*/
#include <common.h>
+#include <dm.h>
#include <linux/list.h>
-#include <asm/gpio.h>
#include <asm/arch/iomux-mx53.h>
+#include <asm/mach-imx/video.h>
#include <linux/fb.h>
#include <ipu_pixfmt.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
#include <asm/io.h>
-#include <pwm.h>
-#include "ppd_gpio.h"
+#include <panel.h>
-#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
-
-static struct fb_videomode const nv_spwg = {
- .name = "NV-SPWGRGB888",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 15384,
- .left_margin = 16,
- .right_margin = 210,
- .upper_margin = 10,
- .lower_margin = 22,
- .hsync_len = 30,
- .vsync_len = 13,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-};
-
-void setup_iomux_lcd(void)
+static int detect_lcd(struct display_info_t const *dev)
{
- static const iomux_v3_cfg_t lcd_pads[] = {
- MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
- MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
- MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
- MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
- MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
- MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
- MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
- MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
- MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
- MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
- MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
- MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
- MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
- MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
- MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
- MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
- MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
- MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
- MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
- MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
- MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
- MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
- MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
- MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
- MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
- MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
- MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
- MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
- };
-
- imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+ return 1;
}
static void lcd_enable(void)
IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
&iomux->gpr[2]);
-
- /* Enable backlights */
- pwm_init(1, 0, 0);
-
- /* duty cycle 5000000ns, period: 5000000ns */
- pwm_config(1, 5000000, 5000000);
-
- /* Backlight Power */
- gpio_request(BACKLIGHT_ENABLE, "BACKLIGHT_ENABLE");
- gpio_direction_output(BACKLIGHT_ENABLE, 1);
-
- pwm_enable(1);
}
-static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
- char * const argv[])
+static void do_enable_backlight(struct display_info_t const *dev)
{
+ struct udevice *panel;
+ int ret;
+
lcd_enable();
- return 0;
-}
-U_BOOT_CMD(
- ppd_lcd_enable, 1, 1, do_lcd_enable,
- "enable PPD LCD",
- "no parameters"
-);
+ ret = uclass_get_device(UCLASS_PANEL, 0, &panel);
+ if (ret) {
+ printf("Could not find panel: %d\n", ret);
+ return;
+ }
-int board_video_skip(void)
-{
- int ret;
+ panel_set_backlight(panel, 100);
+ panel_enable_backlight(panel);
+}
+
+struct display_info_t const displays[] = {
+ {
+ .bus = -1,
+ .addr = -1,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_lcd,
+ .enable = do_enable_backlight,
+ .mode = {
+ .name = "NV-SPWGRGB888",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 15384,
+ .left_margin = 16,
+ .right_margin = 210,
+ .upper_margin = 10,
+ .lower_margin = 22,
+ .hsync_len = 30,
+ .vsync_len = 13,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+ }
+ }
+};
- ret = ipuv3_fb_init(&nv_spwg, 0, IPU_PIX_FMT_RGB24);
- if (ret)
- printf("Display cannot be configured: %d\n", ret);
+size_t display_count = ARRAY_SIZE(displays);
- return ret;
-}
#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
-#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
{ POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
{ POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
{ ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
- { BACKLIGHT_ENABLE, 0 },
{ RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
{ ECSPI1_CS0, 1 },
{ ECSPI1_CS1, 1 },
projects / u-boot.git / commitdiff
