u-boot.sb: u-boot.bin spl/u-boot-spl.bin
$(Q)$(MAKE) $(build)=arch/arm/cpu/arm926ejs/mxs u-boot.sb
-# On x600 (SPEAr600) U-Boot is appended to U-Boot SPL.
-# Both images are created using mkimage (crc etc), so that the ROM
-# bootloader can check its integrity. Padding needs to be done to the
-# SPL image (with mkimage header) and not the binary. Otherwise the resulting image
-# which is loaded/copied by the ROM bootloader to SRAM doesn't fit.
-# The resulting image containing both U-Boot images is called u-boot.spr
MKIMAGEFLAGS_u-boot-spl.img = -A $(ARCH) -T firmware -C none \
-a $(CONFIG_SPL_TEXT_BASE) -e $(CONFIG_SPL_TEXT_BASE) -n XLOADER
spl/u-boot-spl.img: spl/u-boot-spl.bin FORCE
$(call if_changed,mkimage)
-OBJCOPYFLAGS_u-boot.spr = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) \
- --gap-fill=0xff
-u-boot.spr: spl/u-boot-spl.img u-boot.img FORCE
- $(call if_changed,pad_cat)
-
ifneq ($(CONFIG_ARCH_SOCFPGA),)
quiet_cmd_gensplx4 = GENSPLX4 $@
cmd_gensplx4 = $(OBJCOPY) -I binary -O binary --gap-fill=0x0 \
select CPU_ARM926EJS
select GPIO_EXTRA_HEADER
-config TARGET_SPEAR600
- bool "Support spear600"
- select BOARD_EARLY_INIT_F
- select CPU_ARM926EJS
- select GPIO_EXTRA_HEADER
- select PL011_SERIAL
- imply CMD_SAVES
-
config TARGET_STV0991
bool "Support stv0991"
select CPU_V7A
select SPI_FLASH
imply CMD_DM
-config TARGET_X600
- bool "Support x600"
- select BOARD_LATE_INIT
- select CPU_ARM926EJS
- select GPIO_EXTRA_HEADER
- select PL011_SERIAL
- select SUPPORT_SPL
-
config TARGET_FLEA3
bool "Support flea3"
select CPU_ARM1136
source "board/myir/mys_6ulx/Kconfig"
source "board/seeed/npi_imx6ull/Kconfig"
source "board/socionext/developerbox/Kconfig"
-source "board/spear/spear600/Kconfig"
-source "board/spear/x600/Kconfig"
source "board/st/stv0991/Kconfig"
source "board/tcl/sl50/Kconfig"
source "board/toradex/colibri_pxa270/Kconfig"
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y := cpu.o \
- reset.o \
- timer.o
-
-ifdef CONFIG_SPL_BUILD
-obj-y += spl.o
-obj-$(CONFIG_SPEAR600) += spear600.o
-obj-$(CONFIG_DDR_MT47H64M16) += spr600_mt47h64m16_3_333_cl5_psync.o
-obj-$(CONFIG_DDR_MT47H32M16) += spr600_mt47h32m16_333_cl5_psync.o
-obj-$(CONFIG_DDR_MT47H32M16) += spr600_mt47h32m16_37e_166_cl4_sync.o
-obj-$(CONFIG_DDR_MT47H128M8) += spr600_mt47h128m8_3_266_cl5_async.o
-else
-obj-y += spr_misc.o spr_lowlevel_init.o
-endif
-
-extra-$(CONFIG_SPL_BUILD) := start.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_misc.h>
-
-int arch_cpu_init(void)
-{
- struct misc_regs *const misc_p =
- (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 periph1_clken, periph_clk_cfg;
-
- periph1_clken = readl(&misc_p->periph1_clken);
-
-#if defined(CONFIG_SPEAR600)
- periph1_clken |= MISC_GPT3ENB;
-#endif
-
-#if defined(CONFIG_PL011_SERIAL)
- periph1_clken |= MISC_UART0ENB;
-
- periph_clk_cfg = readl(&misc_p->periph_clk_cfg);
- periph_clk_cfg &= ~CONFIG_SPEAR_UARTCLKMSK;
- periph_clk_cfg |= CONFIG_SPEAR_UART48M;
- writel(periph_clk_cfg, &misc_p->periph_clk_cfg);
-#endif
-#if defined(CONFIG_ETH_DESIGNWARE)
- periph1_clken |= MISC_ETHENB;
-#endif
-#if defined(CONFIG_DW_UDC)
- periph1_clken |= MISC_USBDENB;
-#endif
-#if defined(CONFIG_SYS_I2C_DW)
- periph1_clken |= MISC_I2CENB;
-#endif
-#if defined(CONFIG_ST_SMI)
- periph1_clken |= MISC_SMIENB;
-#endif
-#if defined(CONFIG_NAND_FSMC)
- periph1_clken |= MISC_FSMCENB;
-#endif
-#if defined(CONFIG_USB_EHCI_SPEAR)
- periph1_clken |= PERIPH_USBH1 | PERIPH_USBH2;
-#endif
-#if defined(CONFIG_SPEAR_GPIO)
- periph1_clken |= MISC_GPIO3ENB | MISC_GPIO4ENB;
-#endif
-#if defined(CONFIG_PL022_SPI)
- periph1_clken |= MISC_SSP1ENB | MISC_SSP2ENB | MISC_SSP3ENB;
-#endif
-
- writel(periph1_clken, &misc_p->periph1_clken);
-
- return 0;
-}
-
-#ifdef CONFIG_DISPLAY_CPUINFO
-int print_cpuinfo(void)
-{
-#if defined(CONFIG_SPEAR600)
- printf("CPU: SPEAr600\n");
-#else
-#error CPU not supported in spear platform
-#endif
- return 0;
-}
-#endif
-
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_ECC_BCH) && defined(CONFIG_NAND_FSMC)
-static int do_switch_ecc(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- if (argc != 2)
- goto usage;
-
- if (strncmp(argv[1], "hw", 2) == 0) {
- /* 1-bit HW ECC */
- printf("Switching to 1-bit HW ECC\n");
- fsmc_nand_switch_ecc(1);
- } else if (strncmp(argv[1], "bch4", 2) == 0) {
- /* 4-bit SW ECC BCH4 */
- printf("Switching to 4-bit SW ECC (BCH4)\n");
- fsmc_nand_switch_ecc(4);
- } else {
- goto usage;
- }
-
- return 0;
-
-usage:
- printf("Usage: nandecc %s\n", cmdtp->usage);
- return 1;
-}
-
-U_BOOT_CMD(
- nandecc, 2, 0, do_switch_ecc,
- "switch NAND ECC calculation algorithm",
- "hw|bch4 - Switch between NAND hardware 1-bit HW and"
- " 4-bit SW BCH\n"
-);
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <cpu_func.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_syscntl.h>
-#include <linux/delay.h>
-
-void reset_cpu(void)
-{
- struct syscntl_regs *syscntl_regs_p =
- (struct syscntl_regs *)CONFIG_SPEAR_SYSCNTLBASE;
-
- printf("System is going to reboot ...\n");
-
- /*
- * This 1 second delay will allow the above message
- * to be printed before reset
- */
- udelay((1000 * 1000));
-
- /* Going into slow mode before resetting SOC */
- writel(0x02, &syscntl_regs_p->scctrl);
-
- /*
- * Writing any value to the system status register will
- * reset the SoC
- */
- writel(0x00, &syscntl_regs_p->scsysstat);
-
- /* system will restart */
- while (1)
- ;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2009
- * Viresh Kumar, ST Microelectronics, viresh.kumar@st.com
- * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com
- */
-
-#include <common.h>
-#include <asm/hardware.h>
-#include <asm/io.h>
-#include <asm/arch/spr_misc.h>
-#include <asm/arch/spr_defs.h>
-
-void spear_late_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
- writel(0x80000007, &misc_p->arb_icm_ml1);
- writel(0x80000007, &misc_p->arb_icm_ml2);
- writel(0x80000007, &misc_p->arb_icm_ml3);
- writel(0x80000007, &misc_p->arb_icm_ml4);
- writel(0x80000007, &misc_p->arb_icm_ml5);
- writel(0x80000007, &misc_p->arb_icm_ml6);
- writel(0x80000007, &misc_p->arb_icm_ml7);
- writel(0x80000007, &misc_p->arb_icm_ml8);
- writel(0x80000007, &misc_p->arb_icm_ml9);
-}
-
-static void sel_1v8(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 ddr1v8, ddr2v5;
-
- ddr2v5 = readl(&misc_p->ddr_2v5_compensation);
- ddr2v5 &= 0x8080ffc0;
- ddr2v5 |= 0x78000003;
- writel(ddr2v5, &misc_p->ddr_2v5_compensation);
-
- ddr1v8 = readl(&misc_p->ddr_1v8_compensation);
- ddr1v8 &= 0x8080ffc0;
- ddr1v8 |= 0x78000010;
- writel(ddr1v8, &misc_p->ddr_1v8_compensation);
-
- while (!(readl(&misc_p->ddr_1v8_compensation) & DDR_COMP_ACCURATE))
- ;
-}
-
-static void sel_2v5(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 ddr1v8, ddr2v5;
-
- ddr1v8 = readl(&misc_p->ddr_1v8_compensation);
- ddr1v8 &= 0x8080ffc0;
- ddr1v8 |= 0x78000003;
- writel(ddr1v8, &misc_p->ddr_1v8_compensation);
-
- ddr2v5 = readl(&misc_p->ddr_2v5_compensation);
- ddr2v5 &= 0x8080ffc0;
- ddr2v5 |= 0x78000010;
- writel(ddr2v5, &misc_p->ddr_2v5_compensation);
-
- while (!(readl(&misc_p->ddr_2v5_compensation) & DDR_COMP_ACCURATE))
- ;
-}
-
-/*
- * plat_ddr_init:
- */
-void plat_ddr_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 ddrpad;
- u32 core3v3, ddr1v8, ddr2v5;
-
- /* DDR pad register configurations */
- ddrpad = readl(&misc_p->ddr_pad);
- ddrpad &= ~DDR_PAD_CNF_MSK;
-
-#if (CONFIG_DDR_HCLK)
- ddrpad |= 0xEAAB;
-#elif (CONFIG_DDR_2HCLK)
- ddrpad |= 0xEAAD;
-#elif (CONFIG_DDR_PLL2)
- ddrpad |= 0xEAAD;
-#endif
- writel(ddrpad, &misc_p->ddr_pad);
-
- /* Compensation register configurations */
- core3v3 = readl(&misc_p->core_3v3_compensation);
- core3v3 &= 0x8080ffe0;
- core3v3 |= 0x78000002;
- writel(core3v3, &misc_p->core_3v3_compensation);
-
- ddr1v8 = readl(&misc_p->ddr_1v8_compensation);
- ddr1v8 &= 0x8080ffc0;
- ddr1v8 |= 0x78000004;
- writel(ddr1v8, &misc_p->ddr_1v8_compensation);
-
- ddr2v5 = readl(&misc_p->ddr_2v5_compensation);
- ddr2v5 &= 0x8080ffc0;
- ddr2v5 |= 0x78000004;
- writel(ddr2v5, &misc_p->ddr_2v5_compensation);
-
- if ((readl(&misc_p->ddr_pad) & DDR_PAD_SW_CONF) == DDR_PAD_SW_CONF) {
- /* Software memory configuration */
- if (readl(&misc_p->ddr_pad) & DDR_PAD_SSTL_SEL)
- sel_1v8();
- else
- sel_2v5();
- } else {
- /* Hardware memory configuration */
- if (readl(&misc_p->ddr_pad) & DDR_PAD_DRAM_TYPE)
- sel_1v8();
- else
- sel_2v5();
- }
-}
-
-/*
- * xxx_boot_selected:
- *
- * return true if the particular booting option is selected
- * return false otherwise
- */
-static u32 read_bootstrap(void)
-{
- return (readl(CONFIG_SPEAR_BOOTSTRAPCFG) >> CONFIG_SPEAR_BOOTSTRAPSHFT)
- & CONFIG_SPEAR_BOOTSTRAPMASK;
-}
-
-int snor_boot_selected(void)
-{
- u32 bootstrap = read_bootstrap();
-
- if (SNOR_BOOT_SUPPORTED) {
- /* Check whether SNOR boot is selected */
- if ((bootstrap & CONFIG_SPEAR_ONLYSNORBOOT) ==
- CONFIG_SPEAR_ONLYSNORBOOT)
- return true;
-
- if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) ==
- CONFIG_SPEAR_NORNAND8BOOT)
- return true;
-
- if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) ==
- CONFIG_SPEAR_NORNAND16BOOT)
- return true;
- }
-
- return false;
-}
-
-int nand_boot_selected(void)
-{
- u32 bootstrap = read_bootstrap();
-
- if (NAND_BOOT_SUPPORTED) {
- /* Check whether NAND boot is selected */
- if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) ==
- CONFIG_SPEAR_NORNAND8BOOT)
- return true;
-
- if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) ==
- CONFIG_SPEAR_NORNAND16BOOT)
- return true;
- }
-
- return false;
-}
-
-int pnor_boot_selected(void)
-{
- /* Parallel NOR boot is not selected in any SPEAr600 revision */
- return false;
-}
-
-int usb_boot_selected(void)
-{
- u32 bootstrap = read_bootstrap();
-
- if (USB_BOOT_SUPPORTED) {
- /* Check whether USB boot is selected */
- if (!(bootstrap & CONFIG_SPEAR_USBBOOT))
- return true;
- }
-
- return false;
-}
-
-int tftp_boot_selected(void)
-{
- /* TFTP boot is not selected in any SPEAr600 revision */
- return false;
-}
-
-int uart_boot_selected(void)
-{
- /* UART boot is not selected in any SPEAr600 revision */
- return false;
-}
-
-int spi_boot_selected(void)
-{
- /* SPI boot is not selected in any SPEAr600 revision */
- return false;
-}
-
-int i2c_boot_selected(void)
-{
- /* I2C boot is not selected in any SPEAr600 revision */
- return false;
-}
-
-int mmc_boot_selected(void)
-{
- return false;
-}
-
-void plat_late_init(void)
-{
- spear_late_init();
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2011
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-#include <common.h>
-#include <init.h>
-#include <spl.h>
-#include <version.h>
-#include <asm/io.h>
-#include <asm/ptrace.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_defs.h>
-#include <asm/arch/spr_misc.h>
-#include <asm/arch/spr_syscntl.h>
-#include <linux/mtd/st_smi.h>
-
-/* Reserve some space to store the BootROM's stack pointer during SPL operation.
