,6 +50,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
 
+#define SPI_PAD_CTRL \
+  (PAD_CTL_HYS | PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_FAST)
+
 #define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
 #ifdef CONFIG_SYS_I2C_MXC
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
@@ -68,6 +71,23 @@ static struct i2c_pads_info i2c_pad_info1 = {
 };
 #endif
 
+static iomux_v3_cfg_t const ecspi3_pads[] = {
+    MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+    MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+    MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+    MX7D_PAD_SAI2_TX_DATA__GPIO6_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+         return (bus == 2 && cs == 0) ? (IMX_GPIO_NR(6, 22)) : -1;
+}
+
+static void setup_spi(void)
+{
+         imx_iomux_v3_setup_multiple_pads(ecspi3_pads, ARRAY_SIZE(ecspi3_pads));
+}
+
 int dram_init(void)
 {
        gd->ram_size = PHYS_SDRAM_SIZE;
@@ -553,6 +573,10 @@ int board_init(void)
        board_qspi_init();
 #endif
 
+#ifdef CONFIG_MXC_SPI
+       setup_spi();
+#endif
+
        return 0;
 }
 

diff --git a/configs/mx7dsabresd_secure_defconfig b/configs/mx7dsabresd_secure_defconfig
index 126ce31ff73ed3b2417d13e21db29b72bbf5a42d..ef935221c48b26f4796896e23b40ea4813817b9c 100644 (file)
--- a/configs/mx7dsabresd_secure_defconfig
+++ b/configs/mx7dsabresd_secure_defconfig
@@ -45,3 +45,6 @@ CONFIG_G_DNL_MANUFACTURER="FSL"
 CONFIG_G_DNL_VENDOR_NUM=0x0525
 CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
 CONFIG_OF_LIBFDT=y
+CONFIG_SPI_FLASH=y
+CONFIG_CMD_SF=y
+CONFIG_SPI_FLASH_EON=y

diff --git a/include/configs/mx7dsabresd.h b/include/configs/mx7dsabresd.h
index 360a5e0d9c59017f17036444dc1a440284a55380..ca5f9db568b9a3680f2795c6b6ef9e8c1cc97a45 100644 (file)
--- a/include/configs/mx7dsabresd.h
+++ b/include/configs/mx7dsabresd.h
@@ -201,6 +201,9 @@
 #define CONFIG_ENV_SIZE                        SZ_8K
 #define CONFIG_ENV_IS_IN_MMC
 
+/* MXC SPI driver support */
+#define CONFIG_MXC_SPI
+
 /*
  * If want to use nand, define CONFIG_NAND_MXS and rework board
  * to support nand, since emmc has pin conflicts with nand