--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2019 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "sun8i-v3.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "PineCube IP Camera";
+ compatible = "pine64,pinecube", "allwinner,sun8i-s3";
+
+ aliases {
+ serial0 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ label = "pine64:ir:led1";
+ gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
+ };
+
+ led2 {
+ label = "pine64:ir:led2";
+ gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */
+ };
+ };
+
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_vcc_wifi: vcc-wifi {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-wifi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */
+ vin-supply = <®_dcdc3>;
+ startup-delay-us = <200000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&csi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&csi1_8bit_pins>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi1_ep: endpoint {
+ remote-endpoint = <&ov5640_ep>;
+ bus-width = <8>;
+ hsync-active = <1>; /* Active high */
+ vsync-active = <0>; /* Active low */
+ data-active = <1>; /* Active high */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp203",
+ "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pe_pins>;
+ status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&csi1_mclk_pin>;
+ clocks = <&ccu CLK_CSI1_MCLK>;
+ clock-names = "xclk";
+
+ AVDD-supply = <®_ldo3>;
+ DOVDD-supply = <®_ldo3>;
+ DVDD-supply = <®_ldo4>;
+ reset-gpios = <&pio 4 23 GPIO_ACTIVE_LOW>; /* PE23 */
+ powerdown-gpios = <&pio 4 24 GPIO_ACTIVE_HIGH>; /* PE24 */
+
+ port {
+ ov5640_ep: endpoint {
+ remote-endpoint = <&csi1_ep>;
+ bus-width = <8>;
+ hsync-active = <1>; /* Active high */
+ vsync-active = <0>; /* Active low */
+ data-active = <1>; /* Active high */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button-200 {
+ label = "Setup";
+ linux,code = <KEY_SETUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc_wifi>;
+ vqmmc-supply = <®_dcdc3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ vcc-pd-supply = <®_dcdc3>;
+ vcc-pe-supply = <®_ldo3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd-sys-cpu-ephy";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-dovdd-2v8-csi";
+ regulator-soft-start;
+ regulator-ramp-delay = <1600>;
+};
+
+®_ldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-1v8-csi";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "winbond,w25q128", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_vcc5v0>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun8i-v3s-licheepi-zero.dts"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Lichee Pi Zero with Dock";
+ compatible = "licheepi,licheepi-zero-dock", "licheepi,licheepi-zero",
+ "allwinner,sun8i-v3s";
+
+ leds {
+ /* The LEDs use PG0~2 pins, which conflict with MMC1 */
+ status = "disabled";
+ };
+};
+
+&mmc1 {
+ broken-cd;
+ bus-width = <4>;
+ vmmc-supply = <®_vcc3v3>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button-200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button-400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+
+ button-600 {
+ label = "Select";
+ linux,code = <KEY_SELECT>;
+ channel = <0>;
+ voltage = <600000>;
+ };
+
+ button-800 {
+ label = "Start";
+ linux,code = <KEY_OK>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+};
* OTHER DEALINGS IN THE SOFTWARE.
*/
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/sun8i-v3s-ccu.h>
#include <dt-bindings/reset/sun8i-v3s-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/clock/sun8i-de2.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&gic>;
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer-lcd {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer0-lcd0";
+ clocks = <&display_clocks CLK_MIXER0>,
+ <&ccu CLK_TCON0>;
+ status = "disabled";
+ };
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
};
};
+ de: display-engine {
+ compatible = "allwinner,sun8i-v3s-display-engine";
+ allwinner,pipelines = <&mixer0>;
+ status = "disabled";
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-accuracy = <50000>;
+ clock-output-names = "ext-osc32k";
};
};
#size-cells = <1>;
ranges;
- mmc0: mmc@01c0f000 {
+ display_clocks: clock@1000000 {
+ compatible = "allwinner,sun8i-v3s-de2-clk";
+ reg = <0x01000000 0x10000>;
+ clocks = <&ccu CLK_BUS_DE>,
+ <&ccu CLK_DE>;
+ clock-names = "bus",
+ "mod";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@1100000 {
+ compatible = "allwinner,sun8i-v3s-de2-mixer";
+ reg = <0x01100000 0x100000>;
+ clocks = <&display_clocks 0>,
+ <&display_clocks 6>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ syscon: system-control@1c00000 {