- * The BSS cannot be used for this purpose because it will be zeroed after
- * having stored the pointer, so force the location to the data section.
- */
-u32 bootrom_stash_sp __section(".data");
-
-static void ddr_clock_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 clkenb, ddrpll;
-
- clkenb = readl(&misc_p->periph1_clken);
- clkenb &= ~PERIPH_MPMCMSK;
- clkenb |= PERIPH_MPMC_WE;
-
- /* Intentionally done twice */
- writel(clkenb, &misc_p->periph1_clken);
- writel(clkenb, &misc_p->periph1_clken);
-
- ddrpll = readl(&misc_p->pll_ctr_reg);
- ddrpll &= ~MEM_CLK_SEL_MSK;
-#if (CONFIG_DDR_HCLK)
- ddrpll |= MEM_CLK_HCLK;
-#elif (CONFIG_DDR_2HCLK)
- ddrpll |= MEM_CLK_2HCLK;
-#elif (CONFIG_DDR_PLL2)
- ddrpll |= MEM_CLK_PLL2;
-#else
-#error "please define one of CONFIG_DDR_(HCLK|2HCLK|PLL2)"
-#endif
- writel(ddrpll, &misc_p->pll_ctr_reg);
-
- writel(readl(&misc_p->periph1_clken) | PERIPH_MPMC_EN,
- &misc_p->periph1_clken);
-}
-
-static void mpmc_init_values(void)
-{
- u32 i;
- u32 *mpmc_reg_p = (u32 *)CONFIG_SPEAR_MPMCBASE;
- u32 *mpmc_val_p = &mpmc_conf_vals[0];
-
- for (i = 0; i < CONFIG_SPEAR_MPMCREGS; i++, mpmc_reg_p++, mpmc_val_p++)
- writel(*mpmc_val_p, mpmc_reg_p);
-
- mpmc_reg_p = (u32 *)CONFIG_SPEAR_MPMCBASE;
-
- /*
- * MPMC controller start
- * MPMC waiting for DLLLOCKREG high
- */
- writel(0x01000100, &mpmc_reg_p[7]);
-
- while (!(readl(&mpmc_reg_p[3]) & 0x10000))
- ;
-}
-
-static void mpmc_init(void)
-{
- /* Clock related settings for DDR */
- ddr_clock_init();
-
- /*
- * DDR pad register bits are different for different SoCs
- * Compensation values are also handled separately
- */
- plat_ddr_init();
-
- /* Initialize mpmc register values */
- mpmc_init_values();
-}
-
-static void pll_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
- /* Initialize PLLs */
- writel(FREQ_332, &misc_p->pll1_frq);
- writel(0x1C0A, &misc_p->pll1_cntl);
- writel(0x1C0E, &misc_p->pll1_cntl);
- writel(0x1C06, &misc_p->pll1_cntl);
- writel(0x1C0E, &misc_p->pll1_cntl);
-
- writel(FREQ_332, &misc_p->pll2_frq);
- writel(0x1C0A, &misc_p->pll2_cntl);
- writel(0x1C0E, &misc_p->pll2_cntl);
- writel(0x1C06, &misc_p->pll2_cntl);
- writel(0x1C0E, &misc_p->pll2_cntl);
-
- /* wait for pll locks */
- while (!(readl(&misc_p->pll1_cntl) & 0x1))
- ;
- while (!(readl(&misc_p->pll2_cntl) & 0x1))
- ;
-}
-
-static void mac_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
- writel(readl(&misc_p->periph1_clken) & (~PERIPH_GMAC),
- &misc_p->periph1_clken);
-
- writel(SYNTH23, &misc_p->gmac_synth_clk);
-
- switch (get_socrev()) {
- case SOC_SPEAR600_AA:
- case SOC_SPEAR600_AB:
- case SOC_SPEAR600_BA:
- case SOC_SPEAR600_BB:
- case SOC_SPEAR600_BC:
- case SOC_SPEAR600_BD:
- writel(0x0, &misc_p->gmac_ctr_reg);
- break;
-
- case SOC_SPEAR300:
- case SOC_SPEAR310:
- case SOC_SPEAR320:
- writel(0x4, &misc_p->gmac_ctr_reg);
- break;
- }
-
- writel(readl(&misc_p->periph1_clken) | PERIPH_GMAC,
- &misc_p->periph1_clken);
-
- writel(readl(&misc_p->periph1_rst) | PERIPH_GMAC,
- &misc_p->periph1_rst);
- writel(readl(&misc_p->periph1_rst) & (~PERIPH_GMAC),
- &misc_p->periph1_rst);
-}
-
-static void sys_init(void)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- struct syscntl_regs *syscntl_p =
- (struct syscntl_regs *)CONFIG_SPEAR_SYSCNTLBASE;
-
- /* Set system state to SLOW */
- writel(SLOW, &syscntl_p->scctrl);
- writel(PLL_TIM << 3, &syscntl_p->scpllctrl);
-
- /* Initialize PLLs */
- pll_init();
-
- /*
- * Ethernet configuration
- * To be done only if the tftp boot is not selected already
- * Boot code ensures the correct configuration in tftp booting
- */
- if (!tftp_boot_selected())
- mac_init();
-
- writel(RTC_DISABLE | PLLTIMEEN, &misc_p->periph_clk_cfg);
- writel(0x555, &misc_p->amba_clk_cfg);
-
- writel(NORMAL, &syscntl_p->scctrl);
-
- /* Wait for system to switch to normal mode */
- while (((readl(&syscntl_p->scctrl) >> MODE_SHIFT) & MODE_MASK)
- != NORMAL)
- ;
-}
-
-/*
- * get_socrev
- *
- * Get SoC Revision.
- * @return SOC_SPEARXXX
- */
-int get_socrev(void)
-{
-#if defined(CONFIG_SPEAR600)
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 soc_id = readl(&misc_p->soc_core_id);
- u32 pri_socid = (soc_id >> SOC_PRI_SHFT) & 0xFF;
- u32 sec_socid = (soc_id >> SOC_SEC_SHFT) & 0xFF;
-
- if ((pri_socid == 'B') && (sec_socid == 'B'))
- return SOC_SPEAR600_BB;
- else if ((pri_socid == 'B') && (sec_socid == 'C'))
- return SOC_SPEAR600_BC;
- else if ((pri_socid == 'B') && (sec_socid == 'D'))
- return SOC_SPEAR600_BD;
- else if (soc_id == 0)
- return SOC_SPEAR600_BA;
- else
- return SOC_SPEAR_NA;
-#endif
-}
-
-/*
- * SNOR (Serial NOR flash) related functions
- */
-static void snor_init(void)
-{
- struct smi_regs *const smicntl =
- (struct smi_regs * const)CONFIG_SYS_SMI_BASE;
-
- /* Setting the fast mode values. SMI working at 166/4 = 41.5 MHz */
- writel(HOLD1 | FAST_MODE | BANK_EN | DSEL_TIME | PRESCAL4,
- &smicntl->smi_cr1);
-}
-
-u32 spl_boot_device(void)
-{
- u32 mode = 0;
-
- if (usb_boot_selected()) {
- mode = BOOT_DEVICE_BOOTROM;
- } else if (snor_boot_selected()) {
- /* SNOR-SMI initialization */
- snor_init();
-
- mode = BOOT_DEVICE_NOR;
- }
-
- return mode;
-}
-
-void board_boot_order(u32 *spl_boot_list)
-{
- spl_boot_list[0] = spl_boot_device();
-
- /*
- * If the main boot device (eg. NOR) is empty, try to jump back into the
- * BootROM for USB boot process.
- */
- if (USB_BOOT_SUPPORTED)
- spl_boot_list[1] = BOOT_DEVICE_BOOTROM;
-}
-
-void board_init_f(ulong dummy)
-{
- struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
- /* Initialize PLLs */
- sys_init();
-
- preloader_console_init();
- arch_cpu_init();
-
- /* Enable IPs (release reset) */
- writel(PERIPH_RST_ALL, &misc_p->periph1_rst);
-
- /* Initialize MPMC */
- puts("Configure DDR\n");
- mpmc_init();
- spear_late_init();
-}
-
-/*
- * In a few cases (Ethernet, UART or USB boot, we might want to go back into the
- * BootROM code right after having initialized a few components like the DRAM).
- * The following function is called from SPL common code (board_init_r).
- */
-int board_return_to_bootrom(struct spl_image_info *spl_image,
- struct spl_boot_device *bootdev)
-{
- /*
- * Retrieve the BootROM's stack pointer and jump back to the start of
- * the SPL, where we can easily branch back into the BootROM. Don't do
- * it right here because SPL might be compiled in Thumb mode while the
- * BootROM expects ARM mode.
