ARM: imx6q_logic: Remove legacy pinmuxing code from board file.

With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.

This patch removes the legacy pinmuxing code from the board file.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c
index 4bacd8660a96ea7453c76312529b3fd7e9f4ff54..3c1a3a9fa24be8970348c03e62cb2856941ea596 100644 (file)
--- a/board/logicpd/imx6/imx6logic.c
+++ b/board/logicpd/imx6/imx6logic.c
@@ -42,32 +42,6 @@ int dram_init(void)
        return 0;
 }
 
-static iomux_v3_cfg_t const uart1_pads[] = {
-       MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart2_pads[] = {
-       MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_SD4_DAT5__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_SD4_DAT6__UART2_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart3_pads[] = {
-       MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
-       imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-       imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
-       imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
-}
-
 static iomux_v3_cfg_t const nand_pads[] = {
        MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
        MX6_PAD_NANDF_ALE__NAND_ALE  | MUX_PAD_CTRL(NAND_PAD_CTRL),
@@ -135,7 +109,6 @@ int overwrite_console(void)
 
 int board_early_init_f(void)
 {
-       setup_iomux_uart();
        setup_nand_pins();
        return 0;
 }
@@ -177,36 +150,6 @@ int spl_start_uboot(void)
 }
 #endif
 
-/* SD interface */
-#define USDHC_PAD_CTRL                                                 \
-       (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |   \
-        PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-static iomux_v3_cfg_t const usdhc1_pads[] = {
-       MX6_PAD_SD1_CLK__SD1_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD1_CMD__SD1_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc2_pads[] = {
-       MX6_PAD_SD2_DAT0__SD2_DATA0     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD2_DAT1__SD2_DATA1     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD2_DAT2__SD2_DATA2     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD2_DAT3__SD2_DATA3     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD2_CLK__SD2_CLK        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_SD2_CMD__SD2_CMD        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-       MX6_PAD_GPIO_4__GPIO1_IO04      | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg usdhc_cfg[] = {
-       {USDHC1_BASE_ADDR}, /* SOM */
-       {USDHC2_BASE_ADDR}  /* Baseboard */
-};
-
 void board_boot_order(u32 *spl_boot_list)
 {
        struct src *psrc = (struct src *)SRC_BASE_ADDR;
@@ -236,34 +179,6 @@ void board_boot_order(u32 *spl_boot_list)
        spl_boot_list[2] = BOOT_DEVICE_BOARD;
 }
 
-int board_mmc_init(bd_t *bis)
-{
-       struct src *psrc = (struct src *)SRC_BASE_ADDR;
-       unsigned int reg = readl(&psrc->sbmr1) >> 11;
-       /*
-        * Upon reading BOOT_CFG register the following map is done:
-        * Bit 11 and 12 of BOOT_CFG register can determine the current
-        * mmc port
-        * 0x1                  SD1-SOM
-        * 0x2                  SD2-Baseboard
-        */
-
-       reg &= 0x3; /* Only care about bottom 2 bits */
-
-       switch (reg) {
-       case 0:
-               SETUP_IOMUX_PADS(usdhc1_pads);
-               break;
-       case 1:
-               SETUP_IOMUX_PADS(usdhc2_pads);
-               break;
-       }
-
-       return 0;
-}
-
-#endif
-
 static void ccgr_init(void)
 {
        struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;