+ compatible = "allwinner,sun8i-v3s-system-control",
+ "allwinner,sun8i-h3-system-control";
+ reg = <0x01c00000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ };
+
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun8i-v3s-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>,
+ <&ccu CLK_TCON0>;
+ clock-names = "ahb",
+ "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ #clock-cells = <0>;
+ resets = <&ccu RST_BUS_TCON0>;
+ reset-names = "lcd";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint {
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+
+ mmc0: mmc@1c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>,
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc1: mmc@01c10000 {
+ mmc1: mmc@1c10000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>,
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
- mmc2: mmc@01c11000 {
+ mmc2: mmc@1c11000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>,
#size-cells = <0>;
};
- usb_otg: usb@01c19000 {
+ crypto@1c15000 {
+ compatible = "allwinner,sun8i-v3s-crypto",
+ "allwinner,sun8i-a33-crypto";
+ reg = <0x01c15000 0x1000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_CE>;
+ reset-names = "ahb";
+ };
+
+ usb_otg: usb@1c19000 {
compatible = "allwinner,sun8i-h3-musb";
reg = <0x01c19000 0x0400>;
clocks = <&ccu CLK_BUS_OTG>;
status = "disabled";
};
- usbphy: phy@01c19400 {
+ usbphy: phy@1c19400 {
compatible = "allwinner,sun8i-v3s-usb-phy";
reg = <0x01c19400 0x2c>,
<0x01c1a800 0x4>;
#phy-cells = <1>;
};
- ccu: clock@01c20000 {
+ ccu: clock@1c20000 {
compatible = "allwinner,sun8i-v3s-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
- rtc: rtc@01c20400 {
- compatible = "allwinner,sun6i-a31-rtc";
+ rtc: rtc@1c20400 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-v3-rtc";
reg = <0x01c20400 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k", "osc32k-out";
};
- pio: pinctrl@01c20800 {
+ pio: pinctrl@1c20800 {
compatible = "allwinner,sun8i-v3s-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
- uart0_pins_a: uart0@0 {
+ /omit-if-no-ref/
+ csi1_8bit_pins: csi1-8bit-pins {
+ pins = "PE0", "PE2", "PE3", "PE8", "PE9",
+ "PE10", "PE11", "PE12", "PE13", "PE14",
+ "PE15";
+ function = "csi";
+ };
+
+ /omit-if-no-ref/
+ csi1_mclk_pin: csi1-mclk-pin {
+ pins = "PE1";
+ function = "csi";
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PB6", "PB7";
+ function = "i2c0";
+ };
+
+ /omit-if-no-ref/
+ i2c1_pe_pins: i2c1-pe-pins {
+ pins = "PE21", "PE22";
+ function = "i2c1";
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB8", "PB9";
function = "uart0";
- bias-pull-up;
};
- mmc0_pins_a: mmc0@0 {
+ uart2_pins: uart2-pins {
+ pins = "PB0", "PB1";
+ function = "uart2";
+ };
+
+ mmc0_pins: mmc0-pins {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
+
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0-pins {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
};
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
+ timer@1c20c00 {
+ compatible = "allwinner,sun8i-v3s-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
- wdt0: watchdog@01c20ca0 {
+ wdt0: watchdog@1c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ lradc: lradc@1c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x400>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
};
- uart0: serial@01c28000 {
+ uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- uart1: serial@01c28400 {
+ uart1: serial@1c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- uart2: serial@01c28800 {
+ uart2: serial@1c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART2>;
resets = <&ccu RST_BUS_UART2>;
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun8i-v3s-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+
+ mdio_mux: mdio-mux {
+ compatible = "allwinner,sun8i-h3-mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio-parent-bus = <&mdio>;
+ /* Only one MDIO is usable at the time */
+ internal_mdio: mdio@1 {
+ compatible = "allwinner,sun8i-h3-mdio-internal";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ int_mii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+ };
+ };
+
+ spi0: spi@1c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ csi1: camera@1cb4000 {
+ compatible = "allwinner,sun8i-v3s-csi";
+ reg = <0x01cb4000 0x3000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CSI>,
+ <&ccu CLK_CSI1_SCLK>,
+ <&ccu CLK_DRAM_CSI>;
+ clock-names = "bus", "mod", "ram";
+ resets = <&ccu RST_BUS_CSI>;
status = "disabled";
};
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x1000>,
<0x01c84000 0x2000>,
projects / u-boot.git / commitdiff