- */
- asm volatile ("ldr r0, =bootrom_stash_sp;"
- "ldr r0, [r0];"
- "mov sp, r0;"
-#if defined(CONFIG_SPL_SYS_THUMB_BUILD)
- "blx back_to_bootrom;"
-#else
- "bl back_to_bootrom;"
-#endif
- );
-
- return 0;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2009
- * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com
- */
-
-#include <common.h>
-
-#if (CONFIG_DDR_PLL2)
-
-const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = {
- 0x00000001,
- 0x00000000,
- 0x01000000,
- 0x00000101,
- 0x00000001,
- 0x01000000,
- 0x00010001,
- 0x00000100,
- 0x00010001,
- 0x00000003,
- 0x01000201,
- 0x06000202,
- 0x06060106,
- 0x03050502,
- 0x03040404,
- 0x02020503,
- 0x02010106,
- 0x03000404,
- 0x02030202,
- 0x03000204,
- 0x0707073f,
- 0x07070707,
- 0x06060607,
- 0x06060606,
- 0x05050506,
- 0x05050505,
- 0x04040405,
- 0x04040404,
- 0x03030304,
- 0x03030303,
- 0x02020203,
- 0x02020202,
- 0x01010102,
- 0x01010101,
- 0x08080a01,
- 0x0000023f,
- 0x00040800,
- 0x00000000,
- 0x00000f02,
- 0x00001b1b,
- 0x7f000000,
- 0x005f0000,
- 0x1c040b6a,
- 0x00640064,
- 0x00640064,
- 0x00640064,
- 0x00000064,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x000007ff,
- 0x00000000,
- 0x47ec00c8,
- 0x00c8001f,
- 0x00000000,
- 0x0000cd98,
- 0x00000000,
- 0x03030100,
- 0x03030303,
- 0x03030303,
- 0x03030303,
- 0x00270000,
- 0x00250027,
- 0x00300000,
- 0x008900b7,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000
-};
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2009
- * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com
- */
-
-#include <common.h>
-
-#if (CONFIG_DDR_PLL2 || CONFIG_DDR_2HCLK)
-
-const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = {
-#if (CONFIG_DDR_PLL2)
- 0x00000001,
- 0x00000000,
-#elif (CONFIG_DDR_2HCLK)
- 0x02020201,
- 0x02020202,
-#endif
- 0x01000000,
- 0x00000101,
- 0x00000101,
- 0x01000000,
- 0x00010001,
- 0x00000100,
- 0x01010001,
- 0x00000201,
- 0x01000101,
- 0x06000002,
- 0x06060106,
- 0x03050502,
- 0x03040404,
- 0x02020503,
- 0x02010106,
- 0x03000405,
- 0x03040202,
- 0x04000305,
- 0x0707073f,
- 0x07070707,
- 0x06060607,
- 0x06060606,
- 0x05050506,
- 0x05050505,
- 0x04040405,
- 0x04040404,
- 0x03030304,
- 0x03030303,
- 0x02020203,
- 0x02020202,
- 0x01010102,
- 0x01010101,
- 0x0a0a0a01,
- 0x0000023f,
- 0x00050a00,
- 0x11000000,
- 0x00001302,
- 0x00000A0A,
- 0x72000000,
- 0x00550000,
- 0x2b050e86,
- 0x00640064,
- 0x00640064,
- 0x00640064,
- 0x00000064,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00000a24,
- 0x43C20000,
- 0x5b1c00c8,
- 0x00c8002e,
- 0x00000000,
- 0x0001046b,
- 0x00000000,
- 0x03030100,
- 0x03030303,
- 0x03030303,
- 0x03030303,
- 0x00210000,
- 0x00010021,
- 0x00200000,
- 0x006c0090,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000
-};
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2009
- * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com
- */
-
-#include <common.h>
-
-#if (CONFIG_DDR_HCLK)
-
-const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = {
- 0x03030301,
- 0x03030303,
- 0x01000000,
- 0x00000101,
- 0x00000001,
- 0x01000000,
- 0x00010001,
- 0x00000100,
- 0x00010001,
- 0x00000003,
- 0x01000201,
- 0x06000202,
- 0x06060106,
- 0x03050502,
- 0x03040404,
- 0x02020503,
- 0x02010106,
- 0x03000404,
- 0x02020202,
- 0x03000203,
- 0x0707073f,
- 0x07070707,
- 0x06060607,
- 0x06060606,
- 0x05050506,
- 0x05050505,
- 0x04040405,
- 0x04040404,
- 0x03030304,
- 0x03030303,
- 0x02020203,
- 0x02020202,
- 0x01010102,
- 0x01010101,
- 0x08080a01,
- 0x0000023f,
- 0x00030600,
- 0x00000000,
- 0x00000a02,
- 0x00001c1c,
- 0x7f000000,
- 0x005f0000,
- 0x12030743,
- 0x00640064,
- 0x00640064,
- 0x00640064,
- 0x00000064,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x0000050e,
- 0x00000000,
- 0x2d8900c8,
- 0x00c80014,
- 0x00000000,
- 0x00008236,
- 0x00000000,
- 0x03030100,
- 0x03030303,
- 0x03030303,
- 0x03030303,
- 0x00400000,
- 0x003a0040,
- 0x00680000,
- 0x00d80120,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000
-};
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000-2009
- * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com
- */
-
-#include <common.h>
-
-#if (CONFIG_DDR_PLL2 || CONFIG_DDR_2HCLK)
-
-const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = {
-#if (CONFIG_DDR_PLL2)
- 0x00000001,
- 0x00000000,
-#elif (CONFIG_DDR_2HCLK)
- 0x02020201,
- 0x02020202,
-#endif
- 0x01000000,
- 0x00000101,
- 0x00000101,
- 0x01000000,
- 0x00010001,
- 0x00000100,
- 0x01010001,
- 0x00000201,
- 0x01000101,
- 0x06000002,
- 0x06060106,
- 0x03050502,
- 0x03040404,
- 0x02020503,
-#ifdef CONFIG_X600
- 0x02030206,
-#else
- 0x02010106,
-#endif
- 0x03000405,
- 0x03040202,
- 0x04000305,
- 0x0707073f,
- 0x07070707,
- 0x06060607,
- 0x06060606,
- 0x05050506,
- 0x05050505,
- 0x04040405,
- 0x04040404,
- 0x03030304,
- 0x03030303,
- 0x02020203,
- 0x02020202,
- 0x01010102,
- 0x01010101,
- 0x0a0a0a01,
- 0x0000023f,
- 0x00050a00,
- 0x11000000,
- 0x00001302,
- 0x00000A0A,
-#ifdef CONFIG_X600
- 0x7f000000,
- 0x005c0000,
-#else
- 0x72000000,
- 0x00550000,
-#endif
- 0x2b050e86,
- 0x00640064,
- 0x00640064,
- 0x00640064,
- 0x00000064,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00200020,
- 0x00000a24,
- 0x43C20000,
- 0x5b1c00c8,
- 0x00c8002e,
- 0x00000000,
- 0x0001046b,
- 0x00000000,
- 0x03030100,
- 0x03030303,
- 0x03030303,
- 0x03030303,
- 0x00210000,
- 0x00010021,
- 0x00200000,
- 0x006c0090,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x003fffff,
- 0x003fffff,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000,
- 0x00000000
-};
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2006
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <config.h>
-
-/*
- * platform specific initializations are already done in Xloader
- * Initializations already done include
- * DDR, PLLs, IP's clock enable and reset release etc
- */
-.globl lowlevel_init
-lowlevel_init:
- mov pc, lr
-
-/* void setfreq(unsigned int device, unsigned int frequency) */
-.global setfreq
-setfreq:
- stmfd sp!,{r14}
- stmfd sp!,{r0-r12}
-
- mov r8,sp
- ldr sp,SRAM_STACK_V
-
- /* Saving the function arguements for later use */
- mov r4,r0
- mov r5,r1
-
- /* Putting DDR into self refresh */
- ldr r0,DDR_07_V
- ldr r1,[r0]
- ldr r2,DDR_ACTIVE_V
- bic r1, r1, r2
- str r1,[r0]
- ldr r0,DDR_57_V
- ldr r1,[r0]
- ldr r2,CYCLES_MASK_V
- bic r1, r1, r2
- ldr r2,REFRESH_CYCLES_V
- orr r1, r1, r2, lsl #16
- str r1,[r0]
- ldr r0,DDR_07_V
- ldr r1,[r0]
- ldr r2,SREFRESH_MASK_V
- orr r1, r1, r2
- str r1,[r0]
-
- /* flush pipeline */
- b flush
- .align 5
-flush:
- /* Delay to ensure self refresh mode */
- ldr r0,SREFRESH_DELAY_V
-delay:
- sub r0,r0,#1
- cmp r0,#0
- bne delay
-
- /* Putting system in slow mode */
- ldr r0,SCCTRL_V
- mov r1,#2
- str r1,[r0]
-
- /* Changing PLL(1/2) frequency */
- mov r0,r4
- mov r1,r5
-
- cmp r4,#0
- beq pll1_freq
-
- /* Change PLL2 (DDR frequency) */
- ldr r6,PLL2_FREQ_V
- ldr r7,PLL2_CNTL_V
- b pll2_freq
-
-pll1_freq:
- /* Change PLL1 (CPU frequency) */
- ldr r6,PLL1_FREQ_V
- ldr r7,PLL1_CNTL_V
-
-pll2_freq:
- mov r0,r6
- ldr r1,[r0]
- ldr r2,PLLFREQ_MASK_V
- bic r1,r1,r2
- mov r2,r5,lsr#1
- orr r1,r1,r2,lsl#24
- str r1,[r0]
-
- mov r0,r7
- ldr r1,P1C0A_V
- str r1,[r0]
- ldr r1,P1C0E_V
- str r1,[r0]
- ldr r1,P1C06_V
- str r1,[r0]
- ldr r1,P1C0E_V
- str r1,[r0]
-
-lock:
- ldr r1,[r0]
- and r1,r1,#1
- cmp r1,#0
- beq lock
-
- /* Putting system back to normal mode */
- ldr r0,SCCTRL_V
- mov r1,#4
- str r1,[r0]
-
- /* Putting DDR back to normal */
- ldr r0,DDR_07_V
- ldr r1,[R0]
- ldr r2,SREFRESH_MASK_V
- bic r1, r1, r2
- str r1,[r0]
- ldr r2,DDR_ACTIVE_V
- orr r1, r1, r2
- str r1,[r0]
-
- /* Delay to ensure self refresh mode */
- ldr r0,SREFRESH_DELAY_V
-1:
- sub r0,r0,#1
- cmp r0,#0
- bne 1b
-
- mov sp,r8
- /* Resuming back to code */
- ldmia sp!,{r0-r12}
- ldmia sp!,{pc}
-
-SCCTRL_V:
- .word 0xfca00000
-PLL1_FREQ_V:
- .word 0xfca8000C
-PLL1_CNTL_V:
- .word 0xfca80008
-PLL2_FREQ_V:
- .word 0xfca80018
-PLL2_CNTL_V:
- .word 0xfca80014
-PLLFREQ_MASK_V:
- .word 0xff000000
-P1C0A_V:
- .word 0x1C0A
-P1C0E_V:
- .word 0x1C0E
-P1C06_V:
- .word 0x1C06
-
-SREFRESH_DELAY_V:
- .word 0x9999
-SRAM_STACK_V:
- .word 0xD2800600
-DDR_07_V:
- .word 0xfc60001c
-DDR_ACTIVE_V:
- .word 0x01000000
-DDR_57_V:
- .word 0xfc6000e4
-CYCLES_MASK_V:
- .word 0xffff0000
-REFRESH_CYCLES_V:
- .word 0xf0f0
-SREFRESH_MASK_V:
- .word 0x00010000
-
-.global setfreq_sz
-setfreq_sz:
- .word setfreq_sz - setfreq
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <command.h>
-#include <cpu_func.h>
-#include <env.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <asm/global_data.h>
-#include <linux/mtd/st_smi.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_emi.h>
-#include <asm/arch/spr_defs.h>
-
-#define CPU 0
-#define DDR 1
-#define SRAM_REL 0xD2801000
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_CMD_NET)
-static int i2c_read_mac(uchar *buffer);
-#endif
-
-int dram_init(void)
-{
- /* Store complete RAM size and return */
- gd->ram_size = get_ram_size(PHYS_SDRAM_1, PHYS_SDRAM_1_MAXSIZE);
-
- return 0;
-}
-
-int dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = gd->ram_size;
-
- return 0;
-}
-
-int board_early_init_f()
-{
-#if defined(CONFIG_ST_SMI)
- smi_init();
-#endif
- return 0;
-}
-int misc_init_r(void)
-{
-#if defined(CONFIG_CMD_NET)
- uchar mac_id[6];
-
- if (!eth_env_get_enetaddr("ethaddr", mac_id) && !i2c_read_mac(mac_id))
- eth_env_set_enetaddr("ethaddr", mac_id);
-#endif
- env_set("verify", "n");
-
-#if defined(CONFIG_SPEAR_USBTTY)
- env_set("stdin", "usbtty");
- env_set("stdout", "usbtty");
- env_set("stderr", "usbtty");
-
-#ifndef CONFIG_SYS_NO_DCACHE
- dcache_enable();
-#endif
-#endif
- return 0;
-}
-
-#ifdef CONFIG_SPEAR_EMI
-struct cust_emi_para {
- unsigned int tap;
- unsigned int tsdp;
- unsigned int tdpw;
- unsigned int tdpr;
- unsigned int tdcs;
-};
-
-/* EMI timing setting of m28w640hc of linux kernel */
-const struct cust_emi_para emi_timing_m28w640hc = {
- .tap = 0x10,
- .tsdp = 0x05,
- .tdpw = 0x0a,
- .tdpr = 0x0a,
- .tdcs = 0x05,
-};
-
-/* EMI timing setting of bootrom */
-const struct cust_emi_para emi_timing_bootrom = {
- .tap = 0xf,
- .tsdp = 0x0,
- .tdpw = 0xff,
- .tdpr = 0x111,
- .tdcs = 0x02,
-};
-
-void spear_emi_init(void)
-{
- const struct cust_emi_para *p = &emi_timing_m28w640hc;
- struct emi_regs *emi_regs_p = (struct emi_regs *)CONFIG_SPEAR_EMIBASE;
- unsigned int cs;
- unsigned int val, tmp;
-
- val = readl(CONFIG_SPEAR_RASBASE);
-
- if (val & EMI_ACKMSK)
- tmp = 0x3f;
- else
- tmp = 0x0;
-
- writel(tmp, &emi_regs_p->ack);
-
- for (cs = 0; cs < CONFIG_SYS_MAX_FLASH_BANKS; cs++) {
- writel(p->tap, &emi_regs_p->bank_regs[cs].tap);
- writel(p->tsdp, &emi_regs_p->bank_regs[cs].tsdp);
- writel(p->tdpw, &emi_regs_p->bank_regs[cs].tdpw);
- writel(p->tdpr, &emi_regs_p->bank_regs[cs].tdpr);
- writel(p->tdcs, &emi_regs_p->bank_regs[cs].tdcs);
- writel(EMI_CNTL_ENBBYTERW | ((val & 0x18) >> 3),
- &emi_regs_p->bank_regs[cs].control);
- }
-}
-#endif
-
-int spear_board_init(ulong mach_type)
-{
- gd->bd->bi_arch_number = mach_type;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = CONFIG_BOOT_PARAMS_ADDR;
-
-#ifdef CONFIG_SPEAR_EMI
- spear_emi_init();
-#endif
- return 0;
-}
-
-#if defined(CONFIG_CMD_NET)
-static int i2c_read_mac(uchar *buffer)
-{
- u8 buf[2];
-
- i2c_read(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN);
-
- /* Check if mac in i2c memory is valid */
- if ((buf[0] == MAGIC_BYTE0) && (buf[1] == MAGIC_BYTE1)) {
- /* Valid mac address is saved in i2c eeprom */
- i2c_read(CONFIG_I2C_CHIPADDRESS, MAC_OFF, 1, buffer, MAC_LEN);
- return 0;
- }
-
- return -1;
-}
-
-static int write_mac(uchar *mac)
-{
- u8 buf[2];
-
- buf[0] = (u8)MAGIC_BYTE0;
- buf[1] = (u8)MAGIC_BYTE1;
- i2c_write(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN);
-
- buf[0] = (u8)~MAGIC_BYTE0;
- buf[1] = (u8)~MAGIC_BYTE1;
-
- i2c_read(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN);
-
- /* check if valid MAC address is saved in I2C EEPROM or not? */
- if ((buf[0] == MAGIC_BYTE0) && (buf[1] == MAGIC_BYTE1)) {
- i2c_write(CONFIG_I2C_CHIPADDRESS, MAC_OFF, 1, mac, MAC_LEN);
- puts("I2C EEPROM written with mac address \n");
- return 0;
- }
-
- puts("I2C EEPROM writing failed\n");
- return -1;
-}
-#endif
-
-int do_chip_config(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- void (*sram_setfreq) (unsigned int, unsigned int);
- unsigned int frequency;
-#if defined(CONFIG_CMD_NET)
- unsigned char mac[6];
-#endif
-
- if ((argc > 3) || (argc < 2))
- return cmd_usage(cmdtp);
-
- if ((!strcmp(argv[1], "cpufreq")) || (!strcmp(argv[1], "ddrfreq"))) {
-
- frequency = simple_strtoul(argv[2], NULL, 0);
-
- if (frequency > 333) {
- printf("Frequency is limited to 333MHz\n");
- return 1;
- }
-
- sram_setfreq = memcpy((void *)SRAM_REL, setfreq, setfreq_sz);
-
- if (!strcmp(argv[1], "cpufreq")) {
- sram_setfreq(CPU, frequency);
- printf("CPU frequency changed to %u\n", frequency);
- } else {
- sram_setfreq(DDR, frequency);
- printf("DDR frequency changed to %u\n", frequency);
- }
-
- return 0;
-
-#if defined(CONFIG_CMD_NET)
- } else if (!strcmp(argv[1], "ethaddr")) {
-
- u32 reg;
- char *e, *s = argv[2];
- for (reg = 0; reg < 6; ++reg) {
- mac[reg] = s ? simple_strtoul(s, &e, 16) : 0;
- if (s)
- s = (*e) ? e + 1 : e;
- }
- write_mac(mac);
-
- return 0;
-#endif
- } else if (!strcmp(argv[1], "print")) {
-#if defined(CONFIG_CMD_NET)
- if (!i2c_read_mac(mac)) {
- printf("Ethaddr (from i2c mem) = %pM\n", mac);
- } else {
- printf("Ethaddr (from i2c mem) = Not set\n");
- }
-#endif
- return 0;
- }
-
- return cmd_usage(cmdtp);
-}
-
-U_BOOT_CMD(chip_config, 3, 1, do_chip_config,
- "configure chip",
- "chip_config cpufreq/ddrfreq frequency\n"
-#if defined(CONFIG_CMD_NET)
- "chip_config ethaddr XX:XX:XX:XX:XX:XX\n"
-#endif
- "chip_config print");
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * armboot - Startup Code for ARM926EJS CPU-core
- *
- * Copyright (c) 2003 Texas Instruments
- *
- * ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------
- *
- * Copyright (c) 2001 Marius Gröger <mag@sysgo.de>
- * Copyright (c) 2002 Alex Züpke <azu@sysgo.de>
- * Copyright (c) 2002 Gary Jennejohn <garyj@denx.de>
- * Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
- * Copyright (c) 2003 Kshitij <kshitij@ti.com>
- */
-
-
-#include <config.h>
-
-/*
- *************************************************************************
- *
- * Startup Code (reset vector)
- *
- * The BootROM already initialized its own stack in the [0-0xb00] reserved
- * range of the SRAM. The SPL (in _main) will update the stack pointer to
- * its own SRAM area (right before the gd section).
- *
- *************************************************************************
- */
-
- .globl reset
- .globl back_to_bootrom
-
-reset:
- /*
- * SPL has to return back to BootROM in a few cases (eg. Ethernet boot,
- * UART boot, USB boot): save registers in BootROM's stack and then the
- * BootROM's stack pointer in the SPL's data section.
- */
- push {r0-r12,lr}
- ldr r0, =bootrom_stash_sp
- str sp, [r0]
-
- /*
- * Flush v4 I/D caches
- */
- mov r0, #0
- mcr p15, 0, r0, c7, c7, 0 /* Flush v3/v4 cache */
- mcr p15, 0, r0, c8, c7, 0 /* Flush v4 TLB */
-
- /*
- * Enable instruction cache
- */
- mrc p15, 0, r0, c1, c0, 0
- orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
- mcr p15, 0, r0, c1, c0, 0
-
- /*
- * Go setup Memory and board specific bits prior to relocation.
- * This call is not supposed to return.
- */
- b _main /* _main will call board_init_f */
-
-back_to_bootrom:
- pop {r0-r12,pc}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <init.h>
-#include <time.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_gpt.h>
-#include <asm/arch/spr_misc.h>
-#include <asm/ptrace.h>
-#include <linux/delay.h>
-
-#define GPT_RESOLUTION (CONFIG_SPEAR_HZ_CLOCK / CONFIG_SPEAR_HZ)
-#define READ_TIMER() (readl(&gpt_regs_p->count) & GPT_FREE_RUNNING)
-
-static struct gpt_regs *const gpt_regs_p =
- (struct gpt_regs *)CONFIG_SPEAR_TIMERBASE;
-
-static struct misc_regs *const misc_regs_p =
- (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static ulong get_timer_masked(void);
-
-#define timestamp gd->arch.tbl
-#define lastdec gd->arch.lastinc
-
-int timer_init(void)
-{
- u32 synth;
-
- /* Prescaler setting */
-#if defined(CONFIG_SPEAR600)
- writel(MISC_PRSC_CFG, &misc_regs_p->prsc1_clk_cfg);
- synth = MISC_GPT3SYNTH;
-#else
-# error Incorrect config. Can only be SPEAR{600|300|310|320}
-#endif
-
- writel(readl(&misc_regs_p->periph_clk_cfg) | synth,
- &misc_regs_p->periph_clk_cfg);
-
- /* disable timers */
- writel(GPT_PRESCALER_1 | GPT_MODE_AUTO_RELOAD, &gpt_regs_p->control);
-
- /* load value for free running */
- writel(GPT_FREE_RUNNING, &gpt_regs_p->compare);
-
- /* auto reload, start timer */
- writel(readl(&gpt_regs_p->control) | GPT_ENABLE, &gpt_regs_p->control);
-
- /* Reset the timer */
- lastdec = READ_TIMER();
- timestamp = 0;
-
- return 0;
-}
-
-/*
- * timer without interrupts
- */
-ulong get_timer(ulong base)
-{
- return (get_timer_masked() / GPT_RESOLUTION) - base;
-}
-
-void __udelay(unsigned long usec)
-{
- ulong tmo;
- ulong start = get_timer_masked();
- ulong tenudelcnt = CONFIG_SPEAR_HZ_CLOCK / (1000 * 100);
- ulong rndoff;
-
- rndoff = (usec % 10) ? 1 : 0;
-
- /* tenudelcnt timer tick gives 10 microsecconds delay */
- tmo = ((usec / 10) + rndoff) * tenudelcnt;
-
- while ((ulong) (get_timer_masked() - start) < tmo)
- ;
-}
-
-static ulong get_timer_masked(void)
-{
- ulong now = READ_TIMER();
-
- if (now >= lastdec) {
- /* normal mode */
- timestamp += now - lastdec;
- } else {
- /* we have an overflow ... */
- timestamp += now + GPT_FREE_RUNNING - lastdec;
- }
- lastdec = now;
-
- return timestamp;
-}
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
- return get_timer(0);
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk(void)
-{
- return CONFIG_SPEAR_HZ;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2015 Stefan Roese <sr@denx.de>
- *
- * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
- * on behalf of DENX Software Engineering GmbH
- *
- * January 2004 - Changed to support H4 device
- * Copyright (c) 2004-2008 Texas Instruments
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- */
-
-MEMORY { .sram : ORIGIN = IMAGE_TEXT_BASE,\
- LENGTH = IMAGE_MAX_SIZE }
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- .text :
- {
- __start = .;
- *(.vectors)
- CPUDIR/spear/start.o (.text*)
- *(.text*)
- } > .sram
-
- . = ALIGN(4);
- .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
-
- . = ALIGN(4);
- .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- } > .sram
-
- . = ALIGN(4);
- __image_copy_end = .;
- _end = .;
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start = .;
- *(.bss*)
- . = ALIGN(4);
- __bss_end = .;
- } > .sram
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2010, STMicroelectronics - All Rights Reserved
- * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics.
- */
-
-static inline unsigned long get_macb_pclk_rate(unsigned int dev_id)
-{
- return 83000000;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-
-#ifndef __ASM_ARCH_SPEAR_GPIO_H
-#define __ASM_ARCH_SPEAR_GPIO_H
-
-enum gpio_direction {
- GPIO_DIRECTION_IN,
- GPIO_DIRECTION_OUT,
-};
-
-struct gpio_regs {
- u32 gpiodata[0x100]; /* 0x000 ... 0x3fc */
- u32 gpiodir; /* 0x400 */
-};
-
-#define SPEAR_GPIO_COUNT 8
-#define DATA_REG_ADDR(gpio) (1 << (gpio + 2))
-
-#endif /* __ASM_ARCH_SPEAR_GPIO_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2009, STMicroelectronics - All Rights Reserved
- * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics.
- */
-
-#ifndef _ASM_ARCH_HARDWARE_H
-#define _ASM_ARCH_HARDWARE_H
-
-#define CONFIG_SYS_USBD_BASE 0xE1100000
-#define CONFIG_SYS_PLUG_BASE 0xE1200000
-#define CONFIG_SYS_FIFO_BASE 0xE1000800
-#define CONFIG_SYS_UHC0_EHCI_BASE 0xE1800000
-#define CONFIG_SYS_UHC1_EHCI_BASE 0xE2000000
-#define CONFIG_SYS_SMI_BASE 0xFC000000
-#define CONFIG_SPEAR_SYSCNTLBASE 0xFCA00000
-#define CONFIG_SPEAR_TIMERBASE 0xFC800000
-#define CONFIG_SPEAR_MISCBASE 0xFCA80000
-#define CONFIG_SPEAR_ETHBASE 0xE0800000
-#define CONFIG_SPEAR_MPMCBASE 0xFC600000
-#define CONFIG_SSP1_BASE 0xD0100000
-#define CONFIG_SSP2_BASE 0xD0180000
-#define CONFIG_SSP3_BASE 0xD8180000
-#define CONFIG_GPIO_BASE 0xD8100000
-
-#define CONFIG_SYS_NAND_CLE (1 << 16)
-#define CONFIG_SYS_NAND_ALE (1 << 17)
-
-#if defined(CONFIG_SPEAR600)
-#define CONFIG_SYS_FSMC_BASE 0xD1800000
-#define CONFIG_FSMC_NAND_BASE 0xD2000000
-
-#define CONFIG_SPEAR_BOOTSTRAPCFG 0xFCA80000
-#define CONFIG_SPEAR_BOOTSTRAPSHFT 16
-#define CONFIG_SPEAR_BOOTSTRAPMASK 0xB
-#define CONFIG_SPEAR_ONLYSNORBOOT 0xA
-#define CONFIG_SPEAR_NORNANDBOOT 0xB
-#define CONFIG_SPEAR_NORNAND8BOOT 0x8
-#define CONFIG_SPEAR_NORNAND16BOOT 0x9
-#define CONFIG_SPEAR_USBBOOT 0x8
-
-#define CONFIG_SPEAR_MPMCREGS 100
-
-#endif
-#endif /* _ASM_ARCH_HARDWARE_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#ifndef __SPR_DEFS_H__
-#define __SPR_DEFS_H__
-
-extern int spear_board_init(ulong);
-extern void setfreq(unsigned int, unsigned int);
-extern unsigned int setfreq_sz;
-
-void plat_ddr_init(void);
-void spear_late_init(void);
-
-int snor_boot_selected(void);
-int nand_boot_selected(void);
-int pnor_boot_selected(void);
-int usb_boot_selected(void);
-int uart_boot_selected(void);
-int tftp_boot_selected(void);
-int i2c_boot_selected(void);
-int spi_boot_selected(void);
-int mmc_boot_selected(void);
-
-extern u32 mpmc_conf_vals[];
-
-struct chip_data {
- int cpufreq;
- int dramfreq;
- int dramtype;
- uchar version[32];
-};
-
-/* HW mac id in i2c memory definitions */
-#define MAGIC_OFF 0x0
-#define MAGIC_LEN 0x2
-#define MAGIC_BYTE0 0x55
-#define MAGIC_BYTE1 0xAA
-#define MAC_OFF 0x2
-#define MAC_LEN 0x6
-
-#define PNOR_WIDTH_8 0
-#define PNOR_WIDTH_16 1
-#define PNOR_WIDTH_32 2
-#define PNOR_WIDTH_NUM 3
-#define PNOR_WIDTH_SEARCH 0xff
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Ryan CHEN, ST Micoelectronics, ryan.chen@st.com
- */
-
-#ifndef __SPEAR_EMI_H__
-#define __SPEAR_EMI_H__
-
-#ifdef CONFIG_SPEAR_EMI
-
-struct emi_bank_regs {
- u32 tap;
- u32 tsdp;
- u32 tdpw;
- u32 tdpr;
- u32 tdcs;
- u32 control;
-};
-
-struct emi_regs {
- struct emi_bank_regs bank_regs[CONFIG_SYS_MAX_FLASH_BANKS];
- u32 tout;
- u32 ack;
- u32 irq;
-};
-
-#define EMI_ACKMSK 0x40
-
-/* control register definitions */
-#define EMI_CNTL_ENBBYTEW (1 << 2)
-#define EMI_CNTL_ENBBYTER (1 << 3)
-#define EMI_CNTL_ENBBYTERW (EMI_CNTL_ENBBYTER | EMI_CNTL_ENBBYTEW)
-
-#endif
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#ifndef _SPR_GPT_H
-#define _SPR_GPT_H
-
-struct gpt_regs {
- u8 reserved[0x80];
- u32 control;
- u32 status;
- u32 compare;
- u32 count;
- u32 capture_re;
- u32 capture_fe;
-};
-
-/*
- * TIMER_CONTROL register settings
- */
-
-#define GPT_PRESCALER_MASK 0x000F
-#define GPT_PRESCALER_1 0x0000
-#define GPT_PRESCALER_2 0x0001
-#define GPT_PRESCALER_4 0x0002
-#define GPT_PRESCALER_8 0x0003
-#define GPT_PRESCALER_16 0x0004
-#define GPT_PRESCALER_32 0x0005
-#define GPT_PRESCALER_64 0x0006
-#define GPT_PRESCALER_128 0x0007
-#define GPT_PRESCALER_256 0x0008
-
-#define GPT_MODE_SINGLE_SHOT 0x0010
-#define GPT_MODE_AUTO_RELOAD 0x0000
-
-#define GPT_ENABLE 0x0020
-
-#define GPT_CAPT_MODE_MASK 0x00C0
-#define GPT_CAPT_MODE_NONE 0x0000
-#define GPT_CAPT_MODE_RE 0x0040
-#define GPT_CAPT_MODE_FE 0x0080
-#define GPT_CAPT_MODE_BOTH 0x00C0
-
-#define GPT_INT_MATCH 0x0100
-#define GPT_INT_FE 0x0200
-#define GPT_INT_RE 0x0400
-
-/*
- * TIMER_STATUS register settings
- */
-
-#define GPT_STS_MATCH 0x0001
-#define GPT_STS_FE 0x0002
-#define GPT_STS_RE 0x0004
-
-/*
- * TIMER_COMPARE register settings
- */
-
-#define GPT_FREE_RUNNING 0xFFFF
-
-/* Timer, HZ specific defines */
-#define CONFIG_SPEAR_HZ 1000
-#define CONFIG_SPEAR_HZ_CLOCK 8300000
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#ifndef _SPR_MISC_H
-#define _SPR_MISC_H
-
-struct misc_regs {
- u32 auto_cfg_reg; /* 0x0 */
- u32 armdbg_ctr_reg; /* 0x4 */
- u32 pll1_cntl; /* 0x8 */
- u32 pll1_frq; /* 0xc */
- u32 pll1_mod; /* 0x10 */
- u32 pll2_cntl; /* 0x14 */
- u32 pll2_frq; /* 0x18 */
- u32 pll2_mod; /* 0x1C */
- u32 pll_ctr_reg; /* 0x20 */
- u32 amba_clk_cfg; /* 0x24 */
- u32 periph_clk_cfg; /* 0x28 */
- u32 periph1_clken; /* 0x2C */
- u32 soc_core_id; /* 0x30 */
- u32 ras_clken; /* 0x34 */
- u32 periph1_rst; /* 0x38 */
- u32 periph2_rst; /* 0x3C */
- u32 ras_rst; /* 0x40 */
- u32 prsc1_clk_cfg; /* 0x44 */
- u32 prsc2_clk_cfg; /* 0x48 */
- u32 prsc3_clk_cfg; /* 0x4C */
- u32 amem_cfg_ctrl; /* 0x50 */
- u32 expi_clk_cfg; /* 0x54 */
- u32 reserved_1; /* 0x58 */
- u32 clcd_synth_clk; /* 0x5C */
- u32 irda_synth_clk; /* 0x60 */
- u32 uart_synth_clk; /* 0x64 */
- u32 gmac_synth_clk; /* 0x68 */
- u32 ras_synth1_clk; /* 0x6C */
- u32 ras_synth2_clk; /* 0x70 */
- u32 ras_synth3_clk; /* 0x74 */
- u32 ras_synth4_clk; /* 0x78 */
- u32 arb_icm_ml1; /* 0x7C */
- u32 arb_icm_ml2; /* 0x80 */
- u32 arb_icm_ml3; /* 0x84 */
- u32 arb_icm_ml4; /* 0x88 */
- u32 arb_icm_ml5; /* 0x8C */
- u32 arb_icm_ml6; /* 0x90 */
- u32 arb_icm_ml7; /* 0x94 */
- u32 arb_icm_ml8; /* 0x98 */
- u32 arb_icm_ml9; /* 0x9C */
- u32 dma_src_sel; /* 0xA0 */
- u32 uphy_ctr_reg; /* 0xA4 */
- u32 gmac_ctr_reg; /* 0xA8 */
- u32 port_bridge_ctrl; /* 0xAC */
- u32 reserved_2[4]; /* 0xB0--0xBC */
- u32 prc1_ilck_ctrl_reg; /* 0xC0 */
- u32 prc2_ilck_ctrl_reg; /* 0xC4 */
- u32 prc3_ilck_ctrl_reg; /* 0xC8 */
- u32 prc4_ilck_ctrl_reg; /* 0xCC */
- u32 prc1_intr_ctrl_reg; /* 0xD0 */
- u32 prc2_intr_ctrl_reg; /* 0xD4 */
- u32 prc3_intr_ctrl_reg; /* 0xD8 */
- u32 prc4_intr_ctrl_reg; /* 0xDC */
- u32 powerdown_cfg_reg; /* 0xE0 */
- u32 ddr_1v8_compensation; /* 0xE4 */
- u32 ddr_2v5_compensation; /* 0xE8 */
- u32 core_3v3_compensation; /* 0xEC */
- u32 ddr_pad; /* 0xF0 */
- u32 bist1_ctr_reg; /* 0xF4 */
- u32 bist2_ctr_reg; /* 0xF8 */
- u32 bist3_ctr_reg; /* 0xFC */
- u32 bist4_ctr_reg; /* 0x100 */
- u32 bist5_ctr_reg; /* 0x104 */
- u32 bist1_rslt_reg; /* 0x108 */
- u32 bist2_rslt_reg; /* 0x10C */
- u32 bist3_rslt_reg; /* 0x110 */
- u32 bist4_rslt_reg; /* 0x114 */
- u32 bist5_rslt_reg; /* 0x118 */
- u32 syst_error_reg; /* 0x11C */
- u32 reserved_3[0x1FB8]; /* 0x120--0x7FFC */
- u32 ras_gpp1_in; /* 0x8000 */
- u32 ras_gpp2_in; /* 0x8004 */
- u32 ras_gpp1_out; /* 0x8008 */
- u32 ras_gpp2_out; /* 0x800C */
-};
-
-/* SYNTH_CLK value*/
-#define SYNTH23 0x00020003
-
-/* PLLx_FRQ value */
-#if defined(CONFIG_SPEAR600)
-#define FREQ_332 0xA600010F
-#define FREQ_266 0x8500010F
-#endif
-
-/* PLL_CTR_REG */
-#define MEM_CLK_SEL_MSK 0x70000000
-#define MEM_CLK_HCLK 0x00000000
-#define MEM_CLK_2HCLK 0x10000000
-#define MEM_CLK_PLL2 0x30000000
-
-#define EXPI_CLK_CFG_LOW_COMPR 0x2000
-#define EXPI_CLK_CFG_CLK_EN 0x0400
-#define EXPI_CLK_CFG_RST 0x0200
-#define EXPI_CLK_SYNT_EN 0x0010
-#define EXPI_CLK_CFG_SEL_PLL2 0x0004
-#define EXPI_CLK_CFG_INT_CLK_EN 0x0001
-
-#define PLL2_CNTL_6UA 0x1c00
-#define PLL2_CNTL_SAMPLE 0x0008
-#define PLL2_CNTL_ENABLE 0x0004
-#define PLL2_CNTL_RESETN 0x0002
-#define PLL2_CNTL_LOCK 0x0001
-
-/* AUTO_CFG_REG value */
-#define MISC_SOCCFGMSK 0x0000003F
-#define MISC_SOCCFG30 0x0000000C
-#define MISC_SOCCFG31 0x0000000D
-#define MISC_NANDDIS 0x00020000
-
-/* PERIPH_CLK_CFG value */
-#define MISC_GPT3SYNTH 0x00000400
-#define MISC_GPT4SYNTH 0x00000800
-#define CONFIG_SPEAR_UART48M 0
-#define CONFIG_SPEAR_UARTCLKMSK (0x1 << 4)
-
-/* PRSC_CLK_CFG value */
-/*
- * Fout = Fin / (2^(N+1) * (M + 1))
- */
-#define MISC_PRSC_N_1 0x00001000
-#define MISC_PRSC_M_9 0x00000009
-#define MISC_PRSC_N_4 0x00004000
-#define MISC_PRSC_M_399 0x0000018F
-#define MISC_PRSC_N_6 0x00006000
-#define MISC_PRSC_M_2593 0x00000A21
-#define MISC_PRSC_M_124 0x0000007C
-#define MISC_PRSC_CFG (MISC_PRSC_N_1 | MISC_PRSC_M_9)
-
-/* PERIPH1_CLKEN, PERIPH1_RST value */
-#define MISC_USBDENB 0x01000000
-#define MISC_ETHENB 0x00800000
-#define MISC_SMIENB 0x00200000
-#define MISC_GPIO3ENB 0x00040000
-#define MISC_GPT3ENB 0x00010000
-#define MISC_SSP3ENB 0x00004000
-#define MISC_GPIO4ENB 0x00002000
-#define MISC_GPT2ENB 0x00000800
-#define MISC_FSMCENB 0x00000200
-#define MISC_I2CENB 0x00000080
-#define MISC_SSP2ENB 0x00000040
-#define MISC_SSP1ENB 0x00000020
-#define MISC_UART0ENB 0x00000008
-
-/* PERIPH_CLK_CFG */
-#define XTALTIMEEN 0x00000001
-#define PLLTIMEEN 0x00000002
-#define CLCDCLK_SYNTH 0x00000000
-#define CLCDCLK_48MHZ 0x00000004
-#define CLCDCLK_EXT 0x00000008
-#define UARTCLK_MASK (0x1 << 4)
-#define UARTCLK_48MHZ 0x00000000
-#define UARTCLK_SYNTH 0x00000010
-#define IRDACLK_48MHZ 0x00000000
-#define IRDACLK_SYNTH 0x00000020
-#define IRDACLK_EXT 0x00000040
-#define RTC_DISABLE 0x00000080
-#define GPT1CLK_48MHZ 0x00000000
-#define GPT1CLK_SYNTH 0x00000100
-#define GPT2CLK_48MHZ 0x00000000
-#define GPT2CLK_SYNTH 0x00000200
-#define GPT3CLK_48MHZ 0x00000000
-#define GPT3CLK_SYNTH 0x00000400
-#define GPT4CLK_48MHZ 0x00000000
-#define GPT4CLK_SYNTH 0x00000800
-#define GPT5CLK_48MHZ 0x00000000
-#define GPT5CLK_SYNTH 0x00001000
-#define GPT1_FREEZE 0x00002000
-#define GPT2_FREEZE 0x00004000
-#define GPT3_FREEZE 0x00008000
-#define GPT4_FREEZE 0x00010000
-#define GPT5_FREEZE 0x00020000
-
-/* PERIPH1_CLKEN bits */
-#define PERIPH_ARM1_WE 0x00000001
-#define PERIPH_ARM1 0x00000002
-#define PERIPH_ARM2 0x00000004
-#define PERIPH_UART1 0x00000008
-#define PERIPH_UART2 0x00000010
-#define PERIPH_SSP1 0x00000020
-#define PERIPH_SSP2 0x00000040
-#define PERIPH_I2C 0x00000080
-#define PERIPH_JPEG 0x00000100
-#define PERIPH_FSMC 0x00000200
-#define PERIPH_FIRDA 0x00000400
-#define PERIPH_GPT4 0x00000800
-#define PERIPH_GPT5 0x00001000
-#define PERIPH_GPIO4 0x00002000
-#define PERIPH_SSP3 0x00004000
-#define PERIPH_ADC 0x00008000
-#define PERIPH_GPT3 0x00010000
-#define PERIPH_RTC 0x00020000
-#define PERIPH_GPIO3 0x00040000
-#define PERIPH_DMA 0x00080000
-#define PERIPH_ROM 0x00100000
-#define PERIPH_SMI 0x00200000
-#define PERIPH_CLCD 0x00400000
-#define PERIPH_GMAC 0x00800000
-#define PERIPH_USBD 0x01000000
-#define PERIPH_USBH1 0x02000000
-#define PERIPH_USBH2 0x04000000
-#define PERIPH_MPMC 0x08000000
-#define PERIPH_RAMW 0x10000000
-#define PERIPH_MPMC_EN 0x20000000
-#define PERIPH_MPMC_WE 0x40000000
-#define PERIPH_MPMCMSK 0x60000000
-
-#define PERIPH_CLK_ALL 0x0FFFFFF8
-#define PERIPH_RST_ALL 0x00000004
-
-/* DDR_PAD values */
-#define DDR_PAD_CNF_MSK 0x0000ffff
-#define DDR_PAD_SW_CONF 0x00060000
-#define DDR_PAD_SSTL_SEL 0x00000001
-#define DDR_PAD_DRAM_TYPE 0x00008000
-
-/* DDR_COMP values */
-#define DDR_COMP_ACCURATE 0x00000010
-
-/* SoC revision stuff */
-#define SOC_PRI_SHFT 16
-#define SOC_SEC_SHFT 8
-
-/* Revision definitions */
-#define SOC_SPEAR_NA 0
-
-/*
- * The definitons have started from
- * 101 for SPEAr6xx
- * 201 for SPEAr3xx
- * 301 for SPEAr13xx
- */
-#define SOC_SPEAR600_AA 101
-#define SOC_SPEAR600_AB 102
-#define SOC_SPEAR600_BA 103
-#define SOC_SPEAR600_BB 104
-#define SOC_SPEAR600_BC 105
-#define SOC_SPEAR600_BD 106
-
-#define SOC_SPEAR300 201
-#define SOC_SPEAR310 202
-#define SOC_SPEAR320 203
-
-extern int get_socrev(void);
-int fsmc_nand_switch_ecc(uint32_t eccstrength);
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-#ifndef _SPR_SSP_H
-#define _SPR_SSP_H
-
-struct ssp_regs {
- u32 sspcr0;
- u32 sspcr1;
- u32 sspdr;
- u32 sspsr;
- u32 sspcpsr;
- u32 sspimsc;
- u32 sspicr;
- u32 sspdmacr;
-};
-
-#define SSPCR0_FRF_MOT_SPI 0x0000
-#define SSPCR0_DSS_16BITS 0x000f
-
-#define SSPCR1_SSE 0x0002
-
-#define SSPSR_TNF 0x2
-#define SSPSR_TFE 0x1
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Ryan CHEN, ST Micoelectronics, ryan.chen@st.com
- */
-
-#ifndef __SYSCTRL_H
-#define __SYSCTRL_H
-
-struct syscntl_regs {
- u32 scctrl;
- u32 scsysstat;
- u32 scimctrl;
- u32 scimsysstat;
- u32 scxtalctrl;
- u32 scpllctrl;
- u32 scpllfctrl;
- u32 scperctrl0;
- u32 scperctrl1;
- u32 scperen;
- u32 scperdis;
- const u32 scperclken;
- const u32 scperstat;
-};
-
-#define MODE_SHIFT 0x00000003
-
-#define NORMAL 0x00000004
-#define SLOW 0x00000002
-#define DOZE 0x00000001
-#define SLEEP 0x00000000
-
-#define PLL_TIM 0x01FFFFFF
-
-#endif
+++ /dev/null
-if TARGET_SPEAR600
-
-config SYS_BOARD
- default "spear600"
-
-config SYS_VENDOR
- default "spear"
-
-config SYS_SOC
- default "spear"
-
-config SYS_CONFIG_NAME
- default "spear6xx_evb"
-
-endif
+++ /dev/null
-SPEAR600 BOARD
-M: Vipin Kumar <vipin.kumar@st.com>
-S: Maintained
-F: board/spear/spear600/
-F: include/configs/spear6xx_evb.h
-F: configs/spear600_defconfig
-
-SPEAR600_NAND BOARD
-#M: -
-S: Maintained
-F: configs/spear600_nand_defconfig
-F: configs/spear600_usbtty_defconfig
-F: configs/spear600_usbtty_nand_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000-2004
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += spear600.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <net.h>
-#include <netdev.h>
-#include <nand.h>
-#include <asm/io.h>
-#include <linux/mtd/fsmc_nand.h>
-#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_defs.h>
-#include <asm/arch/spr_misc.h>
-
-static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];
-
-int board_init(void)
-{
- return spear_board_init(MACH_TYPE_SPEAR600);
-}
-
-/*
- * board_nand_init - Board specific NAND initialization
- * @nand: mtd private chip structure
- *
- * Called by nand_init_chip to initialize the board specific functions
- */
-
-void board_nand_init()
-{
- struct misc_regs *const misc_regs_p =
- (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- struct nand_chip *nand = &nand_chip[0];
-
-#if defined(CONFIG_NAND_FSMC)
- if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS))
- fsmc_nand_init(nand);
-#endif
- return;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- int ret = 0;
-
-#if defined(CONFIG_ETH_DESIGNWARE)
- u32 interface = PHY_INTERFACE_MODE_MII;
- if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
- ret++;
-#endif
- return ret;
-}
+++ /dev/null
-if TARGET_X600
-
-config SPL_LDSCRIPT
- default "arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds"
-
-config SYS_BOARD
- default "x600"
-
-config SYS_VENDOR
- default "spear"
-
-config SYS_SOC
- default "spear"
-
-config SYS_CONFIG_NAME
- default "x600"
-
-endif
+++ /dev/null
-X600 BOARD
-M: Stefan Roese <sr@denx.de>
-S: Maintained
-F: board/spear/x600/
-F: include/configs/x600.h
-F: configs/x600_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000-2004
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-ifdef CONFIG_SPL_BUILD
-# necessary to create built-in.o
-obj- := __dummy__.o
-else
-obj-y := fpga.o x600.o
-endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-#include <common.h>
-#include <log.h>
-#include <spartan3.h>
-#include <command.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_misc.h>
-#include <asm/arch/spr_ssp.h>
-#include <linux/delay.h>
-
-/*
- * FPGA program pin configuration on X600:
- *
- * Only PROG and DONE are connected to GPIOs. INIT is not connected to the
- * SoC at all. And CLOCK and DATA are connected to the SSP2 port. We use
- * 16bit serial writes via this SSP port to write the data bits into the
- * FPGA.
- */
-#define CONFIG_SYS_FPGA_PROG 2
-#define CONFIG_SYS_FPGA_DONE 3
-
-/*
- * Set the active-low FPGA reset signal.
- */
-static void fpga_reset(int assert)
-{
- /*
- * On x600 we have no means to toggle the FPGA reset signal
- */
- debug("%s:%d: RESET (%d)\n", __func__, __LINE__, assert);
-}
-
-/*
- * Set the FPGA's active-low SelectMap program line to the specified level
- */
-static int fpga_pgm_fn(int assert, int flush, int cookie)
-{
- debug("%s:%d: FPGA PROG (%d)\n", __func__, __LINE__, assert);
-
- gpio_set_value(CONFIG_SYS_FPGA_PROG, assert);
-
- return assert;
-}
-
-/*
- * Test the state of the active-low FPGA INIT line. Return 1 on INIT
- * asserted (low).
- */
-static int fpga_init_fn(int cookie)
-{
- static int state;
-
- debug("%s:%d: init (state=%d)\n", __func__, __LINE__, state);
-
- /*
- * On x600, the FPGA INIT signal is not connected to the SoC.
- * We can't read the INIT status. Let's return the "correct"
- * INIT signal state generated via a local state-machine.
- */
- if (++state == 1) {
- return 1;
- } else {
- state = 0;
- return 0;
- }
-}
-
-/*
- * Test the state of the active-high FPGA DONE pin
- */
-static int fpga_done_fn(int cookie)
-{
- struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE;
-
- /*
- * Wait for Tx-FIFO to become empty before looking for DONE
- */
- while (!(readl(&ssp->sspsr) & SSPSR_TFE))
- ;
-
- if (gpio_get_value(CONFIG_SYS_FPGA_DONE))
- return 1;
- else
- return 0;
-}
-
-/*
- * FPGA pre-configuration function. Just make sure that
- * FPGA reset is asserted to keep the FPGA from starting up after
- * configuration.
- */
-static int fpga_pre_config_fn(int cookie)
-{
- debug("%s:%d: FPGA pre-configuration\n", __func__, __LINE__);
- fpga_reset(true);
-
- return 0;
-}
-
-/*
- * FPGA post configuration function. Blip the FPGA reset line and then see if
- * the FPGA appears to be running.
- */
-static int fpga_post_config_fn(int cookie)
-{
- int rc = 0;
-
- debug("%s:%d: FPGA post configuration\n", __func__, __LINE__);
-
- fpga_reset(true);
- udelay(100);
- fpga_reset(false);
- udelay(100);
-
- return rc;
-}
-
-static int fpga_clk_fn(int assert_clk, int flush, int cookie)
-{
- /*
- * No dedicated clock signal on x600 (data & clock generated)
- * in SSP interface. So we don't have to do anything here.
- */
- return assert_clk;
-}
-
-static int fpga_wr_fn(int assert_write, int flush, int cookie)
-{
- struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE;
- static int count;
- static u16 data;
-
- /*
- * First collect 16 bits of data
- */
- data = data << 1;
- if (assert_write)
- data |= 1;
-
- /*
- * If 16 bits are not available, return for more bits
- */
- count++;
- if (count != 16)
- return assert_write;
-
- count = 0;
-
- /*
- * Wait for Tx-FIFO to become ready
- */
- while (!(readl(&ssp->sspsr) & SSPSR_TNF))
- ;
-
- /* Send 16 bits to FPGA via SSP bus */
- writel(data, &ssp->sspdr);
-
- return assert_write;
-}
-
-static xilinx_spartan3_slave_serial_fns x600_fpga_fns = {
- fpga_pre_config_fn,
- fpga_pgm_fn,
- fpga_clk_fn,
- fpga_init_fn,
- fpga_done_fn,
- fpga_wr_fn,
- fpga_post_config_fn,
-};
-
-static xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
- XILINX_XC3S1200E_DESC(slave_serial, &x600_fpga_fns, 0)
-};
-
-/*
- * Initialize the SelectMap interface. We assume that the mode and the
- * initial state of all of the port pins have already been set!
- */
-static void fpga_serialslave_init(void)
-{
- debug("%s:%d: Initialize serial slave interface\n", __func__, __LINE__);
- fpga_pgm_fn(false, false, 0); /* make sure program pin is inactive */
-}
-
-static int expi_setup(int freq)
-{
- struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- int pll2_m, pll2_n, pll2_p, expi_x, expi_y;
-
- pll2_m = (freq * 2) / 1000;
- pll2_n = 15;
- pll2_p = 1;
- expi_x = 1;
- expi_y = 2;
-
- /*
- * Disable reset, Low compression, Disable retiming, Enable Expi,
- * Enable soft reset, DMA, PLL2, Internal
- */
- writel(EXPI_CLK_CFG_LOW_COMPR | EXPI_CLK_CFG_CLK_EN | EXPI_CLK_CFG_RST |
- EXPI_CLK_SYNT_EN | EXPI_CLK_CFG_SEL_PLL2 |
- EXPI_CLK_CFG_INT_CLK_EN | (expi_y << 16) | (expi_x << 24),
- &misc->expi_clk_cfg);
-
- /*
- * 6 uA, Internal feedback, 1st order, Non-dithered, Sample Parameters,
- * Enable PLL2, Disable reset
- */
- writel((pll2_m << 24) | (pll2_p << 8) | (pll2_n), &misc->pll2_frq);
- writel(PLL2_CNTL_6UA | PLL2_CNTL_SAMPLE | PLL2_CNTL_ENABLE |
- PLL2_CNTL_RESETN | PLL2_CNTL_LOCK, &misc->pll2_cntl);
-
- /*
- * Disable soft reset
- */
- clrbits_le32(&misc->expi_clk_cfg, EXPI_CLK_CFG_RST);
-
- return 0;
-}
-
-/*
- * Initialize the fpga
- */
-int x600_init_fpga(void)
-{
- struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE;
- struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
-
- /* Enable SSP2 clock */
- writel(readl(&misc->periph1_clken) | MISC_SSP2ENB | MISC_GPIO4ENB,
- &misc->periph1_clken);
-
- /* Set EXPI clock to 45 MHz */
- expi_setup(45000);
-
- /* Configure GPIO directions */
- gpio_direction_output(CONFIG_SYS_FPGA_PROG, 0);
- gpio_direction_input(CONFIG_SYS_FPGA_DONE);
-
- writel(SSPCR0_DSS_16BITS, &ssp->sspcr0);
- writel(SSPCR1_SSE, &ssp->sspcr1);
-
- /*
- * Set lowest prescale divisor value (CPSDVSR) of 2 for max download
- * speed.
- *
- * Actual data clock rate is: 80MHz / (CPSDVSR * (SCR + 1))
- * With CPSDVSR at 2 and SCR at 0, the maximume clock rate is 40MHz.
- */
- writel(2, &ssp->sspcpsr);
-
- fpga_init();
- fpga_serialslave_init();
-
- debug("%s:%d: Adding fpga 0\n", __func__, __LINE__);
- fpga_add(fpga_xilinx, &fpga[0]);
-
- return 0;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-int x600_init_fpga(void);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2009
- * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
- *
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-#include <common.h>
-#include <flash.h>
-#include <init.h>
-#include <micrel.h>
-#include <nand.h>
-#include <net.h>
-#include <netdev.h>
-#include <phy.h>
-#include <rtc.h>
-#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_defs.h>
-#include <asm/arch/spr_misc.h>
-#include <linux/mtd/fsmc_nand.h>
-#include "fpga.h"
-
-static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];
-
-int board_init(void)
-{
- /*
- * X600 is equipped with an M41T82 RTC. This RTC has the
- * HT bit (Halt Update), which needs to be cleared upon
- * power-up. Otherwise the RTC is halted.
- */
- rtc_reset();
-
- return spear_board_init(MACH_TYPE_SPEAR600);
-}
-
-int board_late_init(void)
-{
- /*
- * Monitor and env protection on by default
- */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE +
- CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN +
- 2 * CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
-
- /* Init FPGA subsystem */
- x600_init_fpga();
-
- return 0;
-}
-
-/*
- * board_nand_init - Board specific NAND initialization
- * @nand: mtd private chip structure
- *
- * Called by nand_init_chip to initialize the board specific functions
- */
-
-void board_nand_init(void)
-{
- struct misc_regs *const misc_regs_p =
- (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- struct nand_chip *nand = &nand_chip[0];
-
- if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS))
- fsmc_nand_init(nand);
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- unsigned short id1, id2;
-
- /* check whether KSZ9031 or AR8035 has to be configured */
- id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
- id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
-
- if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
- /* PHY configuration for Micrel KSZ9031 */
- printf("PHY KSZ9031 detected - ");
-
- phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);
-
- /* control data pad skew - devaddr = 0x02, register = 0x04 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC,
- 0x0000);
- /* rx data pad skew - devaddr = 0x02, register = 0x05 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC,
- 0x0000);
- /* tx data pad skew - devaddr = 0x02, register = 0x05 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC,
- 0x0000);
- /* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */
- ksz9031_phy_extended_write(phydev, 0x02,
- MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
- MII_KSZ9031_MOD_DATA_NO_POST_INC,
- 0x03FF);
- } else {
- /* PHY configuration for Vitesse VSC8641 */
- printf("PHY VSC8641 detected - ");
-
- /* Extended PHY control 1, select GMII */
- phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
-
- /* Software reset necessary after GMII mode selction */
- phy_reset(phydev);
-
- /* Enable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
-
- /* 17e: Enhanced LED behavior, needs to be written twice */
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
-
- /* 16e: Enhanced LED method select */
- phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
-
- /* Disable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
-
- /* Enable clock output pin */
- phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
- }
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- int ret = 0;
-
- if (designware_initialize(CONFIG_SPEAR_ETHBASE,
- PHY_INTERFACE_MODE_GMII) >= 0)
- ret++;
-
- return ret;
-}
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_TARGET_SPEAR600=y
-CONFIG_SYS_TEXT_BASE=0x00700000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING="-SPEAr"
-CONFIG_SYS_EXTRA_OPTIONS="SPEAR600"
-CONFIG_BOOTDELAY=1
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Hit SPACE in %d seconds to stop autoboot.\n"
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock3 rootfstype=jffs2"
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xF8040000
-CONFIG_SYS_I2C_DW=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_GIGE=y
-CONFIG_ETH_DESIGNWARE=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_TARGET_SPEAR600=y
-CONFIG_SYS_TEXT_BASE=0x00700000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_IDENT_STRING="-SPEAr"
-CONFIG_SYS_EXTRA_OPTIONS="SPEAR600"
-CONFIG_BOOTDELAY=1
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock7 rootfstype=jffs2"
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_I2C_DW=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_GIGE=y
-CONFIG_ETH_DESIGNWARE=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_TARGET_SPEAR600=y
-CONFIG_SYS_TEXT_BASE=0x00700000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING="-SPEAr"
-CONFIG_SYS_EXTRA_OPTIONS="SPEAR600,USBTTY"
-CONFIG_BOOTDELAY=-1
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock3 rootfstype=jffs2"
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xF8040000
-CONFIG_SYS_I2C_DW=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_GIGE=y
-CONFIG_ETH_DESIGNWARE=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_USB=y
-CONFIG_USB_GADGET=y
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_TARGET_SPEAR600=y
-CONFIG_SYS_TEXT_BASE=0x00700000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_IDENT_STRING="-SPEAr"
-CONFIG_SYS_EXTRA_OPTIONS="SPEAR600,USBTTY"
-CONFIG_BOOTDELAY=-1
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock7 rootfstype=jffs2"
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_I2C_DW=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_GIGE=y
-CONFIG_ETH_DESIGNWARE=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_USB=y
-CONFIG_USB_GADGET=y
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_SYS_THUMB_BUILD=y
-# CONFIG_SPL_USE_ARCH_MEMCPY is not set
-# CONFIG_SPL_USE_ARCH_MEMSET is not set
-CONFIG_TARGET_X600=y
-CONFIG_SYS_TEXT_BASE=0x00800040
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SPL_TEXT_BASE=0xd2800b00
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SYS_BOOTCOUNT_ADDR=0xD2801FF8
-CONFIG_SPL=y
-CONFIG_IDENT_STRING="-SPEAr"
-CONFIG_BOOTDELAY=3
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Hit SPACE in %d seconds to stop autoboot.\n"
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_MISC_INIT_R=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="X600> "
-CONFIG_CMD_IMLS=y
-CONFIG_LOOPW=y
-CONFIG_CMD_MX_CYCLIC=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_SAVES=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:64M(ubi0),64M(ubi1)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xF8060000
-CONFIG_ENV_ADDR_REDUND=0xF8070000
-CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_FPGA_XILINX=y
-CONFIG_FPGA_SPARTAN3=y
-CONFIG_SYS_I2C_DW=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_PHY_ADDR_ENABLE=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ90X1=y
-CONFIG_ETH_DESIGNWARE=y
-CONFIG_MII=y
-CONFIG_RTC_M41T62=y
-CONFIG_CONS_INDEX=0
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_BCH=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-
-SPEAr (Structured Processor Enhanced Architecture).
-
-SPEAr600 is also known as SPEArPlus and SPEAr300 is also known as SPEArBasic
-
-The SPEAr SoC family embeds a customizable logic that can be programmed
-one-time by a customer at silicon mask level (i.e. not at runtime!).
-
-U-Boot supports four SoCs: SPEAr600, SPEAr3xx
-
-All 4 SoCs (SPEAr3xx and SPEAr600) share common peripherals. SPEAr300 and
-SPEAr600 do not have EMI.
-
-1. ARM926ejs core based (sp600 has two cores, the 2nd handled only in Linux)
-2. FastEthernet (sp600 has Gbit version, but same controller - GMAC)
-3. USB Host
-4. USB Device
-5. NAND controller (FSMC)
-6. Serial NOR ctrl
-7. I2C
-8. SPI
-9. CLCD
-10. others ..
-
-Everything is supported in Linux.
-u-boot is currently not supporting all peripeharls (just a few as listed below).
-1. USB Device
-2. NAND controller (FSMC)
-3. Serial Memory Interface
-4. EMI (Parallel NOR interface)
-4. I2C
-5. UART
-
-Build options
- make spear320_config
- spear320 build with environment variables placed at default
- location i.e. Serial NOR device
- make spear320_pnor_config
- This option generates a uboot image that supports emi controller
- for CFI compliant parallel NOR flash. Environment variables are
- placed in Parallel NOR device
- make spear320_nand_config
- spear320 build with environment variables placed in NAND device
- make spear320_usbtty_config
- spear320 build with usbtty terminal as default and environment
- placed at default location
- make spear320_usbtty_pnor_config
- spear320 build with usbtty terminal as default and environment
- placed in pnor device
- make spear320_usbtty_nand_config
- Build with usbtty terminal as default and environment placed in
- NAND device
- make spear300_config
- make spear300_nand_config
- make spear300_usbtty_config
- make spear300_usbtty_nand_config
- make spear310_config
- make spear310_pnor_config
- make spear310_nand_config
- make spear310_usbtty_config
- make spear310_usbtty_pnor_config
- make spear310_usbtty_nand_config
- make spear600_config
- make spear600_nand_config
- make spear600_usbtty_config
- make spear600_usbtty_nand_config
-
-Mac id storage and retrieval in spear platforms
-
-Please read doc/README.enetaddr for the implementation guidelines for mac id
-usage. Basically, environment has precedence over board specific storage. The
-ethaddr beeing used for the network interface is always taken only from
-environment variables. Although, we can check the mac id programmed in i2c
-memory by using chip_config command
obj-$(CONFIG_RZA1_GPIO) += gpio-rza1.o
obj-$(CONFIG_S5P) += s5p_gpio.o
obj-$(CONFIG_SANDBOX_GPIO) += sandbox.o
-obj-$(CONFIG_SPEAR_GPIO) += spear_gpio.o
obj-$(CONFIG_TEGRA_GPIO) += tegra_gpio.o
obj-$(CONFIG_TEGRA186_GPIO) += tegra186_gpio.o
obj-$(CONFIG_DA8XX_GPIO) += da8xx_gpio.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2012 Stefan Roese <sr@denx.de>
- */
-
-/*
- * Driver for SPEAr600 GPIO controller
- */
-
-#include <common.h>
-#include <malloc.h>
-#include <asm/arch/hardware.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <errno.h>
-
-static int gpio_direction(unsigned gpio,
- enum gpio_direction direction)
-{
- struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE;
- u32 val;
-
- val = readl(®s->gpiodir);
-
- if (direction == GPIO_DIRECTION_OUT)
- val |= 1 << gpio;
- else
- val &= ~(1 << gpio);
-
- writel(val, ®s->gpiodir);
-
- return 0;
-}
-
-int gpio_set_value(unsigned gpio, int value)
-{
- struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE;
-
- if (value)
- writel(1 << gpio, ®s->gpiodata[DATA_REG_ADDR(gpio)]);
- else
- writel(0, ®s->gpiodata[DATA_REG_ADDR(gpio)]);
-
- return 0;
-}
-
-int gpio_get_value(unsigned gpio)
-{
- struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE;
- u32 val;
-
- val = readl(®s->gpiodata[DATA_REG_ADDR(gpio)]);
-
- return !!val;
-}
-
-int gpio_request(unsigned gpio, const char *label)
-{
- if (gpio >= SPEAR_GPIO_COUNT)
- return -EINVAL;
-
- return 0;
-}
-
-int gpio_free(unsigned gpio)
-{
- return 0;
-}
-
-void gpio_toggle_value(unsigned gpio)
-{
- gpio_set_value(gpio, !gpio_get_value(gpio));
-}
-
-int gpio_direction_input(unsigned gpio)
-{
- return gpio_direction(gpio, GPIO_DIRECTION_IN);
-}
-
-int gpio_direction_output(unsigned gpio, int value)
-{
- int ret = gpio_direction(gpio, GPIO_DIRECTION_OUT);
-
- if (ret < 0)
- return ret;
-
- gpio_set_value(gpio, value);
- return 0;
-}
controller is used in various SoCs, e.g. the ST SPEAr, Altera
SoCFPGA, Synopsys ARC700 and some Intel x86 SoCs.
-config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
- bool "DW I2C Enable Status Register not supported"
- depends on SYS_I2C_DW && \
- (TARGET_SPEAR600 || TARGET_X600)
- default y
- help
- Some versions of the Designware I2C controller do not support the
- enable status register. This config option can be enabled in such
- cases.
-
config SYS_I2C_ASPEED
bool "Aspeed I2C Controller"
depends on DM_I2C && ARCH_ASPEED
*/
#define DW_I2C_COMP_TYPE 0x44570140
-#ifdef CONFIG_SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED
-static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
-{
- u32 ena = enable ? IC_ENABLE_0B : 0;
-
- writel(ena, &i2c_base->ic_enable);
-
- return 0;
-}
-#else
static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable)
{
u32 ena = enable ? IC_ENABLE_0B : 0;
return -ETIMEDOUT;
}
-#endif
/* High and low times in different speed modes (in ns) */
enum {
return 0;
}
-#ifndef CONFIG_SPL_BUILD
-/*
- * fsmc_nand_switch_ecc - switch the ECC operation between different engines
- *
- * @eccstrength - the number of bits that could be corrected
- * (1 - HW, 4 - SW BCH4)
- */
-int fsmc_nand_switch_ecc(uint32_t eccstrength)
-{
- struct nand_chip *nand;
- struct mtd_info *mtd;
- int err;
-
- /*
- * This functions is only called on SPEAr600 platforms, supporting
- * 1 bit HW ECC. The BCH8 HW ECC (FSMC_VER8) from the ST-Ericsson
- * Nomadik SoC is currently supporting this fsmc_nand_switch_ecc()
- * function, as it doesn't need to switch to a different ECC layout.
- */
- mtd = get_nand_dev_by_index(nand_curr_device);
- nand = mtd_to_nand(mtd);
-
- /* Setup the ecc configurations again */
- if (eccstrength == 1) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.bytes = 3;
- nand->ecc.strength = 1;
- nand->ecc.layout = &fsmc_ecc1_layout;
- nand->ecc.calculate = fsmc_read_hwecc;
- nand->ecc.correct = nand_correct_data;
- } else if (eccstrength == 4) {
- /*
- * .calculate .correct and .bytes will be set in
- * nand_scan_tail()
- */
- nand->ecc.mode = NAND_ECC_SOFT_BCH;
- nand->ecc.strength = 4;
- nand->ecc.layout = NULL;
- } else {
- printf("Error: ECC strength %d not supported!\n", eccstrength);
- }
-
- /* Update NAND handling after ECC mode switch */
- err = nand_scan_tail(mtd);
-
- return err;
-}
-#endif /* CONFIG_SPL_BUILD */
-
int fsmc_nand_init(struct nand_chip *nand)
{
static int chip_nr;
obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
obj-$(CONFIG_USB_EHCI_MSM) += ehci-msm.o
obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
-obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
obj-$(CONFIG_USB_EHCI_VF) += ehci-vf.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Armando Visconti, ST Micoelectronics, <armando.visconti@st.com>.
- *
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- */
-
-#include <common.h>
-#include <log.h>
-#include <asm/io.h>
-#include <usb.h>
-#include <linux/delay.h>
-#include "ehci.h"
-#include <asm/arch/hardware.h>
-#include <asm/arch/spr_misc.h>
-
-static void spear6xx_usbh_stop(void)
-{
- struct misc_regs *const misc_p =
- (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
- u32 periph1_rst = readl(misc_p->periph1_rst);
-
- periph1_rst |= PERIPH_USBH1 | PERIPH_USBH2;
- writel(periph1_rst, misc_p->periph1_rst);
-
- udelay(1000);
- periph1_rst &= ~(PERIPH_USBH1 | PERIPH_USBH2);
- writel(periph1_rst, misc_p->periph1_rst);
-}
-
-/*
- * Create the appropriate control structures to manage
- * a new EHCI host controller.
- */
-int ehci_hcd_init(int index, enum usb_init_type init,
- struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
- u32 ehci = 0;
-
- switch (index) {
- case 0:
- ehci = CONFIG_SYS_UHC0_EHCI_BASE;
- break;
- case 1:
- ehci = CONFIG_SYS_UHC1_EHCI_BASE;
- break;
- default:
- printf("ERROR: wrong controller index!\n");
- break;
- };
-
- *hccr = (struct ehci_hccr *)(ehci + 0x100);
- *hcor = (struct ehci_hcor *)((uint32_t) *hccr +
- HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
-
- debug("SPEAr-ehci: init hccr %x and hcor %x hc_length %d\n",
- (uint32_t)*hccr, (uint32_t)*hcor,
- (uint32_t)HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
-
- return 0;
-}
-
-/*
- * Destroy the appropriate control structures corresponding
- * the the EHCI host controller.
- */
-int ehci_hcd_stop(int index)
-{
-#if defined(CONFIG_SPEAR600)
- spear6xx_usbh_stop();
-#endif
-
- return 0;
-}
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
- */
-
-#ifndef _SPEAR_COMMON_H
-#define _SPEAR_COMMON_H
-/*
- * Common configurations used for both spear3xx as well as spear6xx
- */
-
-/* U-Boot Load Address */
-
-/* Ethernet driver configuration */
-#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
-
-/* USBD driver configuration */
-#if defined(CONFIG_SPEAR_USBTTY)
-#define CONFIG_DW_UDC
-#define CONFIG_USB_DEVICE
-#define CONFIG_USBD_HS
-#define CONFIG_USB_TTY
-
-#define CONFIG_USBD_PRODUCT_NAME "SPEAr SoC"
-#define CONFIG_USBD_MANUFACTURER "ST Microelectronics"
-
-#endif
-
-#define CONFIG_EXTRA_ENV_USBTTY "usbtty=cdc_acm\0"
-
-/* I2C driver configuration */
-#define CONFIG_SYS_I2C
-#if defined(CONFIG_SPEAR600)
-#define CONFIG_SYS_I2C_BASE 0xD0200000
-#endif
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x02
-
-#define CONFIG_I2C_CHIPADDRESS 0x50
-
-/* Timer, HZ specific defines */
-
-/* Flash configuration */
-#if defined(CONFIG_FLASH_PNOR)
-#define CONFIG_SPEAR_EMI
-#else
-#define CONFIG_ST_SMI
-#endif
-
-#if defined(CONFIG_ST_SMI)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2
-#define CONFIG_SYS_FLASH_BASE 0xF8000000
-#define CONFIG_SYS_CS1_FLASH_BASE 0xF9000000
-#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000
-#define CONFIG_SYS_FLASH_ADDR_BASE {CONFIG_SYS_FLASH_BASE, \
- CONFIG_SYS_CS1_FLASH_BASE}
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ)
-
-#endif
-
-/*
- * Serial Configuration (PL011)
- * CONFIG_PL01x_PORTS is defined in specific files
- */
-#define CONFIG_PL011_CLOCK (48 * 1000 * 1000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \
- 57600, 115200 }
-
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/* NAND FLASH Configuration */
-#define CONFIG_SYS_NAND_SELF_INIT
-#define CONFIG_NAND_FSMC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/*
- * Default Environment Varible definitions
- */
-
-/*
- * U-Boot Environment placing definitions.
- */
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-#ifdef CONFIG_ST_SMI
-/*
- * Environment is in serial NOR flash
- */
-#define CONFIG_SYS_MONITOR_LEN 0x00040000
-#define CONFIG_FSMTDBLK "/dev/mtdblock3 "
-
-#define CONFIG_BOOTCOMMAND "bootm 0xf8050000"
-
-#elif defined(CONFIG_SPEAR_EMI)
-/*
- * Environment is in parallel NOR flash
- */
-#define CONFIG_SYS_MONITOR_LEN 0x00060000
-#define CONFIG_FSMTDBLK "/dev/mtdblock3 "
-
-#define CONFIG_BOOTCOMMAND "cp.b 0x50080000 0x1600000 " \
- "0x4C0000; bootm 0x1600000"
-#endif
-#elif defined(CONFIG_ENV_IS_IN_NAND)
-/*
- * Environment is in NAND
- */
-
-#define CONFIG_ENV_RANGE 0x10000
-#define CONFIG_FSMTDBLK "/dev/mtdblock7 "
-
-#define CONFIG_BOOTCOMMAND "nand read.jffs2 0x1600000 " \
- "0x80000 0x4C0000; " \
- "bootm 0x1600000"
-#endif
-
-#define CONFIG_NFSBOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):" \
- "$(netmask):$(hostname):$(netdev):off " \
- "console=ttyAMA0,115200 $(othbootargs);" \
- "bootm; "
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=ttyAMA0,115200 $(othbootargs);" \
- CONFIG_BOOTCOMMAND
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-/* Miscellaneous configurable options */
-#define CONFIG_BOOT_PARAMS_ADDR 0x00000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
-#define CONFIG_SYS_MALLOC_LEN (1024*1024)
-#define CONFIG_SYS_LOAD_ADDR 0x00800000
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/* Physical Memory Map */
-#define PHYS_SDRAM_1 0x00000000
-#define PHYS_SDRAM_1_MAXSIZE 0x40000000
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xD2800000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Vipin Kumar, STMicroelectronics, <vipin.kumar@st.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#if defined(CONFIG_USBTTY)
-#define CONFIG_SPEAR_USBTTY
-#endif
-
-#include <configs/spear-common.h>
-
-/* Serial Configuration (PL011) */
-#define CONFIG_SYS_SERIAL0 0xD0000000
-#define CONFIG_SYS_SERIAL1 0xD0080000
-#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \
- (void *)CONFIG_SYS_SERIAL1 }
-
-/* NAND flash configuration */
-#define CONFIG_SYS_FSMC_NAND_SP
-#define CONFIG_SYS_FSMC_NAND_8BIT
-#define CONFIG_SYS_NAND_BASE 0xD2000000
-
-/* Ethernet PHY configuration */
-
-/* Environment Settings */
-#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_USBTTY
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2009, STMicroelectronics - All Rights Reserved
- * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics.
- *
- * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_SPEAR600 /* SPEAr600 SoC */
-#define CONFIG_X600 /* on X600 board */
-
-#include <asm/arch/hardware.h>
-
-/* Timer, HZ specific defines */
-#define CONFIG_SYS_HZ_CLOCK 8300000
-
-#define CONFIG_SYS_FLASH_BASE 0xf8000000
-/* Reserve 8KiB for SPL */
-#define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */
-#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO
-#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \
- CONFIG_SYS_SPL_LEN)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN 0x60000
-
-/* Serial Configuration (PL011) */
-#define CONFIG_SYS_SERIAL0 0xD0000000
-#define CONFIG_SYS_SERIAL1 0xD0080000
-#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \
- (void *)CONFIG_SYS_SERIAL1 }
-#define CONFIG_PL011_CLOCK (48 * 1000 * 1000)
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \
- 57600, 115200 }
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/* NOR FLASH config options */
-#define CONFIG_ST_SMI
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000
-#define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ)
-
-/* NAND FLASH config options */
-#define CONFIG_NAND_FSMC
-#define CONFIG_SYS_NAND_SELF_INIT
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE
-#define CONFIG_MTD_ECC_SOFT
-#define CONFIG_SYS_FSMC_NAND_8BIT
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_NAND_ECC_BCH
-
-/* UBI/UBI config options */
-
-/* Ethernet config options */
-#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
-
-#define CONFIG_SPEAR_GPIO
-
-/* I2C config options */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_BASE 0xD0200000
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x02
-#define CONFIG_I2C_CHIPADDRESS 0x50
-
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/* FPGA config options */
-#define CONFIG_FPGA_COUNT 1
-
-/* USB EHCI options */
-#define CONFIG_USB_EHCI_SPEAR
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-
-/*
- * U-Boot Environment placing definitions.
- */
-
-/* Miscellaneous configurable options */
-#define CONFIG_BOOT_PARAMS_ADDR 0x00000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
-#define CONFIG_SYS_MALLOC_LEN (8 << 20)
-#define CONFIG_SYS_LOAD_ADDR 0x00800000
-
-#define CONFIG_HOSTNAME "x600"
-#define CONFIG_UBI_PART ubi0
-#define CONFIG_UBIFS_VOLUME rootfs
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "u-boot_addr=1000000\0" \
- "u-boot=" CONFIG_HOSTNAME "/u-boot.spr\0" \
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};" \
- "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \
- "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " ${filesize};" \
- "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize}\0" \
- "upd=run load update\0" \
- "ubifs=" CONFIG_HOSTNAME "/ubifs.img\0" \
- "part=" __stringify(CONFIG_UBI_PART) "\0" \
- "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \
- "load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \
- "update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \
- " ${filesize}\0" \
- "upd_ubifs=run load_ubifs update_ubifs\0" \
- "init_ubifs=nand erase.part ubi0;ubi part ${part};" \
- "ubi create ${vol} 4000000\0" \
- "netdev=eth0\0" \
- "rootpath=/opt/eldk-4.2/arm\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "boot_part=0\0" \
- "altbootcmd=if test $boot_part -eq 0;then " \
- "echo Switching to partition 1!;" \
- "setenv boot_part 1;" \
- "else; " \
- "echo Switching to partition 0!;" \
- "setenv boot_part 0;" \
- "fi;" \
- "saveenv;boot\0" \
- "ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \
- "root=ubi0:rootfs rootfstype=ubifs\0" \
- "kernel=" CONFIG_HOSTNAME "/uImage\0" \
- "kernel_fs=/boot/uImage \0" \
- "kernel_addr=1000000\0" \
- "dtb=" CONFIG_HOSTNAME "/" \
- CONFIG_HOSTNAME ".dtb\0" \
- "dtb_fs=/boot/" CONFIG_HOSTNAME ".dtb\0" \
- "dtb_addr=1800000\0" \
- "load_kernel=tftp ${kernel_addr} ${kernel}\0" \
- "load_dtb=tftp ${dtb_addr} ${dtb}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcon=setenv bootargs ${bootargs} console=ttyAMA0," \
- "${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "net_nfs=run load_dtb load_kernel; " \
- "run nfsargs addip addcon addmtd addmisc;" \
- "bootm ${kernel_addr} - ${dtb_addr}\0" \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
- "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \
- " addcon addmisc addmtd;" \
- "bootm ${kernel_addr} - ${dtb_addr}\0" \
- "ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \
- "ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \
- "ubifsload ${dtb_addr} ${dtb_fs};\0" \
- "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \
- "addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \
- "bootcmd=run nand_ubifs\0" \
- "\0"
-
-/* Physical Memory Map */
-#define PHYS_SDRAM_1 0x00000000
-#define PHYS_SDRAM_1_MAXSIZE 0x40000000
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SRAM_BASE 0xd2800000
-/* Preserve the last 2 lwords for the boot-counter */
-#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8)
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/*
- * SPL related defines
- */
-#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00)
-#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear"
-
-/*
- * Please select/define only one of the following
- * Each definition corresponds to a supported DDR chip.
- * DDR configuration is based on the following selection
- */
-#define CONFIG_DDR_MT47H64M16 1
-#define CONFIG_DDR_MT47H32M16 0
-#define CONFIG_DDR_MT47H128M8 0
-
-/*
- * Synchronous/Asynchronous operation of DDR
- *
- * Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation
- * Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation
- * Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation
- */
-#define CONFIG_DDR_2HCLK 1
-#define CONFIG_DDR_HCLK 0
-#define CONFIG_DDR_PLL2 0
-
-/*
- * xxx_BOOT_SUPPORTED macro defines whether a booting type is supported
- * or not. Modify/Add to only these macros to define new boot types
- */
-#define USB_BOOT_SUPPORTED 0
-#define PCIE_BOOT_SUPPORTED 0
-#define SNOR_BOOT_SUPPORTED 1
-#define NAND_BOOT_SUPPORTED 1
-#define PNOR_BOOT_SUPPORTED 0
-#define TFTP_BOOT_SUPPORTED 0
-#define UART_BOOT_SUPPORTED 0
-#define SPI_BOOT_SUPPORTED 0
-#define I2C_BOOT_SUPPORTED 0
-#define MMC_BOOT_SUPPORTED 0
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff
