config TARGET_CPCI2DP
bool "Support CPCI2DP"
-config TARGET_CPCI405
- bool "Support CPCI405"
-
config TARGET_CPCI4052
bool "Support CPCI4052"
-config TARGET_CPCI405AB
- bool "Support CPCI405AB"
-
-config TARGET_CPCI405DT
- bool "Support CPCI405DT"
-
config TARGET_PLU405
bool "Support PLU405"
-if TARGET_CPCI405
-
-config SYS_BOARD
- default "cpci405"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "CPCI405"
-
-endif
-
if TARGET_CPCI4052
config SYS_BOARD
default "CPCI4052"
endif
-
-if TARGET_CPCI405AB
-
-config SYS_BOARD
- default "cpci405"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "CPCI405AB"
-
-endif
-
-if TARGET_CPCI405DT
-
-config SYS_BOARD
- default "cpci405"
-
-config SYS_VENDOR
- default "esd"
-
-config SYS_CONFIG_NAME
- default "CPCI405DT"
-
-endif
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CPCI405AB=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CPCI405DT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CPCI405=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+CPCI405 ppc4xx 405gp - - Matthias Fuchs <matthias.fuchs@esd.eu>
+CPCI405DT ppc4xx 405gpr - - Matthias Fuchs <matthias.fuchs@esd.eu>
+CPCI405AB ppc4xx 405gpr - - Matthias Fuchs <matthias.fuchs@esd.eu>
G2000 ppc4xx 405ep - - Matthias Fuchs <matthias.fuchs@esd.eu>
WUH405 ppc4xx 405ep - - Matthias Fuchs <matthias.fuchs@esd.eu>
VOH405 ppc4xx 405ep - - Matthias Fuchs <matthias.fuchs@esd.eu>
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#undef CONFIG_BOOTARGS
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT /* enable preboot variable */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
-
-#undef CONFIG_HAS_ETH1
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_EEPROM
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_LOOPW 1 /* enable loopw command */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
-
-#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
-
-#if 1 /* Use NVRAM for environment variables */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
-
-#else /* Use EEPROM for environment variables */
-
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
- /* total size of a CAT24WC08 is 1024 bytes */
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC08) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (NVRAM) initialization */
-#define CONFIG_SYS_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 5 (Quart) initialization */
-#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-#if 1 /* test-only */
-#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2001-2003
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
-#define CONFIG_CPCI405AB 1 /* ...and special AB version */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#undef CONFIG_BOOTARGS
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT /* enable preboot variable */
-
-#undef CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
-
-#undef CONFIG_HAS_ETH1
-
-#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_EEPROM
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_CMDLINE_EDITING /* add command line history */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT \
- "Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_AUTOBOOT_STOP_STR " "
-
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
-
-#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-#define CONFIG_PRAM 0 /* use pram variable to overwrite */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC32) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */
- /* 32 byte page write mode using*/
- /* last 5 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/* Use EEPROM for environment variables */
-
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
- /* total size of a CAT24WC32 is 4096 bytes */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CONFIG_SYS_LED_ADDR 0xF0000380
-
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (NVRAM/RTC) initialization */
-/*#define CONFIG_SYS_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CONFIG_SYS_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
-#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 5 (optional Quart) initialization */
-#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 6 (FPGA internal) initialization */
-#define CONFIG_SYS_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_MODE 0x00
-#define CONFIG_SYS_FPGA_STATUS 0x02
-#define CONFIG_SYS_FPGA_TS 0x04
-#define CONFIG_SYS_FPGA_TS_LOW 0x06
-#define CONFIG_SYS_FPGA_TS_CAP0 0x10
-#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
-#define CONFIG_SYS_FPGA_TS_CAP1 0x14
-#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
-#define CONFIG_SYS_FPGA_TS_CAP2 0x18
-#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
-#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
-#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
-
-/* FPGA Mode Reg */
-#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
-#define CONFIG_SYS_FPGA_MODE_DUART_RESET 0x0002
-#define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
-#define CONFIG_SYS_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */
-#define CONFIG_SYS_FPGA_MODE_SIM_OK_DIR 0x0200
-#define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400
-#define CONFIG_SYS_FPGA_MODE_1WIRE 0x1000
-#define CONFIG_SYS_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */
-#define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL 0x4000
-
-/* FPGA Status Reg */
-#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
-#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
-#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
-#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
-#define CONFIG_SYS_FPGA_STATUS_1WIRE 0x1000
-#define CONFIG_SYS_FPGA_STATUS_SIM_OK 0x2000
-
-#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2001-2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405 CPU */
-#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
-#define CONFIG_CPCI405_VER2 1 /* ...version 2 */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#undef CONFIG_BOOTARGS
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_PREBOOT /* enable preboot variable */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
-
-#undef CONFIG_HAS_ETH1
-
-#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_EEPROM
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#undef CONFIG_AUTO_UPDATE /* autoupdate via compactflash */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_LOOPW 1 /* enable loopw command */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/* Only interrupt boot if special string is typed */
-#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT \
- "Autobooting in %d seconds\n", bootdelay
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#undef CONFIG_AUTOBOOT_STOP_STR /* defined via environment var */
-#define CONFIG_AUTOBOOT_STOP_STR2 "esdesd" /* esd special for esd access*/
-
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
-
-#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#if 0 /* Use NVRAM for environment variables */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-(CONFIG_ENV_SIZE+8)) /* Env */
-
-#else /* Use EEPROM for environment variables */
-
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
- /* total size of a CAT24WC16 is 2048 bytes */
-#endif
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
-#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (Flash Bank 1) initialization */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 2 (CAN0, 1) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-#define CONFIG_SYS_LED_ADDR 0xF0000380
-
-/* Memory Bank 3 (CompactFlash IDE) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (NVRAM/RTC) initialization */
-/*#define CONFIG_SYS_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */
-#define CONFIG_SYS_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */
-#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 5 (optional Quart) initialization */
-#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 6 (FPGA internal) initialization */
-#define CONFIG_SYS_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_MODE 0x00
-#define CONFIG_SYS_FPGA_STATUS 0x02
-#define CONFIG_SYS_FPGA_TS 0x04
-#define CONFIG_SYS_FPGA_TS_LOW 0x06
-#define CONFIG_SYS_FPGA_TS_CAP0 0x10
-#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
-#define CONFIG_SYS_FPGA_TS_CAP1 0x14
-#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
-#define CONFIG_SYS_FPGA_TS_CAP2 0x18
-#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
-#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
-#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
-
-/* FPGA Mode Reg */
-#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
-#define CONFIG_SYS_FPGA_MODE_DUART_RESET 0x0002
-#define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
-
-/* FPGA Status Reg */
-#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
-#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
-#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
-#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
-#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
-
-#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff
