The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
cn9132-db-B.dtb \
cn9130-crb-A.dtb \
cn9130-crb-B.dtb \
- ac5-98dx35xx-rd.dtb
+ ac5-98dx35xx-rd.dtb \
+ ac5-98dx35xx-atl-x240.dtb
endif
dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "ac5-98dx35xx.dtsi"
+
+/ {
+ model = "Allied Telesis x240";
+ compatible = "alliedtelesis,x240", "marvell,ac5x", "marvell,ac5";
+
+ aliases {
+ serial0 = &uart0;
+ spiflash0 = &spiflash0;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ spi0 = &spi0;
+ i2c0 = &i2c0;
+ usb0 = &usb0;
+ pinctrl0 = &pinctrl0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ boot-board {
+ compatible = "atl,boot-board";
+ present-gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ override-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ fault {
+ label = "fault:red";
+ gpios = <&system_gpio 11 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+};
+
+&nand {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins>;
+
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@user {
+ reg = <0x00000000 0x10000000>;
+ label = "user";
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ mux@71 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nxp,pca9546";
+ reg = <0x71>;
+ i2c-mux-idle-disconnect;
+ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* MPP36 */
+ status = "okay";
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ hwmon@2e {
+ compatible = "adi,adt7476";
+ reg = <0x2e>;
+ };
+
+ rtc@68 {
+ compatible = "adi,max31331";
+ reg = <0x68>;
+ };
+
+ system_gpio: gpio@27 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells= <2>;
+ reg = <0x27>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <25 IRQ_TYPE_LEVEL_LOW>; /* MPP25 */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+ spiflash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&gpio0 {
+ phy-reset {
+ gpio-hog;
+ gpios = <19 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "phy-reset";
+ };
+
+ usb-en {
+ gpio-hog;
+ gpios = <28 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-en";
+ };
+
+ led-oe-n {
+ gpio-hog;
+ gpios = <23 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "led-oe-n";
+ };
+};
+
+&gpio1 {
+ nand-protect {
+ gpio-hog;
+ gpios = <8 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "nand-protect";
+ };
+};
+
+&pinctrl0 {
+ /*
+ * MPP Bus: MPP#
+ * NF_IO [0-7]
+ * NF_Wen [8]
+ * NF_ALE [9]
+ * NF_CLE [10]
+ * NF_Cen [11]
+ * QSPI_SCK/SPI0_SCK [12]
+ * QSPI_CSn/SPI0_CSn [13]
+ * QSPI_DIO[0]/SPI0_MOSI [14]
+ * QSPI_DIO[1]/SPI0_MISO [15]
+ * NF_Ren [16]
+ * NF_RBn [17]
+ * WD_INTn [18]
+ * B_B_OVRIDE_N [19]
+ * GREEN_SW_N [20]
+ * PHY_INT_N[0] [21]
+ * SPI_WPn [22]
+ * LED_OE_N [23]
+ * USB_PWR_FLT_N [24]
+ * SFP_INT_N [25]
+ * I2C0_SCL [26]
+ * I2C0_SDA [27]
+ * USB_EN [28]
+ * MONITOR_INT_N [29]
+ * XM1_MDC [30]
+ * XM1_MDIO [31]
+ * UA0_RXD [32]
+ * UA0_TXD [33]
+ * PHY_RST0n [34]
+ * TPM_INT_N [35]
+ * I2CMUX_RESET_N [36]
+ * SPI_SRAM_SEL_N [37]
+ * B_B_PRESENT [38]
+ * SPI_FLASH_SEL_N [39]
+ * NF_WP_N [40]
+ * POE_INT_N [41]
+ * PoE_RST_N [42]
+ * LED0_CLK [43]
+ * LED0_STB [44]
+ * LED0_DATA [45]
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
+ 0xff 0xff 1 1 1 1 0xff 0xff 0 0
+ 0 0 0 0 0 0 1 1 0 0
+ 1 1 1 1 0 0 0 0 0 0
+ 0 0 0 1 1 1 >;
+
+ nand_pins: nand-pins {
+ marvell,pins = <0 1 2 3 4 5 6 7 8 9 10 11 16 17>;
+ marvell,function = <2>;
+ };
+};
bool "Support Allied Telesis x530"
select 88F6820
+config TARGET_X240
+ bool "Support Allied Telesis x240"
+ select ALLEYCAT_5
+
config TARGET_DB_XC3_24G4XG
bool "Support DB-XC3-24G4XG"
select 98DX3336
default "theadorable" if TARGET_THEADORABLE
default "a38x" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
+ default "x240" if TARGET_X240
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
default "turris_mox" if TARGET_TURRIS_MOX
default "controlcenterdc" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
+ default "x240" if TARGET_X240
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
default "CZ.NIC" if TARGET_TURRIS_MOX
default "gdsys" if TARGET_CONTROLCENTERDC
default "alliedtelesis" if TARGET_X530
+ default "alliedtelesis" if TARGET_X240
default "mikrotik" if TARGET_CRS3XX_98DX3236
default "Marvell" if TARGET_MVEBU_ALLEYCAT5
--- /dev/null
+X240 BOARD
+M: Chris Packham <chris.packham@alliedtelesis.co.nz>
+S: Maintained
+F: board/alliedtelesis/x240/
+F: arch/arm/dts/ac5-98dx35xx-rd.dts
+F: include/configs/x240.h
+F: configs/x240_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2022 Allied Telesis
+#
+
+obj-y += x240.o
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_TEXT_BASE=0x200000000
+CONFIG_SYS_MALLOC_LEN=0x900000
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x200FF0000
+CONFIG_TARGET_X240=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x00f80000
+CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="ac5-98dx35xx-atl-x240"
+CONFIG_SYS_LOAD_ADDR=0x220000000
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_MEMTEST=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_CLK=y
+CONFIG_CLK_MVEBU=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_PXA3XX=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_8K=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MAX313XX=y
+CONFIG_DM_SCSI=y
+CONFIG_SYS_NS16550=y
+CONFIG_MVEBU_A3700_SPI=y
+CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
+# CONFIG_FAT_WRITE is not set
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2022 Allied Telesis
+ */
+
+#ifndef __X240_H_
+#define __X240_H_
+
+#include <asm/arch/soc.h>
+
+/* additions for new ARM relocation support */
+#define CFG_SYS_SDRAM_BASE 0x200000000
+
+#define CFG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200, 230400, 460800, 921600 }
+
+/* Default Env vars */
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#define CFG_EXTRA_ENV_SETTINGS \
+ BOOTENV \
+ "kernel_addr_r=0x202000000\0" \
+ "fdt_addr_r=0x201000000\0" \
+ "ramdisk_addr_r=0x206000000\0" \
+ "fdtfile=marvell/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CFG_SYS_TCLK 325000000
+
+#endif /* __X240_H_ */
projects / u-boot.git / commitdiff
